A tough chitosan-alginate porous hydrogel prepared by simple foaming method

Preparation of chitosan mesoporous membrane/halloysite composite for efficiently selective adsorption of Al(III) from rare earth ions solution through constructing pore structure on substrate

The removal of impurity Al(III) from rare earth ion solution by selective adsorption method was one of the challenging tasks. Herein, calcination and acid dissolution treatment were used to construct the pore structure for the halloysite substrate (Hal-650-H) and provide conditions for the formation of the chitosan mesoporous membrane to prepare composite (Hal-H-2CS). The selective adsorption properties and mechanism of the Hal-H-2CS for Al(III) in the rare earth ion solution were studied. The results showed that the formation of mesoporous structures for chitosan provided abundant sites for the adsorption of Al(III). Hal-H-2CS showed remarkable selective adsorption properties for Al(III) in a wide pH range and the binary mixtures with high content of Al(III) or La(III). The maximum adsorption capacity of Al(III) was 106 mg/g, while the adsorption capacity of La(III) was only 1.41 mg/g at pH 4.0. In addition, the Hal-H-2CS exhibited excellent regeneration and structural stability. The remarkable selective properties of Hal-H-2CS was achieved by the synergistic effect between chitosan mesoporous membrane and Hal-650-H, the main adsorption sites were the OH, NH2, CONH2 of chitosan and the oxygen sites of the Hal-650-H. This work provides a new strategy for the design and preparation of outstanding selective adsorbent for Al(III).

Wettability of HPMC/PEG/CS Thermosensitive Porous Hydrogels

Thermosensitive hydrogels have been receiving attention in the development of fire extinguishing agents due to their stimuli responsivity. Conventional hydrogels are limited by their slow response rate, and their wettability has not been studied systematically. In the present study, a concentrate of a thermosensitive porous system has been successfully synthesized by adding Na2CO3/CH3COOH as a foaming agent into the mixture of hydroxypropyl methylcellulose (HPMC)/polyethylene glycol (PEG)/chitosan (CS). The systems with different concentrations were obtained by diluting the concentrate with water. Thermosensitivity, surface tension and contact angle were characterized. In addition, spreadability, wettability and adhesivity were investigated systematically. Results showed that the systems with a concentration greater than 15 wt% exhibited outstanding performance of thermosensitivity and coagulability. A total of 20 wt% of the system has the best spreadability and wettability on the wood surface, most likely due to favorable contributions brought by both adequate viscosity and hydrophilicity. The adhesive force and surface-free energy of the pre-gel droplet that reached deposition on the wood surface decreased by 46.78% and 20.71%, respectively. The gel has a great capacity of water retention over a long period of time, which makes this porous gel the best system when it comes to its wettability and adhesiveness towards the chosen wood surface. The equilibrium surface tension decreased by 45.50% compared with water. HPMC/PEG/CS thermosensitive porous hydrogel with excellent wettability presented wide-ranging possibilities for the further development of fire suppression agents of fast phase-transition thermosensitive hydrogel.

The Diamond Concept Enigma: Recent Trends of Its Implementation in Cross-linked Chitosan-Based Scaffolds for Bone Tissue Engineering

An increasing number of publications over the past ten years have focused on the development of chitosan-based cross-linked scaffolds to regenerate bone tissue. The design of biomaterials for bone tissue engineering applications relies heavily on the ideals set forth by a polytherapy approach called the "Diamond Concept". This methodology takes into consideration the mechanical environment, scaffold properties, osteogenic and angiogenic potential of cells, and benefits of osteoinductive mediator encapsulation. The following review presents a comprehensive summarization of recent trends in chitosan-based cross-linked scaffold development within the scope of the Diamond Concept, particularly for nonload-bearing bone repair. A standardized methodology for material characterization, along with assessment of in vitro and in vivo potential for bone regeneration, is presented based on approaches in the literature, and future directions of the field are discussed.

Effect of Selected Crosslinking and Stabilization Methods on the Properties of Porous Chitosan Composites Dedicated for Medical Applications

Chitosan is one of the most commonly employed natural polymers for biomedical applications. However, in order to obtain stable chitosan biomaterials with appropriate strength properties, it is necessary to subject it to crosslinking or stabilization. Composites based on chitosan and bioglass were prepared using the lyophilization method. In the experimental design, six different methods were used to obtain stable, porous chitosan/bioglass biocomposite materials. This study compared the crosslinking/stabilization of chitosan/bioglass composites with ethanol, thermal dehydration, sodium tripolyphosphate, vanillin, genipin, and sodium β-glycerophosphate. The physicochemical, mechanical, and biological properties of the obtained materials were compared. The results showed that all the selected crosslinking methods allow the production of stable, non-cytotoxic porous composites of chitosan/bioglass. The composite with genipin stood out with the best of the compared properties, taking into account biological and mechanical characteristics. The composite stabilized with ethanol is distinct in terms of its thermal properties and swelling stability, and it also promotes cell proliferation. Regarding the specific surface area, the highest value exposes the composite stabilized by the thermal dehydration method.

Synthesis, Characterization, Properties, and Biomedical Application of Chitosan-Based Hydrogels

The prospective applications of chitosan-based hydrogels (CBHs), a category of biocompatible and biodegradable materials, in biomedical disciplines such as tissue engineering, wound healing, drug delivery, and biosensing have garnered great interest. The synthesis and characterization processes used to create CBHs play a significant role in determining their characteristics and effectiveness. The qualities of CBHs might be greatly influenced by tailoring the manufacturing method to get certain traits, including porosity, swelling, mechanical strength, and bioactivity. Additionally, characterization methods aid in gaining access to the microstructures and properties of CBHs. Herein, this review provides a comprehensive assessment of the state-of-the-art with a focus on the affiliation between particular properties and domains in biomedicine. Moreover, this review highlights the beneficial properties and wide application of stimuli-responsive CBHs. The main obstacles and prospects for the future of CBH development for biomedical applications are also covered in this review.

A Comprehensive Review on Bio-Based Materials for Chronic Diabetic Wounds

Globally, millions of people suffer from poor wound healing, which is associated with higher mortality rates and higher healthcare costs. There are several factors that can complicate the healing process of wounds, including inadequate conditions for cell migration, proliferation, and angiogenesis, microbial infections, and prolonged inflammatory responses. Current therapeutic methods have not yet been able to resolve several primary problems; therefore, their effectiveness is limited. As a result of their remarkable properties, bio-based materials have been demonstrated to have a significant impact on wound healing in recent years. In the wound microenvironment, bio-based materials can stimulate numerous cellular and molecular processes that may enhance healing by inhibiting the growth of pathogens, preventing inflammation, and stimulating angiogenesis, potentially converting a non-healing environment to an appropriately healing one. The aim of this present review article is to provide an overview of the mechanisms underlying wound healing and its pathophysiology. The development of bio-based nanomaterials for chronic diabetic wounds as well as novel methodologies for stimulating wound healing mechanisms are also discussed.

Effective Removal of Methylene Blue from Simulated Wastewater Using ZnO-Chitosan Nanocomposites: Optimization, Kinetics, and Isotherm Studies

Successful synthesis of ZnO-chitosan nanocomposites was conducted for the removal of methylene blue from an aqueous medium. Remarkable performance of the nanocomposites was demonstrated for the effective uptake of the dye, thereby achieving 83.77, 93.78 and 97.93 mg g^-1 for the chitosan, 5 wt.% ZnO-Chitosan and 10 wt.% ZnO-Chitosan, respectively. The corresponding adsorption efficiency was 88.77, 93.78 and 97.95 for the chitosan, 5 wt.% ZnO-Chitosan and 10 wt.% ZnO-Chitosan, respectively. Upon regeneration, good reusability of the nanocomposites was manifested for the continuous removal of the dye up to six consecutive cycles. The adsorption process was kinetically described by a pseudo-first order model, while the isotherms were best fitted by the Langmuir model.

One-step preparation of hydrogel based on different molecular weights of chitosan with citric acid

BACKGROUND

Chitosan-based hydrogels have been prepared previously by a two-step protocol in which chitosan was first dissolved in dilute acetic acid and then crosslinked by glutaraldehyde or genipin. This was a time-consuming method, which had the disadvantages of high costs and biological safety problems.

RESULTS

Scanning electron microscopy (SEM) results verified the successful preparation of hydrogels based on high, medium, and low molecular-weight chitosan (HCS, MCS, and LCS), respectively. The hydrogels prepared with HCS, MCS, and LCS were formed through the accumulation of different-sized crystals. The framework density of the hydrogel was enhanced by an increase in the chitosan molecular weight and exhibited a crack pore pattern composed of flake particles. Medium molecular-weight chitosan-based hydrogel exhibited the highest specific surface area and total pore volume, with values of 3.81 m² g^-1 and 0.0109 cm³ g^-1 , respectively. The water absorption rate of the chitosan based hydrogels was influenced by its molecular weights at the sequence of LCS > HCS > MCS, while the maximum compression stress was affected at the sequence of HCS > MCS > LCS. The network structure was enhanced with an increase in the chitosan molecular weight and reached maximum stress levels of 4.50, 1.50 and 0.75 MPa for HCS-, MCS-, and LCS-based hydrogels, respectively.

CONCLUSION

Citric acid was shown to be an effective dissolving and crosslinking agent in the preparation of MCS- and HCS-based hydrogels. The physiochemical properties of the hydrogels were enhanced as the molecular weight of the chitosan increased. © 2021 Society of Chemical Industry.

Fermentation-Inspired Gelatin Hydrogels with a Controllable Supermacroporous Structure and High Ductility for Wearable Flexible Sensors

Supermacroporous hydrogels have attracted wide concern due to their comfort and breathability in wearable health-monitoring applications. Size controllable supermacroporous structure and excellent mechanical properties are the most important for its application. However, they are normally fabricated by the cryogelation method, which is difficult to control pore size and maintain flexibility. Here, yeast fermentation-inspired gelatin hydrogels with a controllable supermacroporous structure and excellent mechanical properties were fabricated for the first time. The pore size can be controlled by adjusting the content of glucose and yeast, the ratio of glucose to yeast, fermentation time, and gelatin content during fermentation. The hydrogels demonstrated a controllable pore size range from 100 to 400 μm and rapid swelling characteristics. The mechanical properties were maintained by soaking ammonium sulfate solution for 12 h, showing maximum tensile and compressive strains over 300 and 99%, respectively. This novel approach can be easily applied to the preparation of supermacroporous and high ductility hydrogels under mild conditions. Furthermore, conductive hydrogels combined supermacroporous structures with conductive polyaniline and reduced oxidized graphene, and silver nanowires were prepared as wearable flexible sensors. The obtained sensors maintain well-distributed porosity, breathability, and mechanical flexibility, also showing excellent conductivity of 2.4 S m-1. Finally, the sensors were successfully applied to detect physiological signals and human-computer interaction.

3D printing and properties of cellulose nanofibrils-reinforced quince seed mucilage bio-inks

Plant-based hydrogels have attracted great attention in biomedical fields since they are biocompatible and based on natural, sustainable, cost-effective, and widely accessible sources. Here, we introduced new viscoelastic bio-inks composed of quince seed mucilage and cellulose nanofibrils (QSM/CNF) easily extruded into 3D lattice structures through direct ink writing in ambient conditions. The QSM/CNF inks enabled precise control on printing fidelity where CNF endowed objects with shape stability after freeze-drying and with suitable porosity, water uptake capacity, and mechanical strength. The compressive and elastic moduli of samples produced at the highest CNF content were both increased by ~100% (from 5.1 ± 0.2 kPa and 32 ± 1 kPa to 10.7 ± 0.5 and 64 ± 2 kPa, respectively). These values ideally matched those reported for soft tissues; accordingly, the cell compatibility of the printed samples was evaluated against HepG2 cells (human liver cancer). The results confirmed the 3D hydrogels as being non-cytotoxic and suitable to support attachment, survival, and proliferation of the cells. All in all, the newly developed inks allowed sustainable 3D bio-hydrogels fitting the requirements as scaffolds for soft tissue engineering.

Ovarian Cell Encapsulation in an Enzymatically Crosslinked Silk-Based Hydrogel with Tunable Mechanical Properties

An artificial ovary is a promising approach for preserving fertility in prepubertal girls and women who cannot undergo current cryopreservation strategies. However, this approach is in its infancy, due to the possible challenges of creating a suitable 3D matrix for encapsulating ovarian follicles and stromal cells. To maintain the ovarian stromal cell viability and proliferation, as a first step towards developing an artificial ovary, in this study, a double network hydrogel with a high water swelling capacity (swelling index 15–19) was developed, based on phenol conjugated chitosan (Cs-Ph) and silk fibroin (SF) through an enzymatic crosslinking method using horseradish peroxidase. The addition of SF (1%) to Cs (1%) decreased the storage modulus (G’) from 3500 Pa (Cs1) to 1600 Pa (Cs-SF1), and the hydrogels with a rapid gelation kinetic produced a spatially homogeneous distribution of ovarian cells that demonstrated 167% proliferation after 7 days. This new Cs-SF hydrogel benefits from the toughness and flexibility of SF, and phenolic chemistry could provide the potential microstructure for encapsulating human ovarian stromal cells.