A facile microwave-assisted synthesis of mesoporous hydroxyapatite as an efficient adsorbent for Pb2+ adsorption

The efficient uptake of uranium by amine-functionalized β-cyclodextrin supported fly ash composite from polluted water

A novel polyethyleneimine/polydopamine-functionalized β-cyclodextrin supported fly ash adsorbent (PEI/PDA/β-CD/FA) had been synthesized to uptake uranium from polluted water. At pH = 5.0 and T = 298 K, the uranium uptake efficiency and capacity of PEI/PDA/β-CD/FA reached to 98.7 % and 622.8 mg/g, respectively, which were much higher than those of FA (71.4 % and 206.7 mg/g).The excellent uranium uptake properties of PEI/PDA/β-CD/FA could be explained by three points: (1) using β-CD as a supporting material could effectively avoid the aggregation of FA and improve the hydrophily of FA; (2) the unique cavity structure of β-CD could form chelates with uranyl ions; (3) the formation of PEI/PDA co-deposition coating on FA further enhanced the affinity of FA to UO22+. With the presence of interfering ions, the uptake efficiency of PEI/PDA/β-CD/FA for uranium was still up to 94.5 % after five cycles, indicating the high selectively and recoverability of PEI/PDA/β-CD/FA. In terms of the results of characterizations, uranium was captured by PEI/PDA/β-CD/FA via electrostatic attraction, hydrogen bond, coordination and complexation. To sum up, PEI/PDA/β-CD/FA was expected to be used for actual sewage treatment owing to its excellent uranium uptake efficiency/capacity, selectivity, cycle stability and feasibility of actual application.

Hydroxyapatite and its composite in heavy metal decontamination: Adsorption mechanisms, challenges, and future perspective

Nanohydroxyapatite (n-HAP), recognized by its peculiar crystal architecture and distinctive attributes showcased the underlying potential in adsorbing heavy metal ions (HMI). In this paper, the intrinsic mechanism of HMI adsorption by n-HAP was first revealed. Subsequently, the selectivity and competitiveness of n-HAP for HMI in a variety of environments containing various interferences from cations, anions, and organic molecules are elucidated. Next, n-HAP was further categorized according to its morphological dimensions, and its adsorption properties and intrinsic mechanisms were investigated based on these different morphologies. It was shown that although n-HAP has excellent adsorption capacity and cost-effectiveness, its application is often challenging to realize due to its inherent fragility and agglomeration, the technical problems required for its handling, and the difficulty of recycling. Finally, to address these issues, this paper discusses the tendency of n-HAP and its hybridized/modified materials to adsorb HMI as well as the limitations of their applications. By summarizing the limitations and future directions of hybridization/modification HAP in the field of HMI contamination abatement, this paper provides insightful perspectives for its gradual improvement and rational application.

Facet-Controlled Growth of Hydroxyapatite for Effectively Removing Pb from Aqueous Solutions

To address the growing concerns regarding severe water pollution, effective and environmentally friendly adsorbents must be identified. In this study, we prepared hydroxyapatite (HAp, Ca10(PO4)6(OH)2) as an eco-friendly absorbent via simple precipitation and obtained rod- (r-HAp) and plate-shaped HAp (p-HAp). The approach to obtaining p-HAp involved a low pH titration rate, promoting growth along the c-axis due to the adsorption of OH- on the (110) facet. Conversely, r-HAp was obtained by maintaining a high concentration of OH- during the initial stage through rapid pH titration, leading to a stronger restrictive effect on the growth of positively charged a(b)-planes. p-HAp demonstrated superior adsorption capacity, removing Pb through dissolution and recrystallization, achieving an impressive 625 mg/g within a 60 min reaction time compared to r-HAp. Our findings afford insights into the Pb removal mechanisms of HAp with different morphologies and can aid in the development of water purification strategies against heavy metal contamination.

New insights into the environmental application of hybrid nanoparticles in metal contaminated agroecosystem: A review

Heavy metals (HMs) contamination in agricultural soils is a major constraint to provide safe food to society. Cultivation of food crops on these soils, channels the HMs into the food chain and causes serious human health and socioeconomic problems. Multiple conventional and non-conventional remedial options are already in practice with variable success rates, but nanotechnology has proved its success due to higher efficiency. It also led the hypothesis to use hybrid nanoparticles (HNPs) with extended benefits to remediate the HMs and supplement nutrients to enhance the crop yield in the contaminated environments. Hybrid nanoparticles are defined as exclusive chemical conjugates of inorganic and/or organic nanomaterials that are combinations of two or more organic components, two or more inorganic components, or at least one of both types of components. HNPs of different elements like essential nutrients, beneficial nutrients and carbon-based nanoparticles are used for the remediation of metals contaminated soil and the production of metal free crops. Characterizing features of HNPs including particle size, surface area, reactivity, and solubility affect the efficacy of these HNPs in the contaminated environment. Hybrid nanoparticles have great potential to remove the HMs ions from soil solution and restrict their ingress into the root tissues. Furthermore, HNPs of essential nutrients not only compete with heavy metal uptake by plants but also fulfill the need of nutrients. This review provides a comprehensive overview of the challenges associated with application of HNPs in contaminated soils, environmental implications, their remediation ability, and factors affecting their dynamics in environmental matrices.

CTAB enabled microwave-hydrothermal assisted mesoporous Zn-doped hydroxyapatite nanorods synthesis using bio-waste Nodipecten nodosus scallop for biomedical implant applications

In biomedical exploration, the predominant characteristic is synthesizing and fabricating multifunctional nanostructure with intensified biocompatibility and excellent antibacterial applications to avoid post-surgical implant failure. The objective of the current study is to examine ideal mesoporous zinc-doped hydroxyapatite (HAp) for future use in the field of biomedical research. In the present investigation, we synthesized mesoporous Zn-doped HAp nanorods with varied mole concentrations using a profound microwave hydrothermal method utilizing bio-waste Nodipecten nodosus scallop as a calcium source and CTAB as an organic modifier. Bio-waste Nodipecten nodosus scallop is a widely available cheap calcium precursor which is converted into pure and zinc-doped hydroxyapatite nanorods with the help of the microwave hydrothermal method. Different analytical techniques like spectroscopy and electron microscopy were employed to evaluate and precisely characterize the structural and morphological characteristics in synthesized pure and mesoporous Zn-doped HAp nanorods. CTAB and microwave hydrothermal methods successfully create mesoporous Zn-doped hydroxyapatite nanorods with different sizes and morphology. Mesoporous Zinc-doped HAp nanorods show excellent antibacterial activity against Klebsiella pneumoniae (MTCC 7407) and Bacillus subtilis (MTCC 1133), compared to other nanorods. ZnHAp-3 shows notable excellent results of antibacterial effect towards K. pneumoniae and B. subtilis, by exhibiting 12.36 ± 0.12 and 13.12 ± 0.16 mm zone of inhibition. Furthermore, ZnHAp-1 shows the lower zone of inhibition, while the ZnHAp-3 sample shows the highest zone of inhibition. A foremost study performed was toxicity assays to validate safe attributes of mesoporous zinc-doped HAp intensified with the proliferation function of the zebrafish model. The results reveal the non-toxic behavior of pure and mesoporous zinc-doped HAp samples. Thus, our studies provide evidence for the synthesis technique for the mesoporous zinc-doped HAp nanorods using a novel CTAB-enabled microwave hydrothermal method utilizing bio-waste Nodipecten nodosus scallop as a calcium source will be alternative affordable biocidal antibacterial materials for controlling post-surgical implant failures.

Synthesis of hydroxyapatite nanoparticles using Acacia falcata leaf extract and study of their anti-cancerous activity against cancerous mammalian cell lines

This study deals with the synthesis of hydroxyapatite nanoparticles (HAPnps) mediated by Acacia falcata leaf extract. Aggregates of needle-shaped crystalline nanostructures were confirmed by FE-SEM and TEM analysis. Well-defined rings in the SAED patterns corroborated the polycrystalline nature of the HAPnps. Individual elements present in the HAPnps were attested by the specific signals for Ca, P, and O in the EDS and XPS analyses. The distinct peaks observed in the XRD spectrum matched well with the HAP hexagonal patterns with a mean crystallite size of 55.04 nm. The FTIR study unveiled the coating of the nanoparticles with the biomolecules from Acacia falcata leaves. The suspension HAPnps exhibited polydispersity (0.446) and remarkable stability (zeta potential: - 31.9 mV) as evident from DLS studies. The pore diameter was 25.7 nm as obtained from BET analysis, suggesting their mesoporous nature. The HAPnps showed the cytotoxic effect on A549 lung and MDA-MB231 breast carcinoma cell lines, with an IC₅₀ value of 55 μg/mL. The distortion of the cell membrane and cell morphology, along with the chromatin condensation and cell necrosis on treatment with HAPnps were detected under fluorescence microscopy post acridine orange/ethidium bromide dye staining. This study reports the anti-cancerous potential of non-drug-loaded plant-mediated HAPnps. Therefore, the HAPnps obtained in this investigation could play a vital role in the biomedical field of cancer therapy.

Green synthesized hydroxyapatite nanoadsorbent for the adsorptive removal of AB113 dye for environmental applications

The present work reports the synthesis of hydroxyapatite (HAp) via the green chemistry approach by using the leaf extract of copper pod tree and its adsorptive potential to remove Acid blue 113 (AB113) dye. FESEM-EDS characterization of the synthesized HAp confirmed rod-shaped HAp with prominent Ca and P elements. The crystallinity of HAp was ascertained by XRD and thermal stability was analyzed by TGA. The colloidal suspension stability was determined as - 17.7 mV by Zeta potential analyzer. The mesoporous structure was affirmed via BET studies with a high magnitude of specific surface area. TEM studies substantiated the rod-shaped HAp as observed in FESEM. The signals specific to HAp were observed in XPS studies. Adsorption of AB113 on the synthesized HAp was examined by varying the process parameters. Batch experiments resulted in an optimum dye removal of 92.72% at a pH of 8, 1 g/L of CP-HAp nps dosage, 20 ppm AB113 concentration, 120 min contact time, 150 rpm agitation speed and at room temperature. The maximum adsorption capacity reached 120.48 mg/g. Multifarious isotherms characterized the adsorption with Freundlich isotherm (R² > 0.968) dominating Langmuir indicating multilayer adsorption. The experimental data reasonably matched pseudo-second-order kinetics with R² exceeding 0.99. Thermodynamic investigations underlined the spontaneity and exothermicity of the processes. Results showed the suitability of the HAp nanoadsorbent to remove AB113 from wastestreams.

Morphological Changes, Antibacterial Activity, and Cytotoxicity Characterization of Hydrothermally Synthesized Metal Ions-Incorporated Nanoapatites for Biomedical Application

The objective of this study was to prepare hydroxyapatite (HA) with potential antibacterial activity against gram-negative and gram-positive bacteria by incorporating different atomic ratios of Cu²⁺ (0.1–1.0%), Mg²⁺ (1.0–7.0%), and Zn²⁺ (1.0–7.0%) to theoretically replace Ca²⁺ ions during the hydrothermal synthesis of grown precipitated HA nanorods. This study highlights the role of comparing different metal ions on synthetic nanoapatite in regulating the antibacterial properties and toxicity. The comparisons between infrared spectra and between diffractograms have confirmed that metal ions do not affect the formation of HA phases. The results show that after doped Cu²⁺, Mg²⁺, and Zn²⁺ ions replace Ca²⁺, the ionic radius is almost the same, but significantly smaller than that of the original Ca²⁺ ions, and the substitution effect causes the lattice distance to change, resulting in crystal structure distortion and reducing crystallinity. The reduction in the length of the nanopatites after the incorporation of Cu²⁺, Mg²⁺, and Zn²⁺ ions confirmed that the metal ions were mainly substituted during the growth of the rod-shape nanoapatite Ca²⁺ distributed along the longitudinal site. The antibacterial results show that nanoapatite containing Cu²⁺ (0.1%), Mg²⁺ (3%), and Zn²⁺ (5–7%) has obvious and higher antibacterial activity against gram-positive bacteria Staphylococcus aureus within 2 days. The antibacterial effect against the gram-negative bacillus Escherichia coli is not as pronounced as against Staphylococcus aureus. The antibacterial effect of Cu²⁺ substituted Ca²⁺ with an atomic ratio of 0.1~1.0% is even better than that of Mg²⁺- and Zn²⁺- doped with 1~7% groups. In terms of cytotoxicity, nanoapatites with Cu²⁺ (~0.2%) exhibit cytotoxicity, whereas Mg²⁺- (1–5%) and Zn²⁺- (~1%) doped nanoapatites are biocompatible at low concentrations but become cytotoxic as ionic concentration increases. The results show that the hydrothermally synthesized nanoapatite combined with Cu²⁺ (0.2%), Mg²⁺ (3%), and Zn²⁺ (3%) exhibits low toxicity and high antibacterial activity, which provides a good prospect for bypassing antibiotics for future biomedical applications.

Adsorptive removal of Acid Blue 113 using hydroxyapatite nanoadsorbents synthesized using Peltophorum pterocarpum pod extract

The present work reports the study on the green synthesis of hydroxyapatite (HAP) nanoadsorbents using Peltophorum pterocarpum pod extract. HAP nanoadsorbents were characterized by using FESEM, EDS, TEM, XRD, FTIR, XPS, and BET analyses. The results highlighted the high purity, needle-like aggregations, and crystalline nature of the prepared HAP nanoadsorbents. The surface area was determined as 40.04 m²/g possessing mesopores that can be related to the high adsorption efficiency of the HAP for the removal of a toxic dye, - Acid Blue 113 (AB 113) from water. Central Composite Design (CCD) was used for optimizing the adsorption process, which yielded 94.59% removal efficiency at the optimum conditions (dose: 0.5 g/L, AB 113 dye concentration: 25 ppm, agitation speed: 173 rpm, and adsorption time: 120 min). The adsorption kinetics followed the pseudo-second-order model (R²:0.9996) and the equilibrium data fitted well with the Freundlich isotherm (R²:0.9924). The thermodynamic parameters indicated that the adsorption of AB 113 was a spontaneous and exothermic process. The highest adsorption capacity was determined as 153.85 mg/g, which suggested the promising role of green HAP nanoadsorbents in environmental remediation applications.

Environmental-Friendly Adsorbent Composite Based on Hydroxyapatite/Hydroxypropyl Methyl-Cellulose for Removal of Cationic Dyes from an Aqueous Solution

The aim of this study is to develop a new, efficient, and inexpensive natural-based adsorbent with high efficacy for the cationic dye methylene blue (MB). A natural-based nanocomposite based on hydroxyapatite (HAp) and hydroxypropyl methylcellulose (HPMC) was selected for this purpose. It was synthesized by the dissolution/reprecipitation method. A film with a homogeneous and smooth surface composed of nanoparticles was prepared from the nanocomposite. HPMC and HAp biopolymers were selected due to their compatibility, biodegradability, and non-toxicity. Total reflectance infrared spectroscopy (ATR-FTIR), scanning electron microscopy (SEM), and calorimetric/thermal gravimetric (DSC/TGA) analysis results revealed the existence of strong physical interaction between the composite components. Scanning electron microscopy (SEM) observations show a composite sheet with a homogenous and smooth surface, indicating excellent compatibility between HPMC and HAp in the composite. The nanocomposite was evaluated as an adsorbent for organic dyes in an aqueous solution. The effects of solution pH, initial MB concentration, composite concentration, and adsorption time on the adsorption efficiency were evaluated. The highest adsorption rate was seen as 52.0 mg of MB/g composite. The adsorption rate reached equilibrium in about 20 min. Fitting of the adsorption data to the Langmuir and Freundlich adsorption models was investigated. Results showed that the adsorption process follows the Langmuir isotherm model. The kinetic study results revealed that the adsorption process was pseudo-second-order. The herein composite is an excellent alternative for use as contemporary industrial-scale adsorbents.

Chitin/egg shell membrane@Fe3O4 nanocomposite hydrogel for efficient removal of Pb2+ from aqueous solution

The development of adsorbents by using the byproducts or waste from large-scale industrial and agricultural production is of great significance, and is considered to be an economic and efficient strategy to remove the heavy metals from polluted water. In this work, a novel chitin/EM@Fe₃O₄ nanocomposite hydrogel was obtained from a NaOH/urea aqueous system, where the proteins of egg shell membrane and Fe₃O₄ nanoparticles were chemically bonded to chitin polymer chains with the help of epichlorohydrin. Due to the existence of a large number of –NH₂, –OH, –CONH–, –COOH and hemiacetal groups, the adsorption efficiency for Pb²⁺ into the absorbent was dramatically enhanced. The experimental results revealed that the adsorption behavior strongly depends on various factors, such as initial pH, initial Pb²⁺ concentration, incubation temperature and contact time. The kinetic experiments indicated that the adsorption process for Pb²⁺ in water solution agreed with the pseudo-second-order kinetic equation. The film diffusion or chemical reaction is the rate limiting process in the initial adsorption stage, and the adsorption of Pb²⁺ into the nanocomposite hydrogel can well fit the Langmuir isotherm. Thermodynamic analysis demonstrated that such adsorption behaviors were dominated by an endothermic (ΔH° > 0) and spontaneous (ΔG° < 0) process.

A novel kind of chitin/EM@Fe₃O₄ nanocomposite hydrogel derived from the biowastes of egg shell membrane and chitin was successfully prepared for efficient removal of Pb²⁺ from wastewater solution.

Hydroxyapatite-based adsorbents: Applications in sequestering heavy metals and dyes

Hydroxyapatite (HAp) is a calcium phosphate material that was used primarily in bone regeneration and repair as a result of its chemical similarity with bone. However, HAp has emerged as a very promising adsorbent for sequestering contaminants like heavy metals, dyes, hydrocarbons as well as other emerging pollutants from wastewater as a result of its versatility and encouraging adsorptive properties. Contaminants like heavy metals and dyes have been a major source of environmental concern. Research studies involving the use of HAp as adsorbents for the adsorptive treatment of heavy metal- and dye-contaminated wastewater have become increasingly popular due to its eco-friendliness, easy synthesis, unique adsorption properties etc. Various methods are available for the synthesis of HAp and its composites with some of these methods used in combination with other methods to obtain more efficient HAp-based adsorbents. In this work, the adsorptive removal of heavy metals and dyes by HAp and its composites was extensively reviewed as well as the parametric effects of process factors like contact time, solution pH, temperature, solute concentration etc on the adsorption process. Kinetic, thermodynamic, and isotherm models for elucidating the adsorption process were also considered. Generally, from the works reviewed, HAp-based adsorbents were found to be very effective for sequestering heavy metals and dyes from solution and thus presents a low-cost option for adsorptive wastewater treatment.

Recent Progress in the Application of Hydroxyapatite for the Adsorption of Heavy Metals from Water Matrices

Wastewater treatment remains a critical issue globally, despite various technological advancements and breakthroughs. The study of different materials and technologies gained new valences in the last years, in order to obtain cheap and efficient processes, to obtain a cleaner environment for future generations. In this context, the present review paper presents the new achievements in the materials domain with highlights on apatitic materials used for decontamination of water loaded with heavy metals. The main goal of this review is to present the adsorptive removal of heavy metals using hydroxyapatite-based adsorbents, offering a general overview regarding the recent progress in this particular area. Developing the current review, an attempt has been made to give appropriate recognition to the most recent data regarding the synthesis methods and targeted pollutants, including important information regarding the synthesis methods and precursors, morphological characteristics of the adsorbent materials and effectiveness of processes.

Zinc and cadmium adsorption from wastewater using hydroxyapatite synthesized from flue gas desulfurization waste

The purpose of this work is to produce an alternative cost-effective adsorbent to remove zinc and cadmium from wastewater using hydroxyapatite (HAP) synthesized with hydrothermal method from FGD (Flue gas desulfurization) waste generated by two different coal power plants. The effects of FGD type (Cayırhan and Orhaneli) and molar ratio (H₃PO₄/CaSO₄) (0.6-4.79) on HAP synthesis were investigated. Afterwards, effects of the adsorbent dose (1-2 g/L), heavy metal concentration (30, 40, 50 mg/L) and contact time (1, 2, 3, 4 h) on zinc and cadmium adsorption yield from synthetic wastewater using produced HAP were examined. FGD waste and synthesized FGD-HAP were characterized by X-Ray Diffraction (XRD), Fourier Transformed Infrared Spectroscopy (FT-IR), Scanning Electron Microscope (SEM) and Brunauer-Emmett-Teller (BET) instruments. The zinc and cadmium concentration was studied by Inductively coupled plasma atomic emission spectroscopy (ICP-AES). Maximum zinc adsorption capacity of the Cayırhan FGD-HAP was 49.97 and 49.99 mg/L, Orhaneli FGD-HAP was 49.96 and 49.99 mg/L, for 1 g/L and 2 g/L adsorbent dose, respectively, for 50 mg/L heavy metal concentration and 4 h contact time. Maximum cadmium adsorption capacity of the Cayırhan FGD-HAP was 39.98 and 39.99 mg/L, Orhaneli FGD-HAP was 40 and 39.99 mg/L, for 1 g/L and 2 g/L adsorbent dose, respectively, for 40 mg/L heavy metal concentration and 4 h contact time. Adsorption yields were calculated between 98.53% and 100%. The adsorption data were well explained by a second-order kinetic model, and the Freundlich isotherm model fits the equilibrium data. The adsorption results demonstrated that FGD's waste is an effective source to synthesize HAP, which is used as an adsorbent for zinc and cadmium removal from wastewater due to high adsorption capacity.

Ultrasound-irradiated synthesis of 3-mercaptopropyl trimethoxysilane-modified hydroxyapatite derived from fish-scale residues followed by ultrasound-assisted organic dyes removal

We report a novel method for the synthesis of 3-mercaptopropyl trimethoxysilane-modified hydroxyapatite (FHAP-SH) derived from fish-scale residues by using ultrasound irradiation. Scanning electron microscopy, transmission electron microscopy, energy-dispersive spectroscopy, X-ray diffraction, and Fourier transform infrared spectroscopy were used for the FHAP-SH characterization. Then, the organic dye adsorption on the FHAP-SH was monitored through an ultrasound process. After the dye removal optimization, significant improvements were observed in the maximum adsorption capacities for Congo Red (CR, 500 mg g^-1), Coomassie Brilliant Blue G 250 (CB, 235 mg g^-1), and Malachite Green (MG, 625 mg g^-1). The adsorption behaviors of these dyes were fitted by using the Langmuir isotherm model with a high coefficient of determination values ranging from 0.9985 to 0.9969. The adsorption of the three dyes onto FHAP-SH was an endothermic process based on the adsorption thermodynamics model, while the adsorption kinetics analysis of the dyes presented a good alignment with the pseudo-second-order kinetics. The FHAP-SH exhibits a remarkably high adsorption capacity, is inexpensive, and fulfills the ecofriendly requirements of dye wastewater treatment, especially in the textile industry.