Incorporation of a novel Ag–Cu@ZIF-8@GO nanocomposite into polyethersulfone membrane for fouling and bacterial resistance

Task-specific polymeric membranes to achieve high gas-liquid mass transfer

In the current study, Polyimide (P84)-based polymeric membranes were fabricated and used as spargers in the bubble column reactor (BCR) to get a high gas-liquid mass transfer (GL-MT) rate of oxygen in water. Different polymeric membranes were fabricated by incorporating polyvinyl pyrrolidone (PVP) as a porogen and a Zeolitic Imidazolate Framework (ZIF-8) to induce high porosity and hydrophobicity in the membranes. The GL-MT efficiency of membranes was evaluated by measuring the overall volumetric mass transfer coefficient (k_La) of oxygen in air. The k_La of O₂ (in air) was measured by supplying the gas through a fixed membrane surface area of 11.94 cm² at a fixed gas flow rate of 3L/min under atmospheric pressure. The results revealed that adding porogen and ZIF-8 increased the porosity of the membranes compared to the pure polymeric membranes. In comparison, the ZIF-8 (3 wt%) based membrane showed the highest porosity (80%), hydrophobicity (95° contact angle) and k_La of oxygen in air (241.2 h^-1) with 78% saturation in only 60 s. ZIF-8 based membranes showed the potential to increase the amount of dissolved oxygen in BCR by reducing the bubble size, increasing the number of bubbles, and improving the hydrophobicity. The study showed that ZIF-8 based membrane diffusers are expected to produce high GL-MT in microbial syngas fermentation. To the best of our knowledge, this is the first study on the fabrication and application of polymeric membranes for GL-MT applications. Further research should be conducted under real fermentation conditions to assess the practicality of the system to support substrate utilization, microbial growth, and product formation.

Enhanced Separation Performance of Polyamide Thin-Film Nanocomposite Membranes with Interlayer by Constructed Two-Dimensional Nanomaterials: A Critical Review

Thin-film composite (TFC) polyamide (PA) membrane has been widely applied in nanofiltration, reverse osmosis, and forward osmosis, including a PA rejection layer by interfacial polymerization on a porous support layer. However, the separation performance of TFC membrane is constrained by the trade-off relationship between permeability and selectivity. Although thin-film nanocomposite (TFN) membrane can enhance the permeability, due to the existence of functionalized nanoparticles in the PA rejection layer, the introduction of nanoparticles leads to the problems of the poor interface compatibility and the nanoparticles agglomeration. These issues often lead to the defect of PA rejection layers and reduction in selectivity. In this review, we summarize a new class of structures of TFN membranes with functionalized interlayers (TFNi), which promises to overcome the problems associated with TFN membranes. Recently, functionalized two-dimensional (2D) nanomaterials have received more attention in the assembly materials of membranes. The reported TFNi membranes with 2D interlayers exhibit the remarkable enhancement on the permeability, due to the shorter transport path by the "gutter mechanism" of 2D interlayers. Meanwhile, the functionalized 2D interlayers can affect the diffusion of two-phase monomers during the interfacial polymerization, resulting in the defect-free and highly crosslinked PA rejection layer. Thus, the 2D interlayers enabled TFNi membranes to potentially overcome the longstanding trade-off between membrane permeability and selectivity. This paper provides a critical review on the emerging 2D nanomaterials as the functionalized interlayers of TFNi membranes. The characteristics, function, modification, and advantages of these 2D interlayers are summarized. Several perspectives are provided in terms of the critical challenges for 2D interlayers, managing the trade-off between permeability, selectivity, and cost. The future research directions of TFNi membranes with 2D interlayers are proposed.

Purifying water with silver nanoparticles (AgNPs)-incorporated membranes: Recent advancements and critical challenges

In the face of the growing global water crisis, membrane technology is a promising means of purifying water and wastewater. Silver nanoparticles (AgNPs) have been widely used to improve membrane performance, for antibiofouling, and to aid in photocatalytic degradation, thermal response, and electro-conductivity. However, several critical issues such as short antimicrobial periods, trade-off effects and silver inactivation seriously restrict the engineering application of AgNPs-incorporated membranes. In addition, there is controversy around the use of AgNPs given the toxic preparation process and environmental/biological risks. Hence, it is of great significance to summarize and analyze the recent developments and critical challenges in the use of AgNPs-incorporated membranes in water and wastewater treatment, and to propose potential solutions. We reviewed the different properties and functions of AgNPs and their corresponding applications in AgNPs-incorporated membranes. Recently, multifunctional, novel AgNP-incorporated membranes combined with other functional materials have been developed with high-performance. We further clarified the synergistic mechanisms between AgNPs and these novel nanomaterials and/or polymers, and elucidated their functions and roles in membrane separation. Finally, the critical challenges of AgNPs-incorporated membranes and the proposed solutions were outlined: i) Prolonging the antimicrobial cycle through long-term and controlled AgNPs release; ii) Overcoming the trade-off effect and organic fouling of the AgNPs-incorporated membranes; iii) Preparation of sustainable AgNPs-incorporated membranes; iv) Addressing biotoxicity induced by AgNPs; and v) Deactivation of AgNPs-incorporated membrane. Overall, this review provides a comprehensive discussion of the advancements and challenges of AgNPs-incorporated membranes and guides the development of more robust, multi-functional and sustainable AgNPs-incorporated membranes.

Preparation of polyvinylidene fluoride composite ultrafiltration membrane for micro-polluted surface water treatment

Blending modification of graphene oxide (GO) and deposition of silver carbonate (Ag₂CO₃) on the membrane surface by suction filtration was used to prepare polyvinylidene fluoride (PVDF) composite ultrafiltration (UF) membranes (denoted as PGA membranes). The effect of this strategy on the morphology and performance of the pure PVDF membrane was investigated. Owing to an increased hydrophilicity and the formation of a more open pore, the pollution resistance and permeability of the PGA membrane were improved. The pure water flux of the PGA-3 membrane (254 LMH) was increased to more than 2-fold compared to that of the neat PVDF membrane (126 LMH). In addition, the results of antifouling experiments showed that the flux recovery rate, flux decay rate, and antibacterial performance of the PGA-3 membrane was superior to those of the other membranes synthesized in this study. Finally, after conducting multi-cycle filtration experiments with lake water, the flux and recovery rate of the PGA-3 membrane was observed to be the highest, and the water quality of the lake water filtered by the PGA-3 membrane was the best. Thus, the above results indicate that this membrane modification strategy is extraordinarily effective in improving the antifouling properties and permeability of the PVDF UF membranes in practical applications.