Tangential streaming potential/current measurements for the characterization of composite membranes

Dual-Functional Nanofiltration and Adsorptive Membranes for PFAS and Organics Separation from Water

Challenges associated with water separation technologies for per- and polyfluoroalkyl substances (PFASs) require efficient and sustainable processes supported by a proper understanding of the separation mechanisms. The solute rejections by nanofiltration (NF) at pH values near the membrane isoelectric point were compared to the size- and mass-transfer-dependent modeled rejection rates of these compounds in an ionized state. We find that the low pK a value of perfluorooctanoic acid (PFOA) relates to enhanced solute exclusions by minimizing the presence and partitioning of the protonated organic compound into the membrane domain. The effects of Donnan exclusion are moderate, and co-ion transport also contributes to the PFAS rejection rates. An additional support barrier with thermo-responsive (quantified by water permeance variation) adsorption/desorption properties allows for enhanced separations of PFAS. This was possible by successfully synthesizing an NF layer on top of a poly-N-isopropylacrylamide (PNIPAm) pore-functionalized microfiltration support structure. The support layer adsorbs organics (178 mg PFOA adsorbed/m2 membrane at an equilibrium concentration of 70 mg/L), and the simultaneous exclusion from the NF layer allows separations of PFOA and the smaller sized heptafluorobutyric acid from solutions containing 70 μg/L of these compounds at a high water flux of 100 L/m2-h at 7 bar.

3D-PLA-experimental set up to display the electrical background of the so-called geometric factor of electrokinetic cells

The so-called geometric factor defined in electrokinetic cells, L/S (L being the length and S the cross-section of the channel), is relevant for providing the surface interaction electrical potential (zeta potential, ζ) of large surfaces, such as those used in the design of biomedical devices or water purification systems. Conversely, recent studies demonstrate that this factor is also employed to determine geometrical parameters, such as porosity in membrane-like systems. This factor, which has been attributed exclusively a geometrical character, can also be obtained from the electrical conductivity and resistance of the electrokinetic channel. In this work, we assess whether these two ways of obtaining the L/S factor are equivalent and how possible deviations can affect the value of the zeta potential. For this purpose, we work with channels of different geometries obtained by 3D printing using PLA (polylactic acid) as a polymer employed in biomedical applications. The discrepancies between the L/S factor obtained by electrical and purely geometrical measurements increase as the geometrical L/S factor becomes larger, reaching differences close to 80%. The results show that the so-called geometrical L/S factor also has an important electrical contribution and would be better denoted as electrogeometric factor. The differences found between the L/S factors are also propagated to the calculation of ζ but an optimum conductivity zone (from about 10 to 40 mS m-1) can be defined to obtain the zeta potential by selecting any of the L/S factors obtained from electrokinetic measurements. The results of this work should be taken into account in those investigations that use the L/S factor to obtain the geometry-porosity of permeable materials.

Positively charged nanofiltration membrane synthesis, transport models, and lanthanides separation

The design and understanding of rejection mechanisms for both positively and negatively charged nanofiltration (NF) membranes are needed for the development of highly selective separation of multivalent ions. In this study, positively charged nanofiltration membranes were created via an addition of commercially available polyallylamine hydrochloride (PAH) by conventional interfacial polymerization technique. Demonstration of real increase in surface zeta potential, along with other characterization methods, confirmed the addition of weak basic functional groups from PAH. Both positively and negatively charged NF membranes were tested for evaluating their potential as a technology for the recovery or separation of lanthanide cations (neodymium and lanthanum chloride as model salts) from aqueous sources. Particularly, the NF membranes with added PAH performed high and stable lanthanides retentions, with values around 99.3% in mixtures with high ionic strength (100 mM, equivalent to ~6,000 ppm), 99.3% rejection at 85% water recovery (and high Na+/La3+ selectivity, with 0% Na+ rejection starting at 65% recovery), and both constant lanthanum rejection and permeate flux at even pH 2.7. Donnan steric pore model with dielectric exclusion elucidated the transport mechanism of lanthanides and sodium, proving the potential of high selective separation at low permeate fluxes using positively charged NF membranes.

Runge-Kutta Numerical Method Followed by Richardson's Extrapolation for Efficient Ion Rejection Reassessment of a Novel Defect-Free Synthesized Nanofiltration Membrane

A defect-free, loose, and strong layer consisting of zirconium (Zr) nanoparticles (NPs) has been successfully established on a polyacrylonitrile (PAN) ultrafiltration substrate by an in-situ formation process. The resulting organic–inorganic nanofiltration (NF) membrane, NF-PANZr, has been accurately characterized not only with regard to its properties but also its structure by the atomic force microscopy, field emission scanning electron microscopy, and energy dispersive spectroscopy. A sophisticated computing model consisting of the Runge–Kutta method followed by Richardson extrapolation was applied in this investigation to solve the extended Nernst–Planck equations, which govern the solute particles’ transport across the active layer of NF-PANZr. A smart, adaptive step-size routine is chosen for this simple and robust method, also known as RK4 (fourth-order Runge–Kutta). The NF-PANZr membrane was less performant toward monovalent ions, and its rejection rate for multivalent ions reached 99.3%. The water flux of the NF-PANZr membrane was as high as 58 L · m⁻² · h⁻¹. Richardson’s extrapolation was then used to get a better approximation of Cl⁻ and Mg²⁺ rejection, the relative errors were, respectively, 0.09% and 0.01% for Cl⁻ and Mg²⁺. While waiting for the rise and expansion of machine learning in the prediction of rejection performance, we strongly recommend the development of better NF models and further validation of existing ones.

Chemically Tailored Multifunctional Asymmetric Isoporous Triblock Terpolymer Membranes for Selective Transport

Membrane-based separation of organic molecules with 1-2 nm lateral dimensions is a demanding but rather underdeveloped technology. The major challenge is to fabricate membranes having distinct nanochannels with desired functionality. Here, a bottom-up strategy to produce such a membrane using a tailor-made triblock terpolymer featuring miscible end blocks with two different functional groups is demonstrated. A scalable multifunctional integral asymmetric isoporous membrane is fabricated by the solvent evaporation-induced self-assembly of the block copolymer combined with nonsolvent-induced phase separation. The membrane nanopores are readily functionalized using positively and negatively charged moieties by two straightforward gas-solid reactions. The pores of the post-functionalized membranes act as target-specific functional soft nanochannels due to swelling of the polyelectrolyte blocks in a hydrated state. The membranes show unprecedented separation selectivity of small molecules based on size and/or charge which demonstrates the potential of the proposed strategy to prepare next-generation nanofiltration membranes.

Electrokinetic Characterization of Natural Stones Coated with Nanocomposites for the Protection of Cultural Heritage

Protective coatings, in recent years also from nanocomposite formulations, are commonly applied onto architectural stone and stone artefacts, mainly to prevent absorption of condensed water and dissolved atmospheric pollutants into the porous stone structure. While standard protocols to assess a coating’s performance are available, understanding the response of the coating-stone system is a complex task, due to the interplay of various factors determining the overall behaviour. Characterization techniques allowing one to correlate the extent and nature of surface modification upon treatment with the most relevant physical properties (i.e., water absorption and surface wettability) are thus of great interest. Electrokinetic analysis based on streaming current measurements, thanks to its sensitivity towards even minor changes in the surface chemical composition, may fulfil such requirement. Indeed, by involving the interaction with a testing aqueous electrolyte solution, this technique allows one to probe not only the outer surface, but also the outermost layer of the pore network, which plays a crucial role in the interaction of the stone with condensed atmospheric water. In this work, a correlation was found between the extent of surface modification, as determined by streaming current measurements, surface wettability and capillary water absorption, for three lithotypes with different mineralogical and microstructural properties treated with two nanocomposite formulations (one water based and one in alcoholic solvent) containing organosilica precursors and titania nanoparticles.

Effect of Geometry on Electrokinetic Characterization of Solid Surfaces

An analytical approach is presented to describe pressure-driven streaming current (I_str) and streaming potential (U_str) generation in geometrically complex samples, for which the classical Helmholtz-Smoluchowski (H-S) equation is known to be inaccurate. The new approach is valid under the same prerequisite conditions that are used for the development of the H-S equation, that is, the electrical double layers (EDLs) are sufficiently thin and surface conductivity and electroviscous effects are negligible. The analytical methodology is developed using linear velocity profiles to describe liquid flow inside of EDLs and using simplifying approximations to describe macroscopic flow. At first, a general expression is obtained to describe the I_str generated in different cross sections of an arbitrarily shaped sample. Thereafter, assuming that the generated U_str varies only along the pressure-gradient direction, an expression describing the variation of generated U_str along the sample length is obtained. These expressions describing I_str and U_str generation constitute the theoretical foundation of this work, which is first applied to a set of three nonuniform cross-sectional capillaries and thereafter to a square array of cylindrical fibers (model porous media) for both parallel and transverse fiber orientation cases. Although analytical solutions cannot be obtained for real porous substrates because of their random structure, the new theory provides useful insights into the effect of important factors such as fiber orientation, sample porosity, and sample dimensions. The solutions obtained for the model porous media are used to device strategies for more accurate zeta potential determination of porous fiber plugs. The new approach could be thus useful in resolving the long-standing problem of sample geometry dependence of zeta potential measurements.

Impact of Porosity and Electrolyte Composition on the Surface Charge of Hydroxyapatite Biomaterials

The success or failure of a material when implanted in the body is greatly determined by the surface properties of the material and the host tissue reactions. The very first event that takes place after implantation is the interaction of soluble ions, molecules and proteins from the biological environment with the material surface leading to the formation of an adsorbed protein layer that will later influence cell attachment. In this context, the particular topography and surface charge of a material become critical as they influence the nature of the proteins that will adsorb. However, very limited information is available on the surface charge of porous substrates. Only until very recently was the determination of the zeta potential on porous membranes accurately determined. The goal of this work was to implement the previous findings for the determination of the zeta potential of a series of porous hydroxyapatite (HA) substrates and to assess how porosity affects the measurements. In addition, studies using various electrolytes were also performed to prove how the specific affinity of certain ions for HA can further impact surface charge. The results showed that all materials exhibited very similar external surface charge (approximately -23 mV), consistent with their almost identical topographies. However, the presence of interconnected pores underneath the sample surface resulted in an additional internal zeta potential that varied with the porosity content. Measurements with different electrolytes confirmed the selectivity of divalent ions for HA underlying the importance of testing biomaterials using relevant electrolytes.

Facile real-time evaluation of the stability of surface charge under regular shear stress by pulsed streaming potential measurement

The applicability of the pulsed streaming potential measurement for real-time evaluation of stability of assembled layers based on the relative zeta potential change rate S_R was demonstrated.

Degradation of poly(ether sulfone)/polyvinylpyrrolidone membranes by sodium hypochlorite: insight from advanced electrokinetic characterizations

Poly(ether sulfone) (PES)/polyvinylpyrrolidone (PVP) membranes are widely used in various industrial fields such as drinking water production and in the dairy industry. However, the use of oxidants to sanitize the processing equipment is known to impair the integrity and lifespan of polymer membranes. In this work we showed how thorough electrokinetic measurements can provide essential information regarding the mechanism of degradation of PES/PVP membranes by sodium hypochlorite. Tangential streaming current measurements were performed with ultrafiltration and nanofiltration PES/PVP membranes for various aging times. The electrokinetic characterization of membranes was complemented by FTIR-ATR spectroscopy. Results confirmed that sodium hypochlorite induces the degradation of both PES and PVP. This latter is easily oxidized by sodium hypochlorite, which leads to an increase in the negative charge density of the membrane due to the formation of carboxylic acid groups. The PVP was also found to be partly released from the membrane with aging time. Thanks to the advanced electrokinetic characterization implemented in this work it was possible for the first time to demonstrate that two different mechanisms are involved in the degradation of PES. Phenol groups were first formed as a result of the oxidation of PES aromatic rings by substitution of hydrogen by hydroxyl radicals. For more severe aging conditions, this membrane degradation mechanism was followed by the formation of sulfonic acid functions, thus indicating a second degradation process through scission of PES chains.