Physical and antimicrobial properties of chitosan films incorporated with lauric arginate, cinnamon oil, and ethylenediaminetetraacetate

Effects of benzalkonium chloride as a cationic surfactant on the physicochemical properties of adlay millet starch films

The effects of benzalkonium chloride (BC) as a cationic surfactant on the mechanical, water barrier, microstructural, and thermal properties of adlay millet starch (AS) films were investigated in this study. With increasing BC concentration, tensile strength (from 5.93 to 6.15 MPa) and elongation at break (from 41.39 to 45.48%) of AS-BC films significantly increased, whereas their moisture content, water solubility, and water vapor permeability were reduced, indicating water resistance improvement. Fourier transform infrared spectroscopy and scanning electron microscopy analysis showed that BC at concentrations below 1% did not cause noticeable changes in the microstructure of AS-BC films. In addition, the thermal stability of AS-BC films was not affected by BC, indicating good miscibility between AS and BC. Therefore, BC could improve the physicochemical properties of starch films, and AS-BC films developed in this study can be applied as novel biodegradable packaging materials in the food packaging industry.

Supplementary Information

The online version contains supplementary material available at 10.1007/s10068-023-01383-1.

Preparation of chitosan/Enoki mushroom foot polysaccharide composite cling film and its application in blueberry preservation

In this study, the composite cling film was prepared by solution casting method using chitosan and golden mushroom foot polysaccharide as substrates, and the structure and physicochemical indexes of the composite cling film were characterized by Fourier infrared spectroscopy, X-ray diffraction, and scanning electron microscopy. The results showed that compared with single chitosan film, the composite cling film has better mechanical properties and antioxidant properties, and the barrier of UV light and water vapor is also stronger. Due to its high nutritional value, blueberry has a short shelf life due to its thin skin and poor storage resistance. Therefore, in this study, blueberry was used as the object of freshness preservation, and the single chitosan film group and the uncovered group were used as controls, and the weight loss, total bacterial colony, decay rate, respiration intensity, malondialdehyde content, hardness, soluble solids, titratable acid, anthocyanin content, and VC content of blueberry were used as freshness preservation indexes for experiments. The comprehensive results showed that the freshness preservation effect of the composite film group was significantly higher than that of the control group, with better antibacterial properties, antioxidant properties, etc., which could effectively delay fruit decay and deterioration, thus prolonging the shelf life, and thus the chitosan/Enoki mushroom foot polysaccharide composite preservation film has a high potential as a new freshness preservation material for blueberry.

Edible/Biodegradable Packaging with the Addition of Spent Coffee Grounds Oil

BACKGROUND

Following petroleum, coffee ranks as the second most extensively exchanged commodity worldwide. The definition of spent coffee ground (SCG) can be outlined as the waste generated after consuming coffee. The aims of the study are to produce edible/biodegradable packaging with the addition of spent coffee grounds (SCG) oil and to investigate how this fortification can affect chemical, textural, and solubility properties of experimentally produced films.

METHODS

The produced films were based on κ-carrageenan and pouring-drying techniques in petri dishes. Two types of emulsifiers were used: Tween 20 and Tween 80. The films were analyzed by antioxidant and textural analysis, and their solubility was also tested.

RESULTS

Edible/biodegradable packaging samples produced with the addition of SCG oil showed higher (p < 0.05) antioxidant capacity in comparison with control samples produced without the addition of SCG oil. The results of the research showed that the fortification of edible/biodegradable packaging with the addition of SCG oil changed significantly (p < 0.05) both chemical and physical properties of the films.

CONCLUSIONS

Based on the findings obtained, it was indicated that films manufactured utilizing SCG oil possess considerable potential to serve as an effective and promising material for active food packaging purposes.

Waste Orange Peels as a Source of Cellulose Nanocrystals and Their Use for the Development of Nanocomposite Films

To date, approximately 30-50% of food is wasted from post-harvesting to consumer usage. Typical examples of food by-products are fruit peels and pomace, seeds, and others. A large part of these matrices is still discarded in landfills, while a small portion is valorized for bioprocessing. In this context, a feasible strategy to valorize food by-products consists of their use for the production of bioactive compounds and nanofillers, which can be further used to functionalize biobased packaging materials. The focus of this research was to create an efficient methodology for the extraction of cellulose from leftover orange peel after juice processing and for its conversion into cellulose nanocrystals (CNCs) for use in bionanocomposite films for packaging materials. Orange CNCs were characterized by TEM and XRD analyses and added as reinforcing agents into chitosan/hydroxypropyl methylcellulose (CS/HPMC) films enriched with lauroyl arginate ethyl (LAE). It was evaluated how CNCs and LAE affected the technical and functional characteristics of CS/HPMC films. CNCs revealed needle-like shapes with an aspect ratio of 12.5, and average length and width of 500 nm and 40 nm, respectively. Scanning electron microscopy and infrared spectroscopy confirmed the high compatibility of the CS/HPMC blend with CNCs and LAE. The inclusion of CNCs increased the films' tensile strength, light barrier, and water vapor barrier properties while reducing their water solubility. The addition of LAE improved the films' flexibility and gave them biocidal efficacy against the main bacterial pathogens that cause foodborne illness, such as Escherichia coli, Pseudomonas fluorescens, Listeria monocytogenes, and Salmonella enterica.

Dual-Grafting of Microcrystalline Cellulose by Tea Polyphenols and Cationic ε-Polylysine to Tailor a Structured Antimicrobial Soy-Based Emulsion for 3D Printing

An imperative processing way to produce 3D printed structures with enhanced multifunctional properties is printing inks in the form of a gel-like colloidal emulsion. The surface-modified microcrystalline cellulose (MCC) is an excipient of outstanding merit as a particulate emulsifier to manufacture a stable Pickering emulsion gel. The tuning of the MCC structure by cationic antimicrobial compounds, such as ε-polylysine (ε-PL), can offer a surface activity with an antimicrobial effect. However, the MCC/ε-PL lacks the appropriate emulsifying ability due to the development of electrostatic complexes. To overcome this challenge, (i) a surface-active MCC conjugate was synthesized by a sustainable dual-grafting technique (ii) to produce a highly stable therapeutic soy-based Pickering emulsion gel (iii) for potential application in 3D printing. In this regard, the tea polyphenols were initially introduced into MCC by the free-radical grafting method to decrease the charge density of anionic MCC. Then, the antioxidative MCC-g-tea polyphenols were reacted by ε-PL to produce a dual-grafted therapeutic MCC conjugate (micro-biosurfactant), stabilizing the soy-based emulsion system. The results indicated that the dual-grafted micro-biosurfactant formed a viscoelastic and thixotropic soy-based emulsion gel with reduced droplet size and long-term stability. Besides, there was an improvement in the interfacial adsorption features of soy-protein particles after micro-biosurfactant incorporation, where the interfacial pressure and surface dilatational viscoelastic moduli were enhanced. Consequently, it was revealed that the therapeutic Pickering emulsion gel was more suitable to manufacture a well-defined 3D architecture with high resolution and retained permanent deformation after unloading (i.e., a recoverable matrix). This work established that the modification of the MCC backbone by tea polyphenols and ε-PL advances its bioactive properties and emulsifying performance, which finally obtains a soy-based 3D printed structure with noteworthy mechanical strength.

A Promising Therapeutic Soy-Based Pickering Emulsion Gel Stabilized by a Multifunctional Microcrystalline Cellulose: Application in 3D Food Printing

The feasible application of additive manufacturing in the food and pharmaceutical industries strongly depends on the development of highly stable inks with bioactive properties. Surface-modified microcrystalline cellulose (MCC) shows the potential of being a useful particulate (i.e., Pickering)-type emulsifier to stabilize emulsions. To attain desired therapeutic properties, MCC can also be tuned with cationic antimicrobial compounds to fabricate an antimicrobial printable ink. However, due to the formation of complex coacervates between the two, the Pickering emulsion is very susceptible to phase separation with an insufficient therapeutic effect. To address this drawback, we reported a green method to produce antioxidant and antimicrobial three-dimensional (3D)-printed objects, illustrated here using a printable ink based on a soy-based particulate-type emulsion gel stabilized by a surface-active MCC conjugate (micro-biosurfactant). A sustainable method for the modification of MCC is investigated by grafting gallic acid onto the MCC backbone, followed by in situ reacting via lauric arginate through Schiff-base formation and/or Michael-type addition. Our results show that the grafted micro-biosurfactant was more efficient in providing the necessary physical stability of soy-based emulsion gel. The grafted micro-biosurfactant produced a multifunctional ink with viscoelastic behavior, thixotropic property, and outstanding bioactivities. Following the 3D printing process, highly porous 3D structures with a more precise geometry were fabricated after addition of the micro-biosurfactant. Dynamic sensory evaluation showed that the micro-biosurfactant has a remarkable ability to improve the temporal perceptions of fibrousness and juiciness in printed meat analogue. The results of this study showed the possibility of the development of a therapeutic 3D-printed meat analogue with desired sensory properties, conceiving it as a promising meat analogue product.

Application of Nanotechnology to Improve the Performance of Biodegradable Biopolymer-Based Packaging Materials

There is great interest in developing biodegradable biopolymer-based packaging materials whose functional performance is enhanced by incorporating active compounds into them, such as light blockers, plasticizers, crosslinkers, diffusion blockers, antimicrobials, antioxidants, and sensors. However, many of these compounds are volatile, chemically unstable, water-insoluble, matrix incompatible, or have adverse effects on film properties, which makes them difficult to directly incorporate into the packaging materials. These challenges can often be overcome by encapsulating the active compounds within food-grade nanoparticles, which are then introduced into the packaging materials. The presence of these nanoencapsulated active compounds in biopolymer-based coatings or films can greatly improve their functional performance. For example, anthocyanins can be used as light-blockers to retard oxidation reactions, or they can be used as pH/gas/temperature sensors to produce smart indicators to monitor the freshness of packaged foods. Encapsulated botanical extracts (like essential oils) can be used to increase the shelf life of foods due to their antimicrobial and antioxidant activities. The resistance of packaging materials to external factors can be improved by incorporating plasticizers (glycerol, sorbitol), crosslinkers (glutaraldehyde, tannic acid), and fillers (nanoparticles or nanofibers). Nanoenabled delivery systems can also be designed to control the release of active ingredients (such as antimicrobials or antioxidants) into the packaged food over time, which may extend their efficacy. This article reviews the different kinds of nanocarriers available for loading active compounds into these types of packaging materials and then discusses their impact on the optical, mechanical, thermal, barrier, antioxidant, and antimicrobial properties of the packaging materials. Furthermore, it highlights the different kinds of bioactive compounds that can be incorporated into biopolymer-based packaging.

Characterization of chitosan film with cinnamon essential oil emulsion co-stabilized by ethyl-Nα-lauroyl-l-arginate hydrochloride and hydroxypropyl-β-cyclodextrin

To improve the antimicrobial properties of chitosan films, cinnamon essential oil (CEO) nanoemulsion (1% and 3% v/v CEO) stabilized by ethyl-N^α-lauroyl-l-arginate hydrochloride (LAE) alone or co-stabilized by LAE and hydroxypropyl-β-cyclodextrin (HPCD) were incorporated into chitosan matrix. The micromorphology, physical and antimicrobial properties of the composite films were compared. The dense structure of the CEO nanoemulsion co-stabilized by LAE and HPCD reduced the water vapor permeability and water content. The incorporation of the CEO nanoemulsion co-stabilized by LAE and HPCD, reduced the adverse effects of CEO on the mechanical properties and microstructure of the film, and even slightly increased the tensile strength. In addition, the antimicrobial properties of chitosan films were enhanced due to the encapsulation and emulsification effect of HPCD and LAE on CEO. This work indicated that the prepared chitosan based edible films had the potential to be used in the field of food packaging to improve food safety.

Effect of Homogenization Method and Carvacrol Content on Microstructural and Physical Properties of Chitosan-Based Films

The use of EOs nanoemulsion to develop active edible films offers a new way to modify transport properties and to release active compounds while improving mechanical resistance, transparency, and antioxidant and antimicrobial activity. The aim of this study was to study the influence of homogenization conditions and carvacrol content on the microstructure and physical properties of edible nanoemulsified chitosan films. Film-forming emulsions (FFE) were prepared with chitosan (1.5%), Tween 80 (0.5%), and carvacrol (0.25%, 0.5%, and 1.0%); two homogenization methods were used (rotor-stator and rotor-stator followed by high-pressure homogenization). Film internal and surface microstructure was characterized by scanning electron microscopy (SEM) and film physical properties, such as mechanical, optical, and water barrier, were evaluated. Results showed that the high-pressure homogenization method promoted a significant change on film microstructure, leading to improved properties. Carvacrol droplets were smaller and homogeneously distributed in the film when 0.5% (v/v) carvacrol was incorporated (1:1 Tween 80: carvacrol ratio). As a consequence, emulsified films obtained at high pressure were less opaque, had greater elongation, and had a lower permeability to water vapor than those obtained by the rotor-stator method. Therefore, high-pressure homogenization is a good method to obtain edible emulsified films with desirable properties for food preservation.

Functional Properties of Biopolymer-Based Films Modified with Surfactants: A Brief Review

An increase of environmental awareness recently has increased the interest of researchers in using of biopolymer-based films. The films have been prepared extensively by utilizing starch, carboxymethyl cellulose, chitosan, protein, gelatin, carrageenan, alginate, pectin, guar gum and pullulan. They are typically modified with surface-active agents (surfactants) such as glycerol monostearate, sucrose ester, sodium stearoyl lactate, sodium dodecyl sulfate, ethyl lauroyl arginate HCl, Span 20 to 80, Tween-20 to 80 and soy lecithin for improving the functional properties of the films. In this brief review, two types of biopolymer-based films that prepared through casting method were categorized, specifically solution- and emulsion-based films. The four types of surfactants, namely non-ionic, anionic, cationic and amphoteric surfactants that are regularly used to modify biopolymer-based films are also described. The functional properties of the films modified with different types of surfactants are briefly reviewed. This study enhances the attraction of researchers in biopolymer-based films and the improvement of new concepts in this niche area.

A novel biodegradable film based on κ-carrageenan activated with olive leaves extract

This research focused on the development of carrageenan based biodegradable films incorporated with olive leaves extract (OLE). OLE microbial inhibition and its total phenolics (TP) were evaluated. Carrageenan films were produced by casting technique and were characterized by thickness, water vapor permeability (WVP), color, mechanical properties, and infrared spectroscopy. In order to apply as lamb meat packaging, the antimicrobial effect of the films was investigated. Results showed that OLE inhibited E. coli growth and presented excellent TP (41.40 mgGAE/g). Thicknesses of the film with OLE (CAR-OLE) were approximately 28% higher than film without OLE. Addition of OLE reduced the WVP by approximately 54%. CAR-OLE was less resistant to breakage and more flexible showing darker color. FTIR showed interaction of carrageenan with OLE. Results revealed that CAR-OLE promoted 167-fold reduction in initial count of aerobic mesophiles indicating shelf-life extension of lamb meat and promising use as antimicrobial food packaging.

Characterization and evaluation of a novel O-carboxymethyl chitosan films with Mimosa tenuiflora extract for skin regeneration and wound healing

In this study, films of O-carboxymethyl chitosan with Mimosa tenuiflora extract were manufactured, characterized, and evaluated. In this work, both the synthesis of O-carboxymethyl chitosan and the extraction of the active ingredient of Mimosa tenuiflora extract from the cortex are described. First, the extract of Mimosa tenuiflora in water was obtained by precipitation with ethanol, filtering, and concentrating. Subsequently, a study was conducted of scratch wound healing to determine the optimal concentration of extract to be used in the manufacture of films. The produced O-carboxymethyl chitosan films and the Mimosa tenuiflora extract were mixed, and their chemical composition, tensile properties, and wettability were characterized by Fourier-transform infrared spectroscopy, mechanical tests, and contact angle measurement. The antimicrobial properties of the films were tested by turbidimetry using two types of bacteria. In addition, a study of the enzymatic degradation of the films with the enzyme lysozyme was performed. Finally, in vitro studies to assess the biocompatibility and cytotoxicity of films with fibroblastic cells were carried out as well as the kinetic analysis of healing in mice. It was found that the addition of Mimosa tenuiflora extract in the polymer matrix of the films made with O-carboxymethyl chitosan improves the proliferation of fibroblast and accelerates wound healing, thus providing a novel biomaterial for skin regeneration.

Safely Dissolvable and Healable Active Packaging Films Based on Alginate and Pectin

Extensive usage of long-lasting petroleum based plastics for short-lived application such as packaging has raised concerns regarding their role in environmental pollution. In this research, we have developed active, healable, and safely dissolvable alginate-pectin based biocomposites that have potential applications in food packaging. The morphological study revealed the rough surface of these biocomposite films. Tensile properties indicated that the fabricated samples have mechanical properties in the range of commercially available packaging films while possessing excellent healing efficiency. Biocomposite films exhibited higher hydrophobicity properties compared to neat alginate films. Thermal analysis indicated that crosslinked biocomposite samples possess higher thermal stability in temperatures below 120 °C, while antibacterial analysis against E. coli and S. aureus revealed the antibacterial properties of the prepared samples against different bacteria. The fabricated biodegradable multi-functional biocomposite films possess various imperative properties, making them ideal for utilization as packaging material.

Pharmaceutical applications of chitosan

Chitosan (CS) is a linear polysaccharide which is achieved by deacetylation of chitin, which is the second most plentiful compound in nature, after cellulose. It is a linear copolymer of β-(1 → 4)-linked 2-acetamido-2-deoxy-β-d-glucopyranose and 2-amino-2-deoxy-β-d-glucopyranose. It has appreciated properties such as biocompatibility, biodegradability, hydrophilicity, nontoxicity, high bioavailability, simplicity of modification, favorable permselectivity of water, outstanding chemical resistance, capability to form films, gels, nanoparticles, microparticles and beads as well as affinity to metals, proteins and dyes. Also, the biodegradable CS is broken down in the human body to safe compounds (amino sugars) which are easily absorbed. At present, CS and its derivatives are broadly investigated in numerous pharmaceutical and medical applications including drug/gene delivery, wound dressings, implants, contact lenses, tissue engineering and cell encapsulation. Besides, CS has several OH and NH₂ functional groups which allow protein binding. CS with a deacetylation degree of ~50% is soluble in aqueous acidic environment. While CS is dissolved in acidic medium, its amino groups in the polymeric chains are protonated and it becomes cationic which allows its strong interaction with different kinds of molecules. It is believed that this positive charge is responsible for the antimicrobial activity of CS through the interaction with the negatively charged cell membranes of microorganisms. This review presents properties and numerous applications of chitosan-based compounds in drug delivery, gene delivery, cell encapsulation, protein binding, tissue engineering, preparation of implants and contact lenses, wound healing, bioimaging, antimicrobial food additives, antibacterial food packaging materials and antibacterial textiles. Moreover, some recent molecular dynamics simulations accomplished on the pharmaceutical applications of chitosan were presented.

Bioaccessibility and antimicrobial properties of a shrimp demineralization extract blended with chitosan as wrapping material in ready-to-eat raw salmon

A shrimp extract (SME) obtained from the mild-acid demineralization treatment of shrimp shells to produce chitosan was collected. It was mainly composed of fat (≈73%), protein (≈19%), and ash (≈9%) and contained considerable amounts of calcium (≈1.9 g/100 g), astaxanthin (≈30 mg/100 g) and unsaturated fatty acids (≈27% MUFA, ≈39% PUFA). The SME was used in combination with chitosan for wrapping raw salmon to produce a ready-to-eat product enriched in calcium. No significant changes in hardness were found, as compared to the unwrapped salmon. Estimated intakes of bioaccessible calcium increased significantly by 3.6-fold, whereas intake of bioaccessible fat was reduced by 15%. SFA were the main fatty acid group reduced (≈80%), whereas MUFA and PUFA were only reduced by ≈20% each. Total viable counts, pseudomonads, enterobacteria, and specific fish spoilers were reduced by 2-4 log CFU/g in wrapped sample during the chilled storage period (19 days).

A simple, efficient and economic method for obtaining iodate-rich chili pepper based chitosan edible thin film

The present study was aimed at designing an iodine supplement in form of edible film made of iodate-coated chitosan (CS-IO₃). Inclusion of so obtained films in diet can help in preventing thyroid cancer, leading to improved public health. Chili pepper was coated with iodate thin film (1.5 µm). The iodate-rich film is ready-to-eat serving valuable nutrients. Stability studies of CS-IO₃ film using water dipping revealed that there was no leaching of iodate ion, due to the strong interactions between cationic amino group of chitosan and iodate ion. The film showed no change in its antioxidant activity. Iodate concentration in the film was determined at 620 nm selectively, based on the decolorization of malachite green economic method. Iodate content in fruits coated with 1.5% (w/v) CS-IO₃ was 11.5 mg g^-1 of dry film sample. The iodate-rich samples could be stored without much effect on its freshness, indicating a good shelf life.

Influence of Codium tomentosum Extract in the Properties of Alginate and Chitosan Edible Films

The growing search for natural alternatives to synthetic food packaging materials and additives has increased, and seaweed extracts’ bioactivity has made them suitable candidates for incorporation in novel edible films. This study aims to investigate the effect of Codium tomentosum seaweed extract (SE) incorporation in alginate and chitosan edible films. Alginate- and chitosan-based films with and without the incorporation of 0.5% SE were characterized according to their physical, optical, mechanical, and thermal properties. Seaweed extract incorporation in chitosan films resulted in an increase of film solubility (50%), elasticity (18%), and decrease of puncture strength (27%) and energy at break (39%). In alginate films, the extract incorporation significantly decreased film solubility (6%), water vapour permeability (46%), and elasticity (24%), and had no effect on thermal properties. Depending on the type of application, the addition of SE in edible films can bring advantages for food conservation.

Antibacterial Films Made of Ionic Complexes of Poly(γ-glutamic acid) and Ethyl Lauroyl Arginate

The biocide agent LAE (ethyl ^αN-lauroyl l-arginate chloride) was coupled with poly(γ-glutamic acid) (PGGA) to form stable ionic complexes with LAE:PGGA ratios of 1 and 0.5. The nanostructure adopted by these complexes and its response to thermal changes were examined in detail by Differential scanning calorimetry (DSC) and X-ray diffraction (XRD) using synchrotron radiation in real time. A layered biphasic structure with LAE filling the space between the polypeptidic sheets was adopted in these complexes. The complexes were stable up to above 250 °C, non-water soluble, and were able to form consistent transparent films. The release of LAE from the complexes upon incubation in aqueous buffer was examined and found to depend on both pH and complex composition. The antibacterial activity of films made of these complexes against Gram-positive (L. monocytogenes and S. aureus) and Gram-negative (E. coli and S. enterica) bacteria was preliminary evaluated and was found to be very high against the formers and only moderate against the later. The bactericide activity displayed by the LAE·PGGA complexes was directly related with the amount of LAE that was released from the film to the environment.

Preservation Mechanism of Chitosan-Based Coating with Cinnamon Oil for Fruits Storage Based on Sensor Data

The chitosan-based coating with antimicrobial agent has been developed recently to control the decay of fruits. However, its fresh keeping and antimicrobial mechanism is still not very clear. The preservation mechanism of chitosan coating with cinnamon oil for fruits storage is investigated in this paper. Results in the atomic force microscopy sensor images show that many micropores exist in the chitosan coating film. The roughness of coating film is affected by the concentration of chitosan. The antifungal activity of cinnamon oil should be mainly due to its main consistent trans-cinnamaldehyde, which is proportional to the trans-cinnamaldehyde concentration and improves with increasing the attachment time of oil. The exosmosis ratios of Penicillium citrinum and Aspergillus flavus could be enhanced by increasing the concentration of cinnamon oil. Morphological observation indicates that, compared to the normal cell, the wizened mycelium of A. flavus is observed around the inhibition zone, and the growth of spores is also inhibited. Moreover, the analysis of gas sensors indicate that the chitosan-oil coating could decrease the level of O₂ and increase the level of CO₂ in the package of cherry fruits, which also control the fruit decay. These results indicate that its preservation mechanism might be partly due to the micropores structure of coating film as a barrier for gas and a carrier for oil, and partly due to the activity of cinnamon oil on the cell disruption.

Chitosan-Based Coating with Antimicrobial Agents: Preparation, Property, Mechanism, and Application Effectiveness on Fruits and Vegetables

Chitosan coating is beneficial to maintaining the storage quality and prolonging the shelf life of postharvest fruits and vegetables, which is always used as the carrier film for the antimicrobial agents. This review focuses on the preparation, property, mechanism, and application effectiveness on the fruits and vegetables of chitosan-based coating with antimicrobial agents. Chitosan, derived by deacetylation of chitin, is a modified and natural biopolymer as the coating material. In this article, the safety and biocompatible and antimicrobial properties of chitosan were introduced because these attributes are very important for its application. The methods to prepare the chitosan-based coating with antimicrobial agents, such as essential oils, acid, and nanoparticles, were developed by other researchers. Meanwhile, the application of chitosan-based coating is mainly due to its antimicrobial activity and other functional properties, which were investigated, introduced, and analyzed in this review. Furthermore, the surface and mechanical properties were also investigated by researchers and concluded in this article. Finally, the effects of chitosan-based coating on the storage quality, microbial safety, and shelf life of fruits and vegetables were introduced. Their results indicated that chitosan-based coating with different antimicrobial agents would probably have wide prospect in the preservation of fruits and vegetables in the future.