Ultrasound-assisted dispersive liquid-liquid microextraction for determination of enrofloxacin in surface waters

Detection methods for antibiotics in wastewater: a review

Antibiotics are widely used as fungicides because of their antibacterial and bactericidal effects. However, it is necessary to control their dosage. If the amount of antbiotics is too much, it cannot be completely metabolized and absorbed, will pollute the environment, and have a great impact on human health. Many antibiotics usually left in factory or aquaculture wastewater pollute the environment, so it is vital to detect the content of antibiotics in wastewater. This article summarizes several common methods of antibiotic detection and pretreatment steps. The detection methods of antibiotics in wastewater mainly include immunoassay, instrumental analysis method, and sensor. Studies have shown that immunoassay can detect deficient concentrations of antibiotics, but it is affected by external factors leading to errors. The detection speed of the instrumental analysis method is fast, but the repeatability is poor, the price is high, and the operation is complicated. The sensor is a method that is currently increasingly studied, including electrochemical sensors, optical sensors, biosensors, photoelectrochemical sensors, and surface plasmon resonance sensors. It has the advantages of fast detection speed, high accuracy, and strong sensitivity. However, the reproducibility and stability of the sensor are poor. At present, there is no method that can comprehensively integrate the advantages. This paper aims to review the enrichment and detection methods of antibiotics in wastewater from 2020 to the present. It also aims to provide some ideas for future research directions in this field.

On-site extraction using a 3D printed device coated with Zn/Co-ZIF-derived carbon followed by an on-line SIA-HPLC-FL system for fluoroquinolones determination in wastewater

A 3D printed device covered with Zn/Co-ZIF-derived carbon allows the on-site extraction of fluoroquinolones (FQs) from wastewater, avoiding the sample transportation to the laboratory, and the subsequent elution, separation and determination using an on-line flow system based on sequential injection analysis (SIA) coupled to HPLC-FL. Several parameters that affect the extraction efficiency and desorption were optimized including the sorption phase immobilization technique on the 3D device, extraction time, pH effect, sample volume as well as the type of eluent, eluent volume, and flow rate. Under optimum conditions, detection limits of 3-9 ng L-1 were achieved for norfloxacin, ciprofloxacin, danofloxacin, enrofloxacin and difloxacin. The precision expressed as relative standard deviation (%RSD, n = 3), showed intraday and interday ranges of 1.5-5.3% and 2.8-5.7%, respectively, demonstrating a good precision of the proposed methodology. To assess matrix effects and accuracy of the proposed method in real samples, recovery studies were performed without and with FQs spiked at different concentrations (0.5-10 μg L-1) to wastewater samples, showing good recoveries in the range of 91-104%. The results allow to confirm the applicability of MOF-derived carbons as adsorbents for on-site extraction, and the satisfactory separation and quantification of FQs by a SIA-HPLC-FL on-line system after their desorption with small eluent volumes.

TPN-COF@Fe-MIL-100 composite used as an electrochemical aptasensor for detection of trace tetracycline residues

In this work, a metal-organic framework@covalent organic framework composite (TPN-COF@Fe-MIL-100) was prepared and used as a sensing material to construct an aptasensor for trace detection of tetracycline (TET). The TPN-COF@Fe-MIL-100 integrates a large surface area, porous structure, excellent electrochemical activity, rich chemical functionality, and strong bioaffinity for aptamers, providing abundant active sites to effectively anchor aptamer strands. As a result, the TPN-COF@Fe-MIL-100-based aptasensor shows high sensitivity for detecting TET via specific recognition between aptamer and TET to form G-quadruplex. An ultralow detection limit of 1.227 fg mL-1 is deduced from the electrochemical impedance spectroscopy within a wide linear range of 0.01-10000 pg mL-1 for TET. The TPN-COF@Fe-MIL-100-based aptasensor also exhibits good selectivity, reproducibility, stability, regenerability, and applicability for a real milk sample. Therefore, the TPN-COF@Fe-MIL-100-based aptasensor will be promising for detecting trace harmful antibiotics residues for food safety.

How to apply terpenoid-based deep eutectic solvents for removal of antibiotics and dyes from water: Theoretical prediction, experimental validation and quantum chemical evaluation

This study proposed a theoretical prediction method and mechanism investigation for the extraction of antibiotics and dyes from aqueous media using terpenoid-based deep eutectic solvents (DESs). Firstly, Conductor-like Screening Model for Real Solvents (COSMO-RS) approach was applied to predict selectivity, capacity and performance index in the extraction of 15 target compounds including antibiotics (tetracyclines, sulfonamides, quinolones, β-lactams) and dyes by 26 terpenoid-based DESs, and thymol-benzyl alcohol shows promising theoretical selectivity and extraction efficiency for the target compounds. Moreover, the structures of both hydrogen bond acceptors (HBA) and hydrogen bond donors (HBD) have an impact on the predicted extraction performance, which can be improved by tailoring those candidates with higher polarity, smaller molecular volume, shorter alkyl chain length and the presence of aromatic ring structures, etc. According to the predicted molecular interactions revealed by σ-profile and σ-potential, the DESs with HBD ability can promote the separation process. Furthermore, reliability of proposed prediction method was confirmed by experimental verification, indicating that the trends of theoretical extraction performance index were similar with the experimental results by using actual samples. At last, the extraction mechanism was evaluated by quantum chemical calculations based on visual presentations, thermodynamic calculations and topological properties; and the target compounds showed favorable energies of solvation to transfer from aqueous phase to DESs phase. The proposed method has been proved with potential to provide the efficient strategies and guidance for more applications (e.g., microextraction, solid phase extraction, adsorption) with similar molecular interactions of green solvents in environmental research.

Overview of Different Modes and Applications of Liquid Phase-Based Microextraction Techniques

Liquid phase-based microextraction techniques (LPµETs) have attracted great attention from the scientific community since their invention and implementation mainly due to their high efficiency, low solvent and sample amount, enhanced selectivity and precision, and good reproducibility for a wide range of analytes. This review explores the different possibilities and applications of LPμETs including dispersive liquid–liquid microextraction (DLLME) and single-drop microextraction (SDME), highlighting its two main approaches, direct immersion-SDME and headspace-SDME, hollow-fiber liquid-phase microextraction (HF-LPME) in its two- and three-phase device modes using the donor–acceptor interactions, and electro membrane extraction (EME). Currently, these LPμETs are used in very different areas of interest, from the environment to food and beverages, pharmaceutical, clinical, and forensic analysis. Several important potential applications of each technique will be reported, highlighting its advantages and drawbacks. Moreover, the use of alternative and efficient “green” extraction solvents including nanostructured supramolecular solvents (SUPRASs, deep eutectic solvents (DES), and ionic liquids (ILs)) will be discussed.

Lab-In-Syringe automation of deep eutectic solvent-based direct immersion single drop microextraction coupled online to high-performance liquid chromatography for the determination of fluoroquinolones

Lab-In-Syringe direct immersion single drop microextraction is proposed as an automated sample pretreatment methodology and coupled online to HPLC with fluorescence detection for the determination of fluoroquinolones in environmental waters. For the first time, a drop of a natural deep eutectic solvent (NADES), synthesized from hexanoic acid and thymol, has been used as an extractant in automated single-drop microextraction. The extraction procedure was carried out within the 5 mL void of an automatic syringe pump. A 9-position head valve served the aspiration of all required solutions, air, waste disposal, and hyphenation with the HPLC instrument. Sample mixing during extraction was done by a magnetic stirring bar placed inside the syringe. Only 60 μL of NADES were required omitting toxic classical solvents and improving the greenness of the proposed methodology. By direct injection, linear working ranges between 0.1 and 5 μg L^-1 were achieved for all fluoroquinolones. The limit of quantification values and enrichment factors ranged from 20 ng L^-1 to 30 ng L^-1 and 35 to 45, respectively. Accuracies obtained from the analysis of spiked surface water and wastewater treatment plant effluent analysis at two concentration levels (0.5 and 4 μg L^-1) ranged from 84.6% to 119.7%, with RSD values typically <3%.

Strategies of dispersive liquid-liquid microextraction for coastal zone environmental pollutant determination

Coastal zone means the interface of land and sea, and therefore, environmental pollutants steaming from land-based activities (like manufactories) and sea-based activities (like shipping) are all existing in coastal zone. These pollutants usually have characteristics of low residues, complicated matrices, easy accumulation and so on, causing difficulty to detect coastal pollutants quickly and sensitively. It is imperative to perform effective sample preparation prior to instrumental analysis. Dispersive liquid-liquid microextraction (DLLME) has attracted significant research interest for sample preparation, owing to its high enrichment ability, low reagent/sample consumption, and wide analyte/matrix applicability, as well as robustness, simplicity, rapidity and inexpensiveness. Herein, we comprehensively review the recent advancements of DLLME technology and its analytical parameters including enrichment principles, extraction modes, and practical application; the emphasis is on novel mode-construction and representative coastal-environmental pollutants extraction. Construction strategies are highlighted by classifying DLLME into five major modes, according to extractant's types, including normal ones, low density solvents, ionic liquids, deep eutectic solvents and others. The coupling of DLLME with other extraction techniques like solid-phase extraction is also briefly introduced. The strengths and weaknesses of each strategy and its rationality are also elaborated. In addition, some typical applications of the different DLLME modes for the determination of organic compounds and heavy metals in coastal water, sediment, soil, and biota are summarized. The increasingly concerned green aspects and instrumentation of DLLME are presented, and finally, the challenges and perspectives of the DLLME for environmental analysis are proposed.

Synthesis of molecularly imprinted polymers for extraction of fluoroquinolones in environmental, food and biological samples

In recent years, fluoroquinolones have been found present in important water resources and food sources which compromises the food quality and availability, thereby, causing risks to the consumer. Despite the recent advancement in the development of analytical instrumentation for routine monitoring of fluoroquinolones in water, food, and biological samples, sample pre-treatment is still a major bottleneck of the analytical methods. Therefore, fast, selective, sensitive, and cost-effective sample preparation methods prior to instrumental analysis for fluoroquinolones residues in environmental, food and biological samples are increasingly important. Solid-phase extraction using different adsorbents is one of the most widely used pre-concentration/clean-up techniques for analysis of fluoroquinolones. Molecularly imprinted polymers (MIPs) serve as excellent effective adsorbent materials for selective extraction, separation, clean-up and preconcentration of various pollutants in different complex matrices. Therefore, synthesis of MIPs remains crucial for their applications in sample preparation as this offers much-needed selectivity in the extraction of compounds in complex samples. In this study, the progress made in the synthesis of MIPs for fluoroquinolones and their applications in water, food and biological samples were reviewed. The present review discusses the selection of all the elements of molecular imprinting for fluoroquinolones, polymerization processes and molecular recognition mechanisms. In conclusion, the related challenges and gaps are given to offer ideas for future research focussing on MIPs for fluoroquinolones.

Emerging Contaminants in Seafront Zones. Environmental Impact and Analytical Approaches

Some chemical substances have the potential to enter the coastal and marine environment and cause adverse effects on ecosystems, biodiversity and human health. For a large majority of them, their fate and effects are poorly understood as well as their use still unregulated. Finding effective and sustainable strategies for the identification of these emerging and/or anthropogenic contaminants that might cause polluting effects in marine environments to mitigate their adverse effects, is of utmost importance and a great challenge for managers, regulators and researchers. In this review we will evaluate the impact of emerging contaminants (ECs) on marine coastal zones namely in their ecosystems and biodiversity, highlighting the potential risks of organic pollutants, pharmaceuticals and personal care products. Emerging microextraction techniques and high-resolution analytical platforms used in isolation, identification and quantification of ECs will be also reviewed.