Evaluation of Immediate Bone-Cell Viability and of Drill Wear After Implant Osteotomies: Immunohistochemistry and Scanning Electron Microscopy Analysis

Comparative analysis of bone healing in subcritical defects with air turbine and electric handpiece in a rat model

Rotatory devices are essential in clinical surgical practice, however, depending on the different systems available, their function can impact bone repair and postoperative responses on varying scales. This impact underscores the need to explore new techniques aiming to enhance bone repair. This study aimed to assess the immediate and delayed effects on bone healing in subcritical bone defects using both air turbine and an electric handpiece. For this purpose, 40 male Wistar rats were allocated into two groups. The Control Group (CG) had bone defect made using an air turbine device, while the Experimental Group (EG) had defects made using an electric handpiece. Ten animals were sacrificed for each time of evaluation. Bone neoformation, microstructure, and collagen organization were assessed ate 7, 15 and 30 days postoperative. Inflammatory profiling was conducted at 7 and 15 days. Immediate thermal osteonecrosis were evaluated after the use of rotary systems. Multivariate analysis was used to access statistical differences. The EG exhibited enhanced parameters of bone neoformation in all analyses, with statistical difference between 15 and 30 days (P = .0002) and in comparison with CG in 30 days (P = .0009). A reduced number of inflammatory cells and increased angiogenesis in the initial periods was seen in EG, corroborating the consistent values of collagen type 1 and a decrease of collagen type 3 over times. Immediate thermal osteonecrosis was statistically higher for the CG (P < .05), which showed adequate neoformation of subcritical defects but consistently lower values than those found in the EG. These data suggest that the electric handpiece demonstrated more bone repair area, proving to be an excellent alternative to surgical practice.

Minimizing Invasiveness in Neurosurgical Osteotomies: A Comparative Histomorphometric Study of Piezoelectric Craniotomy versus High-Speed Drill

BACKGROUND

Piezoelectric bone cutting has gained popularity in neurosurgical osteotomies due to perceived lower trauma compared to rotary instruments. However, histological confirmation of its decreased aggressiveness is lacking, hindering conclusive proof. This study compares the bony and neuro-meningeal invasiveness of piezoelectric craniotomy with high-speed drill techniques.

METHODS

Histological data from 21 sheep undergoing piezoelectric craniotomy and 19 sheep subjected to high-speed electric drill craniotomy were compared. Piezoelectric craniotomy utilized a 0.35 mm micro saw titanium nitride coated. Outcome parameters included the detection of the "smear layer," average osteoblast count per high-power field, and residual bone matrix for bony invasiveness assessment. Parameters for meningeal and brain parenchymal invasiveness included pachymeningeal and leptomeningeal injury, gliosis, and histiocytic infiltration. Statistical significance was determined at P < 0.05.

RESULTS

Results showed the Piezo group had fewer frequent smear layers (P <0.001), higher residual bone matrix (P < 0.05), and greater osteoblast counts per high-power field (P < 0.05). Additionally, the Piezo group exhibited lower rates of leptomeningeal injury, cerebral gliosis, and histiocytic infiltration (P < 0.05).

CONCLUSIONS

Piezoelectric craniotomy preserves residual osteoblast viability and leptomeningeal integrity while demonstrating lower rates of thermally induced gliosis and histiocytic infiltration compared to high-speed drills. This suggests the piezoelectric osteotome's minimal invasiveness in bone, meningeal, and brain tissue.

Steel drills versus zirconia drills on heat generation at the surgical site of dental implants: A systematic review and meta-analysis

Objective

The aim was to evaluate the difference in the heat generated between zirconia (Zr) and steel (SS) drills, during implant site preparation.

Material and methods

This systematic review followed the PRISMA methodology criteria and used the JBI Critical Assessment Guidelines for Quasi-Experimental Studies for quality assessment. The electronic search was conducted by using the PubMed/MEDLINE, Embase, and Cochrane Library databases to January 2023. The formulated population, intervention, comparison, outcome (PICO) question was "Do zirconia drills generate less heat than steel drills during implant site preparation?". The meta-analysis was based on an inverse variance (IV) method.

Results

This review included 10 studies in vitro that used zirconia drills compared to steel drills with or without coatings. The meta-analysis indicated a significant difference between Zr drills and SS drills, with a lower bone temperature variation with Zr drills.

Conclusions

Despite the limitations of this review, it was concluded that Zr drills had significantly less temperature variation than SS drills.

The Local Release of Teriparatide Incorporated in 45S5 Bioglass Promotes a Beneficial Effect on Osteogenic Cells and Bone Repair in Calvarial Defects in Ovariectomized Rats

With the increase in the population's life expectancy, there has also been an increase in the rate of osteoporosis, which has expanded the search for strategies to regenerate bone tissue. The ultrasonic sonochemical technique was chosen for the functionalization of the 45S5 bioglass. The samples after the sonochemical process were divided into (a) functionalized bioglass (BG) and (b) functionalized bioglass with 10% teriparatide (BGT). Isolated mesenchymal cells (hMSC) from femurs of ovariectomized rats were differentiated into osteoblasts and submitted to in vitro tests. Bilateral ovariectomy (OVX) and sham ovariectomy (Sham) surgeries were performed in fifty-five female Wistar rats. After a period of 60 days, critical bone defects of 5.0 mm were created in the calvaria of these animals. For biomechanical evaluation, critical bone defects of 3.0 mm were performed in the tibias of some of these rats. The groups were divided into the clot (control) group, the BG group, and the BGT group. After the sonochemical process, the samples showed modified chemical topographic and morphological characteristics, indicating that the surface was chemically altered by the functionalization of the particles. The cell environment was conducive to cell adhesion and differentiation, and the BG and BGT groups did not show cytotoxicity. In addition, the experimental groups exhibited characteristics of new bone formation with the presence of bone tissue in both periods, with the BGT group and the OVX group statistically differing from the other groups (p < 0.05) in both periods. Local treatment with the drug teriparatide in ovariectomized animals promoted positive effects on bone tissue, and longitudinal studies should be carried out to provide additional information on the biological performance of the mutual action between the bioglass and the release of the drug teriparatide.

A new multiphase calcium phosphate graft material improves bone healing-An in vitro and in vivo analysis

This study aims to evaluate the potential of a novel biomaterial synthesized from amorphous calcium phosphate (ACP), octacalcium phosphate (OCP), and hydroxyapatite (HA) to repair critical-sized defects (CSD) in rabbit calvaria. In vitro analyses of cell viability, cell proliferation, formation of mineral nodules, and cell differentiation using qPCR were performed for comparing experimental calcium phosphate (ECP), deproteinized bovine bone (DBB), and beta-tricalcium phosphate (β-TCP). Bilateral CSDs were created in 45 rabbit calvaria. Six groups were evaluated: ECP, ECP + fibrin sealant (ECP + S), coagulum, autogenous bone, DBB, and β-TCP. Euthanasia was performed at 2, 4, and 8 weeks, followed by micro-computed tomography and histological and immunohistochemical analyses. Results from in vitro analyses revealed similar biocompatibility for all tested materials and a tendency for higher gene expression of some bone markers in the ECP group than in β-TCP and DBB groups at 7 days. In contrast to that in DBB and β-TCP groups, ECP displayed growing bone volume over total volume percentage (BV/TV%) with time in vivo. Histological analysis revealed a greater number of giant cells and reduced size of grafted particles in ECP during all periods of analysis. RUNX-2 expression was statistically lower in ECP than DBB at 2 and 4 weeks. Despite no statistical significance, ECP presented the highest absolute values for ALP-expression at 2, 4, and 8 weeks compared with other groups. Together, our findings indicate that a combination of the ACP, OCP, and HA phases into ECP is beneficial and promising for bone regeneration.

Effect of guide sleeve material, region, diameter, and number of times drills were used on the material loss from sleeves and drills used for surgical guides: An in vitro study

STATEMENT OF PROBLEM

How material loss from sleeves and drills is affected when different guide sleeve materials and different sizes of implant drills are used for different regions of surgical guides is unclear.

PURPOSE

The purpose of this in vitro study was to compare the amount of material loss from different guide sleeves (zirconia and cobalt-chromium) and drills of different diameters during osteotomy preparation in different regions.

MATERIAL AND METHODS

Three tooth-supported surgical guides with sleeve holes positioned in the first premolar and second molar sites were prepared. Guide sleeves (Ø 2.20 mm, 3.40 mm, and 4.05 mm) were milled from zirconia (n=60) and cobalt-chromium (n=60) blocks. A total of 12 titanium nitride-coated stainless steel twisted drills (n=6 per sleeve material) of different diameters (Ø 2.00, 3.20, 3.85 mm) were used with corresponding sleeves during the drilling. The weight loss from the drills and the volume loss from the guide sleeves after drilling were analyzed by using multiple linear mixed effect models (α=.05).

RESULTS

According to the 4-way ANOVA for volume loss from sleeves, no significant interaction was found among the 4 main effects (number of times a drill was used, region, diameter, and material), but interactions between the number of times a drill was used and diameter (P=.001) and between the number of times the drill was used and material were significant (P<.001). For weight loss from the drills, a significant interaction was detected between the number of times the drill was used and diameter (P=.024).

CONCLUSIONS

Less sleeve material was lost when zirconia sleeves were used. All sleeves had more material loss in the molar region than in the premolar region. The diameter had varying effects on the amount of material loss from drills and sleeves. The sleeve material and the region did not affect the material loss from drills.

Evaluation of Guided Bone Regeneration in Critical Defects Using Bovine and Porcine Collagen Membranes: Histomorphometric and Immunohistochemical Analyses

Guided bone regeneration (GBR) is a technique used to facilitate bone regeneration, which uses a biocompatible membrane acting as a physical barrier to prevent the adjacent connective tissue from invading the bone defect. The aim of this study was to evaluate and compare the effectiveness of bovine and porcine collagenous membranes as barriers to connective tissue invasion during the repair of critical bone defects in rat calvaria, using histological, histometric, and immunohistochemical analyses. For this study, 72 rats were divided into three groups: clot group (CG), bovine collagen group (BCG), and porcine collagen group (PCG). Analyses were performed on days 7, 15, 30, and 60. The histological results showed that the PCG exhibited bone neoformation starting from day 7, and after 30 days of repair, the surgical defect was completely filled in some animals. For the BCG, there was little bone neoformation activity in the initial periods, and from day 30 onwards, there was an increase in bone neoformation, with a greater increase on day 60. The data obtained in the histometric analysis reveal that, on day 30, the neoformed bone area did not vary greatly between the PCG and the BCG, though both varied from the CG. By day 60, the PCG presented a greater area of neoformation than the BCG. These results were corroborated by the immunohistochemistry results. In view of the results obtained, it can be concluded that all membranes studied in this research promoted GBR.

Effects of the technique and drill design used during the osteotomy on the thermal and histological stimulation

The objective of our in vivo study was to compare the effects of the osteotomy on the thermal alterations, the bone healing and count of polymorphonuclear cells, comparing the drill design (cylindrical or conical) using continuous or intermittent movement. Twelve rabbits were used, which were made four osteotomies (n = 2 per tibia) to simulate the surgical drilling sequence for the installation of a dental implant at 8 mm of length and regular diameter. Four groups were proposed: group G1, cylindrical drill with continuous movement; group G2, cylindrical drill with intermittent movement; group G3, conical drill with continuous movement; and, group G4, conical drill with intermittent movement. Thermal mean variation was 6.91 ± 1.4 °C in group 1, 4.30 ± 1.3 °C in group 2, 2.78 ± 0.6 °C in group 3, and 2.77 ± 0.7 °C in group 4. Whereas the mean area of new bone formation was 1.00 ± 0.3 mm² in group 1, 1.48 ± 0.3 mm² in group 2, 2.20 ± 0.4 mm² in group 3, and 2.43 ± 0.4 mm²in group 4. The mean count of polymorphonuclear cells, in the group 1 was 62.4 ± 5.9 cells, group 2 was 50.7 ± 4.2 cells, group 3 was 44.4 ± 3.7 cells, and group 4 was 42.4 ± 3.7 cells. The conical drill sequence produced a significantly smaller increase in temperature during both techniques (continuous and intermittent), more effective new bone formation and a smaller number of polymorphonuclear cells. During the osteotomy for the installation of implants, the professional must take to consider the drill design to perform a less traumatic surgical technique, which can improve and facilitate the healing of peri-implant tissues.

Bone Healing Evaluation Following Different Osteotomic Techniques in Animal Models: A Suitable Method for Clinical Insights

Osteotomy is a common step in oncological, reconstructive, and trauma surgery. Drilling and elevated temperature during osteotomy produce thermal osteonecrosis. Heat and associated mechanical damage during osteotomy can impair bone healing, with consequent failure of fracture fixation or dental implants. Several ex vivo studies on animal bone were recently focused on heating production during osteotomy with conventional drill and piezoelectric devices, particularly in endosseous dental implant sites. The current literature on bone drilling and osteotomic surface analysis is here reviewed and the dynamics of bone healing after osteotomy with traditional and piezoelectric devices are discussed. Moreover, the methodologies involved in the experimental osteotomy and clinical studies are compared, focusing on ex vivo and in vivo findings.

In-vitro assessment of bone viability with different implant drill speeds

The success of implant osseointegration is clearly impacted by the heat produced throughout the implant osteotomy site preparation. Bone necrosis of the implant bed should be prevented to maintain a stable osseointegration process. The objective of this experiment was to validate the impact of implant drill speed on the bone from the point of view of heat generation; a second objective was to evaluate viability of the osteotomised implant sites in rabbits histologically. Twenty healthy adult rabbits, were randomly categorised into 4 groups; 3 bony osteotomies in the 3 mm, 3.5 mm and 4 mm diameters of the femur were made in each rabbit. Variable speeds were used for the 3 diameters as follow: Group I: speed 1000 rpm, Group II: speed 1500 rpm, Group III: speed 2000 rpm. A combination of speed 2000 rpm for the small diameter drills and the last large diameter with speed 1000 rpm was used in Group IV. The temperature changes were recorded. After the operation, the rabbits were euthanised and the bony samples were taken for histological evaluation. In group III and Group IV, histological analysis demonstrated more bone viability compared to other groups. Furthermore, heat analysis revealed significant differences between group III, Group IV and the other groups with less heat produced with greater speeds compared with lower speeds. Drilling with higher speed in dense bone with irrigation produces less heat and maintains more bone viability compared with lower speed. In addition, increased drill diameter with the same speed or with increased speed generates less heat compared with smaller diameters.

Surgical Drill Bit Design and Thermomechanical Damage in Bone Drilling: A Review

As drilling generates substantial bone thermomechanical damage due to inappropriate cutting tool selection, researchers have proposed various approaches to mitigate this problem. Among these, improving the drill bit design is one of the most feasible and economical solutions. The theory and applications in drill design have been progressing, and research has been published in various fields. However, pieces of information on drill design are dispersed, and no comprehensive review paper focusing on this topic. Systemizing this information is crucial and, therefore, the impetus of this review. Here, we review not only the state-of-the-art in drill bit designs-advances in surgical drill bit design-but also the influences of each drill bit geometries on bone damage. Also, this work provides future directions for this topic and guidelines for designing an improved surgical drill bit. The information in this paper would be useful as a one-stop document for clinicians, engineers, and researchers who require information related to the tool design in bone drilling surgery.

Evaluation of immediate cell viability and repair of osteotomies for implants using drills and piezosurgery. A randomized, prospective, and controlled rabbit study

PURPOSE

The objective of this study was to evaluate the immediate bone damage and bone repair after osteotomy for implants using conventional drills and drills powered by piezoelectric motor.

MATERIALS AND METHODS

Twelve rabbits received a tibial osteotomy with a conventional drill (control), with a diamond like carbon drill (DLC) and with a piezoelectric drill (Piezo). The animals were euthanized immediately, 30 and 60 days postoperatively. The tibias were removed and analyzed by means of histomorphometry, immunohistochemistry and microtomography.

RESULTS

The immediate damage to the tissue at the cavity margins was similar (P > .05). At 30 and 60 days, the amount of newly formed bone tissue was similar (P > .05). Osteocalcin was intense score at 60 days in Piezo group. Microtomography revealed that bone volume at 30 days (control 3.8; DLC 4.3; and Piezo 2.4) and 60 days (control 4.9; DLC 4.82; and Piezo 3.95) were similar. There was a significant difference in bone formation between 30 (2.4) and 60 days (3.95) for the Piezo group (P = .016).

CONCLUSION

The immediate effects and repair of cavities made using conventional, DLC coated, or ultrasound drills were similar.

The Effects of Liquid Disinfection and Heat Sterilization Processes on Implant Drill Roughness: Energy Dispersion X-ray Microanalysis and Infrared Thermography

BACKGROUND

The aim of this study is to evaluate effects on stainless steel (SS) and zirconia implant drills of 50 cycles of sterilization through different processes.

METHODS

A total of 24 SS and 24 zirconia drills were treated with 3 different sterilization processes: 50 cycles of immersion in glutaraldehyde 2%, 50 cycles in 6% hydrogen peroxide and 50 cycles of heat. Energy-dispersive X-ray spectroscopy (EDX) was used to compare the effect of the different treatments compared to new untreated controls. Infrared thermography was used to measure the increase of temperature during drilling on bone ribs. A scanning electron microscopy (SEM) was used to measure the roughness of the samples.

RESULTS

Zirconia drills seem not to be affected by the different treatments; no significant differences were found with EDX nor through thermography controls. SS drills were affected by the different treatments, as confirmed by the increased roughness of the SS samples after all the cycles of sterilization/disinfection, measured at SEM. On the contrary, the zirconia drills roughness was not particularly affected by the chemical and thermal cycles. Significant differences were observed regarding the temperature, between steel and zirconia drills (p < 0.01).

CONCLUSIONS

The disinfection agents had a weak impact on the temperature changes during implant bone preparation, while heat sterilization processes had no effect on either of the drills evaluated. The disinfection agents increased the roughness of the steel drills, while they had no effect on the zirconia drills.

Long-term stability behavior of paramedian palatal mini-implants: A repeated cross-sectional study

INTRODUCTION

The initial stability of orthodontic mini-implants is well investigated over a period of 6 weeks. There is no clinical data available dealing with the long-term stability. The aim of this study was the assessment of long-term stability of paramedian palatal mini-implants in humans.

METHODS

Stability of 20 implants was measured after removal of the orthodontic appliance (sliding mechanics for sagittal molar movement 200 cN each side) before explantation (T4) using resonance frequency analysis (RFA). Data were compared with a matched group of 21 mini-implants assessing the stability immediately after insertion, and after 2, 4, and 6 weeks (T0-T3). The mini-implants used in this study were machined self-drilling titanium implants (2.0 × 9.0 mm). Gingival thickness at the insertion site was 1-2 mm.

RESULTS

The implant stability quotient (ISQ) values before removal of the implant at T4 were 25.2 ± 2.9 after 1.7 ± 0.2 years and did not show a statistically significant change over time compared with the initial healing group (T0-T3).

CONCLUSIONS

Comparing the stability of mini-implants just after completion of the healing period and at the end of their respective usage period revealed no significant difference. An increase of secondary stability could not be detected. The level of stability seemed to be appropriate for orthodontic anchorage.

Cyclosporine A impairs bone repair in critical defects filled with different osteoconductive bone substitutes

The aim of this study was to assess the influence of cyclosporine administration on the repair of critical-sized calvaria defects (CSDs) in rat calvaria filled with diverse biomaterials. Sixty animals were divided into two groups: the control (CTR) group (saline solution) and the cyclosporine (CCP) group (cyclosporine, 10 mg/kg/day). These medications were administered daily by gavage, beginning 15 days before the surgical procedure and lasting until the day the animals were euthanized. A CSD (5 mm Ø) was made in the calvaria of each animal, which was allocated to one of 3 subgroups, according to the biomaterial used to fill the defect: coagulum (COA), deproteinized bovine bone (DBB), or biphasic calcium phosphate ceramics of hydroxyapatite and β-phosphate tricalcium (HA/TCP). Euthanasia of the animals was performed 15 and 60 days after the surgical procedure (n = 5 animals/period/subgroup). Bone repair (formation) assessment was performed through microtomography and histometry, while the analyses of the expression of the BMP2, Osteocalcin, and TGFβ1 proteins were performed using immunohistochemistry. The CSDs not filled with biomaterials demonstrated lower bone formation in the CCP group. At 15 days, less bone formation was observed in the CSDs filled with DBB, a smaller volume of mineralized tissue was observed in the CSDs filled with HA/TCP, and the expression levels of BMP2 and osteocalcin were lower in the CCP group compared to the CTR group. The use of cyclosporine impaired bone repair in CSD, and this effect can be partially explained by the suppression of BMP2 and osteocalcin expression.

Experimental investigation on the effect of drill quality on the performance of bone drilling

Bone drilling is a well-known process in operative fracture treatment and reconstructive surgery. The cutting ability of the drill is lost when used for multiple times. In this study, the effect of different levels of drill wear on bone temperature, drilling force, torque, delamination around the drilling region and surface roughness of the hole was investigated using a series of experiments. Experimental results demonstrated that the wear of the drill is strongly related to the drilling force, torque, temperature and surface roughness of the drilled hole. Statistical analysis was performed to find the effect of various factors on multiple response variables in the bone drilling process. The favorable conditions for bone drilling are obtained when feed rate, drill speed and the roughness of the cutting edge of the drill were fixed at 30 mm, 2000 rpm and up to 2 mm, respectively. Further, analysis of variance (ANOVA) was performed to determine the factor with a significant impact on the response variables. F-test and p-value indicated that the feed rate had the highest effect on grey relational grade followed by the roughness of the drill. This study suggests that the sharp drill along with controlled drilling speed and feed rate may be used for safe and efficient surgical drilling in bone.

Systemic and local effects of radiotherapy: an experimental study on implants placed in rats

OBJECTIVES

Evaluate the modulating effect of ionizing radiation, blood cytokine levels, and bone remodeling of the interface around the implant to understand the radiation mechanisms which can impair the implants receptor site.

MATERIAL AND METHODS

Sixty rats were submitted to grade V titanium implants in the femurs and were divided into the following groups: no-irradiation (N-Ir): control group with implant only; early-irradiation (E-Ir): implant + irradiation after 24 h; late-irradiation (L-Ir): implant + irradiation after 4 weeks; and previous-irradiation (P-Ir): irradiation + implant after 4 weeks. The animals in the E-Ir, L-Ir, and P-Ir groups were irradiated in two fractional stages of 15 Gy. At 3 days, 2 weeks, and 7 weeks after the final procedure, five animals were randomly euthanized per group. Serum levels of TNF-ɑ, IL-1β, TGF-β, IL-6, M-CSF, and IL-10 were measured from blood collected prior to euthanasia using the ELISA test. The pieces containing the implants were subjected to immunohistochemical labeling using the tartrate acid resistant to phosphatase, osteocalcin, and caspase-3 markers and mCT. The ANOVA test was used for statistical analysis, and the Tukey multiple comparison test (p < 0.05) was applied.

RESULTS

The results indicated that ionizing radiation modifies the production of pro- and anti-inflammatory serum cytokines, the expression of proteins involved in bone remodeling and cellular apoptosis, as well as changes in bone formation.

CONCLUSIONS

The results suggests that a longer period between radiotherapy and implant placement surgery when irradiation occurs prior to implant installation would allow the recovery and renewal of bone cells and avoid future failures in osseointegration.

CLINICAL RELEVANCE

The search for modifications caused by ionizing irradiation in bone tissue can indicate the ideal period for implant placement without affecting the osseointegration process.

Evaluation of Surgical Bur Deformation and Bone Surface Roughness After Multiple Uses

PURPOSE

The aim of the present in vitro study was to microscopically evaluate and describe the deformation of Lindeman surgical burs and the bone surface roughness after repeated osteotomies and sterilization cycles.

MATERIALS AND METHODS

Twenty-one Lindeman surgical burs were analyzed under scanning electron microscopy (SEM) to evaluate the damage of the bur's integrity after 0, 1, 3, 5, 7, or 9 osteotomies on bovine ribs. Eighteen bone specimens were obtained after osteotomy for roughness analysis using profilometry. One-way analysis of variance was used to compare the mean roughness values across the experimental groups, and P ≤ .05 was considered to indicate statistical significance.

RESULTS

Representative SEM images illustrated that all analyzed burs presented with some type of deformation at both the tip and the body, even after their first use. The mean roughness values were independent of the number of uses (P > .05); however, the standard deviation increased with the number of uses of the burs.

CONCLUSIONS

These results suggest that even after their first use, rotatory surgical burs will have some type of deformation and that their cutting efficiency on the bone will vary and will be difficult to predict.

Potential Causes of Titanium Particle and Ion Release in Implant Dentistry: A Systematic Review

Implant surface characteristics, as well as physical and mechanical properties, are responsible for the positive interaction between the dental implant, the bone and the surrounding soft tissues. Unfortunately, the dental implant surface does not remain unaltered and changes over time during the life of the implant. If changes occur at the implant surface, mucositis and peri-implantitis processes could be initiated; implant osseointegration might be disrupted and bone resorption phenomena (osteolysis) may lead to implant loss. This systematic review compiled the information related to the potential sources of titanium particle and ions in implant dentistry. Research questions were structured in the Population, Intervention, Comparison, Outcome (PICO) framework. PICO questionnaires were developed and an exhaustive search was performed for all the relevant studies published between 1980 and 2018 involving titanium particles and ions related to implant dentistry procedures. Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines were followed for the selection and inclusion of the manuscripts in this review. Titanium particle and ions are released during the implant bed preparation, during the implant insertion and during the implant decontamination. In addition, the implant surfaces and restorations are exposed to the saliva, bacteria and chemicals that can potentially dissolve the titanium oxide layer and, therefore, corrosion cycles can be initiated. Mechanical factors, the micro-gap and fluorides can also influence the proportion of metal particles and ions released from implants and restorations.

Measurement of temperature induced in bone during drilling in minimally invasive foot surgery

INTRODUCTION

There has been growing interest in minimally invasive foot surgery due to the benefits it delivers in post-operative outcomes in comparison to conventional open methods of surgery. One of the major factors determining the protocol in minimally invasive surgery is to prevent iatrogenic thermal osteonecrosis. The aim of the study is to look at various drilling parameters in a minimally invasive surgery setting that would reduce the risk of iatrogenic thermal osteonecrosis.

METHOD

Sixteen fresh-frozen tarsal bones and two metatarsal bones were retrieved from three individuals and drilled using various settings. The parameters considered were drilling speed, drill diameter, and inter-individual cortical variability. Temperature measurements of heat generated at the drilling site were collected using two methods; thermocouple probe and infrared thermography. The data obtained were quantitatively analysed.

RESULTS

There was a significant difference in the temperatures generated with different drilling speeds (p<0.05). However, there was no significant difference in temperatures recorded between the bones of different individuals and in bones drilled using different drill diameters. Thermocouple showed significantly more sensitive tool in measuring temperature compared to infrared thermography.

CONCLUSION

Drilling at an optimal speed significantly reduced the risk of iatrogenic thermal osteonecrosis by maintaining temperature below the threshold level. Although different drilling diameters did not produce significant differences in temperature generation, there is a need for further study on the mechanical impact of using different drill diameters.

Comparative Evaluation of Cell Viability Immediately After Osteotomy for Implants With Drills and Piezosurgery: Immunohistochemistry Analysis

OBJECTIVE

To evaluate the effect of reusing drills and piezosurgery tips during implant osteotomy on immediate bone cell viability through immunohistochemical analysis.

MATERIALS AND METHODS

Six male rabbits were divided into 2 groups and then divided into 5 subgroups-correspond to drills and tips used 10, 20, 30, 40, and 50 times, respectively. All animals received 10 osteotomies in each tibia, by use of the classic drilling procedure in one group (G1) and the piezosurgery device in the other group (G2). For immunohistochemical technique were utilized the osteoprotegerin, RANKL, osteocalcin, and caspase 3. Control procedures were performed by omitting the primary antibodies (negative control).

RESULTS

Bone formation and resorption responses presented in more intense way during the piezosurgery. The expression of osteocalcin had become quite intense in piezosurgery groups, but with reduced immunostaining from the 30th osteotomy. The caspase 3 showed the viability of the osteoblast from the 20th osteotomy with piezosurgery and remained constant until the 50th.

CONCLUSION

Piezosurgery provides greater osteoblastic cell viability than the system of conventional drilling.

CLINICAL RELEVANCE

This study will provide data so that the authors can recycle the drills and tips for implant placement, thus enabling a better cell viability for osseointegration.

In-situ tool wear monitoring and its effects on the performance of porcine cortical bone drilling: a comparative in-vitro investigation

Background

Drilling is one of the most widely used process in orthopaedic surgical operation and the same drill bit is used a number of times in hospitals. Using the same drill bit a several times may be the cause of osteosynthesis and osteonecrosis.

Methods

In the present work, the effect of repeated orthopaedic surgical twist drill bit on the tool wear, force, torque, temperature and chip morphology during porcine cortical bone drilling is studied. Results were compared with rotary ultrasonic drilling (RUD) on the same bone using a hollow drill tool coated with diamond grains. A sequence of 200 experiments (100 with each process, RUD and CD) were performed with constant process parameters.

Results

Wear area on the drill bit is significantly increased as the drill bit is used repeatedly in CD, whereas no attritious wear was found on the diamond coated grains in RUD.

Conclusions

Comparative results showed that cutting force, torque and temperature increased as a function of tool wear in CD as the same drill bit was used a number of times. No significant variation in the cutting force and torque was observed in RUD as the number of drilled holes increased.

Evaluation of bone substitutes for treatment of peri-implant bone defects: biomechanical, histological, and immunohistochemical analyses in the rabbit tibia

Purpose

We sought to evaluate the effectiveness of bone substitutes in circumferential peri-implant defects created in the rabbit tibia.

Methods

Thirty rabbits received 45 implants in their left and right tibia. A circumferential bone defect (6.1 mm in diameter/4 mm depth) was created in each rabbit tibia using a trephine bur. A dental implant (4.1 mm × 8.5 mm) was installed after the creation of the defect, providing a 2-mm gap. The bone defect gaps between the implant and the bone were randomly filled according to the following groups: blood clot (CO), particulate Bio-Oss^® (BI), and Bio-Oss^® Collagen (BC). Ten animals were euthanized after periods of 15, 30, and 60 days. Biomechanical analysis by means of the removal torque of the implants, as well as histologic and immunohistochemical analyses for protein expression of osteocalcin (OC), Runx2, OPG, RANKL, and TRAP were evaluated.

Results

For biomechanics, BC showed a better biological response (61.00±15.28 Ncm) than CO (31.60±14.38 Ncm) at 30 days. Immunohistochemical analysis showed significantly different OC expression in CO and BC at 15 days, and also between the CO and BI groups, and between the CO and BC groups at 60 days. After 15 days, Runx2 expression was significantly different in the BI group compared to the CO and BC groups. RANKL expression was significantly different in the BI and CO groups and between the BI and BC groups at 15 days, and also between the BI and CO groups at 60 days. OPG expression was significantly higher at 60 days postoperatively in the BI group than the CO group.

Conclusions

Collectively, our data indicate that, compared to CO and BI, BC offered better bone healing, which was characterized by greater RUNX2, OC, and OPG immunolabeling, and required greater reversal torque for implant removal. Indeed, along with BI, BC presents promising biomechanical and biological properties supporting its possible use in osteoconductive grafts for filling peri-implant gaps.

Influence of implant drill materials on wear, deformation, and roughness after repeated drilling and sterilization

PURPOSE

The aim of this study was to evaluate deformation, roughness, and mass loss of stainless steel, diamond-like carbon (DLC)-coated and zirconia drills after multiple osteotomies with sterilization procedures.

MATERIALS AND METHODS

Drilling procedures were performed using stainless steel (G1), DLC-coated (G2), and zirconia (G3) drills. All groups were divided in subgroups 1, 2, 3, 4, and 5, corresponded to drills used 0, 10, 20, 30, and 40 times, respectively.

RESULTS

No significant differences in mass and roughness were detected among all groups and subgroups. In SEM images, all groups revealed signs of wear while coating delamination was detected in G2. Drills from G1 displayed more irregular surface, whereas cutting edges were more regular in G3.

CONCLUSION

Zirconia drills presented more regular surfaces whereas stainless steel drills revealed more severe signs of wear. Further studies must be performed to evaluate the putative influence of these findings in heat generation.

Effects on Bone Repair of Osteotomy With Drills or With Erbium, Chromium: Yttrium-Scandium-Gallium-Garnet Laser: Histomorphometric and Immunohistochemical Study

BACKGROUND

The erbium, chromium:yttrium-scandium-gallium-garnet (Er,Cr:YSGG) laser has been widely used in the dental clinic; however, few studies have demonstrated the advantages of the use of this laser for bone osteotomies. The purpose of this study is to evaluate and compare the bone repair process of defects generated by the Er,Cr:YSGG laser or conventional drills.

METHODS

Ninety-six rats were divided into two groups of 48 animals (drill group and laser group). After surgical exposure of the right tibia, the animals were subjected to a 2-mm-diameter osteotomy created by conventional drills (drill group) or by the Er,Cr:YSGG laser (laser group). The animals were sacrificed 0, 3, 7, 14, 30, and 60 days after the creation of the defect, and histologic sections were obtained and used for histomorphometric and immunohistochemical analyses for the detection of osteocalcin, osteoprotegerin, receptor activator of nuclear factor κ-B ligand, vascular endothelial growth factor, and caspase-3.

RESULTS

The osteotomy with the drill produced well-delimited and smooth walls, whereas the osteotomies in the laser group were irregular and presented an amorphous basophilic line and bone necrosis that was slowly resorbed during the repair process. Despite these characteristics, bone repair was similar between groups at various time points, and, at 60 days, the defects in both groups were completely repaired by newly formed bone.

CONCLUSION

The repair process of osteotomies created by the Er,Cr:YSGG laser, despite producing thermal damage to bone tissue, is comparable to that with conventional drills.

Heat generation and drill wear during dental implant site preparation: systematic review

To identify factors that minimise damage during the drilling of sites for dental implants, we reviewed published papers on the amount of heat that is generated. We systematically searched English language studies published between January 2000 and February 2014 on MEDLINE/PubMed and found 41 articles, of which 27 related to an increase in temperature during preparation of the site. We found only basic research with a low level of evidence. Most of the studies were in vitro, and osteotomies were usually made in non-vital bone from cows or pigs. To measure heat in real time, thermocouples were used in 18 studies and infrared thermographs in 7. Three studies reported the use of immunohistochemical analysis to investigate immediate viability of cells. The highest temperature measured was 64.4°C and the lowest 28.4°C. Drill wear was reported after preparation of 50 sites, and there was a significant increase in temperature and a small change in the physiological balance of the proteins in the bone cells. Differences in the study designs meant that meta-analysis was not appropriate. For future work, we recommend the use of standard variables: an axial load of 2kg, drilling speed of 1500rpm, irrigation, standard artificial bone blocks, and the use of infrared thermography.

Clinical study on survival rate of short implants placed in the posterior mandibular region: resonance frequency analysis

OBJECTIVE

Short implants are increasingly used, but there is doubt about their performance being similar to that of regular implants. The aim of this study was to compare the mechanical stability of short implants vs. regular implants placed in the edentulous posterior mandible.

MATERIAL AND METHODS

Twenty-three patients received a total of 48 short implants (5 × 5.5 mm and 5 × 7 mm) and 42 regular implants (4 × 10 mm and 4 × 11.5 mm) in the posterior mandible. Patients who received short implants had <10 mm of bone height measured from the bone crest to the outer wall of the mandibular canal. Resonance frequency analysis (RFA) was performed at time intervals T0 (immediately after implant placement), T1 (after 15 days), T2 (after 30 days), T3 (after 60 days), and T4 (after 90 days).

RESULTS

The survival rate after 90 days was 87.5% for the short implants and 100% for regular implants (P < 0.05). There was no significant difference between the implants in time intervals T1, T2, T3, and T4. In T0, the RFA values of 5 × 5.5 implants were higher than values of 5 × 7 and 4 × 11.5 implants (P < 0.05). A total of six short implants that were placed in four patients were lost (three of 5 × 5.5 mm and three of 5 × 7 mm). Three lost implants started with high ISQ values, which progressively decreased. The other three lost implants started with a slightly lower ISQ value, which rose and then began to fall.

CONCLUSIONS

Survival rate of short implants after 90 days was lower than that of regular implants. However, short implants may be considered a reasonable alternative for rehabilitation of severely resorbed mandibles with reduced height, to avoid performing bone reconstruction before implant placement. Patients need to be aware of the reduced survival rate compared with regular implants before implant placement to avoid disappointments.

Rehabilitation of the maxillary arch after bone graft using immediate loading with implant-supported fixed restoration

Moderate and controlled loading environments support or enhance osteogenesis, and, consequently, a high degree of bone-to-implant contact can be acquired. This is because when osteoprogenitor cells are exposed to limited physical deformation, their differentiation into osteoblasts is enhanced. Then, some range of microstrain is considered advantageous for bone ingrowth and osseointegration. The primary stability has been considered one of the main clinical means of controlling micromotion between the implant and the forming interfacial tissue, which helps to establish the proper mechanical environment for osteogenesis. Based on the biological aspects of immediate loading (IL), the objective of this study is to present a clinical case of maxillary arch rehabilitation using immediate loading with implant-supported fixed restoration after bone graft. Ten dental implants were placed in the maxilla 6 months after the autogenous bone graft, removed from the mandible (bilateral oblique line and chin), followed by the installation of an immediate-load fixed cross-arch implant-supported restoration because primary stability was reached for 8 implants. In addition, instructions about masticatory function and how it is related to interfacial micromotion were addressed and emphasized to the patient. The reasons for the IL were further avoidance of an interim healing phase, a potential reduction in the number of clinical interventions for the patient, and aesthetic reasons. After monitoring the rehabilitation for 8 years, the authors can conclude that maxillary IL can be performed followed by a well-established treatment planning based on computed tomography, providing immediate esthetics and function to the patient even when autogenous bone graft was previously performed in the maxilla.

Dynamics of bone healing after osteotomy with piezosurgery or conventional drilling - histomorphometrical, immunohistochemical, and molecular analysis

BACKGROUND

Piezosurgery is an osteotomy system used in medical and dental surgery. Many studies have proven clinical advantages of piezosurgery in terms of quality of cut, maneuverability, ease of use, and safety. However, few investigations have tested its superiority over the traditional osteotomy systems in terms of dynamics of bone healing. Therefore, the aim of this study was to evaluate the dynamics of bone healing after osteotomies with piezosurgery and to compare them with those associated to traditional bone drilling.

METHODS

One hundred and ten rats were divided into two groups with 55 animals each. The animals were anesthetized and the tibiae were surgically exposed to create defects 2 mm in diameter by using piezosurgery (Piezo group) and conventional drilling (Drill group). Animals were sacrificed at 3, 7, 14, 30 and 60 days post-surgery. Bone samples were collected and processed for histological, histomorphometrical, immunohistochemical, and molecular analysis. The histological analysis was performed at all time points (n = 8) whereas the histomorphometrical analysis was performed at 7, 14, 30 and 60 days post-surgery (n = 8). The immunolabeling was performed to detect Vascular Endothelial Growth Factor (VEGF), Caspase-3 (CAS-3), Osteoprotegerin (OPG), Receptor Activator of Nuclear Factor kappa-B Ligand (RANKL), and Osteocalcin (OC) at 3, 7, and 14 days (n = 3). For the molecular analysis, animals were sacrificed at 3, 7 and 14 days, total RNA was collected, and quantification of the expression of 21 genes related to BMP signaling, Wnt signaling, inflammation, osteogenenic and apoptotic pathways was performed by qRT-PCR (n = 5).

RESULTS

Histologically and histomorphometrically, bone healing was similar in both groups with the exception of a slightly higher amount of newly formed bone observed at 30 days after piezosurgery (p < 0.05). Immunohistochemical and qRT-PCR analyses didn't detect significant differences in expression of all the proteins and most of the genes tested.

CONCLUSIONS

Based on the results of our study we conclude that in a rat tibial bone defect model the bone healing dynamics after piezosurgery are comparable to those observed with conventional drilling.

The rabbit as experimental model for research in implant dentistry and related tissue regeneration

The use of rabbits for experimental research has a long historical tradition. The aim of this review consists in outlining the use of the rabbit for research in implant dentistry and related tissue regeneration. Rabbits appear as a first-hand choice for fundamental implant design studies because of their size, easy handling, short life span, and economical aspects in purchasing and sustaining. In the following, the various anatomical sites in the rabbit will be summarized to provide an overview of current possibilities and limitations of this model for bone research in oral implantology.

Guided implant surgery: what is the influence of this new technique on bone cell viability?

PURPOSE

To evaluate the effect of implant osteotomy on immediate bone cell viability, comparing guided surgery for implant placement with the classic drilling procedure.

MATERIALS AND METHODS

For this study, 20 rabbits were used. The animals were divided into a guided surgery group (GG) and a control group (CG) and were then divided into 4 subgroups--subgroups 1, 2, 3, and 4--corresponding to drills used 10, 20, 30, and 40 times, respectively. All animals received 5 osteotomies in each tibia, by use of the classic drilling procedure in one tibia and guided surgery in the other tibia. The osteotomized areas were removed and processed immunohistochemically for detection of osteocalcin, receptor activator of nuclear factor κB ligand (RANKL), osteoprotegerin (OPG), and caspase 3.

RESULTS

Immunohistochemical analysis showed that osteocalcin expression was initially higher in the CG and remained constant after drill reutilization. Although the expressions of RANKL and OPG were not statistically different for the GG and CG, the RANKL/OPG ratio tended to be higher for the GG. Moreover, caspase 3 expression was elevated in the GG, proportionally to the number of osteotomies, indicating an increase in the apoptosis index in the GG.

CONCLUSIONS

The classic drilling procedure is more favorable to cell viability than guided surgery.

Evaluation of deformation, mass loss, and roughness of different metal burs after osteotomy for osseointegrated implants

PURPOSE

This study used bovine ribs to comparatively assess the deformation, roughness, and mass loss for 3 different types of surface treatments with burs, used in osteotomies, for the installation of osseointegrated implants.

MATERIALS AND METHODS

The study used 25 bovine ribs and 3 types of helical burs (2.0 mm and 3.0 mm) for osteotomies during implant placement (a steel bur [G1], a bur with tungsten carbide film coating in a carbon matrix [G2], and a zirconia bur [G3]), which were subdivided into 5 subgroups: 1, 2, 3, 4, and 5, corresponding to 0, 10, 20, 30, and 40 perforations, respectively. The surface roughness (mean roughness [Ra], partial roughness, and maximum roughness) and mass (in grams) of all the burs were measured, and the burs were analyzed in a scanning electron microscope before and after use. Data were tabulated and statistically analyzed by use of the Kruskal-Wallis test, and when a statistically significant difference was found, the Dunn test was used.

RESULTS

There was a loss of mass in all groups (G1, G2, and G3), and this loss was gradual, according to the number of perforations made (1, 2, 3, 4, and 5). However, this difference was not statistically significant (P < .05). Regarding the roughness, G3 presented an increase in Ra, partial roughness, and maximum roughness (P < .05) compared with G2 and an increase in Ra compared with G1. There was no statistically significant difference (P > .05) between G1 and G2. The scanning electron microscopy analysis found areas of deformation in all the 2.0-mm samples, with loss of substrates, and this characteristic was more frequent in G3.

CONCLUSIONS

The 2.0-mm zirconia burs had a greater loss of substrates and abrasive wear in the cutting area. They also presented an increased roughness when compared with the steel and the tungsten carbide coating film in carbon matrix. There was no statistically significant difference (P < .05) between G1 and G2 in any mechanical test carried out.

Influence of a resilient, hard-carbon thin film on drilling efficiency and thermogenesis

OBJECTIVE

To determine changes in drill bit performance attributable to application of a triaxially resilient, hard-carbon thin film.

STUDY DESIGN

In vitro mechanical study.

METHODS

Five matched pairs of control bits and bits with a carbon nanofilm applied were tested in equine cortical bone and a synthetic bone substrate. Thirty sequential holes were drilled with each bit. Drilling time was recorded for all holes. Maximum substrate temperature was measured with infrared thermography for holes 1, 15, and 30. Drilling time, prolongation of drilling time over successive uses, and maximum substrate temperature were compared between control and test bits in each substrate.

RESULTS

Drilling time was significantly reduced with test bits in both substrates. Drilling time over successive osteotomies increased more slowly with test bits than with control bits. Test bits generated significantly lower substrate temperatures during drilling.

CONCLUSIONS

Bits with the carbon nanofilm completed osteotomy faster and generated less heat than control bits. Test bits also had less degradation of drilling performance with repeated use.