3D printed porous PEEK created via fused filament fabrication for osteoconductive orthopaedic surfaces

Experimental investigation on punch shear strength of poly lactic acid specimens for biomedical applications

The designed biomedical implants require excellent shear strength primarily for mechanical stability against forces in human body. However, metallic implants undergo stress shielding with release of toxic ions in the body. Thus, Fused Deposition Modeling (FDM) has made significant progress in the biomedical field through the production of customized implants. The mechanical behavior is highly dependent on printing parameters, however, the effect of these parameters on punch shear strength of ASTM D732-02 standard specimens has not been explored. Thus, in the current study, the effect of infill density (IFD), printing speed (PTS), wall thickness (WLT), and layer thickness (LYT) has been investigated on the punch shear strength using Response Surface Methodology. The Analysis of Variance (ANOVA) has been performed for predicting statistical model with 95% confidence interval. During the statistical analysis, the terms with p-value lower than 0.05 were considered significant and the influence of process parameters has been examined using microscopic images. The surface plots have been used for discussing the effect of interactions between printing parameters. The statistical results revealed IFD as the most significant contributing factor, followed by PTS, LYT, and WLT. The study concluded by optimization of printing parameters for obtaining the highest punch shear strength.

In Vitro and In Vivo Evaluation of 3D Printed Poly(Ethylene Glycol) Dimethacrylate-Based Photocurable Hydrogel Platform for Bone Tissue Engineering

This study focuses to develop a unique hybrid hydrogel bioink formulation that incorporates poly(ethylene glycol) dimethacrylate (PEGDMA), gelatin (Gel), and methylcellulose (MC). This formulation achieves the necessary viscosity for extrusion-based three-dimensional (3D) printing of scaffolds intended for bone regeneration. After thorough optimization of the hybrid bioink system with Gel, three distinct scaffold groups are investigated in vitro: 0%, 3%, and 6% (w/v) Gel. These scaffold groups are examined for their morphology, mechanical strength, biodegradation, in vitro cell proliferation and differentiation, and in vivo bone formation using a rat cranial defect model. Among these scaffold compositions, the 3% Gel scaffold exhibits the most favorable characteristics, prompting further evaluation as a rat mesenchymal stem cell (rMSC) carrier in a critical-size cranial defect within a Lewis rat model. The compressive strength of all three scaffold groups range between 1 and 2 MPa. Notably, the inclusion of Gel in the scaffolds leads to enhanced bioactivity and cell adhesion. The Gel-containing scaffolds notably amplify osteogenic differentiation, as evidenced by alkaline phosphatase (ALP) and Western blot analyses. The in vivo results, as depicted by microcomputed tomography, showcase augmented osteogenesis within cell-seeded scaffolds, thus validating this innovative PEGDMA-based scaffold system as a promising candidate for cranial bone defect healing.

Bone ingrowth into a porous structure is achieved by preceding fibrogenesis and vascularization

Porous structures are frequently used in surgical implants to strengthen the interlocking power produced by bone ingrowth. Therefore, we aimed to elucidate the mechanism underlying bone ingrowth into a porous structure accompanied by vascularization. A nonbioactive polyetheretherketone implant with a 3D-printed porous structure was prepared and implanted in a bone hole created in the tibias of rabbits. We observed bone ingrowth in the same individual specimens immediately and at 2, 4, 8, and 12 weeks post-implantation using in-vivo computed tomography (CT). Furthermore, a detailed evaluation with blood vessels of each specimen at 2, 4, and 12 weeks was performed with ex-vivo CT and histological specimen. Additional histological evaluation was performed using thin sections of an implant made with thermoplastic polyurethane having the same structure. As a result, the bone invasion began after four weeks, when the construction of fibrous tissue and the spread of new blood vessels within the voids matured. As the bone matured in the load-bearing area, new blood vessels outside the bone matrix regressed. This longitudinal evaluation study suggests that preceding fibrogenesis and vascularization may be key in developing bone ingrowth. STATEMENT OF SIGNIFICANCE: A porous structure is an essential structure for dental and orthopedic implants because it provides strong fixation through bone invasion. Although it was known that vascularization was involved in this, the details were not known. This in vivo study revealed that in order for bone ingrowth to begin, a preparatory period of approximately 4 weeks was required to establish blood flow inside and outside the implant. Furthermore, it was confirmed that by spreading the fibrous structure in advance, it has an advantageous effect on the migration of cells involved in the formation of bones and blood vessels. We pointed out that it is necessary to consider fibrogenesis and vascularization when creating future implants.

Multiscale Mechanical Characterization of Polyether-2-ketone (PEKK) for Biomedical Application

Polyether-ether-2-ketone (PEKK) is a high-performance thermoplastic polymer used in various fields, from aerospace to medical applications, due to its exceptional mechanical and thermal properties. Nonetheless, the mechanical behavior of 3D-printed PEKK still deserves to be more thoroughly investigated, especially in view of its production by 3D printing, where mechanical properties measured at different scales are likely to be correlated to one another and to all play a major role in determining biomechanical properties, which include mechanical strength on one side and osteointegration ability on the other side. This work explores the mechanical behavior of 3D-printed PEKK through a multiscale approach, having performed both nanoindentation tests and standard tensile and compression tests, where a detailed view of strain distribution was achieved through Digital Image Correlation (DIC) techniques. Furthermore, for specimens tested up to failure, their fractured surfaces were analyzed through Scanning Electron Microscopy (SEM) to clearly outline fracture modes. Additionally, the internal structure of 3D-printed PEKK was explored through Computed Tomography (CT) imaging, providing a three-dimensional view of the internal structure and the presence of voids and other imperfections. Finally, surface morphology was analyzed through confocal microscopy. The multiscale approach adopted in the present work offers information about the global and local behavior of the PEKK, also assessing its material properties down to the nanoscale. Due to its novelty as a polymeric material, no previous studies have approached a multiscale analysis of 3D-printed PEKK. The findings of this study contribute to a comprehensive understanding of 3D-printed PEKK along with criteria for process optimization in order to customize its properties to meet specific application requirements. This research not only advances the knowledge of PEKK as a 3D-printing material but also provides insights into the multifaceted nature of multiscale material characterization.

Fatigue behaviour of load-bearing polymeric bone scaffolds: A review

Bone scaffolds play a crucial role in bone tissue engineering by providing mechanical support for the growth of new tissue while enduring static and fatigue loads. Although polymers possess favourable characteristics such as adjustable degradation rate, tissue-compatible stiffness, ease of fabrication, and low toxicity, their relatively low mechanical strength has limited their use in load-bearing applications. While numerous studies have focused on assessing the static strength of polymeric scaffolds, little research has been conducted on their fatigue properties. The current review presents a comprehensive study on the fatigue behaviour of polymeric bone scaffolds. The fatigue failure in polymeric scaffolds is discussed and the impact of material properties, topological features, loading conditions, and environmental factors are also examined. The present review also provides insight into the fatigue damage evolution within polymeric scaffolds, drawing comparisons to the behaviour observed in natural bone. Additionally, the effect of polymer microstructure, incorporating reinforcing materials, the introduction of topological features, and hydrodynamic/corrosive impact of body fluids in the fatigue life of scaffolds are discussed. Understanding these parameters is crucial for enhancing the fatigue resistance of polymeric scaffolds and holds promise for expanding their application in clinical settings as structural biomaterials. STATEMENT OF SIGNIFICANCE: Polymers have promising advantages for bone tissue engineering, including adjustable degradation rates, compatibility with native bone stiffness, ease of fabrication, and low toxicity. However, their limited mechanical strength has hindered their use in load-bearing scaffolds for clinical applications. While prior studies have addressed static behaviour of polymeric scaffolds, a comprehensive review of their fatigue performance is lacking. This review explores this gap, addressing fatigue characteristics, failure mechanisms, and the influence of parameters like material properties, topological features, loading conditions, and environmental factors. It also examines microstructure, reinforcement materials, pore architectures, body fluids, and tissue ingrowth effects on fatigue behaviour. A significant emphasis is placed on understanding fatigue damage progression in polymeric scaffolds, comparing it to natural bone behaviour.

Optimization and manufacture of polyetheretherketone patient specific cranial implants by material extrusion - A clinical perspective

Polyetheretherketone (PEEK) is a high performing thermoplastic that has established itself as a 'gold-standard' material for cranial reconstruction. Traditionally, milled PEEK patient specific cranial implants (PSCIs) exhibit uniform levels of smoothness (excusing suture/drainage holes) to the touch (<1 μm) and homogenous coloration throughout. They also demonstrate predictable and repeatable levels of mechanical performance, as they are machined from isotropic material blocks. The combination of such factors inspires confidence from the surgeon and in turn, approval for implantation. However, manufacturing lead-times and affiliated costs to fabricate a PSCI are high. To simplify their production and reduce expenditure, hospitals are exploring the production of in-house PEEK PSCIs by material extrusion-based additive manufacturing. From a geometrical and morphological perspective, such implants have been produced with good-to-satisfactory clinical results. However, lack of clinical adoption persists. To determine the reasoning behind this, it was necessary to assess the benefits and limitations of current printed PEEK PSCIs in order to establish the status quo. Afterwards, a review on individual PEEK printing variables was performed in order to identify a combination of parameters that could enhance the aesthetics and performance of the PSCIs to that of milled implants/cranial bone. The findings from this review could be used as a baseline to help standardize the production of PEEK PSCIs by material extrusion in the hospital.

3D printed TPMS structural PLA/GO scaffold: Process parameter optimization, porous structure, mechanical and biological properties

Bone scaffolds should have good biocompatibility and mechanical and biological properties, which are primarily by the material design, porous structure, and preparation process. In this study, we proposed polylactic acid (PLA) as the base material, graphene oxide (GO) as an enhancing filler, triply periodic minimal surface (TPMS) as a porous structure, and fused deposition modeling (FDM) 3D printing as a preparation technology to develop a TPMS structural PLA/GO scaffold and evaluate their porous structures, mechanical properties, and biological properties towards bone tissue engineering. Firstly, the influence of the FDM 3D printing process parameters on the forming quality and mechanical properties of PLA was studied by orthogonal experimental design, based on which the process parameters were optimized. Then, GO was composited with PLA, and PLA/GO nanocomposites were prepared by FDM. The mechanical tests showed that GO can effectively improve the tensile and compression strength of PLA; only by adding 0.1% GO the tensile and compression modulus was increased by 35.6% and 35.8%, respectively. Then, TPMS structural (Schwarz-P, Gyroid) scaffold models were designed and TPMS structural PLA/0.1%GO nanocomposite scaffolds were prepared by FDM. The compression test showed that the TPMS structural scaffolds had higher compression strength than the Grid structure; This was owing to the fact that the continuous curved structure of TMPS alleviated stress concentration and had a more uniform stress bearing. Moreover, cell culture indicated bone marrow stromal cells (BMSCs) showed better adhesion, proliferation, and osteogenic differentiation behaviors on the TPMS structural scaffolds as the continuous surface structure of TPMS had better connectivity and larger specific surface area. These results suggest that the TPMS structural PLA/GO scaffold has potential application in bone repair. This article suggests the feasibility of co-designing the material, structure, and technology for achieving the good comprehensive performance of polymer bone scaffolds.

A novel bioactive glass/graphene oxide composite coating for a polyether ether ketone-based dental implant

Polyether ether ketone (PEEK) is a biocompatible material that lacks antimicrobial activity and bioactivity; therefore, is not appropriate for use as a dental implant. To overcome these deficiencies, a novel composite coating of bioactive glass and graphene oxide was prepared. PEEK discs were polished, cleaned, and the surface treated with sulfuric acid for 15 min. The composite coating consisted of bioactive glass produced by the sol-gel route and doped with 0.75 wt% graphene oxide. X-ray diffraction, Fourier transform infrared spectroscopy, and scanning electron microscopy-energy dispersive spectroscopy analyses were employed to characterize the composite coating, and the coating adhesion strength quantified using a pull-off test. Cytotoxicity was assessed using osteoblast-like cells and gingival fibroblasts. The wettability of the coated and non-coated samples was determined by optical contact angle assessment, and bioactivity was assessed by immersion in simulated body fluid. The results revealed that the bioactive glass/graphene oxide composite coating, approximately 7 μm thick, was transparent, homogenous with few microcracks and microporosities, but adhered strongly and was not cytotoxic to either osteoblast-like cells or gingival fibroblasts. The wettability of the PEEK sample was increased to <20° after coating with the composite, and apatite formation was detectable after 14 days of immersion in simulated body fluid.

Fabrication of bFGF/polydopamine-loaded PEEK implants for improving soft tissue integration by upregulating Wnt/β-catenin signaling

The difficulties associated with polyetheretherketone (PEEK) implants and soft tissue integration for craniomaxillofacial bone repair have led to a series of complications that limit the clinical benefits. In this study, 3D printed multi-stage microporous PEEK implants coated with bFGF via polydopamine were fabricated to enhance PEEK implant-soft tissue integration. Multistage microporous PEEK scaffolds prepared by sulfonation of concentrated sulfuric acid were coated with polydopamine, and then used as templates for electrophoretic deposition of bFGF bioactive factors. Achieving polydopamine and bFGF sustained release, the composite PEEK scaffolds possessed good mechanical properties, hydrophilicity, protein adhesion properties. The in vitro results indicated that bFGF/polydopamine-loaded PEEK exhibited good biocompatibility to rabbit embryonic fibroblasts (REF) by promoting cell proliferation, adhesion, and migration. Ribonucleic acid sequencing (RNA-seq) revealed that bFGF/polydopamine-loaded PEEK implants significantly upregulated the expression of genes and proteins associated with soft tissue integration and activated Wnt/β-catenin signaling in biological processes, but related expression of genes and proteins was significantly downregulated when the Wnt/β-catenin signaling was inhibited. Furthermore, in vivo bFGF/polydopamine-loaded PEEK implants exhibited excellent performance in improving the growth and adhesion of the surrounding soft tissue. In summary, bFGF/polydopamine-loaded PEEK implants possess soft tissue integration properties by activating the Wnt/β-catenin signaling, which have a potential translational clinical application in the future.

Biomechanical and osteointegration study of 3D-printed porous PEEK hydroxyapatite-coated scaffolds

The objective of this study as to evaluate the biomechanical and osteointegration properties of 3D printed porous polyetheretherketone (PEEK) with hydroxyapatite (HA) coating by simulated body fluid (SBF) method. Cylindrical scaffolds were designed and fabricated by using PEEK material through fused deposition molding (FDM). The scaffolds were divided into solid group, porous group and porous-HA group (decorated by hydroxyapatite). The mechanical properties of each group of scaffolds were tested. Then, a total of 12 New Zealand rabbits were implemented for implantation of scaffolds at femoral condyle. Finally, the osteointegration ability of scaffolds were evaluated by Micro computed tomography (Micro-CT), histology and fluorescence staining. The HA was successfully decorated on the surface of the PEEK scaffold. The modulus of solid, porous and porous-HA group was 1289.43 ± 71.44 MPa, 196.36 ± 9.89 MPa and 183.29 ± 7.71 MPa, and the compressive strength was 107.24 ± 5.15 MPa, 33.12 ± 3.86 MPa and 29.99 ± 4.16 MPa, respectively. The micro-CT results showed that the bone volume/total volume ratio (BV/TV) in the porous-HA group was significantly greater than that in solid and porous group. Compared with porous group, the trabecular number (Tb. N) and trabecular thickness (Tb. Th) of porous-HA group was higher, and the trabecular spacing (Tb. Sp) was lower. The histology and fluorescence staining showed that more new bone tissue was formed in the porous-HA at different periods compared with the porous and solid groups. In addition, according to the results of the biomechanical test and osteointegration assessment, the biomechanical properties of 3D-printed porous PEEK scaffolds are close to human trabecular bone tissue, and the hydroxyapatite coating does not degrade its biomechanical performance. The porous structure can facilitate the integration of bone tissue, and the HA coating can markedly improve this process.

Impact of surface roughness and bulk porosity on spinal interbody implants

Spinal fusion surgeries are performed to treat a multitude of cervical and lumbar diseases that lead to pain and disability. Spinal interbody fusion involves inserting a cage between the spinal vertebrae, and is often utilized for indirect neurologic decompression, correction of spinal alignment, anterior column stability, and increased fusion rate. The long-term success of interbody fusion relies on complete osseointegration between the implant surface and vertebral end plates. Titanium (Ti)-based alloys and polyetheretherketone (PEEK) interbody cages represent the most commonly utilized materials and provide sufficient mechanics and biocompatibility to assist in fusion. However, modification to the surface and bulk characteristics of these materials has been shown to maximize osseointegration and long-term stability. Specifically, the introduction of intrinsic porosity and surface roughness has been shown to affect spinal interbody mechanics, vascularization, osteoblast attachment, and ingrowth potential. This narrative review synthesizes the mechanical, in vitro, in vivo, and clinical effects on fusion efficacy associated with introduction of porosity in Ti (neat and alloy) and PEEK intervertebral implants.

Mechanical performance and bioactivation of 3D-printed PEEK for high-performance implant manufacture: a review

Polyetheretherketone (PEEK) has stood out as the leading high-performance thermoplastic for the replacement of metals in orthopaedic, trauma and spinal implant applications due to its high biocompatibility and mechanical properties. Despite its potential for custom-made medical devices, 3D-printed PEEK's mechanical performance depends on processing parameters and its bioinertness may hinder bone opposition to the implant. Concerning these challenges, this review focuses on the available literature addressing the improvement of the mechanical performance of PEEK processed through "fused filament fabrication" (FFF) along with literature on bioactivation of PEEK for improved osseointegration. The reviewed research suggests that improvements can be achieved in mechanical performance of 3D-printed PEEK with adequate FFF parametrization while different bioactivation techniques can be used to improve the bioperformance of 3D-printed PEEK. The adequate approaches towards these procedures can increase PEEK's potential for the manufacture of high-performance custom-made implantable devices that display improved bone-implant integration and prevent stress shielding of the treated bone.

Mechanical behavior of 3D-printed PEEK and its application for personalized orbital implants with various infill patterns and densities

This study proposed a 3D-printed PEEK with a specific design to restore the damaged orbit shape. Such printed personalized implants are greatly affected by the process parameters, wherefore the effects of the nozzle temperatures, printing speed and layer thickness on the tensile properties were investigated based on the Taguchi approach. The optimal mechanical properties, i.e., the tensile strength and Young's modulus, were found to be 54.97 MPa and 2.67 GPa, respectively. These properties were obtained by adjusting the nozzle temperature to its high level (450 °C), while the layer thickness (0.1 mm) and printing speed (20 mm/s) were set to their low levels. Secondly, the mechanical behavior of a personalized orbital implant with these optimized properties was evaluated via finite elements analysis with various infill patterns and densities, at three thicknesses: 0.3, 0.5 and 0.7 mm. It was found that all thicknesses were acceptable for the 100% filling. For the honeycomb pattern, the thicknesses 0.5 and 0.7 mm were satisfactory with a fill rate of 70% and 55% whereas only the thickness of 0.7 mm was suitable for the 40% filling. The honeycomb pattern with 40% filling and a maximum stress (7.186 MPa) and strain (0.00627 mm) should be beneficial for light-weight orbital implants.

PCL strut-like scaffolds appear superior to gyroid in terms of bone regeneration within a long bone large defect: An in silico study

The treatment of large bone defects represents a major clinical challenge. 3D printed scaffolds appear as a promising strategy to support bone defect regeneration. The 3D design of such scaffolds impacts the healing path and thus defect regeneration potential. Among others, scaffold architecture has been shown to influence the healing outcome. Gyroid architecture, characterized by a zero mean surface curvature, has been discussed as a promising scaffold design for bone regeneration. However, whether gyroid scaffolds are favourable for bone regeneration in large bone defects over traditional strut-like architecture scaffolds remains unknown. Therefore, the aim of this study was to investigate whether gyroid scaffolds present advantages over more traditional strut-like scaffolds in terms of their bone regeneration potential. Validated bone defect regeneration principles were applied in an in silico modeling approach that allows to predict bone formation in defect regeneration. Towards this aim, the mechano-biological bone regeneration principles were adapted to allow simulating bone regeneration within both gyroid and strut-like scaffolds. We found that the large surface curvatures of the gyroid scaffold led to a slower tissue formation dynamic and conclusively reduced bone regeneration. The initial claim, that an overall reduced zero mean surface curvature would enhance bone formation, could not be confirmed. The here presented approach illustrates the potential of in silico tools to evaluate in pre-clinical studies scaffold designs and eventually lead to optimized architectures of 3D printed implants for bone regeneration.

Development of an architecture-property model for triply periodic minimal surface structures and validation using material extrusion additive manufacturing with polyetheretherketone (PEEK)

Additively manufactured structures designed from triply periodic minimal surfaces (TPMSs) have been receiving attention for their potential uses in the medical, aerospace, and automobile industries. Understanding how these complex geometries can be designed to achieve particular architectural and mechanical properties is essential for tuning their function to certain applications. In this study, we created design tools for visualizing the interplay between TPMS design parameters and resulting architecture and aimed to validate a model of the relationship between structure architecture and Young's modulus. A custom MATLAB script was written to analyze structural properties for families of Schoen gyroid and Schwarz diamond structures, and a numerical homogenization scheme was performed to predict the effective Young's moduli of the structures based on their architecture. Our modeling methods were validated experimentally with polyetheretherketone (PEEK) structures created using material extrusion additive manufacturing. The architectural characteristics of the structures were determined using micro-computed tomography, and compression testing was performed to determine yield strength and Young's modulus. Two different initial build orientations were tested to determine the behavior both perpendicular and parallel to the layer deposition direction (referred to as z-direction and xy-direction, respectively). The z-direction Young's modulus ranged from 289.7 to 557.5 MPa and yield strength ranged from 10.12 to 20.3 MPa. For the xy-direction, Young's modulus ranged from 133.8 to 416.4 MPa and yield strength ranged from 3.8 to 12.2 MPa. For each initial build orientation, the mechanical properties were found to decrease with increasing porosity, and failure occurred due to both strut bending and interlayer debonding. The mechanical properties predicted by the modeling agreed with the values found for z-direction samples (difference 2-11%) but less so for xy-direction samples (difference 27-62%) due to weak interlayer bonding and print path irregularities. Ultimately, the findings presented here provide better understanding of the range of properties achievable for additive manufacturing of PEEK and encouraging results for a TPMS architecture-property model.

Additive Manufacturing: An Opportunity for the Fabrication of Near-Net-Shape NiTi Implants

Nickel–titanium (NiTi) is a shape-memory alloy, a type of material whose name is derived from its ability to recover its original shape upon heating to a certain temperature. NiTi falls under the umbrella of metallic materials, offering high superelasticity, acceptable corrosion resistance, a relatively low elastic modulus, and desirable biocompatibility. There are several challenges regarding the processing and machinability of NiTi, originating from its high ductility and reactivity. Additive manufacturing (AM), commonly known as 3D printing, is a promising candidate for solving problems in the fabrication of near-net-shape NiTi biomaterials with controlled porosity. Powder-bed fusion and directed energy deposition are AM approaches employed to produce synthetic NiTi implants. A short summary of the principles and the pros and cons of these approaches is provided. The influence of the operating parameters, which can change the microstructural features, including the porosity content and orientation of the crystals, on the mechanical properties is addressed. Surface-modification techniques are recommended for suppressing the Ni ion leaching from the surface of AM-fabricated NiTi, which is a technical challenge faced by the long-term in vivo application of NiTi.

Lattice implants that generate homeostatic and remodeling strains in bone

Bone remodeling is mediated by several factors including strain. An increase in strain between 1% and 10% compared to homeostasis can trigger bone formation. We aim to create an orthopedic implant using clinically established imaging and manufacturing methods that induces this strain control in human bone. Titanium scaffolds were manufactured with multiaxial apparent modulus tailored to the mechanical properties of bone defined from computed tomography scans of cadaver human tibiae. Five bone cubes were tested with corresponding titanium scaffolds by loading under compression, which is similar to the implanted tibia loading condition. Bone strain was precisely controlled by varying the scaffold modulus, from 0% to 15% bone strain increase. This strain increase is the magnitude reported to invoke bone's positive remodeling. Axial modulus was closely matched between titanium scaffolds and bone, ranging from 48-728 and 81-800 MPa, respectively, whereby scaffold axial modulus was within 2% of nominal target values. Fine control of multiaxial moduli resulted in transverse modulus that matched bone well; ranging from 42-648 and 47-585 MPa in scaffolds and bone respectively. The scaffold manufacturing material and method are already used in the orthopedic industry. This study has significant clinical implications as it enables the design of implants which positively harness bone's natural mechanoresponse and respect bone's mechanical anisotropy and heterogeneity.

Modification of polyetheretherketone (PEEK) physical features to improve osteointegration

Polyetheretherketone (PEEK) has been widely applied in orthopedics because of its excellent mechanical properties, radiolucency, and biocompatibility. However, the bioinertness and poor osteointegration of PEEK have greatly limited its further application. Growing evidence proves that physical factors of implants, including their architecture, surface morphology, stiffness, and mechanical stimulation, matter as much as the composition of their surface chemistry. This review focuses on the multiple strategies for the physical modification of PEEK implants through adjusting their architecture, surface morphology, and stiffness. Many research findings show that transforming the architecture and incorporating reinforcing fillers into PEEK can affect both its mechanical strength and cellular responses. Modified PEEK surfaces at the macro scale and micro/nano scale have positive effects on cell-substrate interactions. More investigations are necessary to reach consensus on the optimal design of PEEK implants and to explore the efficiency of various functional implant surfaces. Soft-tissue integration has been ignored, though evidence shows that physical modifications also improve the adhesion of soft tissue. In the future, ideal PEEK implants should have a desirable topological structure with better surface hydrophilicity and optimum surface chemistry.

3D printed porous sulfonated polyetheretherketone scaffold for cartilage repair: Potential and limitation

Objective

The treatment of cartilage lesions has always been a difficult problem. Although cartilage tissue engineering provides alternative treatment options for cartilage lesions, biodegradable tissue engineering scaffolds have limitations.

Methods

In this study, we constructed a porous PEEK scaffold via 3D printing, surface-engineered with concentrated sulfuric acid for 15 s (SPK-15), 30 s (SPK-30), and 60 s (SPK-60). We systematically evaluated the physical and chemical characteristics and biofunctionalities of the scaffolds, and then evaluated the macrophage polarization modulating ability and anti-inflammatory effects of the sulfonated PEEK, and observed the cartilage-protective effect of SPK using a co-culture study. We further evaluated the repair effect of PEEK and SPK by implanting the prosthetic scaffold into a cartilage defect in a rabbit model.

Results

Compared to the PEEK, SPK-15 and SPK-60 scaffolds, SPK-30 has a good micro/nanostructure, appropriate biomechanical properties (compressive modulus, 43 ± 5 MPa; Shaw hardness, 20.6 ± 1.3 HD; close to native cartilage, 30 ± 8 MPa, 17.8 ± 0.8 HD), and superior biofunctionalities. Compared to PEEK, sulfonated PEEK can favor macrophage polarization to the M2 phenotype, which increases anti-inflammatory cytokine secretion. Furthermore, SPK can also prevent macrophage-induced cartilage degeneration. The in-vivo animal experiment demonstrates that SPK can favor new tissue ingrowth and integration, prevent peri-scaffold cartilage degeneration and patellar cartilage degeneration, inhibit inflammatory cytokine secretion, and promote cartilage function restoration.

Conclusion

The present study confirmed that the 3D printed porous sulfonated PEEK scaffold could promote cartilage functional repair, and suggests a new promising strategy for treating cartilage defects with a functional prosthesis that spontaneously inhibits nearby cartilage degeneration.

Translational potential of this article

In the present study, we propose a new cartilage repair strategy based on a porous, non-biodegradable polyetheretherketone (PEEK) scaffold, which may bring up a new treatment route for elderly patients with cartilage lesions in the future.

Total and partial knee arthroplasty implants that maintain native load transfer in the tibia

AIMS

Unicompartmental and total knee arthroplasty (UKA and TKA) are successful treatments for osteoarthritis, but the solid metal implants disrupt the natural distribution of stress and strain which can lead to bone loss over time. This generates problems if the implant needs to be revised. This study investigates whether titanium lattice UKA and TKA implants can maintain natural load transfer in the proximal tibia.

METHODS

In a cadaveric model, UKA and TKA procedures were performed on eight fresh-frozen knee specimens, using conventional (solid) and titanium lattice tibial implants. Stress at the bone-implant interfaces were measured and compared to the native knee.

RESULTS

Titanium lattice implants were able to restore the mechanical environment of the native tibia for both UKA and TKA designs. Maximum stress at the bone-implant interface ranged from 1.2 MPa to 3.3 MPa compared with 1.3 MPa to 2.7 MPa for the native tibia. The conventional solid UKA and TKA implants reduced the maximum stress in the bone by a factor of 10 and caused > 70% of bone surface area to be underloaded compared to the native tibia.

CONCLUSION

Titanium lattice implants maintained the natural mechanical loading in the proximal tibia after UKA and TKA, but conventional solid implants did not. This is an exciting first step towards implants that maintain bone health, but such implants also have to meet fatigue and micromotion criteria to be clinically viable. Cite this article: Bone Joint Res 2022;11(2):91-101.

Emulsion templated scaffolds of poly(ε-caprolactone) - a review

The role of poly(ε-caprolactone) (PCL) and its 3D scaffolds in tissue engineering has already been established due to its ease of processing into long-term degradable implants and approval from the FDA. This review presents the role of high internal phase emulsion (HIPE) templating in the fabrication of PCL scaffolds, and the versatility of the technique along with challenges associated with it. Considering the huge potential of HIPE templating, which so far has mainly been focused on free radical polymerization of aqueous HIPEs, we provide a summary of how the technique has been expanded to non-aqueous HIPEs and other modes of polymerization such as ring-opening. The scope of coupling of HIPE templating with some of the advanced fabrication methods such as 3D printing or electrospinning is also explored.

Comprehensive Review on Design and Manufacturing of Bio-scaffolds for Bone Reconstruction

Bio-scaffolds are synthetic entities widely employed in bone and soft-tissue regeneration applications. These bio-scaffolds are applied to the defect site to provide support and favor cell attachment and growth, thereby enhancing the regeneration of the defective site. The progressive research in bio-scaffold fabrication has led to identification of biocompatible and mechanically stable materials. The difficulties in obtaining grafts and expenditure incurred in the transplantation procedures have also been overcome by the implantation of bio-scaffolds. Drugs, cells, growth factors, and biomolecules can be embedded with bio-scaffolds to provide localized treatments. The right choice of materials and fabrication approaches can help in developing bio-scaffolds with required properties. This review mostly focuses on the available materials and bio-scaffold techniques for bone and soft-tissue regeneration application. The first part of this review gives insight into the various classes of biomaterials involved in bio-scaffold fabrication followed by design and simulation techniques. The latter discusses the various additive, subtractive, hybrid, and other improved techniques involved in the development of bio-scaffolds for bone regeneration applications. Techniques involving multimaterial printing and multidimensional printing have also been briefly discussed.

Evaluation of a self-fitting, shape memory polymer scaffold in a rabbit calvarial defect model

Self-fitting scaffolds prepared from biodegradable poly(ε-caprolactone)-diacrylate (PCL-DA) have been developed for the treatment of craniomaxillofacial (CMF) bone defects. As a thermoresponsive shape memory polymer (SMP), with the mere exposure to warm saline, these porous scaffolds achieve a conformal fit in defects. This behavior was expected to be advantageous to osseointegration and thus bone healing. Herein, for an initial assessment of their regenerative potential, a pilot in vivo study was performed using a rabbit calvarial defect model. Exogenous growth factors and cells were excluded from the scaffolds. Key scaffold material properties were confirmed to be maintained following gamma sterilization. To assess scaffold integration and neotissue infiltration along the defect perimeter, non-critically sized (d = 8 mm) bilateral calvarial defects were created in 12 New Zealand white rabbits. Bone formation was assessed at 4 and 16 weeks using histological analysis and micro-CT, comparing defects treated with an SMP scaffold (d = 9 mm x t = 1 or 2 mm) to untreated defects (i.e. defects able to heal without intervention). To further assess osseointegration, push-out tests were performed at 16 weeks and compared to defects treated with poly(ether ether ketone) (PEEK) discs (d = 8.5 mm x t = 2 mm). The results of this study confirmed that the SMP scaffolds were biocompatible and highly conducive to bone formation and ingrowth at the perimeter. Ultimately, this resulted in similar bone volume and surface area versus untreated defects and superior performance in push-out testing versus defects treated with PEEK discs. STATEMENT OF SIGNIFICANCE: Current treatments of craniomaxillofacial (CMF) bone defects include biologic and synthetic grafts but they are limited in their ability to form good contact with adjacent tissue. A regenerative engineering approach using a biologic-free scaffold able to achieve conformal fitting represents a potential "off-the-shelf" surgical product to heal CMF bone defects. Having not yet been evaluated in vivo, this study provided the preliminary assessment of the bone healing potential of self-fitting PCL scaffolds using a rabbit calvarial defect model. The study was designed to assess scaffold biocompatibility as well as bone formation and ingrowth using histology, micro-CT, and biomechanical push-out tests. The favorable results provide a basis to pursue establishing self-fitting scaffolds as a treatment option for CMF defects.

The Surface Characterisation of Fused Filament Fabricated (FFF) 3D Printed PEEK/Hydroxyapatite Composites

Polyetheretherketone (PEEK) is a high-performance thermoplastic polymer which has found increasing application in orthopaedics and has shown a lot of promise for 'made-to-measure' implants via additive manufacturing approaches. However, PEEK is bioinert and needs to undergo surface modification to make it at least osteoconductive to ensure a more rapid, improved, and stable fixation that will last longer in vivo. One approach to solving this issue is to modify PEEK with bioactive agents such as hydroxyapatite (HA). The work reported in this study demonstrates the direct 3D printing of PEEK/HA composites of up to 30 weight percent (wt%) HA using a Fused Filament Fabrication (FFF) approach. The surface characteristics and in vitro properties of the composite materials were investigated. X-ray diffraction revealed the samples to be semi-crystalline in nature, with X-ray Photoelectron Spectroscopy and Time-of-Flight Secondary Ion Mass Spectrometry revealing HA materials were available in the uppermost surface of all the 3D printed samples. In vitro testing of the samples at 7 days demonstrated that the PEEK/HA composite surfaces supported the adherence and growth of viable U-2 OS osteoblast like cells. These results demonstrate that FFF can deliver bioactive HA on the surface of PEEK bio-composites in a one-step 3D printing process.

Additively-manufactured PEEK/HA porous scaffolds with highly-controllable mechanical properties and excellent biocompatibility

Polyetheretherketone (PEEK) was widely applied into fabricating of orthopaedic implants, benefitting its excellent biocompatibility and similar mechanical properties to native bones. However, the inertness of PEEK hinders its integration with the surrounding bone tissue. Here PEEK scaffolds with a series of hydroxyapatite (HA) contents in gradient were manufactured via fused filament fabrication (FFF) 3D printing techniques. The influence of the pore size, HA content and printing direction on the mechanical properties of the PEEK/HA scaffolds was systematically evaluated. By adjusting the pore size and HA contents, the elastic modulus of the PEEK/HA scaffolds can be widely tuned in the range of 624.7-50.6 MPa, similar to the variation range of natural cancellous bone. Meanwhile, the scaffolds exhibited higher Young's modulus and lower compressive strength along Z printing direction. The mapping relationship among geometric parameters, HA content, printing direction and mechanical properties was established, which gave more accurate predictions and controllability of the modulus and strength of scaffolds. The PEEK/HA scaffolds with the micro-structured surface could promote cell attachment and mineralization in vitro. Therefore, the FFF-printed PEEK/HA composites scaffolds can be a good candidate for bone grafting and tissue engineering.

A Multi-Criteria Assessment Strategy for 3D Printed Porous Polyetheretherketone (PEEK) Patient-Specific Implants for Orbital Wall Reconstruction

Pure orbital blowout fractures occur within the confines of the internal orbital wall. Restoration of orbital form and volume is paramount to prevent functional and esthetic impairment. The anatomical peculiarity of the orbit has encouraged surgeons to develop implants with customized features to restore its architecture. This has resulted in worldwide clinical demand for patient-specific implants (PSIs) designed to fit precisely in the patient's unique anatomy. Material extrusion or Fused filament fabrication (FFF) three-dimensional (3D) printing technology has enabled the fabrication of implant-grade polymers such as Polyetheretherketone (PEEK), paving the way for a more sophisticated generation of biomaterials. This study evaluates the FFF 3D printed PEEK orbital mesh customized implants with a metric considering the relevant design, biomechanical, and morphological parameters. The performance of the implants is studied as a function of varying thicknesses and porous design constructs through a finite element (FE) based computational model and a decision matrix based statistical approach. The maximum stress values achieved in our results predict the high durability of the implants, and the maximum deformation values were under one-tenth of a millimeter (mm) domain in all the implant profile configurations. The circular patterned implant (0.9 mm) had the best performance score. The study demonstrates that compounding multi-design computational analysis with 3D printing can be beneficial for the optimal restoration of the orbital floor.

The Treatment Strategy for Skull Base Reconstruction for Anterior Cranial Fossa Intra- and Extracranial Tumors

ABSTRACT

Anterior cranial fossa intra- and extracranial tumors arise from the anterior cranial fossa and invade the orbit and nose. Anterior cranial fossa tumor resection and skull base reconstruction are challenging for neurosurgeons due to the complex anatomy, leakage of cerebrospinal fluid, and critical neurovasculature involvement. The authors report a case series of cranio-orbital communicating tumors and cranionasal-orbital communicating tumors. All patients underwent a modified Derome approach or transfrontal basal approach, and all tumor resections were satisfactory. Skull base reconstruction for small defects (<1.5 cm) can be performed with autogenous fascia, muscle, and fat. Large defects (≥1.5 cm) require autogenous fascia, muscle, and fat combined with osseous reconstruction (autogenous bone, titanium mesh, and polyetheretherketone). The techniques and treatments were successful, and only 1 patient experienced mild cerebrospinal fluid leak but no intracranial infection, pneumocrania or intracranial hemorrhage. Additionally, long-term follow-up demonstrated that the outcomes remain favorable. According to a literature review, this technique might be an alternative strategy for treating anterior cranial fossa intra- and extracranial tumors, and better skull base reconstruction can prevent many postoperative complications.

Modification of polyetheretherketone implants: From enhancing bone integration to enabling multi-modal therapeutics

Polyetheretherketone (PEEK) is a popular thermoplastic material widely used in engineering applications due to its favorable mechanical properties and stability at high temperatures. With the first implantable grade PEEK being commercialized in 1990s, the use of PEEK has since grown exponentially in the biomedical field and has rapidly transformed a large section of the medical devices landscape. Nowadays, PEEK is a standard biomaterial used across a wide range of implant applications, however, its bioinertness remains a limitation for bone repair applications. The increasing demand for enhanced treatment efficacy/improved patient quality of life, calls for next-generation implants that can offer fast bone integration as well as other desirable therapeutic functions. As such, modification of PEEK implants has progressively shifted from offering desirable mechanical properties, enhancing bioactivity/fast osteointegration, to more recently, tackling post-surgery bacterial infection/biofilm formation, modulation of inflammation and management of bone cancers. Such progress is also accompanied by the evolution of the PEEK manufacturing technologies, to meet the ever increasing demand for more patient specific devices. However, no review has comprehensively covered the recently engaged application areas to date. This paper provides an up-to-date review on the development of PEEK-based biomedical devices in the past 10 years, with particularly focus on modifying PEEK for multi-modal therapeutics. The aim is to provide the peers with a timely update, which may guide and inspire the research and development of next generation PEEK-based healthcare products. STATEMENT OF SIGNIFICANCE: Significant progress has been made in PEEK processing and modification techniques in the past decades, which greatly contributed to its wide applications in the biomedical field. Despite the high volume of published literature on PEEK implant related research, there is a lack of review on its emerging applications in multi-modal therapeutics, which involve bone regeneration, anti-bacteria/anti-inflammation, and cancer inhibition, etc. This timely review covers the state-of-the-art in these exciting areas and provides the important guidance for next generation PEEK based biomedical device research and development.

Strength and elastic properties of 3D printed PVDF-based parts for lightweight biomedical applications

Research results on 3D printed fluoropolymers are scarce since the filaments were introduced commercially only in the last several years to enable fused filament fabrication (FFF) of structural components for more demanding service conditions, where chemical, UV or fire resistance, high purity, sterilizability or biocompatibility are critical such as in biomedical industry. This experimental study reports on additive manufacturing and quasi-static mechanical testing of polyvinylidene fluoride (PVDF) and in-vitro cytocompatible polyvinylidene fluoride-co-hexafluoropropylene (PVDF-HFP) specimens that were 3D printed with different infill patterns at 75% density (linear, cubic, cross, concentric, octet, zigzag, triangular). Recommendations are provided for addressing issues related to weak adhesion and obtrusive warping, which occur in open-chamber FFF printer due to semi-crystalline and hydrophobic nature of PVDF-based thermoplastics. The measured tensile and flexural stress-strain curves are analyzed to determine the influence of strut-based infills on the strength and elastic performance by including comparisons in ratios between strength, modulus of elasticity and weight of the specimens. The concentric pattern demonstrates the highest tensile strength, while the cross and triangular lattices - the lowest one. In three-point bending, the linear pattern delivers the lowest strength, while the rest exhibit comparable mechanical properties. The results are conducive to the design of 3D printable PVDF homopolymer and copolymer load-bearing structures serving as lightweight high-performance components in biomedical applications.

Surface porous poly-ether-ether-ketone based on three-dimensional printing for load-bearing orthopedic implant

Poly-ether-ether-ketone (PEEK) possesses excellent biocompatibility and similar elastic modulus as bones but yet suffers from poor osseointegration. In order to balance PEEK's mechanical and osseointegration properties, a novel surface porous PEEK (SP-PEEK) is successfully fabricated by fused deposition modelling three-dimensional printing (FDM 3DP) and characterized by mechanical and osteogenesis in vitro tests. Moreover, the effects of pore diameter and pore layer number on the mechanical behaviors of SP-PEEK are investigated by theoretical model and numerical simulation. Comparison among experimental, theoretical and simulation results show good agreement. As pore diameter decreases, the equivalent strength and modulus become more sensitive to the decrease of pore layer number. In addition, the SP-PEEK exhibits the mechanical properties within the range of human trabecular bone and cortical bone, and thus can be tailored to mimic human bone by adjusting the pore diameter and pore layer number, which is benefit to mitigate stress shielding. The effects of pore diameter on the cell proliferation and osteogenic differentiation of SP-PEEK are tested by the co-culture of osteoblast precursor cells (MC3T3-E1) and SP-PEEK round discs. Results showcase that porous surface improves the osteogenesis in vitro, and the SP-PEEK group that the pore diameter is 0.6 mm exhibits optimal-performance osteogenesis in vitro.

Structure, properties, and bioactivity of 3D printed PAEKs for implant applications: A systematic review

Additive manufacturing (AM) of high temperature polymers, specifically polyaryletherketones (PAEK), is gaining significant attention for medical implant applications. As 3D printing systems evolve toward point of care manufacturing, research on this topic continues to expand. Specific regulatory guidance is being developed for the safe management of 3D printing systems in a hospital environment. PAEK implants can benefit from many advantages of AM such as design freedom, material and antibacterial drug incorporation, and enhanced bioactivity provided by cancellous bone-like porous designs. In addition to AM PAEK bioactivity, the biomechanical strength of 3D printed implants is crucial to their performance and thus widely studied. In this review, we discuss the printing conditions that have been investigated so far for additively manufactured PAEK implant applications. The effect of processing parameters on the biomechanical strength of implants is summarized, and the bioactivity of PAEKs, along with material and drug incorporation, is also covered in detail. Finally, the therapeutic areas in which 3D printed PAEK implants are investigated and utilized are reviewed.

Effects of printing path and material components on mechanical properties of 3D-printed polyether-ether-ketone/hydroxyapatite composites

Polyether-ether-ketone (PEEK) exhibits excellent mechanical properties and biocompatibility. Three-dimensional (3D) printing of PEEK bone substitutes has been widely used in clinical application. However, the inertness of pure PEEK hinders its integration with the surrounding bone tissue. In this study, for the first time, PEEK/hydroxyapatite (HA) composite specimens were fabricated using fused filament fabrication (FFF) technology. PEEK/HA filaments with HA contents of 0-30 wt% were fabricated via mechanical mixing and extrusion. The HA distributions inside the composite matrix and the surface morphology characteristics of the PEEK/HA composites were examined. The effects of the printing path and HA content on the mechanics of the PEEK/HA composites were systematically investigated. The results indicated that the HA particles were uniformly distributed on the composite matrix. With an increase in the HA content, the modulus of the PEEK/HA composite increased, while the strength and failure strain concomitantly decreased. When the HA content increased to 30 wt%, the tensile modulus of the composite increased by 68.6% compared with that of pure PEEK printed along the horizontal 90° path, while the tensile strength decreased by 48.2% compared with that of pure PEEK printed along the vertical 90° path. The fracture elongation of the printed specimens with different HA contents decreased in the following order: horizontal 0° > horizontal 90° > vertical 90°. The best comprehensive mechanical properties were achieved for pure PEEK fabricated along the horizontal 0° path. The results indicate that FFF technology is applicable for additive manufacturing of PEEK/HA composites with controllable compositions. Printed PEEK/HA composites have potential for applications in the design and manufacturing of personalized bone substitutes.

Additive-Manufactured Gyroid Scaffolds of Magnesium Oxide, Phosphate Glass Fiber and Polylactic Acid Composite for Bone Tissue Engineering

Composites of biodegradable phosphate glass fiber and polylactic acid (PGF/PLA) show potential for bone tissue engineering scaffolds, due to their ability to release Ca, P, and Mg during degradation, thus promoting the bone repair. Nevertheless, glass degradation tends to acidify the surrounding aqueous environment, which may adversely affect the viability and bone-forming activities of osteoblasts. In this work, MgO was investigated as a neutralizing agent. Porous network-phase gyroid scaffolds were additive-manufactured using four different materials: PLA, MgO/PLA, PGF/PLA, and (MgO + PGF)/PLA. The addition of PGF enhanced compressive properties of scaffolds, and the resultant scaffolds were comparably strong and stiff with human trabecular bone. While the degradation of PGF/PLA composite induced considerable acidity in degradation media and intensified the degradation of PGF in return, the degradation media of (MgO + PGF)/PLA maintained a neutral pH close to a physiological environment. The experiment results indicated the possible mechanism of MgO as the neutralizing agent: the local acidity was buffered as the MgO reacted with the acidic degradation products thereby inhibiting the degradation of PGF from being intensified in an acidic environment. The (MgO + PGF)/PLA composite scaffold appears to be a candidate for bone tissue engineering.

Bioinspired Modifications of PEEK Implants for Bone Tissue Engineering

In recent years, polyetheretherketone (PEEK) has been increasingly employed as an implant material in clinical applications. Although PEEK is biocompatible, chemically stable, and radiolucent and has an elastic modulus similar to that of natural bone, it suffers from poor integration with surrounding bone tissue after implantation. To improve the bioactivity of PEEK, numerous strategies for functionalizing the PEEK surface and changing the PEEK structure have been proposed. Inspired by the components, structure, and function of bone tissue, this review discusses strategies to enhance the biocompatibility of PEEK implants and provides direction for fabricating multifunctional implants in the future.