Impact of dyes and finishes on the aquatic biodegradability of cotton textile fibers and microfibers released on laundering clothes: Correlations between enzyme adsorption and activity and biodegradation rates

Microplastic removal and risk assessment framework in a constructed wetland for the treatment of combined sewer overflows

Combined sewer overflows (CSOs) release a significant amount of pollutants, including microplastics (MPs), due to the discharge of untreated water into receiving water bodies. Constructed Wetlands (CWs) offer a promising strategy for CSO treatment and have recently attracted attention as a potential solution for MP mitigation. Nevertheless, limited research on MP dynamics within CSO events and MP removal performance in full-scale CW systems poses a barrier to this frontier of application. This research aims to address both these knowledge gaps, representing the first investigation of a multi-stage CSO-CW for MP removal. The study presents one year of seasonal data from the CSO-CW upstream of the WWTP in Carimate (Italy), evaluating the correlation of MP abundance with different water quality/quantity parameters and associated ecological risks. The results show a clear trend in MP abundance, which increases with rainfall intensity. The strong correlation between MP concentration, flow rate, and total suspended solids (TSS) validates the first flush phenomenon hypothesis and its impact on MP release during CSOs. Chemical characterization identifies acrylonitrile-butadiene-styrene (ABS), polyethylene (PE), and polypropylene (PP) as predominant polymers. The first vertical subsurface flow (VF) stage showed removal rates ranging from 40 % to 77 %. However, the unexpected increase in MP concentrations after the second free water surface (FWS) stage suggests the stochasticity of CSO events and the different hydraulic characteristics of the CW units have diverse effects on MP retention. These data confirm filtration as the main retention mechanism for MP within CW systems. The MP ecological risk assessment indicates a high-risk category for most of the water samples, mainly related to the frequent presence of ABS fragments. The results contribute to the current understanding of MPs released by CSOs and provide insights into the performance of different treatment units within a large-scale CSO-CW system, suggesting the requirement for further attention.

Micro- and Nanoplastics Produced from Textile Finishes: A Review

The problem of increasing plastic pollution has emerged as a significant societal issue. Plastics can originate from various sources, and there is growing concern among researchers to study and investigate this new category of pollution. The plastic waste is found at the macro, micro, and nanoscale, and its study has had great significance according to the perspective of posing hazardous impacts on living organisms. Given the high demand for functional textiles, the textile industries are supporting the coating of different polymeric based finishes on the surface of textile products. The plastic debris emitted from these coated finishes are in the ranges of nanometric scale, so-called polymeric nanoplastics (PNPs). With the new terminology, polymeric nanoplastics (PNPs) released from textile finishes or coatings are being increasingly mentioned, and the term fibrous microplastics (FMPs) can be seen as outdated. This study is based on an intensive review of a very novel category of debris plastics (PNPs) mostly produced from textile finishes or coatings. In fact, FMPs and PNPs released from synthetic textiles and textiles coated with plastic-based finishes during washing activities are considered to be a major cause that contributes to the current overall load of microplastics (MPs) in the environment. A link between the concentration of NPs from textile fibers and NPs from textile polymeric-based coatings in freshwater and sediments within a particular local setting and the extent of activities of the textile industry has been demonstrated. Invested efforts have been paid to consider and concentrate on plastic pollution (nanoplastics from textile polymeric coatings). We also summarize existing methodologies to elucidate the identification and proactive quantification of nanoplastics shed from the textile polymeric coatings. To this end, more than 40 studies have been done to identify the physical, chemical, and mechanical parameters and to characterize nanoplastics.

Environmentally Friendly Approach to the Reduction of Microplastics during Domestic Washing: Prospects for Machine Vision in Microplastics Reduction

The increase in the global population is directly responsible for the acceleration in the production as well as the consumption of textile products. The use of textiles and garment materials is one of the primary reasons for the microfibers generation and it is anticipated to grow increasingly. Textile microfibers have been found in marine sediments and organisms, posing a real threat to the environment as it is invisible pollution caused by the textile industry. To protect against the damaging effects that microplastics can have, the formulation of mitigation strategies is urgently required. Therefore, the primary focus of this review manuscript is on finding an environmentally friendly long-term solution to the problem of microfiber emissions caused by the domestic washing process, as well as gaining an understanding of the various properties of textiles and how they influence this problem. In addition, it discussed the effect that mechanical and chemical finishes have on microfiber emissions and identified research gaps in order to direct future research objectives in the area of chemical finishing processes. In addition to that, it included a variety of preventative and minimizing strategies for reduction. Last but not least, an emphasis was placed on the potential and foreseeable applications of machine vision (i.e., quantification, data storage, and data sharing) to reduce the amount of microfibers emitted by residential washing machines.

Impact of vented and condenser tumble dryers on waterborne and airborne microfiber pollution

Laundering of textiles is a significant source of waterborne microfiber pollution, and solutions are now being sought to mitigate this issue including improvements in clothing technology and integration of filtration systems into washing machines. Vented tumble dryers are a potential source of airborne microfiber pollution, as their built-in lint filtration systems have been found to be inefficient with significant quantities of textile microfibers being released to the external environment through their exhaust air ducts. The present study is the first to evaluate the impact of condenser dryers, finding that they are significant contributors to waterborne microfiber pollution from the lint filter (if users clean this with water), the condenser and the condensed water. Microfiber release from drying of real consumer loads in condenser and vented tumble dryers was compared, finding that real loads release surprisingly high levels of microfibers (total 341.5 ± 126.0 ppm for those dried in a condenser dryer and 256.0 ± 74.2 ppm for those dried in a vented dryer), similar in quantity to microfibers produced during the first highly-shedding drying cycle of a new T-shirt load (total 321.4 ± 11.2 ppm) in a condenser dryer. Vented dryers were found to be significant contributors to waterborne microfiber pollution if consumers clean the lint filter with water in accordance with some published appliance usage instructions, as most (86.1 ± 5.5% for the real consumer loads tested) of the microfibers generated during vented tumble drying were collected on the lint filter. Therefore, tumble dryers are a significant source of waterborne and (for vented dryers) airborne microfiber pollution. While reducing the pore size of tumble dryer lint filters and instructing consumers to dispose of fibers collected on lint filters as municipal solid waste could help reduce the issue, more sophisticated engineering solutions will likely be required to achieve a more comprehensive solution.

Fibrous microplastics released from textiles: Occurrence, fate, and remediation strategies

Microplastics (MP), i.e., particles measuring less than 5 mm in size, are considered emerging pollutants. The ubiquity of MP is causing great concern among environmental and public health agencies. Anthropogenic activities are responsible for the extensive dispersal of MP in nature. Adverse effects on living organisms, interactions with other contaminants occurring in the environment, and the lack of effective degradation/removal techniques are significant issues related to MP. Most MP found in nature are fibrous (FMP). FMP originate from textile products, mainly synthetic fibers (e.g., polyester). Synthetic fibers are intensively used to produce countless goods due to beneficial characteristics such as high mechanical resistance and economic feasibility. FMP are ubiquitous on the planet and impart lasting adverse effects on biodiversity. Data on the consequences of long-term exposure to these pollutants are scarce in the literature. In addition, few studies address the main types of synthetic microfibers released from textiles, their occurrence, adverse effects on organisms, and remediation strategies. This review discusses the relevant topics about FMP and alerts the dangers to the planet. Furthermore, future perspectives and technological highlights for the FMP mitigation/degradation are presented.

Efficiency of Coagulation/Flocculation for the Removal of Complex Mixture of Textile Fibers from Water

Synthetic fibers enter wastewater treatment plants together with natural fibers, which may affect treatment efficiency, a fact not considered in previous studies. Therefore, the aim of the present study was to evaluate the efficiency of the coagulation/flocculation process for the removal of a mixture of textile fibers from different water matrices. Natural and synthetic fibers (100 mg/L; cotton, polyacrylonitrile, and polyamide) were added to a synthetic matrix, surface water and laundry wastewater and subjected to coagulation/flocculation experiments with ferric chloride (FeCl3) and polyaluminum chloride (PACl) under laboratory conditions. In the synthetic matrix, both coagulants were found to be effective, with FeCl3 having a lesser advantage, removing textile fibers almost completely from the water (up to 99% at a concentration of 3.94 mM). In surface water, all dosages had approximately similar high values, with the coagulant resulting in complete removal. In laundry effluent, the presence of surfactants is thought to affect coagulation efficiency. PACl was found to be effective in removing textile fibers from laundry wastewater, with the lowest removal efficiency being 89% and all dosages having similar removal efficiencies. Natural organic matter and bicarbonates showed a positive effect on the efficiency of FeCl3 in removing textile fibers from surface water. PACl showed better performance in coagulating laundry wastewater while surfactants had a negative effect on FeCl3 coagulation efficiency.

Natural bioactive formulations for biodegradable cotton eco-fabrics with antimicrobial and fire-shielding properties

In this study, eco-friendly cotton fabrics with antimicrobial and flame-retardant properties were produced using newly developed bioactive formulations. The new natural formulations combine the biocidal properties of the biopolymer (chitosan (CS)) and essential oil (thyme oil) (EO) with the flame-retardant properties of mineral fillers (silica (SiO₂), zinc oxide (ZnO), titanium dioxide (TiO₂), and hydrotalcite (LDH)). The modified cotton eco-fabrics were analyzed in terms of morphology (optical and scanning electron microscopy (SEM)), color (spectrophotometric measurements), thermal stability (thermogravimetric analysis (TGA)), biodegradability, flammability (micro-combustion calorimetry (MCC)), and antimicrobial characteristics. The antimicrobial activity of the designed eco-fabrics was determined against different kinds of microorganism (S. aureus, E. coli, P. fluorescens, B. subtilis, A. niger, C. albicans). The antibacterial effects and flammability of the materials were found to depend strongly on the compositions of the bioactive formulation. The best results were obtained for the samples of fabric coated with the formulations containing LDH and TiO₂ filler. These samples showed the highest decreases in flammability, with heat release rate (HRR) values of 168 (W/g) and 139 (W/g), respectively, compared to the reference (233 W/g). The samples also showed very good inhibition of growth against of all the studied bacteria.

Prevalence and characterisation of microfibres along the Kenyan and Tanzanian coast

Microplastic pollution is ubiquitous, with textiles being a major source of one of the dominant microplastic types—microfibres. Microfibres have been discovered in the aquatic environment and marine biota, demonstrating direct infiltration in the environment. However, the impact of non-plastic microfibres has been overlooked until recently despite their prevalence and the ecotoxicological risk posed by chemical dyes and finishes used during processing. During an expedition from Lamu to Zanzibar (East Africa), a citizen science strategy was employed to innovate, educate and influence microfibre pollution reform through the Flipflopi project, a circular economy effort to stop the use of single-use plastic. Simple sampling methods were developed to replace costly equipment, which local citizens could use to partake in the collection and sampling of surface water samples from the previously understudied Kenyan and Tanzanian coast. To maintain the reliability of samples and to minimise contamination, a forensic science strategy was embedded throughout the methodology of the study, collection and analysis of the samples. A total of 2,403 microfibres from 37 sites were recovered and fully characterised with 55% found to be of natural origin, 8% regenerated cellulosic and 37% synthetic microfibres. Natural microfibres were in higher abundance in 33 of the 37 sampled sites. Congruent with recent studies, these findings further support the need for greater understanding of the anthropogenic impact of natural microfibres.

Review of research on migration, distribution, biological effects, and analytical methods of microfibers in the environment

Microplastics have been proven to be one of the critical environmental pollution issues. Moreover, microfibers, the most prominent form of microplastics in the environment, have likewise attracted the attention of various countries. With the increase in global population and industrialization, the production and use of fibers continue to increase yearly. As a result, a large number of microfibers are formed. If fiber products are not used or handled correctly, it will cause direct/indirect severe microfiber environmental pollution. Microfibers will be further broken into smaller fiber fragments when they enter the natural environment. Presently, researchers have conducted extensive research in the identification of microfibers, laying the foundation for further resourcefulness research. This work used bibliometric analysis to review the microfiber contamination researches systematically. First, the primary sources of microfibers and the influencing factors are analyzed. We aim to summarize the influence of the clothing fiber preparation and care processes on microfiber formation. Then, this work elaborated on the migration in/between water, atmosphere, and terrestrial environments. We also discussed the effects of microfiber on ecosystems. Finally, microfibers' current and foreseeable effective treatment, disposal, and resource utilization methods were explained. This paper will provide a structured reference for future microfiber research.

First assessment of microplastic and artificial microfiber contamination in surface waters of the Amazon Continental Shelf

The composition and distribution of microplastics (MPs) in the Brazilian Amazon Continental Shelf surface waters are described for the first time. The study was conducted during the 2018 rainy and dry seasons, using 57 water samples collected with aluminum buckets and filtered through a 64-μm mesh. The samples were vacuum-filtered in a still-air box, and the content of each filter was measured, counted, and classified. A total of 12,288 floating MPs were retrieved; particles were present at all 57 sampling points. The mean MP abundance was 3593 ± 2264 items·m^-3, with significantly higher values during the rainy season (1500 to 12,967; 4772 ± 2761 items·m^-3) than in the dry season (323 to 5733; 2672 ± 1167 items·m^-3). Polyamides (PA), polyurethane (PU), and acrylonitrile butadiene styrene (ABS) were the most common polymers identified through Fourier Transform Infrared Spectroscopy (FTIR) analysis. Cellulose-based textile fibers were also abundant (~40%). Our results indicate that the Amazon Continental Shelf is contaminated with moderate to high levels of MPs; the highest abundances were recorded at stations near land-based sources such as river mouths and large coastal cities.

Microfiber shedding from nonwoven materials including wipes and meltblown nonwovens in air and water environments

Nonwoven products are widely used in disposable products, such as wipes, diapers, and masks. Microfibers shed from these products in the aquatic and air environment have not been fully described. In the present study, 15 commercial single-use nonwoven products (wipes) and 16 meltblown nonwoven materials produced in a pilot plant were investigated regarding their microfiber generation in aquatic and air environments and compared to selected textile materials and paper tissue materials. Microfibers shed in water were studied using a Launder Ometer equipment (1-65 mg of microfibers per gram material), and microfibers shed in air were evaluated using a dusting testing machine that shakes a piece of the nonwoven back and forth (~ 4 mg of microfibers per gram material). The raw materials and bonding technologies affected the microfiber generation both in water and air conditions. When the commercial nonwovens contained less natural cellulosic fibers, less microfibers were generated. Bonding with hydroentangling and/or double bonding by two different bonding methods could improve the resistance to microfiber generation. Meltblown nonwoven fabrics generated fewer microfibers compared to the other commercial nonwovens studied here, and the manufacturing factors, such as DCD (die-to-collector distance) and air flow rate, affected the tendency of microfiber generation. The results suggest that it is possible to control the tendency of microfiber shedding through the choice of operating parameters during nonwoven manufacturing processes.

Environmental contamination by microplastics originating from textiles: Emission, transport, fate and toxicity

Microplastic (MP) pollution has become a global concern in terms of its environmental abundance and potential detrimental effects. Fibrous microplastics (FMPs) released from synthetic textiles are believed to contribute significantly to environmental MP pollution. This review provides an overview of current knowledge relating to the environmental impact of FMPs through a summary and discussion of (1) the concentrations in different environmental compartments including water, soil and air, (2) emission from wastewater treatment plants: via effluent discharges to waters and via sludge to land, (3) environmental transport and fate, and (4) toxicity and associated effects. How the properties of FMPs influence these aspects is discussed and their behaviour is compared to MPs of other shapes. We have summarised the Environmental Concentrations and derived Predicted No-Effect Concentrations for a preliminary risk assessment of FMPs by extrapolating the risk quotient for each respective environmental compartment. The uncertainties surrounding current assessment methods are discussed. In particular we address the need to improve determination of exposure levels and to better characterise the effects of FMPs. We conclude by presenting topics for future studies to address, which will improve our still limited understanding of the interactions between FMPs and the environment.

Environmental effects of stratospheric ozone depletion, UV radiation, and interactions with climate change: UNEP Environmental Effects Assessment Panel, Update 2021

The Environmental Effects Assessment Panel of the Montreal Protocol under the United Nations Environment Programme evaluates effects on the environment and human health that arise from changes in the stratospheric ozone layer and concomitant variations in ultraviolet (UV) radiation at the Earth's surface. The current update is based on scientific advances that have accumulated since our last assessment (Photochem and Photobiol Sci 20(1):1-67, 2021). We also discuss how climate change affects stratospheric ozone depletion and ultraviolet radiation, and how stratospheric ozone depletion affects climate change. The resulting interlinking effects of stratospheric ozone depletion, UV radiation, and climate change are assessed in terms of air quality, carbon sinks, ecosystems, human health, and natural and synthetic materials. We further highlight potential impacts on the biosphere from extreme climate events that are occurring with increasing frequency as a consequence of climate change. These and other interactive effects are examined with respect to the benefits that the Montreal Protocol and its Amendments are providing to life on Earth by controlling the production of various substances that contribute to both stratospheric ozone depletion and climate change.

Towards the Sustainability of the Plastic Industry through Biopolymers: Properties and Potential Applications to the Textiles World

This study aims to provide an overview of the latest research studies on the use of biopolymers in various textile processes, from spinning processes to dyeing and finishing treatment, proposed as a possible solution to reduce the environmental impact of the textile industry. Recently, awareness of various polluting aspects of textile production, based on petroleum derivatives, has grown significantly. Environmental issues resulting from greenhouse gas emissions, and waste accumulation in nature and landfills, have pushed research activities toward more sustainable, low-impact alternatives. Polymers derived from renewable resources and/or with biodegradable characteristics were investigated as follows: (i) as constituent materials in yarn production, in view of their superior ability to be decomposed compared with common synthetic petroleum-derived plastics, positive antibacterial activities, good breathability, and mechanical properties; (ii) in textile finishing to act as biological catalysts; (iii) to impart specific functional properties to treated textiles; (iv) in 3D printing technologies on fabric surfaces to replace traditionally more pollutive dye-based and inkjet printing; and (v) in the implants for the treatment of dye-contaminated water. Finally, current projects led by well-known companies on the development of new materials for the textile market are presented.

Laundering of face masks represents an additional source of synthetic and natural microfibers to aquatic ecosystems

From the onset of Covid-19 pandemic, the use of face masks has been adapted as one of the main measures to slow down the transmission of the SARS-CoV-2 virus worldwide. The inadequate handling and management of face masks lead to a massive dispersal in the environment, resulting in a new source of microfibers because of their breakdown and/or degradation. In addition, the laundering of reusable face masks of different polymeric composition can represent an additional sources of microfibers to natural ecosystems, but it was largely neglected. The present study explored the release of synthetic or natural microfibers from reusable and disposable face masks of five different fabrics when subjected to a cycle of laundering in a domestic washing machine. After a single wash, face masks released an average (± SE) of 284.94 ± 73.66 microfibers, independently of the fabrics. Focusing on the fabrics composing the face masks, polyurethane (541.33 ± 51.84 microfibers) and cotton-based (823.00 ± 112.53 microfibers) face masks released the highest amount of synthetic and natural microfibers, respectively. Considering the crucial role of face masks to counteract the pandemic and the increasing trend of their use, further studies represent a priority to estimate the contribution of face mask-derived microfibers to freshwater contamination.

Quantification of microplastics in sediments from Narragansett Bay, Rhode Island USA using a novel isolation and extraction method

Microplastics are small plastic particles found ubiquitously in marine environments. In this study, a hybridized method was developed for the extraction of microplastics (45-1000 μm) from sediments using sodium bromide solution for density separation. Method development was tested using spiked microplastics as internal standards. The method was then used to extract microplastics from sediments in Narragansett Bay, Rhode Island, USA. Suspect microplastics were analyzed with Raman spectroscopy. Microplastic abundance ranged from 40 particles/100 g sediment to 4.6 million particles/100 g sediment (wet weight). Cellulose acetate fibers were the most abundant microplastic. These results are some of the first data for microplastics in Rhode Island sediments.

Strategies and progress in synthetic textile fiber biodegradability

Abstract

The serious issue of textile waste accumulation has raised attention on biodegradability as a possible route to support sustainable consumption of textile fibers. However, synthetic textile fibers that dominate the market, especially poly(ethylene terephthalate) (PET), resist biological degradation, creating environmental and waste management challenges. Because pure natural fibers, like cotton, both perform well for consumer textiles and generally meet certain standardized biodegradability criteria, inspiration from the mechanisms involved in natural biodegradability are leading to new discoveries and developments in biologically accelerated textile waste remediation for both natural and synthetic fibers. The objective of this review is to present a multidisciplinary perspective on the essential bio-chemo-physical requirements for textile materials to undergo biodegradation, taking into consideration the impact of environmental or waste management process conditions on biodegradability outcomes. Strategies and recent progress in enhancing synthetic textile fiber biodegradability are reviewed, with emphasis on performance and biodegradability behavior of poly(lactic acid) (PLA) as an alternative biobased, biodegradable apparel textile fiber, and on biological strategies for addressing PET waste, including industrial enzymatic hydrolysis to generate recyclable monomers. Notably, while pure PET fibers do not biodegrade within the timeline of any standardized conditions, recent developments with process intensification and engineered enzymes show that higher enzymatic recycling efficiency for PET polymer has been achieved compared to cellulosic materials. Furthermore, combined with alternative waste management practices, such as composting, anaerobic digestion and biocatalyzed industrial reprocessing, the development of synthetic/natural fiber blends and other strategies are creating opportunities for new biodegradable and recyclable textile fibers.

Article Highlights

Occurrence and characterization of microplastic and mesoplastic pollution in the Migliarino San Rossore, Massaciuccoli Nature Park (Italy)

Microplastics pollution is progressively threatening natural parks across the world. In the framework of monitoring this concerning trend, the present study focuses on the occurrence and identification of mesoplastics (MEPs) and microplastics (MPs) in sand samples collected before and after the summer season from the beach of the Nature Park of Migliarino San Rossore Massaciuccoli (Pisa, Italy). Meso- and microplastics were identified using Fourier transform infrared spectroscopy 2D Imaging, and detected in all samples with average concentrations of 207 ± 30 MPs/kg d.w., and 100 ± 44 MEPs/kg d.w., respectively. Seasonal changes of flow of the Arno River, industrial activities, and urban footprint were considered as the major sources of plastic pollution. Our results showed the occurrence of both natural and synthetic polymers including cellulose, polyethylene, polypropylene, polyamides, polyethylene terephthalate, and acrylonitrile.

Drug-Eluting Medical Textiles: From Fiber Production and Textile Fabrication to Drug Loading and Delivery

Drug-eluting medical textiles have recently gained great attention to be used in different applications due to their cost effectiveness and unique physical and chemical properties. Using various fiber production and textile fabrication technologies, fibrous constructs with the required properties for the target drug delivery systems can be designed and fabricated. This review summarizes the current advances in the fabrication of drug-eluting medical textiles. Different fiber production methods such as melt-, wet-, and electro-spinning, and textile fabrication techniques such as knitting and weaving are explained. Moreover, various loading processes of bioactive agents to obtain drug-loaded fibrous structures with required physicochemical and morphological properties, drug delivery mechanisms, and drug release kinetics are discussed. Finally, the current applications of drug-eluting fibrous systems in wound care, tissue engineering, and transdermal drug delivery are highlighted.

Plastic microfibre pollution: how important is clothes' laundering?

Plastic microfibre pollution produced by domestic and commercial laundering of synthetic textiles has recently been incriminated in the press and the scientific literature as the main source (up to 90%) of primary microplastics in the oceans. Polyethylene terephthalate (PET) is the most common microfibre encountered. This review aims to provide updated information on worldwide plastic microfibre pollution caused by textile laundering and some possibilities for its control. Release of microfibres during domestic washing and tumble drying, their fate in wastewater treatment plants (WWTPs) and the oceans, and their environmental effects on the aquatic biota are discussed, as well as potential control methods at the levels of textile modification and laundry procedures. Environmental effects on aquatic biota are important; as a result of their small size and length-to-diameter ratio, microfibers are more effectively incorporated by organisms than other plastic particle groups. Simulation laundering studies may be useful in the development of a Standard Test Method and modification of WWTPs may reduce microfibre release into aquatic systems. However, improvements will be necessary in textile design and appliance design, and recommendations should be made to consumers about reducing their personal impact on the environment through their laundering choices, which can include appliances, fabric care products and washing conditions. Official regulation, such as that introduced recently by the French government, may be necessary to reduce plastic microfibre release from clothes' laundering.