Zn-Fe mixed metal oxides from metal hydroxide precursor: Effect of calcination temperature on phase evolution, porosity, and catalytic acidity

Effect of Tetrahedrally Coordinated Al on the Surface Acidity of Mg-Al Binary Mixed Oxides

Metal oxides (MOs) having Mg and Al with Mg/Al ratios of 1, 2, 3, and 4 were synthesized via calcination of the layered double hydroxides (LDH). The X-ray diffraction analysis revealed that all the MO consisted of periclase (MgO) crystallite with comparable crystallinity regardless of the metal ratio. According to the 27Al magic-angle spinning nuclear magnetic resonance, the phase transformation from LDH to MO upon calcination facilitated the evolution of the Al3+ ions with unsaturated coordination at the surface of MO. The specific surface area values of MOs were not significantly different from each other, ranging between 100 and 200 m2/g, suggesting that the metal ratio did not strongly influence the porous structure of MO. The temperature-dependent desorption of ammonia demonstrated that the Lewis acidity of the Al-rich MOs was the largest with an Mg/Al ratio of 1, attributed to the efficient exposure of the surface-active site Al3+-O2- pairs. The acidity of heterogenous Al-rich MOs significantly increased with the exposed tetrahedral Al site on the surface and dramatically diminished when the molar ratio (Mg/Al) was over two.

Hydrothermal synthesis of cobalt substitute zinc-ferrite (Co1-xZnxFe2O4) nanodot, functionalised by polyaniline with enhanced photocatalytic activity under visible light irradiation

Fabrication and development of effective visible-light-responsive photocatalysts are required to tackle critical environmental issues. The aim of this study was to develop a nanocomposite material with improved photocatalytic activity for the degradation of industrial dyes such as Reactive Orange-16 (RO-16), Reactive Blue (RB-222), Reactive Yellow-145 (RY-145), and Disperse Red-1 (DR-1) without the need for a post-separation process after use. Here we report the hydrothermal synthesis of nanodots of Co_1-xZn_xFe₂O₄ (x = 0.3, 0.5 and 0.7), coated with polyaniline, by in situ polymerization. The Co_1-xZn_xFe₂O₄ nanodots, coated with polyaniline (PANI) nanograins, facilitated optical properties by easily capturing visible light. X-ray Diffraction (XRD) patterns and Scanning Electron Microscopy (SEM) images have confirmed the single-phase spinel structure of Co_1-xZn_xFe₂O₄ nanodot and nano-pore size of the Co_1-xZn_xFe₂O₄/PANI nanophotocatalyst. The specific surface area of the Brunauer-Emmett-Teller (BET) of the Co_1-xZn_xFe₂O₄/PANI photocatalyst was determined to be 24.50 m²/g by multipoint analysis. The final Co_1-xZn_xFe₂O₄/PANI (x = 0.5) nanophotocatalyst showed high efficiency in the catalytic degradation of toxic dyes (∼98% within 5 min), with good mechanical stability and recyclability under visible light irradiation. The nanophotocatalyst was re-used and its efficiency was largely maintained, even after seven cycles (∼82%) of degradation. The effects of various parameters, such as initial dye concentration, nanophotocatalyst concentration, initial pH of dye solution, and reaction kinetics were studied. According to the Pseudo-first-order kinetic model, photodegradation data followed the first-order reaction rate (R² > 0.95) of degradation of dyes. In conclusion, a simple and low-cost synthesis process, speedy degradation and excellent stability of polyaniline-coated Co_1-xZn_xFe₂O₄ nanophotocatalyst could be used as a promising photocatalyst for dye-wastewater treatment.

Chitosan/tannic acid/ZnFe layered double hydroxides and mixed metal oxides nanocomposite for the adsorption of reactive dyes

The fabrication of the environmentally friendly nanocomposite beads containing chitosan (Chi), tannic acid (TA), layered double hydroxides (LDH), and mixed metal oxides (MMO) was carried out. The synthesized ZnFe LDH, ZnFe MMO, and fabricated beads (Chi/TA@LDH and Chi/TA@MMO) were characterized using FESEM, XRD, FTIR, BET, and TGA. The beads were applied for the simultaneous removal of three reactive dyes. The design of experiments was based on a full factorial design considering the effect of six independent variables (initial dye concentrations, adsorbent dosage, time, and adsorbent type) on the dye removal percentages (DR%) of each dye. Regression equations were extracted from the experimental results (R² > 0.983) and high obtained F-values from analysis of variance (ANOVA) proved the significance of the models. The maximum adsorption capacity of the dyes onto, Chi/TA@LDH and Chi/TA@MMO beads were between 257 and 483 mg g^-1. The spontaneity and exothermic nature of the adsorption processes were determined by thermodynamic studies (-8 < ΔH° (KJ mol^-1) < -1, -22 < ΔG° (KJ mol^-1) < -18). Reusability studies showed that the fabricated beads could be regenerated and applied several times.

Waste Valorization of a Recycled ZnCoFe Mixed Metal Oxide/Ceftriaxone Waste Layered Nanoadsorbent for Further Dye Removal

Waste valorization of spent wastewater nanoadsorbents is a promising technique to support the circular economy strategies. The terrible rise of heavy metal pollution in the environment is considered a serious threat to the terrestrial and aquatic environment. This led to the necessity of developing cost-effective, operation-convenient, and recyclable adsorbents. ZnCoFe mixed metal oxide (MMO) was synthesized using co-precipitation. The sample was characterized using X-ray powder diffraction, Fourier transform infrared spectroscopy, and scanning electron microscopy. Factors affecting the adsorption process such as pH, the dose of adsorbent, and time were investigated. ZnCoFe MMO showed the maximum adsorption capacity of 118.45 mg/g for ceftriaxone sodium. The spent MMO was recycled as an adsorbent for malachite green (MG) removal. Interestingly, the spent adsorbent showed 94% removal percent for MG as compared to the fresh MMO (90%). The kinetic investigation of the adsorption process was performed and discussed. In addition, ZnCoFe MMO was tested as an antimicrobial agent. The proposed approach opens up a new avenue for recycling wastes after adsorption into value-added materials for utilization in adsorbent production with excellent performance as antimicrobial agents.

Development of Mesopore Structure of Mixed Metal Oxide through Albumin-Templated Coprecipitation and Reconstruction of Layered Double Hydroxide

Mixed metal oxide (MMO) with relatively homogeneous mesopores was successfully obtained by calcination and reconstruction of albumin-templated layered double hydroxide (LDH). The aggregation degree of albumin-template was controlled by adjusting two different synthesis routes, coprecipitation and reconstruction. X-ray diffraction patterns and scanning electron microscopic images indicated that crystal growth of LDH was fairly limited during albumin-templated coprecipitation due to the aggregation. On the hand, crystal growth along the lateral direction was facilitated in albumin-templated reconstruction due to the homogeneous distribution of proteins moiety. Different state of albumin during LDH synthesis influenced the local disorder and porous structure of calcination product, MMO. The N₂ adsorption-desorption isotherms demonstrated that calcination on reconstructed LDH produced MMO with large specific surface area and narrow distribution of mesopores compared with calcination of coprecipitated LDH.

Magnetically separable graphene-based Ni–Fe mixed metal oxide nanocubes derived from a Prussian- blue analogue: synthesis, structure and application in oxidative degradation of bisphenol A

Mixed metal oxide (MMO) nanocubes were prepared by calcining a Ni–Fe Prussian-blue analogue (Ni–Fe PBA) and then uniformly supported on reduced graphene oxide (RGO) through a simple hydrothermal reaction instead of the commonly used etching.