A novel composite nanofiltration membrane prepared with PHGH and TMC by interfacial polymerization

Microstructure optimization of bioderived polyester nanofilms for antibiotic desalination via nanofiltration

The successful implementation of thin-film composite membranes (TFCM) for challenging solute-solute separations in the pharmaceutical industry requires a fine control over the microstructure (size, distribution, and connectivity of the free-volume elements) and thickness of the selective layer. For example, desalinating antibiotic streams requires highly interconnected free-volume elements of the right size to block antibiotics but allow the passage of salt ions and water. Here, we introduce stevioside, a plant-derived contorted glycoside, as a promising aqueous phase monomer for optimizing the microstructure of TFCM made via interfacial polymerization. The low diffusion rate and moderate reactivity of stevioside, together with its nonplanar and distorted conformation, produced thin selective layers with an ideal microporosity for antibiotic desalination. For example, an optimized 18-nm membrane exhibited an unprecedented combination of high water permeance (81.2 liter m^-2 hour^-1 bar^-1), antibiotic desalination efficiency (NaCl/tetracycline separation factor of 11.4), antifouling performance, and chlorine resistance.

Organic solvent-free constructing of stable zeolitic imidazolate framework functional layer enhanced by halloysite nanotubes and polyvinyl alcohol on polyvinylidene fluoride hollow fiber membranes for treating dyeing wastewater

In this study, zeolitic imidazolate framework (ZIF-8)/polyvinylidene fluoride (PVDF) loose nanofiltration (NF) hollow fiber membranes were fabricated by constructing ZIF-8 functional layer on the PVDF supporting membranes based on the vacuum-assisted assembly process. The ZIF-8 synthesis was completed in a water system, and the synthesized ZIF-8 suspension was directly added to polyvinyl alcohol (PVA) and halloysite nanotubes (HNTs) aqueous solution system without drying to prepare the casting solution, which could solve the agglomeration and poor dispersion problem of ZIF-8 particles. In addition, the embedded HNTs and the loaded PVA among the ZIF-8 layer could improve the bonding strength between the ZIF-8 layer and the supporting membranes. After constructing ZIF-8 functional layer, the pore size of supporting membranes decreased from more than 300 nm to several nanometers. Furthermore, the water contact angle reduced from 91.1° to 54.2°. Applied to treat dye wastewater, the prepared ZIF-8/PVDF membranes maintained high dye rejection (˃99.0 %) for Congo red (CR), but low salt rejection for NaCl (about 2 %). In addition, the flux could reach 21.6 L m^-2h^-1 after continuous filtration 360 min, exhibiting a potential for treating the dye/salt wastewater. In particular, there were no organic solvents used in the work, which provided a promising idea for solvent-free fabrication of loose NF membranes.

Advancing Strategies of Biofouling Control in Water-Treated Polymeric Membranes

Polymeric membranes, such as polyamide thin film composite membranes, have gained increasing popularity in wastewater treatment, seawater desalination, as well as the purification and concentration of chemicals for their high salt-rejection and water flux properties. Membrane biofouling originates from the attachment or deposition of organic macromolecules/microorganisms and leads to an increased operating pressure and shortened service life and has greatly limited the application of polymeric membranes. Over the past few years, numerous strategies and materials were developed with the aim to control membrane biofouling. In this review, the formation process, influence factors, and consequences of membrane biofouling are systematically summarized. Additionally, the specific strategies for mitigating membrane biofouling including anchoring of hydrophilic monomers, the incorporation of inorganic antimicrobial nanoparticles, coating/grafting of cationic bactericidal polymers, and the design of multifunctional material integrated multiple anti-biofouling mechanisms, are highlighted. Finally, perspectives on the challenges and opportunities in anti-biofouling polymeric membranes are shared, shedding light on the development of even better anti-biofouling materials in near future.

The synthesis of an amended membrane coated with graphene oxide and dopamine and guanidyl-based modifier and its antifouling properties

The membrane fouling issue has aroused great concern. To improve their antifouling properties, surface grafting with oxidative deposition were employed to amend a polyvinylidene fluoride (PVDF) membrane. The modifiers were amino-modified graphene oxide (AMGO), dopamine (DPA) and 1,3-diaminoguanidine hydrochloride (DAGH). To take bovine serum albumin (BSA, 1 g/l) as an example of organic materials, BSA interception rate and pure water flux recovery rate increased to 93.65% and 66.74%, respectively, while the corresponding values for the original membrane were much lower (72.82% and 31.72%). The optimum synthesis conditions were found to be 1.5 mg/ml of DPA, 1 wt% of DAGH, 2 mg/ml of AMGO, 4 h of DPA oxidation deposition time and 1 h of AMGO grafting time. Many functional groups like C = N, -NH₂, C = O and -OH improved the membrane surface hydrophilicity leading to a higher resistance to organic pollution. Dopamine and guanidyl facilitated the antimicrobial performance of the modified membrane, whose antimicrobial rate was up to 96%, while the raw membrane had no antimicrobial activity. The amended membrane possessed 40% higher mechanical strength than the initial one. It could withstand a high pumping suction force. The noteworthy property was that the irreversible fouling rate decreased by 55%. Therefore, the amended membrane could restore its flux much more easily.

Multi-ionic electrolytes and E.coli removal from wastewater using chitosan-based in-situ mediated thin film composite nanofiltration membrane

This work presents the experimental investigation of flat sheet composite nanofiltration membrane synthesized with chitosan nanoparticles through interfacial polymerization of piperazine with trimesoyl chloride on polyethersulfone/sulfonated polysulfone substrates. The synthesized membrane was tested in wastewater treatment containing inorganic salts and E.Coli. Single binary electrolyte solution of KCl, MgCl₂, MgSO_4, and Na₂SO₄, ternary electrolyte solution, containing a combination of MgCl₂ and MgSO₄, KCl and MgCl₂ and quaternary electrolyte solution of KCl, MgCl_2, and MgSO₄ as feed were treated in crossflow membrane cell for the water flux and species rejection in the permeate under operating pressure up to 0.5 MPa. The rejection of Na¹⁺, K¹⁺, Mg²⁺, Cl^1-, and SO₄^2- was observed to be 81, 28, 87, 96, and 98%, respectively with an average water flux up to 214 ± 10 L m⁻².hr⁻¹ in the permeate for the binary electrolyte solution. Similarly, the rejection for K¹⁺, Mg²⁺, Cl^1- and SO₄^2- was noted to be 33, 94, 97, and 99%, respectively, for ternary electrolyte solution with an average water flux up to 211 ± 10 L m^-2.hr^-1. The quaternary ion system in the feed resulted in an average water flux up to 198 ± 12 L m⁻².hr⁻¹ with the rejection of K⁺, Mg⁺², Cl^- and SO₄^-2 as 35, 87, 96, and 99%, respectively. The model feed solution of E. coli after passing through the membrane achieved an E. coli rejection (99%) with water flux up to 220 L m^-2.hr^-1.

Nanofiltration for Arsenic Removal: Challenges, Recent Developments, and Perspectives

Arsenic (As) removal is of major significance because inorganic arsenic is highly toxic to all life forms, is a confirmed carcinogen, and is of significant environmental concern. As contamination in drinking water alone threatens more than 150 million people all over the world. Therefore, several conventional methods such as oxidation, coagulation, adsorption, etc., have been implemented for As removal, but due to their cost-maintenance limitations; there is a drive for advanced, low cost nanofiltration membrane-based technology. Thus, in order to address the increasing demand of fresh and drinking water, this review focuses on advanced nanofiltration (NF) strategy for As removal to safeguard water security. The review concentrates on different types of NF membranes, membrane fabrication processes, and their mechanism and efficiency of performance for removing As from contaminated water. The article provides an overview of the current status of polymer-, polymer composite-, and polymer nanocomposite-based NF membranes, to assess the status of nanomaterial-facilitated NF membranes and to incite progress in this area. Finally, future perspectives and future trends are highlighted.

Enhanced permeability, mechanical and antibacterial properties of cellulose acetate ultrafiltration membranes incorporated with lignocellulose nanofibrils

Cellulose acetate (CA) ultrafiltration membranes are attracting more attention in wastewater purification due to its biodegradability and eco-friendly. The application of CA membranes, however, is limited by high susceptibility to bacterial corrosion and lack of mechanical tolerance that results in loss of life. To solve the above problems, we first fabricated the CA-based composite membranes incorporated with bamboo-based lignocellulose nanofibrils (LCNFs) by a strategy of phase inversion. LCNFs was prepared by using a combined method of one-step chemical pretreatment and acid hydrolysis coupled with high-pressure homogenization. The as-prepared CA/LCNFs composite membranes with 4 wt% lignin in the LCNFs exhibited high tensile strength of 7.08 MPa and strain-at-break of 12.21%, and high filtration permeability of 188.23 L·m^-2·h^-1 as ultrafiltration membranes for wastewater treatment, which could obviously inhibit the growth of Escherichia coli.

Tris(hydroxymethyl)aminomethane-grafted polyamine nanofiltration membrane: enhanced antifouling and pH resistant properties

In this study, to fabricate a pH resistant membrane with antifouling properties, a Tris-grafted polyamine thin film composite (TFC) membrane has been synthesized.

Control of Membrane Fouling in Organics Filtration Using Ce-Doped Zirconia and Visible Light

Membrane fouling has been a major issue in the development of more efficient water treatment processes. Specifically in surface waters filtration, organic matter, such as humic-like substances, can cause irreversible fouling. Therefore, this study evaluates the activity of a photocatalytic layer composed of Ce-doped zirconia nanoparticles in improving the fouling resistance during filtration of an aqueous solution of humic acid (HA). These nanoparticles were prepared by hydrothermal and sol-gel processes and then characterized. Before the filtration experiments, the photodegradation of HA catalyzed by Ce-doped zirconia nanoparticles in dispersion was studied. It was observed that the sol-gel prepared Ce-ZrO₂ exhibited higher HA removal in practically neutral pH, achieving 93% efficiency in 180 min of adsorption in the dark followed by 180 min under visible-light irradiation using light-emitting diodes (LEDs). Changes in spectral properties and in total organic carbon confirmed HA degradation and contributed to the proposal of a mechanism for HA photodegradation. Finally, in HA filtration tests, Ce-ZrO₂ photocatalytic membranes were able to recover the flux in a fouled membrane using visible-light by degrading HA. The present findings point to the further development of anti-fouling membranes, in which solar light can be used to degrade fouling compounds and possibly contaminants of emerging concern, which will have important environmental implications.

Porous metal–organic molecular cage: a promising candidate to highly improve the nanofiltration performance of thin film nanocomposite membranes

Novel PA/Fe-cage TFN membranes with improved nanofiltration performance were successfully fabricated by incorporating porous Fe-cages during the IP process.

Sulfaguanidine nanofiltration active layer towards anti-adhesive and antimicrobial attributes for desalination and dye removal

A novel sulfaguanidine (SG)-modified polyamide thin-film composite (TFC) nanofiltration (NF) membrane was constructed by the strategy referred to as co-solvent assisted interfacial polymerization (CASIP), which involves the respective interfacial polymerization (IP) of piperazine (PIP) and SG with trimesoyl chloride (TMC) on porous polysulfone (PSf) supports. CASIP enables the formation of a defect-free thin dense active layer and favors higher water permeance up to 79.0 L m⁻² h⁻¹ with rejection above 98.3% for Na₂SO₄. The resulting PA membrane also demonstrates a high flux recovery ratio of nearly 98.9% to bovine serum albumin protein after being cleaned. More importantly, the current membrane shows excellent anti-adhesive and antimicrobial performances against Gram-negative Escherichia coli, Gram-positive Bacillus pumilus LDS.33 and Aspergillus parasiticus JFS. This promises great potential application of the PA membrane for practical water/wastewater treatment. The prospect of using the co-solvent mediated SG-modified layer as a next-generation anti-fouling/antimicrobial membrane is very encouraging.

The resulting sulfaguanidine nanofiltration membrane demonstrates higher water permeance and better antifouling property. The membrane shows excellent anti-adhesive and antimicrobial performances against E. coli, B. pumilus LDS.33 and A. parasiticus JFS.

An acid-stable positively charged polysulfonamide nanofiltration membrane prepared by interfacial polymerization of polyallylamine and 1,3-benzenedisulfonyl chloride for water treatment

Here, we selected macromolecular polyallylamine (PAH) as the monomer in an aqueous-phase reaction for the first time, which underwent interfacial polymerization with 1,3-benzenedisulfonyl chloride (BDSC) on the surface of a polyethersulfone (PES) ultrafiltration membrane to prepare a new PSA composite membrane with positive charge, acid stability and high separation performance. By tailoring the polymerization conditions, the desired PSA composite membrane exhibited excellent rejection of different salts [MgCl₂ (92.44%) > MgSO₄ (89.2%) > NaCl (56.8%) > Na₂SO₄ (55.2%)] and a high permeation flux of up to 34.10 L m⁻² h⁻¹ at 0.5 MPa. The properties of the membrane were evaluated using various characterization techniques. The results indicated that the new PSA membrane is more positively charged and more compact than reported PSA composite membranes. In addition, it exhibited high acid stability. After exposure to a 20% (w/v) H₂SO₄ solution for 30 days, the MgCl₂ rejection level reached 88.3%. Finally, we used the new PSA composite membrane to test some heavy metal ions and found that the rejection level was always greater than 90%. Therefore, the new PSA composite membrane exhibited potential for water desalination and the removal of heavy metal ions from an acidic environment.

Here, an acid stable PSA membrane with positively charge was prepared through the IP between macromolecular PAH and BDSC on PES substrate. In addition, the PSA membrane exhibited excellent separation performance to divalent metal ions.

Ultrathin Polyamide Membrane with Decreased Porosity Designed for Outstanding Water-Softening Performance and Superior Antifouling Properties

Poly(piperazine-amide)-based nanofiltration membranes exhibit a smooth surface and superior antifouling properties but often have lower Ca²⁺ and Mg²⁺ rejection due to their larger inner micropore and thus cannot be extensively used in water-softening applications. To decrease the pore size of poly(piperazine-amide) membranes, we designed and synthesized a novel monomer, 1,2,3,4-cyclobutane tetracarboxylic acid chloride (BTC), which possesses a smaller molecular conformation than trimesoyl chloride (TMC). The thickness of the prepared BTC-piperazine (PIP) polyamide nanofilm via interfacial polymerization is as thin as 15 nm, significantly lower than the 50 nm thickness of the TMC-PIP nanofilm. The surface characterization reveals that the BTC-PIP polyamide membrane exhibits an enhanced hydrophilicity, a smooth surface, and a decreased surface-negative charge. The desalination performance (both rejection and water flux) of these membranes in terms of Ca²⁺ and Mg²⁺ exceeds that of the current commercial water-softening membranes. In addition, the BTC-PIP polyamide membrane also exhibits superior antifouling properties compared to the TMC-based polyamide membrane. More importantly, molecular simulations show that the BTC-PIP membrane has a lower average pore size than that of the TMC-PIP membrane, which demonstrates an enhanced steric hindrance effect, as confirmed by desalination performance. Our results demonstrate that in the household and industrial water-softening market, BTC-PIP membrane with decreased porosity, enhanced hydrophilicity, and smooth surface is preferred alternative to the conventional TMC-based polyamide membranes.

Antifouling membranes for sustainable water purification: strategies and mechanisms

One of the greatest challenges to the sustainability of modern society is an inadequate supply of clean water. Due to its energy-saving and cost-effective features, membrane technology has become an indispensable platform technology for water purification, including seawater and brackish water desalination as well as municipal or industrial wastewater treatment. However, membrane fouling, which arises from the nonspecific interaction between membrane surface and foulants, significantly impedes the efficient application of membrane technology. Preparing antifouling membranes is a fundamental strategy to deal with pervasive fouling problems from a variety of foulants. In recent years, major advancements have been made in membrane preparation techniques and in elucidating the antifouling mechanisms of membrane processes, including ultrafiltration, nanofiltration, reverse osmosis and forward osmosis. This review will first introduce the major foulants and the principal mechanisms of membrane fouling, and then highlight the development, current status and future prospects of antifouling membranes, including antifouling strategies, preparation techniques and practical applications. In particular, the strategies and mechanisms for antifouling membranes, including passive fouling resistance and fouling release, active off-surface and on-surface strategies, will be proposed and discussed extensively.

Synthesis and antibacterial properties of a novel magnetic nanocomposite prepared from spent pickling liquors and polyguanidine

Magnetic nanoparticles have received much interest for their application in wastewater treatment because of their easy retrieval and reuse. However, the methods used to synthesise high saturation magnetization magnetic nanoparticles require expensive and pure precursors. In the current study, we explore the potential for using spent pickling liquor, a wastewater solution from steel factories, as the iron precursor for preparing iron oxide nanoparticles. Here, magnetic Fe₃O₄ nanoparticles were synthesized via the oxidation–precipitation of spent pickling liquors using a saturated solution of calcium hydroxide at room temperature. The Fe₃O₄ nanoparticles were then modified with antibacterial polyguanidine to form a nanocomposite. It was found that monodisperse magnetic Fe₃O₄ nanoparticles with a size in the range 20–30 nm and a high saturation magnetization value of 73.9 emu g⁻¹ were synthesised. The Fe₃O₄ nanoparticles were successfully encapsulated with polyguanidine to form an Fe₃O₄/polyguanidine nanocomposite. FT-IR and TGA analysis results indicated the presence of the polymer on the Fe₃O₄ surface and the polymer content in the nanocomposite was about 15% (w/w). The Fe₃O₄/polyguanidine nanocomposite exhibited strong antibacterial activity against Escherichia coli (E. coli), demonstrating its potential for use in disinfecting wastewater.

An Fe₃O₄/polyguanidine nanocomposite with strong antibacterial activity was prepared from Fe₃O₄ nanoparticles, using spent pickling liquors as the iron source, which were then encapsulated with polyguanidine.

Biguanidine functional chitooligosaccharide modified reverse osmosis membrane with improved anti-biofouling property

The COSG-modified RO membrane with excellent anti-adhesive and antimicrobial properties was successfully fabricated by second interfacial polymerization.

Hydrophilic and antimicrobial core–shell nanoparticles containing guanidine groups for ultrafiltration membrane modification

Physical blending is a common technique to improve the water flux and antifouling performance of ultrafiltration (UF) membranes. In the present work, a novel hydrophilic and antimicrobial core–shell nanoparticle was synthesized through the chemical grafting of poly(guanidine-hexamethylenediamine-PEI) (poly(GHPEI)) on the surface of silica nanoparticles (SNP). The synthesized core–shell nanoparticles, poly(GHPEI) functionalized silica nanoparticles (SNP@PG), were incorporated into polyethersulfone (PES) to fabricate hybrid UF membranes by a phase inversion process. The chemical composition, surface and cross section morphologies, hydrophilicity, water flux and protein rejection of the membranes were evaluated by a series of characterizations. Results show that the prepared PES/SNP@PG hybrid membrane exhibits not only improved water flux, which is around 2.6 times that of the pristine PES membrane, but also excellent resistance to organic fouling and biofouling.

Hydrophilic and antimicrobial core–shell nanoparticles containing guanidine groups (SNP@PG) were applied to fabricate membranes with improved water flux and fouling resistance.

Graphene Oxide Quantum Dots Incorporated into a Thin Film Nanocomposite Membrane with High Flux and Antifouling Properties for Low-Pressure Nanofiltration

Graphene oxide quantum dots (GOQDs), novel carbon-based nanomaterials, have attracted tremendous research interest due to their unique properties associated with both graphene and quantum dots. In the present study, thin film nanocomposite (TFN) membranes comprising GOQDs dispersed within a tannic acid (TA) film were fabricated by an interfacial polymerization reaction for low-pressure nanofiltration (NF). The resultant TA/GOQDs TFN membranes had measurably smoother and more hydrophilic, negatively charged surfaces compared to the similarly formed TA thin film composite (TFC) membrane. Owing to the loose active layer structure and the combination of Donnan exclusion and steric hindrance, the TA/GOQDs TFN membrane showed a pure water flux up to 23.33 L/m²·h (0.2 MPa), which was 1.5 times more than that of pristine TA TFC membrane, while high dye rejection to Congo red (99.8%) and methylene blue (97.6%) was kept. In addition, the TA/GOQDs TFN membrane presented better antifouling properties, which was ascribed to the favorable changes in membrane hydrophilicity, ζ-potential, and surface roughness. These results indicated the great potential of such membranes in wastewater treatment, separation, and purification in many industrial fields.

Antifouling sulfonated polyamide nanofiltration hollow fiber membrane prepared with mixed diamine monomers of BDSA and PIP

A novel high-flux sulfonated polyamide nanofiltration (NF) hollow fiber membrane was made from the mixed monomers of 2,2′-benzidinedisulfonic acid (BDSA) and piperazine (PIP).

Fabrication and characterization of a novel nanofiltration membrane by the interfacial polymerization of 1,4-diaminocyclohexane (DCH) and trimesoyl chloride (TMC)

A novel thin-film composite polyamide membrane for nanofiltration is prepared, and the addition of sodium N-cyclohexylsulfamate is found to have a significant influence on its performance.