Rapid and sensitive magnetoelastic biosensors for the detection of Salmonella typhimurium in a mixed microbial population

Magnetoelastic Monitoring System for Tracking Growth of Human Mesenchymal Stromal Cells

Magnetoelastic sensors, which undergo mechanical resonance when interrogated with magnetic fields, can be functionalized to measure various physical quantities and chemical/biological analytes by tracking their resonance behaviors. The unique wireless and functionalizable nature of these sensors makes them good candidates for biological sensing applications, from the detection of specific bacteria to tracking force loading inside the human body. In this study, we evaluate the viability of magnetoelastic sensors based on a commercially available magnetoelastic material (Metglas 2826 MB) for wirelessly monitoring the attachment and growth of human mesenchymal stromal cells (hMSCs) in 2D in vitro cell culture. The results indicate that the changes in sensor resonance are linearly correlated with cell quantity. Experiments using a custom-built monitoring system also demonstrated the ability of this technology to collect temporal profiles of cell growth, which could elucidate key stages of cell proliferation based on acute features in the profile. Additionally, there was no observed change in the morphology of cells after they were subjected to magnetic and mechanical stimuli from the monitoring system, indicating that this method for tracking cell growth may have minimal impact on cell quality and potency.

Multilayer Heterogeneous Membrane Biosensor Based on Multiphysical Field Coupling for Human Serum Albumin Detection

A factor closely associated with renal disease status in clinical diagnosis is abnormal human serum albumin (HSA) concentration levels in human body fluids urine, serum, etc. The surface stress biosensor was developed as a new type of biosensor to detect protein molecule concentration and has a wide range of clinical applications. However, further sensitivity improvement is required to achieve higher detection performance. Herein, MXene/PDMS/Fe₃O₄/PDMS of the multilayer heterogeneous membrane biosensor (MHBios) based on the coupling of the magnetic field, electric field, and surface stress field was successfully developed to achieve high sensitivity HSA detection through magnetic sensitization. The modified antibody specifically binds to HSA at the AuNP layer, allowing the biosensor to convert the surface stress caused by PDMS film deformation into an electrical signal. When the biosensor was exposed to a uniform magnetic field, the conductive path of the conductive layer was reshaped further as the magnetic force amplified the deformation of the PDMS film, enhancing the conversion of biological signals to electrical signals. The results exhibited that the detection limit (LOD) of the MHBios was 78 ng/mL when HSA concentration was 0-50 μg/mL, which was markedly lower than the minimum diagnostic limit of microalbuminuria. Furthermore, the MHBios detected HSA in actual samples, confirming the potential for early disease screening.

Magnetoelastic Sensor Optimization for Improving Mass Monitoring

Magnetoelastic sensors, typically made of magnetostrictive and magnetically-soft materials, can be fabricated from commercially available materials into a variety of shapes and sizes for their intended applications. Since these sensors are wirelessly interrogated via magnetic fields, they are good candidates for use in both research and industry, where detection of environmental parameters in closed and controlled systems is necessary. Common applications for these sensors include the investigation of physical, chemical, and biological parameters based on changes in mass loading at the sensor surface which affect the sensor’s behavior at resonance. To improve the performance of these sensors, optimization of sensor geometry, size, and detection conditions are critical to increasing their mass sensitivity and detectible range. This work focuses on investigating how the geometry of the sensor influences its resonance spectrum, including the sensor’s shape, size, and aspect ratio. In addition to these factors, heterogeneity in resonance magnitude was mapped for the sensor surface and the effect of the magnetic bias field strength on the resonance spectrum was investigated. Analysis of the results indicates that the shape of the sensor has a strong influence on the emergent resonant modes. Reducing the size of the sensor decreased the sensor’s magnitude of resonance. The aspect ratio of the sensor, along with the bias field strength, was also observed to affect the magnitude of the signal; over or under biasing and aspect ratio extremes were observed to decrease the magnitude of resonance, indicating that these parameters can be optimized for a given shape and size of magnetoelastic sensor.

Detecting Biothreat Agents: From Current Diagnostics to Developing Sensor Technologies

Although a fundamental understanding of the pathogenicity of most biothreat agents has been elucidated and available treatments have increased substantially over the past decades, they still represent a significant public health threat in this age of (bio)terrorism, indiscriminate warfare, pollution, climate change, unchecked population growth, and globalization. The key step to almost all prevention, protection, prophylaxis, post-exposure treatment, and mitigation of any bioagent is early detection. Here, we review available methods for detecting bioagents including pathogenic bacteria and viruses along with their toxins. An introduction placing this subject in the historical context of previous naturally occurring outbreaks and efforts to weaponize selected agents is first provided along with definitions and relevant considerations. An overview of the detection technologies that find use in this endeavor along with how they provide data or transduce signal within a sensing configuration follows. Current "gold" standards for biothreat detection/diagnostics along with a listing of relevant FDA approved in vitro diagnostic devices is then discussed to provide an overview of the current state of the art. Given the 2014 outbreak of Ebola virus in Western Africa and the recent 2016 spread of Zika virus in the Americas, discussion of what constitutes a public health emergency and how new in vitro diagnostic devices are authorized for emergency use in the U.S. are also included. The majority of the Review is then subdivided around the sensing of bacterial, viral, and toxin biothreats with each including an overview of the major agents in that class, a detailed cross-section of different sensing methods in development based on assay format or analytical technique, and some discussion of related microfluidic lab-on-a-chip/point-of-care devices. Finally, an outlook is given on how this field will develop from the perspective of the biosensing technology itself and the new emerging threats they may face.

Magneto-elastic biosensors: Influence of different thiols on pathogen capture efficiency

Magneto-elastic biosensors have mass sensitivity to biological species, offering reliability and reproducibility in the detection of pathogens such as Escherichia coli. In this work, amorphous ribbons of Metglas 2826MB3 were coated with layers of Cr and Au by DC magnetron sputtering and cut to 5mm×1mm. The influence of different thiols on captured pathogens was studied. The compounds cystamine (CYS), cysteamine (CYSTE) and mercaptopropionic acid (MPA) were deposited on Au-covered surfaces, followed by antibodies. The roughness parameters Ra and Rq were determined using atomic force microscopy (AFM) and micrographs from scanning electron microscopy with a field emission gun (FESEM) were also utilized. Biosensors formed with MPA showed an increased efficiency for attracting E. coli compared to biosensors with CYS and CYSTE, but large standard deviations were observed, making reproducibility and reliability difficult for that biosensor. Sensors tested with CYSTE showed greater efficiency and a lower detection limit than sensors with CYS. The results indicated that the size of the carbon chain and the terminal grouping influence the effectiveness of immobilization on magneto-elastic biosensors.

Detection of Salmonella Typhimurium on Spinach Using Phage-Based Magnetoelastic Biosensors

Phage-based magnetoelastic (ME) biosensors have been studied as an in-situ, real-time, wireless, direct detection method of foodborne pathogens in recent years. This paper investigates an ME biosensor method for the detection of Salmonella Typhimurium on fresh spinach leaves. A procedure to obtain a concentrated suspension of Salmonella from contaminated spinach leaves is described that is based on methods outlined in the U.S. FDA Bacteriological Analytical Manual for the detection of Salmonella on leafy green vegetables. The effects of an alternative pre-enrichment broth (LB broth vs. lactose broth), incubation time on the detection performance and negative control were investigated. In addition, different blocking agents (BSA, Casein, and Superblock) were evaluated to minimize the effect of nonspecific binding. None of the blocking agents was found to be superior to the others, or even better than none. Unblocked ME biosensors were placed directly in a concentrated suspension and allowed to bind with Salmonella cells for 30 min before measuring the resonant frequency using a surface-scanning coil detector. It was found that 7 h incubation at 37 °C in LB broth was necessary to detect an initial spike of 100 cfu/25 g S. Typhimurium on spinach leaves with a confidence level of difference greater than 95% (p < 0.05). Thus, the ME biosensor method, on both partly and fully detection, was demonstrated to be a robust and competitive method for foodborne pathogens on fresh products.

Biocompatibility and degradation of gold-covered magneto-elastic biosensors exposed to cell culture

Magneto-elastic materials (ME) have important advantages when applied as biosensors due to the possibility of wireless monitoring. Commercial Metglas 2826MB3™ (FeNiMoB) is widely used, however sensor stabilization is an important factor for biosensor performance. This study compared the effects of biocompatibility and degradation of the Metglas 2826MB3™ alloy, covered or not with a gold layer, when in contact with cell culture medium. Strips of amorphous Metglas 2826MB3™ were cut and coated with thin layers of Cr and Au, as verified by Rutherford Backscattering Spectroscopy (RBS). Using Inductively Coupled Plasma-Optical Emission Spectrometry (ICP-OES), the presence of metals in the culture medium was quantitatively determined for up to seven days after alloy exposure. Biocompatibility of fibroblast Chinese Hamster Ovary (CHO) cultures was tested and cytotoxicity parameters were investigated by indirect means of reduction of MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) at 1, 2 and 7 days. Cell death was further evaluated through in situ analysis using Acridine Orange/Ethidium Bromide (AO/EB) staining and images were processed with ImageJ software. Ions from Metglas(®) 2826MB3™ induced a degradation process in living organisms. The cytotoxicity assay showed a decrease in the percentage of live cells compared to control for the ME strip not coated with gold. AO/EB in situ staining revealed that most of the cells grown on top of the gold-covered sensor presented a normal morphology (85.46%). Covering ME sensors with a gold coating improved their effectiveness by generating protection of the transducer by reducing the release of ions and promoting a significant cell survival.

Label-free as-grown double wall carbon nanotubes bundles for Salmonella typhimurium immunoassay

Background

A label-free immunosensor from as-grown double wall carbon nanotubes (DW) bundles was developed for detecting Salmonella typhimurium. The immunosensor was fabricated by using the as-grown DW bundles as an electrode material with an anti-Salmonella impregnated on the surface. The immunosensor was electrochemically characterized by cyclic voltammetry. The working potential (100, 200, 300 and 400 mV vs. Ag/AgCl) and the anti-Salmonella concentration (10, 25, 50, 75, and 100 μg/mL) at the electrode were subsequently optimized. Then, chronoamperometry was used with the optimum potential of 100 mV vs. Ag/AgCl) and the optimum impregnated anti-Salmonella of 10 μg/mL to detect S. typhimurium cells (0-10⁹ CFU/mL).

Results

The DW immunosensor exhibited a detection range of 10² to 10⁷ CFU/mL for the bacteria with a limit of detection of 8.9 CFU/mL according to the IUPAC recommendation. The electrode also showed specificity to S. typhimurium but no current response to Escherichia coli.

Conclusions

These findings suggest that the use of a label-free DW immunosensor is promising for detecting S. typhimurium.

Scano-magneto immunoassay based on carbon nanotubes/gold nanoparticles nanocomposite for Salmonella enterica serovar Typhimurium detection

To improve sensitivity of S. enterica serovar Typhimurium detection, multiwalled carbon nanotubes (MWCNTs) and gold nanoparticles (AuNPs) were combined and used as a label to amplify signal in a scanometric based assay. In this study, the MWCNTs/AuNPs nanocomposite was fabricated by directly assemble of Au(3+) to MWCNTs and allowed growing of AuNPs along the MWCNTs surface. This MWCNTs/AuNPs nanocomposite was then attached to anti-S. typhimurium antibody (MWCNTs/AuNPs/Ab(1)) and used as a detecting molecule. Upon binding to Salmonella, they were pre-concentrated by magenetic beads/antibody (MBs/Ab(2)) forming a sandwich immuno-complex which is later spotted on a nitrocellulose membrane coated slide. Silver reduction was applied to amplify signal. The detection limit of 42CFU/ml was achieved when 2% BSA was used as a blocking agent. Given different types of real samples testing, chicken broth was found to give lowest detection limit, followed by orange juice low fat and whole milk. Selectivity testing was performed by using Escherichia coli as interference and found slightly cross-reactivity which could be due to specificity of the Ab used. By virtue of using a slide for multi-samples spotting and a flatbed scanner for signal-read out acquisition, this scano-magneto immunoassay could enable low-cost detection as well as high throughput screening.

Rapid detection of E. coli O157:H7 on turnip greens using a modified gold biosensor combined with light microscopic imaging system

This research aims to demonstrate the feasibility of a modified gold biosensor to detect E. coli O157:H7 in leafy turnip greens. The gold biosensor was modified with dithiobis-succinimidyl propionate (DSP) and/or protein A or G. The gold biosensor modified with DSP (Gold-DSP) was combined with a light microscopic imaging system (LMIS). The optimal concentration and specificity of anti-E. coli O15 polyclonal antibodies (pAbs) on the biosensor were determined. The reliability of Gold-DSP biosensor was investigated by determining the sensitivity, specificity, and limit of detection (LOD) of the Gold-DSP combined with LMIS. The Gold-DSP combined with LMIS was applied to turnip greens for E. coli O157:H7 detection. The modification of Gold biosensor with DSP significantly increased the detected number of E. coli O157:H7. The specificity of pAbs was sufficient to react with target E. coli O157:H7 among the tested bacterial culture. The optimum concentration of pAbs was determined as 200 μg/mL. The sensitivity, specificity, and LOD of Gold-DSP combined with LMIS were determined as 100%, 90%, and 10(3) CFU/25 mm(2) , respectively. When applied to turnip greens, the Gold-DSP combined with LMIS could detect 2641 ± 394 and 15383 ± 3853 cell/mm(2) with the initial concentrations of 10(1) and 10(2) CFU/25 g turnip greens, respectively, after 10 h-enrichment. Overall, this research suggested that the Gold-DSP combined with LMIS could be used to detect E. coli O157:H7 on turnip greens qualitatively and quantitatively.

Time domain characterization of magnetoelastic sensors: A pulse method for resonance frequency determination

This paper presents a pulse method for determination of resonance frequency of magnetoelastic sensors. The method eliminates the bias field that is necessary in previous methods and also allows fast and accurate detection. The stability tests of the system show an average standard deviation of 129 Hz and an average drift of -10.4 Hz/h. This system allows simultaneous detection of two sensors. A simulation of the operation of one and two sensors was shown to be very similar to the real data plots from the test system. Real tests have shown that adding a second sensor does not affect the resonance frequency of the first sensor. The effect of pulse magnetic field on the characteristics of the resonance signal, including resonance frequency, amplitude, and Q-value of frequency domain signal, has been studied and real time detection using magnetoelastic sensors was demonstrated in a flowing system.