An integration of photo-Fenton and membrane process for water treatment by a PVDF@CuFe2O4 catalytic membrane

Thin-Layer TiO2 Membrane Fabrication by Condensed Layer Deposition

A novel approach to the fabrication of thin-film supported metal oxide membranes was investigated. Nanocoatings were obtained by the condensed layer deposition of TiO2 on tubular microporous supports, applying multiple consecutive layers of TiO2/polyaniline. The surface, cross-sectional structure, and morphology of the materials were investigated by electron microscopy. Their membrane-related properties were explored by permeability measurements, rejection, and fouling analysis, using polyethylene glycol (PEG) as test molecules. The SEM images showed that TiO2 was successfully deposited on the surface, creating a layer with partial coverage of the support after each layer was deposited; consequently, the permeability of the membranes decreased gradually. Overall, the results of the flux and permeability of the membranes confirmed the coating. The transmembrane pressure (TMP) increased with each coating layer, while the rejection of the membrane showed gradual improvement.

Construction of self-cleaning g-C3N4/Bi2MoO6/PVDF membrane and coupling with photo-Fenton-like reaction for sustainable removal of antibiotics in wastewater

Constructing a photocatalytic membrane and photo-Fenton reaction coupling system is a novel strategy to enhance the photocatalytic activity of the membrane and eliminate the problem of membrane contamination. Herein, a g-C3N4/Bi2MoO6/PVDF photocatalytic membrane was prepared using a tannic acid-assisted in-situ deposition method. The membrane was characterized by three advantages of photocatalytic, self-cleaning, and antibacterial properties. Under the photo-Fenton-like conditions, the membrane had superior photodegradation efficiency of 90.7% for tetracycline, one of the main antibiotic contaminants in the China's aquatic system. Moreover, the membrane had excellent photo-Fenton self-cleaning ability, its flux recovery rate was up to 96%-98% after the self-cleaning process. Photoluminescence spectra, diffuse UV-visible spectrum, transient photocurrent responses, and electrochemical AC impedance spectrum results show that the heterojunction structure formed by g-C3N4 and Bi2MoO6 could improve the separation efficiency of photogenerated electrons-hole pairs. Electron spin resonance spectroscopy confirmed the photo-electrons facilitated the formation of hydroxyl radical (·OH) in the existence of H2O2, which enhanced tetracycline degradation. Moreover, the superior photo-Fenton self-cleaning performance, which mainly relied on the active free radicals produced by the photo-Fenton-like membrane to remove dirt on the membrane surface or in the membrane pore channel. Our results may shed new light on the development of promising photocatalytic membrane systems by coupling with photo-Fenton-like processes, and facilitate their applications for wastewater treatment.

Simultaneous enhanced antibiotic pollutants removal and sustained permeability of the membrane involving CoFe2O4/MoS2 catalyst initiated with simple H2O2 backwashing

Membranes for wastewater treatment should ideally exhibit sustainable high permeate production, enhanced pollutant removal, and intrinsic physical rejection. In this study, CoFe2O4/MoS2 serves as a non-homogeneous phase catalyst; it is combined with polyether sulfone membranes via liquid-induced phase separation to simultaneously sustain membrane permeability and enhance antibiotic pollutant degradation. The prepared catalytic membranes have higher pure water flux (329.34 L m-2 h-1) than pristine polyethersulfone membranes (219.03 L m-2 h-1), as well as higher mean pore size, porosity, and hydrophilicity. Under a moderate transmembrane pressure (0.05 MPa), tetracycline (TC) in synthetic and real wastewater was degraded by the optimal catalytic membrane by 72.7 % and 91.2 %, respectively. Owing to the generation of the reactive oxygen species (ROS) during the Fenton-like reaction process, the catalytic membrane could exclude the natural organics during the H2O2 backwash step and selectively promote fouling degradation in the membrane channel. The irreversible fouling ratio of the catalyzed membrane was significantly reduced, and the flux recovery rate increased by up to 91.6 %. A potential catalytic mechanism and TC degradation pathways were proposed. This study offers valuable insights for designing catalytic membranes with enhanced filtration performance.

Robust fabrication of sulfonated graphene oxide/poly (ether sulfone) catalytic membrane reactor for efficient cellulose hydrolysis and product separation

The efficient conversion of cellulose to high value-added products is important for the utilization of cellulose biomass. Achieving efficient cellulose hydrolysis and timely products separation is the essential target. Herein, a modified sulfonated graphene oxide/polydopamine deposited polyethersulfone (mGO(SO3H)-PDA/PES) membrane reactor, combining in the same unit a conversion effect and a separation effect, was prepared by suction filtration and subsequent polymerization and adhesion. The structure of PES membrane and deposition of PDA was regulated to sure that small molecules can pass through the membrane, while cellulose could not. As a result, the mGO(SO3H)-PDA/PES membrane realized the efficient cellulose hydrolysis and timely products separation under cross-flow circulation mode at 0.1 MPa, avoiding the further degradation of reducing sugar products. The yields of total reducing sugar (TRS) and glucose in separated hydrolysate reached 93.2 % and 85.5 %, respectively. This strategy provides potential guidance for efficient conversion of cellulose.

Membrane processes enhanced by various forms of physical energy: A systematic review on mechanisms, implementation, application and energy efficiency

Membrane technologies in water and wastewater treatment have been eagerly pursued over the past decades, yet membrane fouling remains the major bottleneck to overcome. Membrane fouling control methods which couple membrane processes with online in situ application of external physical energy input (EPEI) are getting closer and closer to reality, thanks to recent advances in novel materials and energy deliverance methods. In this review, we summarized recent studies on membrane fouling control techniques that depend on (i) electric field, (ii) acoustic field, (iii) magnetic field, and (iv) photo-irradiation (mostly ultraviolet or visible light). Mechanisms of each energy input were first reported, which defines the applicability of these methods to certain wastewater matrices. Then, means of implementation were discussed to evaluate the compatibility of these fouling control methods with established membrane techniques. After that, preferred applications of each energy input to different foulant types and membrane processes in the experiment reports were summarized, along with a discussion on the trends and knowledge gaps of such fouling control research. Next, specific energy consumption in membrane fouling control and flux enhancement was estimated and compared, based on the experimental results reported in the literature. Lastly, strength and weakness of these methods and future perspectives were presented as open questions.

Application of Photo-Fenton-Membrane Technology in Wastewater Treatment: A Review

Photo-Fenton coupled with membrane (photo-Fenton-membrane) technology offers great potential benefits in future wastewater treatment because it can not only degrade refractory organics, but also separate different pollutants from water; additionally, it often has a membrane-self-cleaning ability. In this review, three key factors of photo-Fenton-membrane technology, photo-Fenton catalysts, membrane materials and reactor configuration, are presented. Fe-based photo-Fenton catalysts include zero-valent iron, iron oxides, Fe-metal oxides composites and Fe-based metal-organic frameworks. Non-Fe-based photo-Fenton catalysts are related to other metallic compounds and carbon-based materials. Polymeric and ceramic membranes used in photo-Fenton-membrane technology are discussed. Additionally, two kinds of reactor configurations, immobilized reactor and suspension reactor, are introduced. Moreover, we summarize the applications of photo-Fenton-membrane technology in wastewater, such as separation and degradation of pollutants, removal of Cr(VI) and disinfection. In the last section, the future prospects of photo-Fenton-membrane technology are discussed.

Recent Advances in the Development of Novel Iron–Copper Bimetallic Photo Fenton Catalysts

Advanced oxidation processes (AOPs) have been postulated as viable, innovative, and efficient technologies for the removal of pollutants from water bodies. Among AOPs, photo-Fenton processes have been shown to be effective for the degradation of various types of organic compounds in industrial wastewater. Monometallic iron catalysts are limited in practical applications due to their low catalytic activity, poor stability, and recyclability. On the other hand, the development of catalysts based on copper oxides has become a current research topic due to their advantages such as strong light absorption, high mobility of charge carriers, low environmental toxicity, long-term stability, and low production cost. For these reasons, great efforts have been made to improve the practical applications of heterogeneous catalysts, and the bimetallic iron–copper materials have become a focus of research. In this context, this review focuses on the compilation of the most relevant studies on the recent progress in the application of bimetallic iron–copper materials in heterogeneous photo–Fenton-like reactions for the degradation of pollutants in wastewater. Special attention is paid to the removal efficiencies obtained and the reaction mechanisms involved in the photo–Fenton treatments with the different catalysts.

Catalytic Membrane with Copper Single-Atom Catalysts for Effective Hydrogen Peroxide Activation and Pollutant Destruction

The superior catalytic property of single-atom catalysts (SACs) renders them highly desirable in the energy and environmental fields. However, using SACs for water decontamination is hindered by their limited spatial distribution and density on engineered surfaces and low stability in complex aqueous environments. Herein, we present copper SACs (Cu₁) anchored on a thiol-doped reactive membrane for water purification. We demonstrate that the fabricated Cu₁ features a Cu-S₂ coordination─one copper atom is bridged by two thiolate sulfur atoms, resulting in high-density Cu-SACs on the membrane (2.1 ± 0.3 Cu atoms per nm²). The Cu-SACs activate peroxide to generate hydroxyl radicals, exhibiting fast kinetics, which are 40-fold higher than those of nanoparticulate Cu catalysts. The Cu₁-functionalized membrane oxidatively removes organic pollutants from feedwater in the presence of peroxide, achieving efficient water purification. We provide evidence that a dual-site cascade mechanism is responsible for in situ regeneration of Cu₁. Specifically, one of the two linked sulfur atoms detaches the oxidized Cu₁ while donating one electron, and an adjacent free thiol rebinds the reduced Cu(I)-S pair, retrieving the Cu-S₂ coordination on the reactive membrane. This work presents a universal, facile approach for engineering robust SACs on water-treatment membranes and broadens the application of SACs to real-world environmental problems.

Modified Polyethersulfone Ultrafiltration Membrane for Enhanced Antifouling Capacity and Dye Catalytic Degradation Efficiency

Catalytic membranes, as a combination of heterogeneous advanced oxidation and membrane technology reaction systems, have important application prospects in the treatment of dyes and other organics. In practical applications, it is still challenging to construct catalytic membranes with excellent removal efficiency and fouling mitigation. Herein, molybdenum disulfide-iron oxyhydroxide (MoS2-FeOOH) was fabricated using iron oxide and MoS2 nanoflakes, which were synthesized by the hydrothermal method. Furthermore, by changing the concentration of MoS2-FeOOH, the MoS2-FeOOH/polyethersulfone (PES) composite ultrafiltration membrane was obtained with improved hydrophilicity, permeability, and antifouling capacity. The pure water flux of the composite membrane reached 385.3 L/(m2 h), which was 1.7 times that of the blank PES membrane. Compared with the blank membrane, with the increase of MoS2-FeOOH content, the MoS2-FeOOH/PES composite membranes had better adsorption capacity and catalytic performance, and the membrane with 3.0% MoS2-FeOOH content (M4) could be achieved at a 60.2% methylene blue (MB) degradation rate. In addition, the membrane flux recovery ratio (FRR) of the composite membrane also increased from 25.6% of blank PES membrane (M0) to more than 70% after two cycles of bovine serum albumin (BSA) filtration and hydraulic cleaning. The membrane with 2.25% MoS2-FeOOH content (M3) had the best antifouling performance, with the largest FRR and the smallest irreversible ratio (Rir). Catalytic self-cleaning of the composite membrane M3 recovered 95% of the initial flux with 0.1 mol/L H2O2 cleaning. The MoS2-FeOOH/PES composite membranes with the functions of excellent rejection and antifouling capacity have a good prospect in the treatment of printing and dyeing wastewater composed of soluble dyes.

Synergistic oxidation-filtration process of electroactive peroxydisulfate with a cathodic composite CNT-PPy/PVDF ultrafiltration membrane

Ultrafiltration is an advanced water treatment process which performs poorly in the removal of small molecule organic pollutants, and is susceptible to irreversible membrane fouling. In this study, a new carbon nanotube cross-linked polypyrrole composite ultrafiltration membrane (CNT-PPy/PVDF) was fabricated, and exhibited excellent conductivity, hydrophilicity, and permeability in a novel electro-filtration activated peroxydisulfate (PDS) system (EFAP) for cathodic electrochemical activation of PDS. The EFAP showed satisfactory performance in removal of series of small molecule organic pollutants (i.e., carbamazepine, sulfamethoxazole, phenol, diclofenac.) and stable removal ratio (remaining above 90% after 20 operating cycles). Further study proved the electric field could effectively protect the cathodic CNT-PPy/PVDF membrane from oxidative damage through continual free electrons injection. Besides, the EFAP achieved up to 95% flux recovery and 80% reduction of irreversible membrane fouling (bovine serum albumin as the model foulant). Moreover, experiments confirmed that the in situ generated ^•OH, SO₄^•-, and ¹O₂ were the main reactive oxygen species contributing to small organics removal, while the irreversible membrane fouling mitigation was mainly due to the electrical repulsion, SO₄^•- and ^•OH, rather than ¹O₂. This new type of EFAP may provide a promising and sustainable approach in organic emerging contaminants control in water treatment.

Fabrication of photo-Fenton self-cleaning PVDF composite membrane for highly efficient oil-in-water emulsion separation

The anti-fouling performance of membranes is an important performance in the separation of oil/water.

Efficient Fenton-Like Catalysis Boosting the Antifouling Performance of the Heterostructured Membranes Fabricated via Vapor-Induced Phase Separation and In Situ Mineralization

A photocatalytic membrane with significant degradation and antifouling performance has become an important part in wastewater treatment. However, the low catalyst loading on the polymer membrane limits its performance improvement. Herein, we fabricated poly(vinylidene fluoride) (PVDF) and poly(acrylic acid) (PAA) blend membranes with a rough surface via a vapor-induced phase separation (VIPS) process. Then Fe³⁺ was cross-linked with the carboxyl groups on the membrane surface and further in situ mineralized into β-FeOOH nanorods. The resultant membranes exhibit not only hydrophilicity and underwater superoleophobicity but also favorable separation efficiency and high water flux in oil-in-water emulsions separation. Under visible light irradiation, the membrane can degrade methylene blue (MB) to 95.2% in 180 min. More importantly, the membrane has a significant photocatalytic self-cleaning ability for crude oil with a flux recovery ratio (FRR) as high as 94.1%. This work brings a new strategy to fabricate the rough and porous surface for high loading of the hydrophilic photo-Fenton catalyst, improving the oil/water emulsion separation and antifouling performance of the membranes.

Catalytic membrane-based oxidation-filtration systems for organic wastewater purification: A review

Catalytic membranes can simultaneously realize physical separation and chemical oxidation in one integrated system, which is the frontier technology for effective removal of organic containments in wastewater treatment. The catalytic membrane coupled with advanced oxidation processes (AOPs) not only significantly enhances the pollutant removal efficiency but also inhibits the fouling of the membrane via self-cleaning. In this review, the preparation approaches of catalytic membranes including blending, surface coating, and bottom-up synthesis are comprehensively summarized. The different integrated catalytic membrane systems coupled with photocatalysis, Fenton oxidation, persulfate activations, ozonation and electrocatalytic oxidation are discussed in terms of mechanisms and performance. Besides, the principles, influencing factors, advantages and issues of the different catalytic membrane/oxidation systems are outlined comparatively. Finally, the future challenges, and research directions are suggested, which is conducive to the design and development of catalytic membrane-oxidation systems for practical remediation of organic containing wastewater.

Membrane-Confined Iron Oxychloride Nanocatalysts for Highly Efficient Heterogeneous Fenton Water Treatment

Heterogeneous advanced oxidation processes (AOPs) allow for the destruction of aqueous organic pollutants via oxidation by hydroxyl radicals (^•OH). However, practical treatment scenarios suffer from the low availability of short-lived ^•OH in aqueous bulk, due to both mass transfer limitations and quenching by water constituents, such as natural organic matter (NOM). Herein, we overcome these challenges by loading iron oxychloride catalysts within the pores of a ceramic ultrafiltration membrane, resulting in an internal heterogeneous Fenton reaction that can degrade organics in complex water matrices with pH up to 6.2. With ^•OH confined inside the nanopores (∼ 20 nm), this membrane reactor completely removed various organic pollutants with water fluxes of up to 100 L m^-2 h^-1 (equivalent to a retention time of 10 s). This membrane, with a pore size that excludes NOM (>300 kDa), selectively exposed smaller organics to ^•OH within the pores under confinement and showed excellent resiliency to representative water matrices (simulated surface water and sand filtration effluent samples). Moreover, the membrane exhibited sustained AOPs (>24 h) and could be regenerated for multiple cycles. Our results suggest the feasibility of exploiting ultrafiltration membrane-based AOP platforms for organic pollutant degradation in complex water scenarios.

Controllable synthesis and characterization of Mg2SiO4 nanostructures via a simple hydrothermal route using carboxylic acid as capping agent and their photocatalytic performance for photodegradation of azo dyes

Magnesium silicate (forsterite) nanoparticles were synthesized by a facile hydrothermal method, and characterized using several techniques such as XRD, SEM, EDS, DRS, Raman, TEM, and FT-IR. Several carboxylic acid structures were applied to modify the morphology and surface properties of the as-prepared particles. In this manuscript, citric acid, maleic acid, and succinic acid were used as the carboxylic acid agents. The effect of changing the ratio of carboxylic acid agent to central metal on the morphology and photocatalytic behavior was evaluated. The activities of the Mg₂SiO₄ nanostructures as photocatalysts were assessed by the degradation of several azo dyes (Acid Blue 92, Acid Brown 14, and Acid Violet 7) under UV and Vis light irradiation. The degradation percentages of Acid Blue 92 were about 88% and 74% in the presence of Vis and UV light respectively, and the percentages for photodegradation of Acid Brown 14 were approximately 76% and 82% in the presence of Vis and UV light, respectively. Furthermore, the degradation percentages for Acid Violet 7 were 93% and 80% under UV and Vis light, respectively.

Mg₂SiO₄ nanostructures have been synthesized via a facile hydrothermal approach. The photocatalytic behavior of Mg₂SiO₄ nanostructures prepared by different carboxylic acids have been investigated to degrade azo dyes under UV and visible light.

The Influence of Photocatalytic Reactors Design and Operating Parameters on the Wastewater Organic Pollutants Removal—A Mini-Review

The organic pollutants removal by conventional methods (adsorption, coagulation, filtration, microorganism and enzymes) showed important limitation due to the reluctance of these molecules. An alternative to this issue is represented by the photocatalytic technology considered as an advanced oxidation process (AOP). The photoreactors design and concepts vary based on the working regime (static or dynamic), photocatalyst morphology (powders or bulk) and volume. This mini-review aims to provide specific guidelines on the correlations between the photoreactor concept characteristics (working regime, volume and flow rate), irradiation scenarios (light spectra, irradiation period and intensity) and the photocatalytic process parameters (photocatalyst materials and dosage, pollutant type and concentration, pollutant removal efficiency and constant rate). The paper considers two main photoreactor geometries (cylindrical and rectangular) and analyses the influence of parameters optimization on the overall photocatalytic efficiency. Based on the systematic evaluation of the input data reported in the scientific papers, several perspectives regarding the photocatalytic reactors’ optimization were included.

Preparation of PVDF/CdS/Bi2WO6/ZnO hybrid membrane with enhanced visible-light photocatalytic activity for degrading nitrite in water

In this work, a visible light-driven ternary heterojunction photocatalyst, CdS/Bi₂WO₆/ZnO, was synthesized using hydrothermal, ultrasonic dispersion, and deposition precipitation methods. The results show that photocatalysts with flower-like heterostructures were obtained, which could efficiently separate electron-hole pairs, and the photocatalytic activity was thereby significantly enhanced. Furthermore, CdS/Bi₂WO₆/ZnO and polyvinylidene fluoride (PVDF) were used to fabricate hybrid membranes via a phase-conversion method. The samples were characterized using SEM, TEM, EDX, XRD, DRS, XPS, PL, and N₂ adsorption-desorption isotherms, and the transient photocurrent response. The photocatalytic activity of the hybrid membrane was evaluated, and 92.58% of the nitrite was converted into non-toxic substances within 4 h under simulated sunlight irradiation. This result indicated that the photocatalyst exhibited a good photocatalytic activity after immobilization. The possible mechanism was elucidated by studying the product during the photocatalytic degradation, and the effects of different pH values, electron scavengers, and hole scavengers on the photocatalytic performance were further investigated.

Polyacrylonitrile homogeneous blend hollow fiber membrane with stable structure as a substrate to support Fe/Mn oxide and its enhanced capability to purify dye wastewater

Blending different molecular weight polyacrylonitrile (PAN) was adopted to solve the shrinkage problem of high molecular weight PAN hollow fiber membrane, to enhance the application performance of low molecular weight PAN membrane, and to adjust the porosity, pore size distribution, and hydrophilicity of the end product. The structurally-optimized membrane was chosen as a substrate to support Fe/Mn oxides and then used as a reactor to remove dyes from their solutions in the presence of H2O2. The results showed that the flux of methylene blue (MB) aqueous solution was 83.7 L/m2 h for the PAN homogeneous blend membrane, much higher than 29.1 L/m2 h of high molecular weight PAN membrane; MB removal efficiency was 97.3%, higher than 62.3% of low molecular weight PAN membrane, and it could be reused 25 times to remove dyes from their solutions without any loss in removal efficiency. The membrane was also found to have the application advantages of decreasing H2O2 dosage, reducing operation pressure, and raising MB removal efficiency compared with other membranes reported in the pieces of literature. Therefore, we were confident that the hollow fiber membrane fabricated by us would exhibit great application potential in the field of decontaminating dye wastewater.

In-situ formation of durable akaganeite (β-FeOOH) nanorods on sulfonate-modified poly(ethylene terephthalate) fabric for dual-functional wastewater treatment

Industrial oily wastewater with dye-pollution is a critical environmental issue for water purification. However, the fabrication of effective and stable materials for oil-water separation and simultaneous degradation of organic contaminants remains a critical challenge. Herein, we report a new process for in-situ formation of akaganeite (β-FeOOH) nanorods layer on the surface of poly(ethylene terephthalate) (PET) fabric via radiation-induced graft polymerization of glycidyl methacrylate, which is then sulfonated and mineralized. The resultant product is labeled as β-FeOOH@PET, which exhibits dual purification by demonstrating an effective oil-water separation and organic dyes photodegradation under the illumination of visible light. It provides stable performance even after 1000 wash cycles. The sulfonated layer acts as not only an electronic transport layer to prevent electron-hole recombination, but also as an anchored interface for immobilizing β-FeOOH nanorods on the sulfonated layer via strong covalent bonds. Overall, the superhydrophilicity and underwater superoleophobicity of β-FeOOH@PET fabric, along with its robustness with a flexible organic substrate and its dual purification function, provide a new insight toward oily wastewater remediation and water purification in large-scale applications.

Synergistic oxidation - filtration process analysis of catalytic CuFe2O4 - Tailored ceramic membrane filtration via peroxymonosulfate activation for humic acid treatment

This work synthesized catalytic CuFe₂O₄ tailored ceramic membrane (CuFeCM), and systematically investigated the intercorrelated oxidation - filtration mechanism of peroxymonosulfate (PMS)/CuFeCM catalytic filtration for treating humic acid (HA). PMS/CuFeCM filtration exhibited enhanced HA removal efficiency while reduced the irreversible fouling resistance as compared with the conventional CM filtration. Results from HA characterizations showed that PMS/CuFeCM catalytic filtration oxidized HA into conjugated structures of smaller molecular weight. The unsaturated bonds further caused the re-agglomeration of HA, hence enhancing the size exclusion of CuFeCM. Meanwhile, oxidized HA particles with changing physicochemical properties reduced the total attractive interaction energy between CuFeCM and HA, mainly attributed to the reduced acid-base interaction energy according to the Extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) analysis. The changing of HA properties and HA-CuFeCM physicochemical interactions rendered more re-agglomerated HA particles retained above membrane with less attachment, which induced decreasing irreversible fouling resistance and facilitated easier external fouling removal by hydraulic cleaning. Overall, the PMS/CuFeCM configuration demonstrated in this study could provide a new insight into the synergistic oxidation - filtration interaction mechanism of hybrid catalytic ceramic membrane filtration process.

Fabrication of hierarchical layer-by-layer membrane as the photocatalytic degradation of foulants and effective mitigation of membrane fouling for wastewater treatment

A polyvinylidene fluoride plate sheet membrane coated 3D TiO₂/poly (sodium styrenesulfonate) (PSS) photocatalyst layers were fabricated via dip-coating layer-by-layer (LbL) assembly. Cationic TiO₂ and anionic PSS were alternately stacked on the support membrane via electrostatic interactions. The obtained modified membrane with (TiO₂/PSS)₇ exhibited optimal versatility under ultraviolet light irradiation in both dead-end and membrane reactor, which showed superior Lanasol Blue 3R (LB) removal rate to membrane filtration and biodegradation. The modified membranes (MM) exhibited good performance in terms of photocatalytic activity of foulant degradation and mitigation of membrane fouling in a membrane reactor. The obtained MM with (TiO₂/PSS)₇ exhibited optimal versatility under ultraviolet light irradiation in both dead-end and membrane reactors and superior Lanasol Blue 3R removal rate in membrane filtration and biodegradation. The MM (TiO₂/PSS)₇ possessed excellent antifouling properties by using bovine serum albumin (BSA), as evidenced by the extended Derjaguin-Landau-Verwey-Overbeek theory. Additionally, the TiO₂/PSS membrane showed good self-cleaning ability, and the foulants on the membrane surface could be degraded using ultraviolet light irradiation.

Fenton cleaning strategy for ceramic membrane fouling in wastewater treatment

Membrane fouling is an obstacle impeding the wide applications of ceramic membranes and organics are responsible for most of the membrane fouling issues in wastewater treatment. In this study, Fenton cleaning strategy was firstly proposed to clean ceramic membrane fouling in wastewater treatment. Fe²⁺ efficiently catalyzed fouling cleaning with H₂O₂ (1.5%) to recover the filterability of ceramic membrane. The maximum ∆TMP recovery (over 99%) was achieved at an optimal Fe²⁺ dosage of 124 mg/L after 6 hr of immersion cleaning. The total residual membrane fouling resistance decreased gradually from this optimum value as the Fe²⁺ dosage increased above 124 mg/L. The residual hydraulically reversible fouling resistance accounted for most of the membrane fouling and was basically removed (≤3.0 × 10⁹ m^-1) when Fe²⁺ dosages higher than 124 mg/L were used. The foulants responsible for the formation of a residual hydraulically reversible fouling layer (DOC (dissolved organic carbon), proteins, polysaccharides, EEM (fluorescence excitation-emission matrix spectra), SS (suspended solids), and VSS (volatile suspended solids)) were gradually removed as the Fe²⁺ dosage increased. These residual organic foulants were degraded from biopolymers (10-200 kDa) to low molecular weight substances (0.1-1 kDa), and the particle size of these residual foulants decreased significantly as a result. The strong oxidation power of hydrogen peroxide/hydroxy radicals towards organic foulants was enhanced by Fe²⁺. Fe²⁺ played a significant role in the removal of hydraulically reversible fouling and irreversible fouling from the ceramic membrane. However, Fe²⁺ (≥124 mg/L) increased the likelihood of forming secondary iron-organics aggregates.

Nanofiltration Membranes with Metal Cation-Immobilized Aminophosphonate Networks for Efficient Heavy Metal Ion Removal and Organic Dye Degradation

Modifications to the surface of polymeric membranes to integrate supplemental properties like surface charge or catalytic activity are the cornerstone of the membrane process advancement to effectuate improvements in functionality and selectivity. Herein, a new approach is demonstrated to construct nanofiltration membranes with a metal-organic coordinated selective layer. Polyethylenimine (PEI) was integrated with phosphite linkages to form a characteristic aminophosphonate ester polymer based on the Kabachnik-Fields reaction, and a thin polymer layer was deposited on an ultrafiltration (UF) membrane to form the aminophosphonate networks surface-modified membranes. The aminophosphonate polymer interlayer facilitated the immobilization of metal cation moieties through the strong coordinative chemical bonding with the amino groups and phosphite moieties. Typically, the incorporated Fe³⁺ strengthened the membranes' electropositivity leading to excellent heavy metal ion removal (>98%) and efficient organic dye separation (>99.8%). Meanwhile, the strategy also enabled the embedment of a photocatalytic layer comprising nanoneedle-like α-FeOOH that endowed the membrane with high photo-Fenton activity for organic dye mineralization. Subsequently, the α-FeOOH-embedded membrane afforded the photocatalytic self-cleaning potentiality for organic fouling mitigation. This contribution underscores the prospect of advancing the integration of metal-specific functionalities and the membrane process for advanced membrane technologies in water treatment.