Profile of a 10-MDP-based universal adhesive system associated with chlorhexidine: Dentin bond strength and in situ zymography performance

Polyvinylpyrrolidone as a primer for resin-dentin bonding

OBJECTIVE

This study aimed to investigate the effects of polyvinylpyrrolidone (PVP)-containing primer (PCP) on dentin bonding.

METHODS

PVP and anhydrous ethanol were used to prepare the PCPs, which were prepared at concentrations of 0.5%, 1%, and 2% (w/v). These PCPs were subsequently applied to the dentin surface, denoted as E1, E2, and E3, respectively. In the control group, no primer was applied. Following the treatment, the dentin surfaces were subjected to analysis using Fourier-transform infrared spectroscopy (FTIR), and the micro-tensile bond strength (MTBS) was evaluated. The failure mode, nanoleakage, and bonding longitudinal section were observed utilizing scanning electron microscopy (SEM). Additionally, the effect of PCPs on matrix metalloproteinases (MMPs) activity was analyzed through an in situ zymography test. Data were subjected to statistical analysis using ANOVA tests (α = 0.05).

RESULTS

Significant alterations in the infrared resonances associated with collagen cross-linking within the collagen matrix were observed across all PCP groups. The application of PCP demonstrated a noteworthy enhancement in micro-tensile bond strength (MTBS) compared to group C (p < 0.05). Notably, group C exhibited the lowest MTBS (41 ± 7.7 MPa), whereas group E2 demonstrated the highest MTBS (66 ± 11.9 MPa). Even after undergoing aging, the MTBS of the PCP groups remained superior to that of group C (p < 0.05). The resin tag length in the PCP groups was found to be greater than that of group C, and the occurrence of nanoleakage was comparatively lower in the PCP groups, both before and after aging. Additionally, PCP exhibited a dose-dependent inhibition of matrix metalloproteinases (MMPs) activity, which was statistically significant (p < 0.05).

CONCLUSIONS

The utilization of PCP Primer exhibits notable enhancements in bond strength, mitigates nano-leakage, and suppresses enzyme activity within the hybrid layer.

Impact of Dentine Pretreatment with Matrix Metalloproteinase Inhibitors on Bond Strength of Coronal Composite Restorations: A Systematic Review and Meta-analysis of In Vitro Studies

Matrix metalloproteinase (MMP) enzymes participate in collagen matrix degradation, including in dentine, potentially compromising bond strength. Therefore, MMP inhibitors have been hypothesized to improve restoration bond strength and stability. This systematic review aimed to evaluate the influence of different MMP inhibitors applied as dentine surface pretreatments on the immediate (24 hours) and longer term (months) bond strength of direct coronal composite restorations. This systematic literature review followed the Preferred Reporting Items for Systematic Review and Meta-analyses (PRISMA) statement. A systematic literature search of three databases (Ovid MEDLINE, Ovid Embase, and Google Scholar) was conducted independently by two reviewers from inception to April 2022. An adapted quality assessment tool was independently applied by two reviewers for risk of bias assessment. RevMan v5.4 software was used for meta-analyses. A randomeffectsmodel was used to generatemean differences with 95% confidence intervals for treatment and control comparisons. The Q-test and I2-test were used to test for heterogeneity. The proportion of total variance across studies attributable to heterogeneity rather than chance was calculated. Overall effects were tested using the Z-test, while subgroup differences were tested using Chi-squared tests. Of 934 studies, 64 studies were included in the systematic review and 42 in the meta-analysis. Thirty-one MMP inhibitors were reported, three of which were included in the meta-analysis: 2% chlorhexidine (CHX), 0.3M carbodiimide (EDC), and 0.1% riboflavin (RIBO). Pretreatment with 2% CHX for 30 and 60 seconds did not significantly improve bond strength compared with controls either immediately or after long-termageing. However, pretreatment with 0.3MEDC and 0.1% RIBO (but not CHX) significantly improved bond strength compared with control groups both immediately and over time. Most studies showed a medium risk of bias. These in vitro findings pave the way for rationale clinical trialing of dentine surface pretreatment with MMP inhibitors to improve clinical outcomes.

Effect of matrix metalloproteinase inhibitors on bonding durability of universal adhesives

This study aimed to evaluate the effect of different matrix metalloproteinase inhibitors (MMPIs) on the microtensile bond strength (μTBS) and nanoleakage of universal adhesives. One hundred twenty non-carious human molars were prepared and randomly assigned to two groups: Scotchbond Bond Universal (SBU) and Gluma Bond Universal (GBU). The samples in each group were assigned to five subgroups (n=12) based on one control (water) and four MMPIs (Benzalkonium-chloride (BAC), Batimastat (BB94), Chlorhexidine (CHX), and Epigallocatechin-gallate (EGCG)). Each adhesive was applied in self-etch (SE) mode or etch-and-rinse (ER) mode. Dentin/composite sticks were fabricated and subjected to the μTBS test after 24 h or 6 months. At 6 months, MMPIs did not affect the μTBS of the adhesives, regardless of etching mode. Nanoleakage was more pronounced in ER mode than in SE mode for all subgroups. All MMPIs, with the exception of CHX, decreased the nanoleakage of GBU in ER mode.

Twenty-month Performance of a Universal Bonding System on Simulated-challenged Dentin Substrates Pretreated with Chlorhexidine

OBJECTIVES

Since the use of dentin antiproteolytic agents with universal adhesives (UAs) can potentially degrade the bonding interface, this study evaluated bond strengths with and without chlorhexidine (CHX) on variously altered dentin surfaces for up to 20 months.

METHODS

Human molar specimens (n=20) were categorized by substrates as S=sound, E=eroded, and C=carious, and by pretreatment as W=water or CHX. These specimens were subjected to micro-tensile bond strength (μTBS) testing at 24 hours, 6 months, and 20 months, after 30 seconds of pretreatment with CHX or W, followed by self-etching and bonding (Adper Single Bond Universal, 3M ESPE). Modes of failure were assessed using optical microscopy (40×) and scanning electron microscopy (SEM), and the results were analyzed by 3-way ANOVA and Tukey's statistical tests (α=0.05).

RESULTS

Substrate (p<0.001), pre-treatment (p=0.0413), and time (p<0.0001) were statistically significant. The sound-dentin group in initial time (W=39.27/CHX=40.55) yielded the higher μTBS values (MPa) in comparison with altered substrates pre-treated with CHX (E-CHX=19.84; C-CHX=18.24) after 20 months, which showed the lowest values. Under SEM analysis, heterogeneous patterns appeared in the hybrid layer of the CHX-treated group, particularly in the altered substrates.

CONCLUSIONS

Bond strength to dentin decreased over a period of 20 months using UA with 10-methacryloyloxydecyl-dihydrogen phosphate (MDP) in self-etching mode. Substrates altered by erosion or caries have impaired adhesion and associated clinical use of UA with MDP and CHX should be avoided.

Effects of the application timing of anti-erosive agents on dentin erosion

This in vitro study aimed to evaluate the effects of the application timing of anti-erosive agents on dentin erosion. Eighty dentin specimens with dimensions of 2 × 2 × 2 mm were prepared and randomly divided into 4 groups based on the treatment solutions: 1.23 × 104 μg/ml sodium fluoride (NaF), 120 μg/ml chlorhexidine (CHX), 300 μg/ml quercetin (QUE), and deionized water (DW, negative control). The specimens in each group were further divided into 2 subgroups according to the application timing of the treatment solutions (n = 10): before the erosive challenges (PRE) and after the erosive challenges (POST). All specimens were submitted to 4 daily erosive challenges for 5 d. For each erosive challenge, the specimens in the subgroup PRE were treated with the respective solutions for 2 min and then immersed in cola drinks for 5 min, while the specimens in the subgroup POST were immersed in cola drinks for 5 min followed by treatment with the respective solutions for 2 min. The erosive dentin loss (EDL) was measured using a contact profilometer, and the surface morphology of the dentin specimens was evaluated by scanning electron microscopy at the end of the experiment. The data were statistically analyzed using two-way analysis of variance (ANOVA) and Bonferroni's test (α = 0.05). Significantly less EDL was observed in the groups NaF, CHX, and QUE than in the group DW (all P < 0.001). Significantly lower EDL was observed in the groups CHX and QUE than in the group NaF (P = 0.001 and P < 0.001, respectively). For CHX, subgroup POST exhibited significantly less EDL than subgroup PRE (P < 0.001). Regarding QUE, subgroup PRE showed significantly less EDL than subgroup POST (P < 0.001). Furthermore, a relatively greater number of obliterated dentinal tubules was visible in the subgroup POST rather than in the subgroup PRE of the group CHX, while in the group QUE, narrower dentinal tubules were observed in the subgroup PRE than those in subgroup POST. In conclusion, CHX and QUE showed the best performance in controlling dentin erosion. CHX was more effective in reducing EDL when applied after erosive challenges, whereas QUE worked more effectively when used before erosive attacks. The application timing should be considered when evaluating the effects of anti-erosive agents because it may determine their effectiveness.

The roles of 10-methacryloyloxydecyl dihydrogen phosphate and its calcium salt in preserving the adhesive-dentin hybrid layer

OBJECTIVES

10-Methacryloyloxydecyl dihydrogen phosphate (MDP) has been regarded as the most effective dentin-bonding monomer for more than 20 years. Although the dentin-bonding promoting effect of MDP has been well demonstrated, the mechanisms by which it benefits the stably of collagen within the adhesive-dentin hybrid layer are not currently fully understood. The objective of this study was to investigate the roles of MDP and its calcium salt in preserving the adhesive-dentin hybrid layer.

METHODS

MDP-conditioned collagen was investigated by Fourier-transform infrared spectroscopy, Ultraviolet-visible spectroscopy, and molecular docking. The structural changes to the dentin surface upon acid-etching and MDP-conditioning were observed by SEM. X-ray diffraction and nuclear magnetic resonance were used to investigate the chemical interactions between MDP and HAp. The collagen-protecting effects of MDP and its Ca salt were investigated using in-situ zymography, rhMMP-9 colorimetric assay, hydroxyproline assay, and molecular docking.

RESULTS

MDP forms a stable collagen-phosphate complex through hydrogen bonding with the collagen in dentin. Furthermore, it generates MDP-Ca salts that are deposited on the dentin collagen scaffold, protecting it from degradation. Moreover, both free MDP and the MDP-Ca salt inhibit matrix metallopeptidase and exogenous proteases, with the inhibitory effect of the calcium salt being significantly stronger than that of the free form.

SIGNIFICANCE

MDP-based adhesives preserve the collagen within the hybrid layer by simultaneously improving collagen's resistance to exogenous enzymes and inhibiting MMP activity, both of which contribute to the longevity of dentin-resin bonding.

Effect of Intraoral Humidity on Dentin Bond Strength of Two Universal Adhesives: An In Vitro Preliminary Study

This study investigated the effect of intraoral humidity on microtensile bond strength (μTBS) to dentin of two universal adhesives applied in self-etch (SE) mode. Forty extracted human molars were selected for this study. Dentin specimens were allocated into four groups, standardized and then bonded with two commercial multimode adhesives, according to two humidity conditions (50% relative humidity (RH) and 90% RH). Following composite resin build-up and 24 h of water storage, the μTBS of the bonded interface was analyzed. The 50% RH was higher for Scotchbond Universal (SBU) than Prime&Bond Universal (PBU), while for 90% RH, SBU had significantly lower values than PBU. With PBU, the mean bond strength was not significantly different between both humidity settings tested (p > 0.05), while for SBU, the mean bond strength was significantly different between both conditions tested (p < 0.05); μTBS was significantly higher for 50% RH than for the other group. Within the limitation of this in vitro study, it can be concluded that: 1) the bonding performance of adhesives systems depends on the humidity settings; 2) increased RH exerts a detrimental effect on the bond strength of 2-hydroxyethyl methacrylate (HEMA)-containing adhesive tested. However, this phenomenon was not observed for HEMA-free adhesive tested; 3) further research in this area is needed to investigate different adhesive systems, temperatures and humidity settings.

Gelatinolytic activity after dentin pretreatment with dimethyl sulfoxide (DMSO) combined to dental bonding systems: Perspectives for biological responses

Endogeneous proteolytic responses in dentin bonding interface have addressing to strategies to preventive and therapeutic approaches of clinical use of dentin bonding systems (DBSs), but still present limitations. The aim of this study was to examine the gelatinolytic profile by means of in situ zymography regarding the use of 1% dimethyl sulfoxide (DMSO) as an aprotic solvent. Sound human third molars were prepared and randomized in 10 groups, following the factors 1- DBS: Adper™ Scotchbond Multipurpose [MP], Adper™ Single Bond 2 [SB], Clearfil™ SE Bond [CSE] and Adper™ Scotchbond Universal - Etch-and-rinse [SU-ER] mode and self-etch mode [SU-SE], 2- dentin pretreatment: Control - Water [C], 2% CHX and 1% DMSO and 3- time: Initial-24 h [I], 6 months [6M] and 30 months [30M]. Pretreatments were applied before primer application for 30s. After restoration, specimens were cut into slices, in which one third were incubated with fluorescein-conjugated gelatin for 24h at 37 °C and analyzed by confocal laser scanning microscopy. The other two-thirds were stored for 6 or 30 months at 37 °C. Fluorescence was quantified using Image J and data was subjected for two-way ANOVA followed by Tukey test (p<0.05). Neither DMSO nor CHX affected initial analyses for any tested conditions. After 6 months, it was observed increased fluorescence for MP using both pretreatments and for SB using only DMSO. Regardless time and pretreatment, CSE and SU-SE showed stabilized gelatinolytic pattern. For SU-ER, both CHX and DMSO were able to maintain a lower fluorescence compared to control group after 6 months. 30-month performance states the susceptibility of degradation for all etched-dentin systems. DMSO pretreatment can be promising to reduce gelatinolytic activity combined with an universal adhesive system under etch-and-rinse mode. For self-etching strategies, DMSO was successful to stabilize the gelatinolytic reactions.

A mussel glue-inspired monomer-etchant cocktail for improving dentine bonding

OBJECTIVES

The humid oral environment adversely affects the interaction between a functionalised primer and dentine collagen after acid-etching. Robust adhesion of marine mussels to their wet substrates instigates the quest for a strategy that improves the longevity of resin-dentine bonds. In the present study, an etching strategy based on the incorporation of biomimetic dopamine methacrylamide (DMA) as a functionalised primer into phosphoric acid etchant was developed. The mechanism and effect of this DMA-containing acid-etching strategy on bond durability were examined.

METHODS

Etchants with different concentrations of DMA (1, 3 or 5 mM) were formulated and tested for their demineralisation efficacy. The interaction between DMA and dentine collagen, the effect of DMA on collagen stability and the collagenase inhibition capacity of the DMA-containing etchants were evaluated. The effectiveness of this new etching strategy on resin-dentine bond durability was investigated.

RESULTS

All etchants were capable of demineralising dentine and exposing the collagen matrix. The latter strongly integrated with DMA via covalent bond, hydrogen bond and Van der Waals' forces. These interactions significantly improve collagen stability and inhibited collagenase activity. Application of the etchant containing 5 mM DMA achieved the most durable bonding interface.

CONCLUSION

Dopamine methacrylamide interacts with dentine collagen in a humid environment and improves collagen stability. The monomer effectively inactivates collagenase activity. Acid-etching with 5 mM DMA-containing phosphoric acid has the potential to prolong the longevity of bonded dental restorations without compromising clinical operation time.

CLINICAL SIGNIFICANCE

The use of 5 mM dopamine methacrylamide-containing phosphoric acid for etching dentine does not require an additional clinical step and has potential to improve the adhesive performance of bonded dental restorations.

Comparison of bond strength of universal adhesives using different etching modes: A systematic review and meta-analysis

This review aims to evaluate whether the etch-and-rinse or self-etch mode is the better protocol for dentin adhesion by universal adhesives. A total of 15 articles were included in the meta-analysis. Two reviewers performed a literature search up to October 2020in four databases: PubMed, Web of Science, Embase, and the Cochrane Library. Without considering the difference in aging mode, the analysis of the immediate and long-term bond strength of dentin showed that there was no statistical significance between the etch-and-rinse and self-etch mode of universal adhesive, and the long-term bond strength decreased relative to the immediate. In vitro studies suggest that prior acid etching did not improve bond performance. Whether from the perspective of long-term bonding performance or simplifying operating procedures, the self-etch mode is preferred.

Bond Strength of Universal Adhesives to Dentin: A Systematic Review and Meta-Analysis

Currently, the availability of a wide variety of universal adhesives makes it difficult for clinicians to choose the correct system for specific bonding situations to dentin substrate. This study aimed to determine whether there are any alternative techniques or additional strategies available to enhance the bond strength of universal adhesives to dentin through a systematic review and meta-analysis. Two reviewers executed a literature search up to September 2020 in four electronic databases: PubMed, ISI Web of Science, Scopus, and EMBASE. Only in vitro studies that reported the dentin bond strength of universal adhesives using additional strategies were included. An analysis was carried out using Review Manager Software version 5.3.5 (The Nordic Cochrane Centre, The Cochrane Collaboration, Copenhagen, Denmark). The methodological quality of each in vitro study was assessed according to the parameters of a previous systematic. A total of 5671 potentially relevant studies were identified. After title and abstract examination, 74 studies remained in systematic review. From these, a total of 61 studies were included in the meta-analysis. The bond strength of universal adhesives to dentin was improved by the use of one of the following techniques: Previous application of matrix metalloproteinases (MMP) inhibitors (p < 0.001), prolonged application time (p = 0.007), scrubbing technique (p < 0.001), selective dentin etching (p < 0.001), non-atmospheric plasma (p = 0.01), ethanol-wet bonding (p < 0.01), prolonged blowing time (p = 0.02), multiple layer application (p = 0.005), prolonged curing time (p = 0.006), and hydrophobic layer coating (p < 0.001). On the other hand, the use of a shortened application time (p = 0.006), and dentin desensitizers (p = 0.01) impaired the bond strength of universal adhesives to dentin. Most of the analyses performed showed a high heterogenicity. The in vitro evidence suggests that the application of universal adhesives using some alternative techniques or additional strategies may be beneficial for improving their bonding performance to dentin. This research received no external funding. Considering that this systematic review was carried out only with in vitro studies, registration was not performed.

Performance of MDP-based system in eroded and carious dentin associated with proteolytic inhibitors: 18-Month exploratory study

The aim of this study was to explore the impact of the interaction between an MDP-based universal adhesive system in etch-and-rinse mode and two proteolytic inhibitors on the longevity of restorations bonded to artificially-affected-dentin substrates. 90 sound human third molars were randomly distributed into three groups according to the substrate: N-no challenges-control (stored in artificial saliva), ACD-artificial caries dentin (6 h DE + 18 h-RE/5 days + 48 h RE) and ERO-artificial erosion dentin (3 × 5 min/5 days with orange juice). They were further redistributed according to dentin pretreatment: W- water (control), CHX-2% digluconate chlorhexidine and E64- 5 μM E64-Trans-Epoxysuccinyl-L-Leucylamido-(4-guanidino) butane, which resulted in the following 9 groups (n = 10): N-W, N-CHX, N-E64, ACD-W, ACD-CHX, ACD-E64, ERO-W, ERO-CHX and ERO-E64. All specimens were restored with Adper Single Bond Universal (Etch-and-rinse mode)/Filtek Z250. Sticks (0.64 mm²) were obtained and subjected to microtensile test (μTBS) in a universal testing machine at 0.5 mm/min for 7-days, 6 and 18-month analyses. Failure modes were classified using optical microscopy (40X). Data were statistically analyzed by three-way ANOVA and Tukey tests (p < 0.05). All individual factors (p < 0.0001) and interaction between factors were statistically significant (substrate X pretreatment (p = 0.00093); substrate X time (p = 0.01035) and pretreatment X time (p = 0.0035). Caries-affected substrate was the most compromised one, disregarding the pretreatment. CHX was mostly affected compared with E64 up to 18 months, possibly due to its calcium-dependent mechanism.