Fabrication of hybrid ultrafiltration membranes with improved water separation properties by incorporating environmentally friendly taurine modified hydroxyapatite nanotubes

Modification of polyvinylidene fluoride membrane with ciprofloxacin to improve the bacteriostatic performance

The common polyvinylidene fluoride (PVDF) membrane itself is susceptible to membrane fouling, especially biofouling, which is a serious threat. In this study, PVDF membrane was modified with ciprofloxacin (CIP) through co-blending to investigate the filtration properties, bacterial inhibition and fouling resistance. Modified membranes were prepared by adding 0.3 g (MC0.3), 0.6 g (MC0.6), 0.9 g (MC0.9) and 1.2 g (MC1.2) CIP per 100 g casting solution. Among these modified membranes, MC0.6 showed the best filtration performances, with the pure water flux stabilized at about 416.67 L/(m2·h) and bovine serum albumin (BSA) rejection of 92.0% at a trans-membrane pressure of 0.1 MPa. The pore size was reduced, the average roughness was reduced to 29.4 nm, the contact angle was lowered to 68.9°, and the hydrophilicity was greatly improved. The width of the inhibition circle produced by MC0.6 was 0.35-0.45 mm, and the modified membrane showed good inhibition of non-specific bacteria and algal removal during urban river water filtration. The rejection of BSA was increased by 16.32% compared to the base membrane and the adsorption rate for BSA was reduced by 68.45%. In addition, the removal of conventional pollutants in urban river water by the modified membranes for was also improved. Compared with that of the base membrane, the removal of TN, NH3-N, TP and COD by MC0.6 was increased by 10.58%, 12.45%, 15.44% and 13.53%. The results showed that CIP co-blending modified PVDF membrane could effectively improve membrane performances and has good value for water treatment.

Development of a new biomaterial based on cashew tree gum (Anarcadium occidentale L.) enriched with hydroxyapatite and evaluation of cytotoxicity in adipose-derived stem cell cultures

Cashew tree gum is a polysaccharide material highly available in the Northeast region of Brazil. It has been explored for biocompatibility with human tissues. This research aimed to describe the synthesis and characterization of cashew gum/hydroxyapatite scaffold and evaluate the possible cytotoxicity in murine adipo-derived stem cells (ADSCs) cultures. ADSCs of the subcutaneous fat tissue of Wistar rats were collected, isolated, expanded, differentiated into three strains, and characterized immunophenotypically. The scaffolds were synthesized through chemical precipitation, lyophilized and characterized through scanning electron microscopy (SEM), infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermal analysis (TG and DTG), and mechanical testing. The scaffold presented a crystalline structure and pores with an average diameter of 94.45 ± 50.57 μm. By mechanical tests, the compressive force and modulus of elasticity were like the cancellous bone. The isolated adipose-derived stem cells (ADSCs) presented fibroblast morphology, adhesion capacity to plastic, differentiation in osteogenic, adipogenic and chondrogenic lineages, positive expression for the CD105 and CD90 markers and negative expression for the CD45 and CD14 markers. The MTT test showed increased cell viability, and the biomaterial showed a high level of hemocompatibility (<5 %). This study allowed the development of a new scaffold for future surgical applicability in tissue regeneration.

Oxidized carbide-derived carbon as a novel filler for improved antifouling characteristics and permeate flux of hybrid polyethersulfone ultrafiltration membranes

Polyethersulfone (PES) is a widely used polymer for ultrafiltration (UF) membrane fabrication. In the current study, carbide-derived carbon (CDC) oxidized by acid treatment was utilized as a filler to fabricate a novel PES composites UF membranes. The successful oxidation of CDC was validated from presence of oxygen containing functional groups and improved oxygen content, from 5.08 at.% for CDC to 26.22 at.% for oxidized CDC (OCDC). The OCDC PES UF membranes were prepared at different loadings of OCDC between 0.5 and 3.0 wt%. The membrane porosity, pore size and surface free energy found to be improved while a noticeable reduction in water contact angle was observed with OCDC loading implying the improved hydrophilicity of PES membranes. Consequently, the pure water flux found to improve from 151.6 to 569.6 (L/(m². h)) for the 3.0 wt% modified OCDC membrane (M-3) which is 3.8 folds of the bare PES membrane. The antifouling characteristics were evaluated by humic acid (HA) filtration. The results revealed a significant enhancement in HA rejection with OCDC loading, the highest rejection was 96.8% for M-3 membrane. Additionally, the adsorption capacity of OCDC modified membranes found to decrease with OCDC loading indicating improved rejection of HA from the membrane surface. Moreover, M-3 demonstrated the maximum flux recovery ratio (FRR) of 92.3%. Reusability of the fabricated membranes was evaluated by deionized water/humic acid cycling filtration. The FRR was higher than 86.7% over three cycles of pure water/HA filtration for 140 min, indicated the excellent stability and reusability of the membranes. Overall, the OCDC was an effective filler for enhancing the PES UF membranes antifouling and permeability properties.

Recent Advances on the Fabrication of Antifouling Phase-Inversion Membranes by Physical Blending Modification Method

Membrane technology is an essential tool for water treatment and biomedical applications. Despite their extensive use in these fields, polymeric-based membranes still face several challenges, including instability, low mechanical strength, and propensity to fouling. The latter point has attracted the attention of numerous teams worldwide developing antifouling materials for membranes and interfaces. A convenient method to prepare antifouling membranes is via physical blending (or simply blending), which is a one-step method that consists of mixing the main matrix polymer and the antifouling material prior to casting and film formation by a phase inversion process. This review focuses on the recent development (past 10 years) of antifouling membranes via this method and uses different phase-inversion processes including liquid-induced phase separation, vapor induced phase separation, and thermally induced phase separation. Antifouling materials used in these recent studies including polymers, metals, ceramics, and carbon-based and porous nanomaterials are also surveyed. Furthermore, the assessment of antifouling properties and performances are extensively summarized. Finally, we conclude this review with a list of technical and scientific challenges that still need to be overcome to improve the functional properties and widen the range of applications of antifouling membranes prepared by blending modification.

Synergistic Effect of Chitosan and Metal Oxide Additives on Improving the Organic and Biofouling Resistance of Polyethersulfone Ultrafiltration Membranes

The combination of chitosan and metal oxides was utilized as an addition to improve the fouling resistance of polyethersulfone (PES) ultrafiltration membranes. Pure water flux, membrane hydrophilicity by the contact angle, scanning electron micrographs, and Fourier-transform infrared spectra were used to characterize the membranes. With the addition of metal oxides, the modified membrane's water flux increased. The PES membrane with 0.25% wt chitosan and 2.0% wt AgNO₃ had the highest flux and antibacterial activity among the membranes tested. Because of its potential to improve membrane hydrophilicity, the water flux increased with the addition of chitosan and AgNO₃. Because of the improved hydrophilicity, the contact angle reduced as chitosan and Ag loading was increased. The PES-chitosan-Ag₂O (from AgNO₃ 2.0% wt) membrane had high antibacterial activity against Escherichia coli and Staphylococcus aureus, whereas the PES-2.0% wt Ag membrane did not show the same result. Finally, the addition of chitosan in the PES-Ag membrane increased the membrane's antibacterial activity substantially.

Enhanced water flux and bacterial resistance in cellulose acetate membranes with quaternary ammoniumpropylated polysilsesquioxane

An enhanced water flux and anti-fouling nanocomposite ultrafiltration membrane based on quaternary ammoniumpropylated polysilsesquioxane (QAPS)/cellulose acetate (QAPS@CA) was fabricated by in situ sol-gel processing via phase inversion followed by quaternization with methyl iodide (CH₃I). Membrane characterizations were performed based on the contact angle, FTIR, SEM, and TGA properties. Membrane separation performance was assessed in terms of pure water flux, rejection, and fouling resistance. The 7%QAPS@CA nanocomposite membrane showed an increased wettability (46.6° water contact angle), water uptake (113%) and a high pure water permeability of ∼370 L m^-2 h^-1 bar^-1. Furthermore, the 7%QAPS@CA nanocomposite membrane exhibited excellent bactericidal properties (∼97.5% growth inhibition) against Escherichia coli (E. coli) compared to the bare CA membrane (0% growth inhibition). The 7%QAPS@CA nanocomposite membrane can be recommended for water treatment and biomedical applications.

Bioactive Surface Modifications through Thermally Sprayed Hydroxyapatite Composite Coatings: A Review over Selective Reinforcements

Hydroxyapatite (HA) has been an excellent replacement for the natural bone in orthopedic applications, owing to its close resemblance; however, it is brittle and has low strength. Surface modification techniques...

Fabrication of photo-Fenton self-cleaning PVDF composite membrane for highly efficient oil-in-water emulsion separation

The anti-fouling performance of membranes is an important performance in the separation of oil/water.

Enhanced water permeability and fouling resistance properties of ultrafiltration membranes incorporated with hydroxyapatite decorated orange-peel-derived activated carbon nanocomposites

Hydroxyapatite-decorated activated carbon (HAp/AC) nanocomposite was synthesized and utilized as a nanofiller to fabricate a novel type of polyethersulfone (PES) nanocomposite ultrafiltration (UF) membranes. Activated carbon (AC) derived from orange peel was synthesized by low-temperature pyrolysis at 400 °C. A hydroxyapatite/AC (HAp/AC) nanocomposite was developed by a simple one-pot hydrothermal synthesis method. The UF membrane was fabricated by intercalating HAp/AC fillers into PES casting solution by the non-solvent induced phase separation (NIPS) process. The prepared membranes exhibited a lower water contact angle than the pristine PES membrane. The hybrid membrane with 4 wt% HAp/AC nanocomposite displayed 4.6 times higher pure water flux (~660 L/m² h) than that of the pristine membrane (143 L/m² h). In static adsorption experiments, it was found that the amount of humic acid (HA) and bovine serum albumin (BSA) adsorbed by the HAp/AC-PES hybrid membrane was much lower than that of the original membrane due to the electrostatic repulsive forces between them and the surface of the membrane. Irreversible fouling was reduced from 33 to 6 % for HA and from 46 to 8 % for BSA after HAp/AC was incorporated into the PES matrix. After 7 cycles of water-BSA-water, the HAp/AC-PES hybrid membrane maintained a high pure water flux of 540 L/m² h with an excellent flux recovery ratio (FRR), demonstrating the long-term stability of the membranes. The developed UF membranes outperformed the original PES membranes in terms of permeability, selectivity, and antifouling.

Design of a novel poly(aryl ether nitrile)-based composite ultrafiltration membrane with improved permeability and antifouling performance using zwitterionic modified nano-silica

Zwitterionic nano-silica (SiO₂ NPs) obtained by lysine surface modification was used as a hydrophilic inorganic filler for preparing a poly(aryl ether nitrile) (PEN) nanocomposite membrane via an immersion precipitation phase inversion method. The effects of zwitterionic SiO₂ NPs addition on the morphology, separation and antifouling performance of the synthesized membranes were investigated. Zwitterionic surface modification effectively avoided the agglomeration of SiO₂ NPs. The PEN/zwitterionic SiO₂ NPs composite membranes exhibited improved porosity, equilibrium water content, hydrophilicity and permeability due to the introduction of hydrophilic SiO₂ NPs in the casting solution, and the optimal pure water flux was up to 507.2 L m⁻² h⁻¹, while the BSA rejection ratio was maintained at 97.4%. A static adsorption capacity of 72.9 μg cm⁻² and the FRR up to 85.3% in the dynamic antifouling experiment proved that the introduction of zwitterionic SiO₂ NPs inhibited irreversible fouling and enhanced the antifouling ability of the PEN membrane.

Zwitterionic nano-silica (SiO₂ NPs) obtained by lysine surface modification was used as a hydrophilic inorganic filler for preparing a poly(aryl ether nitrile) (PEN) nanocomposite membrane via an immersion precipitation phase inversion method.

Improved permeability and antifouling performance of polyethersulfone ultrafiltration membranes tailored by hydroxyapatite/boron nitride nanocomposites

To extend the use of polyethersulfone (PES) ultrafiltration membranes in water process engineering, the membrane's wettability and anti-fouling properties should be further improved. In this context, hydroxyapatite/boron nitride (HAp/BN) nanocomposites have been prepared and intercalated into PES membranes using a non-solvent-induced phase separation process. High-quality 2D transparent boron nitride nanosheets (BN NSs) were prepared using an environmentally friendly and green-template assisted synthesis method in which 1D hexagonal hydroxyapatite nanosheets (HAp NRs) were uniformly distributed and hydrothermally immobilized at 180 °C. SEM, XRD, and Raman spectroscopy techniques were used to characterize the HAp/BN nanocomposites. PES membranes intercalated with various nanocomposite amounts (0-4 wt %) were also characterized by permeability, porosity, and contact angle measurements. Additional pathways for water molecule transport were promoted by the high surface area of the BN NSs, resulting in high permeability. Membrane wettability and antifouling properties were also improved by the inclusion of negative charge groups (OH^- and PO₄^3-) on HAp. Hybrid membranes containing 4 wt% HAp/BN showed the best overall performance with ∼97% increase in water flux, 90% rejection of bovine serum albumin (BSA), high water flux recovery ratio, low irreversible fouling, and high reversible fouling pattern. The intercalation of HAp/BN with the PES matrix therefore opens up a new direction to enhance the PES UF membranes' hydrophilicity, water flux, and antifouling capacity.

Combined strategy of blending and surface modification as an effective route to prepare antifouling ultrafiltration membranes

Ultrafiltration (UF) membranes blended with hydrophilic nanomaterials usually exhibit preferable overall performance including the membrane permeability and antifouling capability. However, the improvement in antifouling performance may be not outstanding due to the small amount of nanomaterial distributed near the membrane surface and the limited improvement in membrane hydrophilicity. Notably, excess addition of nanomaterials may lead to the decline in membrane permeability. In order to solve the above problem, we integrated the strategy of blending and surface modification to construct novel hybrid UF membranes. Novel nanohybrid was prepared via tannic acid (TA) coating on hydroxyapatite nanotubes (HANTs) and the subsequent grafting of zwitterionic polyethylenimine (ZPEI). The prepared nanohybrid (HANTs@TA-ZPEI) was incorporated with the polysulfone containing tertiary amine groups to fabricate hybrid membranes via the solution blending and the subsequent immersion-precipitation phase inversion process. Then the matrix was modified with zwitterions via the reaction of tertiary amine group with 1, 3-propane sultone. UF tests were conducted using the bovine serum albumin (BSA) and humic acid (HA) as the representative foulants. Results showed that both the permeability and the antifouling performance of the membranes achieved favorable promotion. Thereinto, the water flux of M-B0.4-Z membrane (pre blended with 0.4 wt% HANTs@TA-ZPEI in the casting solution and post-surface modified) exhibited 2.6 times that of the pristine membrane and the flux recovery ratio (FRR) for BSA and HA attained 93.4% and 96.1%, respectively. By the combination of blending and surface modification, both the membrane permeability and fouling resistant properties could attain remarkable promotion, which exerted the advantages of two methods and made up the deficiency of single blending method.

The hierarchical flower-like MoS2 nanosheets incorporated into PES mixed matrix membranes for enhanced separation performance

Membrane fouling is an issue of concern due to the hydrophobic properties of polyethersulfone (PES) membrane when applied in water treatment. In this work, a facile hydrothermal method was utilized to synthesize hierarchical flower-like structured molybdenum disulfide nanosheets (HF-MoS2 NSs) that then incorporated into PES membranes as composite membranes. We characterized their permeability, the separation performance, the antifouling performance, and the antibacterial activity systematically. Results showed that composite membranes exhibited a better pure water flux (286 LMH/bar) at the HF-MoS₂ NSs content of 0.4 wt%, which was 1.8 times higher than the control membrane. Also, composite PES membranes achieved 98.2% and 96.9% rejection of BSA and HA in comparison with the control PES membrane (87.3%, and 84.5%, respectively). Compare to the control PES membrane, the flux recovery ratio of the composite membrane increased from 69% to 88% for BSA fouling and increased from 84% to 93% for HA fouling. The retention rate for the organic dyes also improved slightly after HF-MoS2 NSs incorporation into the membrane. Additionally, the composite membranes exhibited a relatively high antibacterial activity against E. coli and B. subtilis with antibacterial rates of 67.8% and 82.5%, respectively. In conclusion, HF-MoS2 NSs incorporated composite membranes were shown to have outstanding filtration performance and could be a promising candidate for practical application in water filtration.

Enhanced permeability, mechanical and antibacterial properties of cellulose acetate ultrafiltration membranes incorporated with lignocellulose nanofibrils

Cellulose acetate (CA) ultrafiltration membranes are attracting more attention in wastewater purification due to its biodegradability and eco-friendly. The application of CA membranes, however, is limited by high susceptibility to bacterial corrosion and lack of mechanical tolerance that results in loss of life. To solve the above problems, we first fabricated the CA-based composite membranes incorporated with bamboo-based lignocellulose nanofibrils (LCNFs) by a strategy of phase inversion. LCNFs was prepared by using a combined method of one-step chemical pretreatment and acid hydrolysis coupled with high-pressure homogenization. The as-prepared CA/LCNFs composite membranes with 4 wt% lignin in the LCNFs exhibited high tensile strength of 7.08 MPa and strain-at-break of 12.21%, and high filtration permeability of 188.23 L·m^-2·h^-1 as ultrafiltration membranes for wastewater treatment, which could obviously inhibit the growth of Escherichia coli.

Development of Composite Scaffolds Based on Cerium Doped-Hydroxyapatite and Natural Gums-Biological and Mechanical Properties

Hydroxyapatite (HAp) is a ceramic material composing the inorganic portion of bones. Ionic substitutions enhance characteristics of HAp, for example, calcium ions (Ca²⁺) by cerium ions (Ce³⁺). The use of HAp is potentialized through biopolymers, cashew gum (CG), and gellan gum (GG), since CG/GG is structuring agents in the modeling of structured biocomposites, scaffolds. Ce-HApCG biocomposite was synthesized using a chemical precipitation method. The obtained material was frozen (–20 °C for 24 h), and then vacuum dried for 24 h. The Ce-HApCG was characterized by X-Ray diffractograms (XRD), X-ray photoemission spectra (XPS), Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), and energy dispersive spectroscopy (EDS). XRD and FTIR showed that Ce-HApCG was successfully synthesized. XRD showed characteristic peaks at 2θ = 25.87 and 32.05, corresponding to the crystalline planes (0 0 2) and (2 1 1), respectively, while phosphate bands were present at 1050 cm⁻¹ and 1098 cm⁻¹, indicating the success of composite synthesis. FESEM showed pores and incorporated nanostructured granules of Ce-HApCG. The mechanical test identified that Ce-HApCG has a compressive strength similar to the cancellous bone’s strength and some allografts used in surgical procedures. In vitro tests (MTT assay and hemolysis) showed that scaffold was non-toxic and exhibited low hemolytic activity. Thus, the Ce-HApCG has potential for application in bone tissue engineering.

Fabricating PES/SPSF membrane via reverse thermally induced phase separation (RTIPS) process to enhance permeability and hydrophilicity

A new method was presented to prepare hydrophilic PES/SPSF flat-sheet membrane by a reverse thermally induced phase separation (RTIPS) method to enhance permeability and hydrophilicity. SPSF was self-made and was blended to improve the hydrophilicity of PES flat-sheet membrane. The performance of PES/SPSF flat-sheet membrane, which varied with SPSF content and coagulation water bath temperature, was investigated by SEM, FTIR, AFM, pure water flux, BSA rejection rate, water contact angle and long-term testing. FTIR results proved the successful blending of SPSF with PES membrane, SEM images showed that dense skin surface and finger-like structure emerged in the membrane fabricated by NIPS method, while a porous top surface and sponge-like structure emerged in the membrane fabricated by RTIPS. The pure water flux and BSA rejection rate of the membrane for RTIPS were both higher than those for NIPS. AFM images revealed that surface roughness increased with the addition of SPSF. The water contact angle decreased with the increase of SPSF, which illustrated better hydrophilicity with the addition of SPSF. The flat-sheet PES membrane prepared with 2 wt% SPSF by RTIPS method exhibited decent properties, reaching maximum pure water flux (966 L m⁻² h⁻¹) and at the same time the BSA rejection rate was 79.2%. The long-term test proved that the anti-fouling performance of PES/SPSF membrane was better than that of PES membrane.

A new method is presented to prepare hydrophilic PES/SPSF flat-sheet membrane by a reverse thermally induced phase separation (RTIPS) method to enhance permeability and hydrophilicity.