Water purification using different waste fruit cortexes for the removal of heavy metals

Optimization of the chromium (Cr+6) reduction from waterways using chemically and bacterially treated agro-waste

Heavy metals, a major source of pollution in the environment, pose a substantial threat due to their non-biodegradability and ability to accumulate in living organisms, causing health problems. Recently, researchers have been searching for cost-effective and safe ways to remove heavy metals from polluted waterways using agricultural waste substitutes. The present study focused on the low-cost treatments for the reduction of chromium Cr+6 metal from the effluent, wherein it has been found that chemically and bacterially treated agro-waste had increased heavy metal ion adsorption capabilities. A sequential optimization of the process parameters was attempted using Plackett-Burman design (PBD) and central composite design of response surface methodology (CCD-RSM) for the maximum reduction of the chromium metal from the effluent. A total of eight parameters were screened out using a 12-run PBD experiment. Out of the eight parameters, time, HCl, NaOH, and bacterial treatments were found to be significantly affecting the maximum reduction of Cr+6 from the effluent. To investigate the interactions' effects of the chosen parameters, they were evaluated using CCD-RSM. Maximum 74% Cr+6 reduction was achieved under the optimum treatment to rice husk of HCl 4.52 N, NaOH 3.53 N, bacterial suspension 7.41%, and with an interaction time 14.32 min using 30 run CCD-RSM experiment. A scanning electron microscope was used to confirm the effects of selected variables on the agro-waste for the Cr+6 reductions, as well as a Fourier transform infrared spectrometer.

Facile synthesis of anthranilic acid based dual functionalized novel hyper cross-linked polymer for promising CO2 capture and efficient Cr3+ adsorption

A novel hyper cross-linked polymer of 2-Aminobenzoic acid (HCP-AA) is synthesized for the adsorption of Cr3+ and CO2. The Brunauer-Emmett-Teller surface area of HCP-AA is 615 m2 g-1. HCP-AA of particle size 0.5 nm showed maximum adsorption of Cr3+ for lab prepared wastewater (93%) while it was 88% for real industrial wastewater. It is might be due to electrostatic interactions, cation-π interactions, lone pair interactions and cation exchange at pH 7; contact time of 8 min; adsorbent dose 0.8 g. The adsorption capacity was calculated 52.63 mg g-1 for chromium metal ions at optimum conditions. Freundlich isotherm studies R2 = 0.9273 value is the best fit and follows pseudo second order kinetic model (R2 = 0.979). The adsorption is found non-spontaneous and exothermic through thermodynamic calculations like Gibbs free energy (ΔG), enthalpy change (ΔH) and entropy change (ΔS) were 6.58 kJ mol-1, - 60.91 kJ mol-1 and - 45.79 kJ mol-1 K-1, respectively. The CO2 adsorption capacity of HCP-AA is 1.39 mmol/g with quantity of 31.1 cm3/g (6.1 wt%) at 273Kwhile at 298 K adsorption capacity is 1.12 mmol/g with quantity 25.2 cm3/g (5 wt%). Overall, study suggests that carboxyl (-COOH) and amino (-NH2) groups may be actively enhancing the adsorption capacity of HCP-AA for Cr3+ and CO2.

Manganese dioxide decorated kiwi peel powder for efficient removal of lead from aqueous solutions, blood and Traditional Chinese Medicine extracts

For human health and environment safety, it is of great significance to develop novel materials with high effectiveness for removal of lead from not only aqueous solutions but also human body and traditional Chinese medicines. Here, functional kiwi peel composite, manganese dioxide decorated kiwi peel powder (MKPP), is proposed for the removal of Pb2+ effectively. The adsorption of Pb2+ in aqueous solution is a highly selective and endothermic process and kinetically follows a pseudo-second-order model, which can reach equilibrium with the capacity of 192.7 mg/g within 10 min. Comprehensive factors of hydration energy, charge-to-radius ratio and softness of Pb2+ make a stronger affinity between MKPP and Pb2+. The possible adsorption mechanism involves covalent bond, electrostatic force and chelation, etc. MKPP can be efficiently regenerated and reused with high adsorption efficiency after five cycles. Besides, MKPP can remove over 97% of Pb2+ from real water samples. MKPP can also alleviate lead poisoning to a certain extent and make the Pb level of TCM extract meet the safety standard. This work highlights that MKPP is a promising adsorbent for the removal of Pb2+ and provides an efficient strategy for reusing kiwi peel as well as dealing with the problem of Pb pollution.

Kiwi peel waste as a recyclable adsorbent to remove textile dyes from water: Direct Blue 78 removal and recovery

According to circular bioeconomy principles, the use of kiwi peels to remove Direct Blue 78 (DB) from water is investigated during this work, proposing food waste as a recyclable adsorbent substrate. Direct Blue 78 (DB) was adopted as a model pollutant, employing its visible spectrum to monitor its adsorption. The adsorption process was thus fully characterized, investigating the roles of ionic strength, pH values, adsorbent/pollutant amounts, and temperature. The thermodynamics, kinetics, and adsorption isotherms were also studied. To extend the kiwi peels' lifetime, quite complete desorption was obtained by adopting hot water as a safe and eco-friendly strategy. Despite the relatively low kiwi peels' maximum adsorption capacity (6 mg g-1) for DB when adsorbed in the presence of NaCl, 10 cycles of adsorption/desorption were attempted, proposing the recycling of both the dye and kiwi peels as dictated by circular economy principles. Dyeing experiments were also performed, evidencing the dye's ability to color cotton fabrics after its recycling. Finally, the removal of other textile dyes, Direct Red 83 : 1 and Direct Yellow 86, was demonstrated in a mixture with DB. A preliminary investigation was performed to find the best working conditions for inducing the solid-state dye photodegradation, proposing a possible alternative for the adsorbent regeneration.

Activated carbons from open air and microwave-assisted impregnation of cotton and neem husks efficiently decolorize neutral cotton oil

The decolorization of cottonseed oil with activated carbons (ACs) from neem and cotton husks has a dual interest: elimination of undesirable pigments in oil and valorization of the husks; by-products of neem and cottonseed processing, which would otherwise be dumped along riverbanks and farms causing environmental pollution. ACs were produced from neem and cottonseed husks after acid impregnation assisted by microwave heating and in ambient air for the decolorization of neutral cottonseed oil. The experimental data were analyzed by the intraparticle diffusion and the pseudo-second-order kinetic models as well as the Langmuir and Freundlich isotherm models. The method of impregnation and carbonization time had dramatic effects on the specific surface area (800-1500 g/m2), the quantity of burn-off (50-70 %), and methylene blue index (300-5000 mg/g) values which indicated the potential of the prepared activated carbons in the bleaching of vegetable oil and in other applications such as environmental clean-up and in agriculture. Pigment adsorption increased with temperature for all ACs indicating that the decolorization process was endothermic. The quantity of adsorbent equally had a significant effect on the pigment adsorption process for all ACs. All the activated carbons prepared in this work were 30-80 % more efficient in pigment adsorption than bleaching earth that is normally used in decolorizing neutral cotton seed oil in industries. All tested models are adequate to describe pigment adsorption by the ACs. Both methods of preparation of ACs were effective for oil decolorization, but microwave impregnation is more appealing because it requires only 1 h compared to 6 h for ambient air. Optimum decolorization conditions were 90 °C for 40min and adsorbent concentration of 2 %.

Application of conventional and emerging low-cost adsorbents as sustainable materials for removal of contaminants from water

The impact of water pollution has led to the search for cost-effective and environmentally friendly treatment processes to alleviate the associated environmental hazards. Adsorption is identified as an advanced treatment technology that offers simplicity and cheap alternatives to water treatment technologies when low-cost adsorbents such as industrial by-products, waste, and agricultural waste are utilized. The utilization of these materials as low-cost adsorbents for the treatment of drinking water will bring them some value. Several practices have been done to improve the removal efficiencies of the low-cost adsorbents in order to achieve WHO standards of drinking water quality. The paper highlights some of the synthesis routes employed for the modification of low-cost adsorbents. This updated review provides information on the different applications of low-cost adsorbents in removing pollutants and their adsorption capacities in an attempt to deploy the recent sustainable low-cost adsorbents with high removal efficiencies for water treatment. Future research should focus on the fabrication of hybrid low-cost adsorbents with multifunctional and antimicrobial properties. In addition, life cycle assessment (LCA) should be conducted to reveal the environmental burdens associated with the modification of the low-cost adsorbent to improve their removal efficiencies.

Agricultural Solid Wastes Based Adsorbent Materials in the Remediation of Heavy Metal Ions from Water and Wastewater by Adsorption: A Review

Adsorption has become the most popular and effective separation technique that is used across the water and wastewater treatment industries. However, the present research direction is focused on the development of various solid waste-based adsorbents as an alternative to costly commercial activated carbon adsorbents, which make the adsorptive separation process more effective, and on popularising the sustainable options for the remediation of pollutants. Therefore, there are a large number of reported results available on the application of raw or treated agricultural biomass-based alternatives as effective adsorbents for aqueous-phase heavy metal ion removal in batch adsorption studies. The goal of this review article was to provide a comprehensive compilation of scattered literature information and an up-to-date overview of the development of the current state of knowledge, based on various batch adsorption research papers that utilised a wide range of raw, modified, and treated agricultural solid waste biomass-based adsorbents for the adsorptive removal of aqueous-phase heavy metal ions. Metal ion pollution and its source, toxicity effects, and treatment technologies, mainly via adsorption, have been reviewed here in detail. Emphasis has been placed on the removal of heavy metal ions using a wide range of agricultural by-product-based adsorbents under various physicochemical process conditions. Information available in the literature on various important influential physicochemical process parameters, such as the metal concentration, agricultural solid waste adsorbent dose, solution pH, and solution temperature, and importantly, the adsorbent characteristics of metal ion removal, have been reviewed and critically analysed here. Finally, from the literature reviewed, future perspectives and conclusions were presented, and a few future research directions have been proposed.

Isotherms and Kinetic Studies of Copper Removal from Textile Wastewater and Aqueous Solution Using Powdered Banana Peel Waste as an Adsorbent in Batch Adsorption Systems

Heavy metals that are present in surface water and wastewater are becoming a severe environmental problem. Because of its toxicity, heavy metal removal has become the main priority for environmental concerns. Banana peels are low-cost agricultural waste that could be used for heavy metal adsorption in wastewater. The main objective of this study is to evaluate the effective powdered banana peel for the removal of copper (II) from aqueous solutions and real wastewater. The banana peels were collected from domestic waste and ground to get a particle size of 150 µm. Powdered banana peel waste adsorbent (PBPWA) contained moisture content, ash content, volatile matter, and bulk density of 3.8%, 3.5%, 37.5%, and 0.02 g/cm³, respectively. The Fourier-transform infrared spectroscopy (FTIR) results showed that the alkyne, aldehyde, and amide functional groups were dominant in the powdered banana peel surface, and the scanning electron microscope showed the morphology of the adsorbent. Physicochemical characteristics of the raw wastewater revealed that the concentration of Cu (II), Pb (II), COD, BOD5, and Cd (II) were 2.75 mg/L, 2.02 mg/L, 612.16 mg/L, 185.35 mg/L, and 0.01 mg/L, respectively. At pH 5, adsorbent dose of 2g/100 mL, initial copper (II) concentration of 80 mg/L, and contact time of 90 min, the maximum removal efficiency of synthetic wastewater was 96.8% and textile wastewater was 69.0%. The adsorption isotherm fitted well with the Langmuir isotherm model at R² = 0.99. The kinetics of copper (II) adsorption followed the second-order kinetic model better. Finally, these studies showed that banana peel bio-adsorbent is a potential adsorbent for heavy metal removal from synthetic and textile wastewater.

Removal of chromium (VI) from aqueous environments using composites of polyaniline-cherry leaves

Composites of Polyaniline (PANI)-prune, peach, cherry, grape, fig and walnut leaves were synthesized under various conditions and were used to remove chromium (VI) from aqueous environments in discontinuous experiments. The results showed that the highest percentage of Cr (VI) removal (40.3%) belonged to the composite consisting of cherry leaves and PANI. Synthesis conditions of this composite were then studied to increase Cr (VI) removal. The results of the experiment on the various solvents are used in the synthesis of the composite of PANI-cherry leaves indicated that the best solvent (with 40.93% Crn(VI) removal) was water. The effects of polyvinyl alcohol (PVA) and polyethylene glycol (PEG) as additives on the synthesis of the composite PANI-cherry leaves were studied and it was revealed that the best-synthesized composite (with 51.64% Cr removal) was produced in presence of PVA (2 g/L), and the optimum pH and contact time were 2 and 30 min, respectively. Moreover, the adsorption process followed Langmuir and Freundlich adsorption isotherms, and the maximum Cr adsorption capacity was 33.01 mg/g. The results of the FTIR and XRD tests and SEM images for this composite were studied. The SEM images demonstrated that the addition of PVA reduced the size of the particles and made them more uniform. The XRD test indicated that the synthesized composite was amorphous, and the FTIR test confirmed the synthesis of the composite.

Removal of Pb2+, CrT, and Hg2+ Ions from Aqueous Solutions Using Amino-Functionalized Magnetic Nanoparticles

In this paper, a circular economy approach with the adsorption and desorption of heavy metal (HM) ions—i.e., lead (Pb2+), chromium (CrT), and mercury (Hg2+)—from aqueous solutions was studied. Specific and selective binding of HM ions was performed on stabilized and amino-functionalized iron oxide magnetic nanoparticles (γ-Fe2O3@NH2 NPs) from an aqueous solution at pH 4 and 7. For this purpose, γ-Fe2O3@NH2 NPs were characterized by thermogravimetric analysis (TGA), Fourier-transform infrared spectroscopy (FTIR), specific surface area (BET), transmission electron microscopy (TEM), EDXS, and zeta potential measurements (ζ). The effects of different adsorbent amounts (mads = 20/45/90 mg) and the type of anions (NO3−, Cl−, SO42−) on adsorption efficiency were also tested. The desorption was performed with 0.1 M HNO3. The results showed improvement of adsorption efficiency for CrT, Pb2+, and Hg2+ ions at pH 7 by 45 mg of g-Fe2O3@NH2 NPs, and the sequence was as follows: CrT > Hg2+ > Pb2+, with adsorption capacities of 90.4 mg/g, 85.6 mg/g, and 83.6 mg/g, respectively. The desorption results showed the possibility for the reuse of γ-Fe2O3@NH2 NPs with HNO3, as the desorption efficiency was 100% for Hg2+ ions, 96.7% for CrT, and 91.3% for Pb2+.

Regenerable Kiwi Peels as an Adsorbent to Remove and Reuse the Emerging Pollutant Propranolol from Water

This work aims to characterize the adsorption process of propranolol HCl, an emerging pollutant and a widely used β-blocker, onto kiwi peels, an agricultural waste. The use of UV-vis spectroscopy was considered to obtain information about the pollutant removal working in the in-batch mode. In a relatively short time, the adsorption process could remove the pollutant from water. A kiwi peel maximum adsorption capacity of 2 mg/g was obtained. With the perspective of scaling up the process, preliminary in-flux measurements were also performed. The investigation of the whole in-batch adsorption process was conducted by studying the effect of ionic strength (adopting salt concentrations from 0 to 0.4 M), pH values (from 2 to 12), adsorbent/pollutant amounts (from 25 to 100 mg and from 7.5 to 15 mg/L, respectively), and temperature values (from 289 to 305 K). The thermodynamics, the adsorption isotherms, and the kinetics of the adsorption process were also carefully investigated. The Langmuir model fitted the experimental data well, with an R2 of 0.9912, restituting KL: 1 L/mg and Q0: 1.8 mg/g. The temperature increase enhanced the pollutant removal due to the endothermic adsorption characteristics. Accordingly, a ΔH°298K of +70 KJ/mol was obtained. The pseudo-first-order kinetic model described the process. Due to the results observed during the study of the effects of pH and ionic strength, the prominent presence of electrostatic interactions, working in synergy with hydrophobic forces and H-bonds between the pollutant and kiwi peel surfaces, was successfully demonstrated. In particular, FTIR-ATR measurements confirmed the latter findings. Finally, desorption experiments for recycling 100% of propranolol for each cycle were performed using 0.1 M MgCl2. Ten cycles of adsorption/desorption were obtained and indicated that the percentage of propranolol removal was not affected during each run, increasing the maximum adsorption from 2 to 20 mg/g.

Six fruit and vegetable peel beads for the simultaneous removal of heavy metals by biosorption

In this study, a comparison between the biosorption performance of six fruit and vegetable peels, namely kiwifruit (KP), apple, banana, cucumber, orange and potato immobilized on sodium alginate beads has been made. Inductively coupled plasma coupled with mass spectroscopy was used for measuring the concentration of metal ions in solution before and after biosorption. A range of kinetic models were also applied to the biosorption batch data. The results showed that biosorption percentage of the ions were different on the various beads. For example, the decreasing order of biosorption by one KP bead at equilibrium was Cd > Cu > Hg > Ni > Pb > Cr > As, with approximately 92%, 84%, 80%, 75%, 67%, 34%, and 17% simultaneous removal of ions, respectively. The fastest biosorption was seen with Cd and Pb, as both reached equilibrium by 24 h. Equilibrium time of all other ions occurred by 48 h. While all beads in their unmodified form were suitable for the removal of divalent cations, KP bead showed significantly higher removal of the anion hexavalent Cr. Biosorption of Cd, Hg and Ni was limited by both pseudo-first order and pseudo-second order reaction rates. For Cr and Cu, the reaction was controlled by film diffusion and pseudo-first order rates. At a higher solution concentration, the preference of ions biosorbed as well as their percentage removed changed. Overall, the results indicated that KP beads show promise as a cost-effective method for removing toxic ions by biosorption, especially hexavalent chromium from drinking water.

Fruit Peels as a Sustainable Waste for the Biosorption of Heavy Metals in Wastewater: A Review

One of the environmental challenges that is currently negatively affecting the ecosystem is the continuous discharge of untreated industrial waste into both water sources and soils. For this reason, one of the objectives of this qualitative study of exploratory-descriptive scope was the review of scientific articles in different databases-Scopus, Web of Science, and Science Direct-published from 2010 to 2021 on the use of fruit peels as a sustainable waste in the removal of heavy metals present in industrial wastewater. For the selection of articles, the authors used the PRISMA guide as a basis, with which 210 publications were found and 93 were compiled. Considering the reported work, a content analysis was carried out using NVivo 12 Plus and VOSviewer 1.6.17 software. The results show that the fruits mentioned in these publications are lemon, banana, mango, tree tomato, pineapple, passion fruit, orange, coconut, avocado, apple, lulo, and tangerine. However, no studies were found with lulo and tree tomato peels. On the other hand, the heavy metals removed with the selected fruit peels were Pb+2, Cr+3, Cr+6, Ni+2, Cd+2, As+5, Cu+2, and Zn+2.

Development and Characterization of Bioadsorbents Derived from Different Agricultural Wastes for Water Reclamation: A Review

The presence of dangerous pollutants in different water sources has restricted the availability of this natural resource. Thus, the development of new low-cost and environmentally-friendly technologies is currently required to ensure access to clean water. Various approaches to the recovery of contaminated water have been considered, including the generation of biomaterials with adsorption capacity for dangerous compounds. Research on bioadsorbents has boomed in recent years, as they constitute one of the most sustainable options for water treatment thanks to their abundance and high cellulose content. Thanks to the vast amount of information published to date, the present review addresses the current status of different biosorbents and the principal processes and characterization methods involved, focusing on base biomaterials such as fruits and vegetables, grains and seeds, and herbage and forage. In comparison to other reviews, this work reports more than 60 adsorbents obtained from agricultural wastes. The removal efficiencies and/or maximum adsorption capacities for heavy metals, industrial contaminants, nutrients and pharmaceuticals are presented as well. In addition to the valuable information provided in the literature investigation, challenges and perspectives concerning the implementation of bioadsorbents are discussed in order to comprehensively guide selection of the most suitable biomaterials according to the target contaminant and the available biowastes.

Pitahaya Fruit (Hylocereus spp.) Peels Evaluation for Removal of Pb(II), Cd(II), Co(II), and Ni(II) from the Waters

The present study investigated the performance of Pitahaya (Hylocereus spp.) peel (PP) as a low-cost biosorbent in the removal of Co(II), Cd(II), Pb(II), and Ni(II) from single and multi-component solutions. The characterization of the samples was carried out by pHpzc, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS). Biosorption was carried out by batch experimental procedure to examine the effects of contact time, solution pH, initial concentration of metal ions, and biosorbent dosage. The results indicate that the biosorption of Pb(II), Cd(II), Co(II), and Ni(II) Pitahaya peels followed pseudo-second-order kinetics, and equilibrium adsorption followed the Langmuir model. The maximum sorption capacities of PP for the metallic species were found to be as follows: Pb (82.64 mg g−1) > Cd (17.95 mg g−1) > Co (6.013 mg g−1) > Ni (5.322 mg g−1). However, the efficiency of the biosorption change when the metallic species are mixed. The re-generation of the PP after the adsorption of the metallic species was done using 0.1 M HNO3 solution, and the reusability of the biomass was carried out using two adsorption and desorption cycles.

Potential Use of Biochar in Pit Latrines as a Faecal Sludge Management Strategy to Reduce Water Resource Contaminations: A Review

Faecal sludge management (FSM) in most developing countries is still insufficient. Sanitation challenges within the sub-Saharan region have led to recurring epidemics of water- and sanitation-related diseases. The use of pit latrines has been recognised as an option for on-site sanitation purposes. However, there is also concern that pit latrine leachates may cause harm to human and ecological health. Integrated approaches for improved access to water and sanitation through proper faecal sludge management are needed to address these issues. Biochar a carbon-rich adsorbent produced from any organic biomass when integrated with soil can potentially reduce contamination. The incorporation of biochar in FSM studies has numerous benefits in the control of prospective contaminants (i.e., heavy metals and inorganic and organic pollutants). This review paper evaluated the potential use of biochar in FSM. It was shown from the reviewed articles that biochar is a viable option for faecal sludge management because of its ability to bind contaminants. Challenges and possible sustainable ways to incorporate biochar in pit latrine sludge management were also illustrated. Biochar use as a low-cost adsorbent in wastewater contaminant mitigation can improve the quality of water resources. Biochar-amended sludge can also be repurposed as a useful economical by-product.

Investigation of the Conditions for Preconcentration of Cadmium Ions by Solid Phase Extraction Method Using Modified Juglans regia L. Shells

BACKGROUND

Juglans regia L. shells as agricultural waste can be considered as alternative sorbents to minimize the problems associated with heavy metal pollution.

OBJECTIVE

In this study, J. regia shells (JRS) and JRS modified with hydrazine hydrate (JRS-HH) were used as sorbents and compared for the preconcentration of Cd(II) ions from aqueous solution.

METHODS

For the characterization of sorbents, scanning electron microscopy and energy dispersive X-ray (SEM/EDX) analysis and Fourier transform infrared (FTIR) spectroscopy were used. For preconcentration, the solid phase extraction (SPE) technique was used. Preconcentration studies were performed by column method and pH, eluent type and concentration, sample volume, flow rate, and interfering ions effect were studied to determine the optimum column parameters.

RESULTS

The limit of detection (LOD) of the sorbents (JRS and JRS-HH) are 0.31 and 0.18 µg/L, respectively. According to the Langmuir isotherm model for both sorbents, for JRS KL = 0.030 L/mg, R2 = 0.992, 0.016 L/mg, and for JRS-HH KL = 0.016 L/mg, R2 = 0.998 and maximum adsorption capacities of the sorbents were found to be as 29.6 and 65.7 mg/g, respectively. The mean recoveries and RSD values at a 95% confidence level (N = 6) for Cd(II) were 100.9% and 3.42, and 100.6% and 3.79, for the JRS and JRS-HH sorbents, respectively.

CONCLUSIONS

Using this method good results were obtained when compared with those in the literature and the proposed method was successfully applied to the analysis of the certificated reference material (NIST 1640).

HIGHLIGHTS

JRS are an effective and inexpensive sorbent for the preconcentration of metal ions when modified. Thus, low-cost agricultural wastes are both recovered and have an economic value.

Development of the basics of complex technology for capturing and disposing of heavy metals from surface drains of cities

For the first time, the basics of waste-free technology for capturing heavy metal ions from urban surface runoff from residential areas of the city with the final utilization of the regenerate were developed. The technology eliminates the subsequent contamination of the lithosphere and atmosphere by regeneration products. The expediency of using fibrous chemosorbents (cationic and polyampholyte) for capturing heavy metal ions from urban surface runoff of residential areas of megalopolises has been justified because of possibility of recycling heavy metal ions and regenerating the sorbent. Model solutions of Fe, Cu, Zn, Pb salts, as well as samples of solutions of real surface effluents were studied. Small experimental samples of filters of various designs were designed and manufactured. The filters were tested at a functioning treatment facility. It was demonstrated that the content of Fe³⁺, Cu²⁺, Zn²⁺, and Pb²⁺ ions in real surface effluents decreased by 1.4-7 times after passing the effluents even through these small experimental filters. The expediency and possibility of recycling the regenerate as inorganic pigments for the paint industry is shown.

Highly sensitive determination of heavy metals in water prior to and after remediation using Citrofortunella Microcarpa

A highly sensitive bismuth/silver nanoparticles/Nafion-modified screen-printed graphene electrode was fabricated and was utilized for the detection of trace lead (Pb) concentrations in river water samples prior to and after remediation using calamansi (Citrofortunella Microcarpa) rinds in different forms viz., ground sun-dried, dry-ashed, food-grade pectin, fractionated pectin, and alcohol insoluble solids-extracted pectin. All these forms of pectin remediated Pb in the water samples. Hence, this novel method of using calamansi rinds in different forms is an effective method for the removal of lead in water. The electrode was characterized using scanning electron microscopy and energy dispersive x-ray spectrometry which confirmed the presence of the modifiers on the electrode surface. The limit of detection of 267.6 ppt and the strong linear relationship between the Pb concentration and the anodic current response (R2 = 0.999) were obtained under optimized experimental conditions and parameters.

Utilización de subproductos agroindustriales para la bioadsorción de metales pesados

La contaminación por metales pesados es un problema que afecta a los ambientes acuáticos y terrestres, y cuya principal fuente son las actividades antrópicas. Para atender este problema, la comunidad científica ha desarrollado métodos físico-químicos para la remoción de metales pesados en efluentes contaminados: sin embargo, la mayoría no son económicamente favorables, ya que presentan elevados costos de operación y mantenimiento, además de que algunos generan residuos difíciles de manejar. Sin embargo, existe un método de bajo costo, altamente eficiente y sin formación de contaminantes secundarios, denominado bioadsorción. La bioadsorción utiliza subproductos agroindustriales con el objetivo de utilizar la excesiva generación de estos residuos como bioadsorbentes, para la remoción de metales pesados en aguas residuales. La utilización de subproductos agroindustriales como bioadsorbentes ha mostrado ser una alternativa para su aprovechamiento, consecuentemente, México tiene potencial en la producción de bioadsorbentes. El objetivo de esta revisión es proporcionar información sistematizada del método de remoción de metales pesados por bioadsorción a través del uso de subproductos agroindustriales.

Inexpensive Organic Materials and Their Applications towards Heavy Metal Attenuation in Waters from Southern Peru

There is interest in using locally available, low cost organic materials to attenuate heavy metals such as Cd, Cr, Cu, Hg, Ni, Pb, and Zn found in surface waters in Peru and other developing regions. Here we mesh Spanish language publications, archived theses, and prior globally available literature to provide a tabulated synthesis of organic materials that hold promise for this application in the developing world. In total, nearly 200 materials were grouped into source categories such as algae and seashells, bacteria and fungi, terrestrial plant-derived materials, and other agricultural and processing materials. This curation was complemented by an assessment of removal potential that can serve as a resource for future studies. We also identified a subset of Peruvian materials that hold particular promise for further investigation, including seashell-based mixed media, fungal blends, lignocellulose-based substrates including sawdust, corn and rice husks, and food residuals including peels from potatoes and avocadoes. Many studies reported percent removal and/or lacked consistent protocols for solid to liquid ratios and defined aqueous concentrations, which limits direct application. However, they hold value as an initial screening methodology informed by local knowledge and insights that could enable adoption for agriculture and other non-potable water reuse applications. While underlying removal mechanisms were presumed to rely on sorptive processes, this should be confirmed in promising materials with subsequent experimentation to quantify active sites and capacities by generating sorption isotherms with a focus on environmental conditions and specific contaminated water properties (pH, temperature, ionic strength, etc.). These organics also hold promise for the pairing of sorption to indirect microbial respiratory processes such as biogenic sulfide complexation. Conversely, there is a need to quantify unwanted contaminant release that could include soluble organic matter and nutrients. In addition to local availability and treatment efficacy, social, technical, economic, and environmental applicability of those materials for large-scale application must be considered to further refine material selection.

Removal of heavy metals from industrial sludge with new plant-based washing agents

Washing is one of the techniques for permanent removal of heavy metals from industrial sludge, for which washing agents are a key influence factor. However, high-efficiency, eco-friendly, and inexpensive agents are still lacking. In this study, the solutions derived from the three plant materials including Fatsia japonica, Hovenia acerba and Pterocarya stenoptera were employed to remove Cd, Cu, Pb, and Ni from industrial sludge. The effects of washing solution concentration, pH, washing time and temperature on metal removal were investigated. The metal removal efficiencies were found to increase with increasing solution concentrations or washing temperatures, decline with increasing pH, and presented various trends with increasing washing time. Among the three agents that derived from H. acerba showed relatively high removal for Cu (75.81%), Pb (63.42%), Ni (27.52%), and Cd (56.99%). After washing, environmental risks of residual metals were markedly diminished in sludge, attributable to decrease in their exchangeable forms. Furthermore, the applications of the plant washing agents increased sludge organic carbon, alkali-hydrolysable nitrogen, available phosphorus, and available potassium. Fourier transform infrared spectroscopy analysis suggested that the hydroxyl, carboxyl, ether, and amide may be the main functional groups in the three plant materials binding the heavy metals. Overall, the agent derived from H. acerba appears to be a feasible washing material for heavy metals removal from sludge.

Adsorption of Chromium(VI) onto Freshwater Snail Shell-Derived Biosorbent from Aqueous Solutions: Equilibrium, Kinetics, and Thermodynamics

In this study, freshwater snail shells (FSSs) containing CaCO3 were used as a low-cost biosorbent for removing Cr(VI) from aqueous solutions. The characteristics of FSS and mechanism of Cr(VI) adsorption onto FSS were investigated. The FSS biosorbent was characterized using nitrogen adsorption/desorption isotherm, X-ray diffraction, scanning electron microscopy with energy dispersive spectroscopy, and Fourier transform infrared spectroscopy. The adsorption mechanism was determined by conducting various batch adsorption experiments along with fitting experimental data with various adsorption models. Batch adsorption experiments were conducted as a function of solution pH, contact time, biosorbent dose, and initial Cr(VI) concentration. Results indicated that pH = 2, a contact time of 120 min, and an initial Cr(VI) concentration of 30 mg/L at 20°C were the best conditions for adsorption of Cr(VI) onto FSS. The Cr(VI) adsorption onto FSS decreased with an increase in temperature from 20 to 40°C. The obtained maximum adsorption capacity was 8.85 mg/g for 2 g/L of FSS dose with 30 mg/L of initial Cr(VI) at 20°C. The adsorption equilibrium data fit well with the Sips and Langmuir isotherm models at 20°C with a high R2 of 0.981 and 0.975, respectively. Also, a good correlation between the experimental data and the pseudo-second-order model was achieved, with the highest R2 of 0.995 at 20°C. The adsorption mechanisms were electrostatic interaction and ion exchange. Simultaneously, this mechanism was also controlled by film diffusion. The Cr(VI) adsorption process was irreversible, spontaneous (−∆G°), exothermic (∆H° is negative), and less random (∆S° is negative). In conclusion, freshwater snail shells have the potential as a renewable adsorbent to remove toxic metals from wastewater.

Decomplexation of electroplating wastewater by ozone-based advanced oxidation process

Heavy metal contamination from electroplating wastewater is a serious risk to terrestrial life and public health. The complexed metal cannot be effectively removed by traditional precipitation without decomplexing. In this work, four ozone-based advanced oxidation processes, O₃, O₃/H₂O₂, O₃/UV and O₃/H₂O₂/UV to decomplex electroplating wastewater were investigated and their performance compared. Ethylenediaminetetraacetic acid (EDTA) and citric acid are the most common components of electroplating wastewater. They were used as representatives to study the decomplexation and mineralization of complexes in the ozone-based advanced oxidation processes. Among all, the highest degradation and mineralization efficiency of EDTA occurred in O₃/UV and was 65% and 53% in 60 min, respectively. For citric acid, the highest degradation (77%) and mineralization (56%) efficiency was observed in the O₃/H₂O₂/UV process. This indicates that selection of the advanced oxidation process is determined by the target contaminant.

Study on Adsorption of Cu and Ba from Aqueous Solutions Using Nanoparticles of Origanum (OR) and Lavandula (LV)

Wild herbs (Origanum (OR) and Lavandula (LV)) were used as environment-friendly adsorbents in this study. The adsorbents were used for adsorption of Cu and Ba from water. The adsorption of heavy metals onto OR and LV was dependent on particle size, dose, and solution pH. The diameter of adsorbent particles was less than 282.8 nm. The adsorption follows second-order kinetics. Langmuir and Freundlich models have been applied to describe the equilibrium data, and the thermodynamic parameters, the Gibbs free energy, ∆G°, enthalpy, ∆H°, and entropy, ∆S°, have been determined. The positive value of ∆H° suggests that the adsorption of heavy metals by the wild herbs is endothermic. The negative values of ∆G° at all the studied temperatures indicate that the adsorption is a spontaneous process. It can be concluded that OR and LV are promising adsorbents for the removal of heavy metals from aqueous solutions over a range of concentrations.

Evaluation of Cd(II) Ion Removal from Aqueous Solution by a Low-Cost Adsorbent Prepared from White Yam (Dioscorea rotundata) Waste Using Batch Sorption

An agricultural residue, white yam (Dioscorea rotundata) tuber peel (YTBS), was used for the removal of Cd(II) ion from an aqueous solution using a batch method. The adsorbent was characterized using FTIR, TGA, SEM, EDX, N2 BET, XRD, and XRF. The optimization of sorption variables such as pH, contact time, adsorbent dose, and initial metal ion concentration at 25 °C were also carried out. The results indicated the dependence of sorption on the adsorbate pH and adsorbent dose, while the adsorption system reached equilibrium in 180 min. The sorption kinetics was fitted to three models (pseudo first order, pseudo second order, and Elovich) to validate the kinetics, and the pseudo first order was the best model for the description of Cd(II) uptake. Equilibrium isotherm modelling was also carried out using the Langmuir, Freundlich, and Temkin models, with the Langmuir isotherm giving the best fitting to the experimental results. The maximum loading capacity (qmax) of the adsorbent for Cd(II) obtained from the Langmuir isotherm model was 22.4 mg∙g−1 with an isotherm constant (KL) of 3.46 × 10−3 L·mg−1 and r2 value of 0.99. This result indicates that the YTBS residue was a good adsorbent for the removal of Cd(II) ion from aqueous system.

Titanium Pyrophosphate for Removal of Trivalent Heavy Metals and Actinides Simulated by Retention of Europium

This work addresses the synthesis of titanium pyrophosphate, as well as the characterization and evaluation of the sorption process of europium, for removal of trivalent heavy metals and actinides simulate. The evaluation of the surface properties of titanium pyrophosphate was carried out determining the surface roughness and surface acidity constants. The values obtained from the determination of the surface roughness of the synthesized solid indicate that the surface of the material presents itself as slightly smooth. The FITEQL program was used to fit the experimental titration curves to obtain the surface acidity constants: log⁡K⁺ = 3.59 ± 0.06 and log⁡K^- = -3.90 ± 0.05. The results of sorption kinetics evidenced that the pseudo-order model explains the retention process of europium, in which the initial sorption velocity was 8.3 × 10^-4 mg g^-1 min^-1 and kinetic constant was 1.8 × 10^-3g mg min^-1. The maximum sorption capacity was 0.6 mg g^-1. The results obtained from sorption edge showed the existence of two bidentate complexes on the surface.

Pb(II) Removal Process in a Packed Column System with Xanthation-Modified Deoiled Allspice Husk

The present research dealt with lead removal using modified Pimenta dioica L. Merrill as biosorbent in a batch and in continuous flow column systems, respectively. The allspice husk residues were modified first with a treatment through the xanthation reaction. For the adsorption tests, the atomic adsorption spectrophotometry method was used to determine the lead concentrations in the liquid samples. In the kinetic batch study (10 mg of sorbent in 10 mL of 25 mg L−1 lead solution), the removal efficiency was 99% (adsorption capacity of 25.8 mg g−1). The kinetic data followed the pseudo-second-order model. The adsorption isotherm was fitted to the Freundlich model, where constants were Kf and 1/n (8.06 mg(1-1/n) g−1 L1/n and 0.52), corresponding to adsorption capacities of 8 and 62 mg g−1, at liquid equilibrium concentration of 1 and 50 mg L−1, respectively. In the continuous flow systems where lead solution of 50 mg L−1 was treated in 2 columns of 5 cm (4.45 g) and 10 cm (9.07 g) bed heights, the dynamic adsorption capacity obtained by fitting the Thomas model was 29.114 mg g−1 and 45.322 mg g−1, respectively.