Microwave-assisted synthesis of tetraethylenepentamine functionalized activated carbon with high adsorption capacity for Malachite green dye

Adsorption Behavior of Methylene Blue Onto Activated Coconut Shells: Kinetic, Thermodynamic, Mechanism and Regeneration of the Adsorbent

Adsorption techniques are widely used to remove some classes of pollutants from waters, especially those which are not easily biodegradable. The removal of Methylene blue (MB), as a pollutant, from waste waters of textile, paper, printing and other industries has been addressed by the researchers. The aim of this study is to eliminate MB by Activated Coconut Shells (ACS) produced at low cost by adsorption in batch mode. The ACS was characterized by the FTIR spectroscopy and point of zero charge (pHpzc: 5.06). Some examined factors were found to have significant impacts on the MB uptake of ACS like the initial dye concentration Co (40-120 mg/L), solution pH (2-8), ACS dose (1-12 g/L), agitation speed (50-500 r/min), particles size (1.0-1.2 mm) and temperature (298-333 K). The best capacity was found at pH 6 with an adsorbent dose 8 g/L, an agitation speed 200 r/min and a contact time of 60 min. Modeling Kinetics and Isotherms shows that the pseudo-second-order kinetic model with R 2 (0.935 -0.998) and Langmuir adsorption isotherm model provide better fitness to the experimental data with the maximum adsorption capacity of 30.30 mg/g at 25°C. The separation factor RL (0.933-0.541) in the concentration range studied (10-120 mg/L) shows a favorable adsorption. The isotherms at different temperatures have been used for the determination of the free energy ΔG° (198-9.72 kJ/mol); enthalpy ΔH° (82.082 kJ/mol) and entropy ΔSo (245.689 J/K mol) to predict the nature of MB adsorption process. The positive values of (ΔGo) and (ΔHo) indicate a non-spontaneous and endothermic MB adsorption with a chemisorption. The adsorbent elaborated from Coconut Shells was found to efficient and suitable for the removal of MB dye from aqueous solutions, due to its availability, low cost preparation and good uptake capacity.

Investigation of Eucalyptus camaldulensis and Tamarix aphylla species' capacities for methylene blue removal in wastewater and heavy metal remediation in soil

In the contemporary landscape, the reuse of wastewater holds paramount significance. Concurrently, wastewater carries an array of pollutants encompassing chemical dyes and heavy metals. This study delves into the potential of Tamarix aphylla (TA) and Eucalyptus camaldulensis (EC) species for mitigating heavy metals in soil and eliminating methylene blue dye (MB) from wastewater. The research begins with assessing the dye adsorption process, considering pivotal factors such as initial pH, adsorbent dosage, initial dye concentration, and contact time. Outcomes reveal EC's superiority in dye removal compared to TA. As a bioremediation agent, EC exhibits a 90.46% removal efficacy for MB within 15 min, with pH 7.0 as the operative condition. Equilibrium analysis employs Temkin (T), Freundlich (F), and Langmuir (L) isotherms, revealing an excellent fit with the L isotherm model. The study delves further by probing surface adsorption kinetics through pseudo-first-order (PFO) and pseudo-second-order (PSO) models. Furthermore, to discern the divergent impacts of EC and TA on soil heavy metal reduction, soil samples were collected from three distinct zones: an untouched control area, alongside areas where EC and TA were cultivated at the Yazd wastewater site in Iran. Heavy metal levels in the soil were meticulously assessed through rigorous measurement and statistical scrutiny. The findings spotlight TA-cultivated soil as having the highest levels across all examined factors. Ultimately, EC emerges as the superior contender, proficiently excelling in both MB eliminations from wastewater and heavy metal amelioration in the soil, positioning it as the preferred phytoremediation agent.

Tetraethylenepentamine-Grafted Amino Terephthalic Acid-Modified Activated Carbon as a Novel Adsorbent for Efficient Removal of Toxic Pb(II) from Water

In this study, a new composite, tetraethylenepentamine (TEPA), was incorporated into amino terephthalic acid-modified activated carbon (ATA@AC) through a one-pot integration of TEPA with the COOH moiety of ATA@AC. This process resulted in the creation of a TEPA@ATA@AC composite for Pb(II) removal from an aquatic environment. Several techniques, including SEM, EDX, FT-IR, TGA, XRD, and Zeta potential, were employed to emphasize the chemical composition, morphology, and thermal durability of the as-synthesized TEPA@ATA@AC composite. The impact of experimental variables on the adsorption of Pb(II) ions was studied using batch adsorption. The uptake assessment suggested that the TEPA@ATA@AC composite exhibited superior Pb(II) removal performance with high removal efficiency (97.65%) at pH = 6.5, dosage = 0.02 g, equilibrium time = 300 min, and temperature = 298 K. The isotherm data exhibited good conformity with the Langmuir isotherm model, whereas the kinetics data displayed strong agreement with both pseudo-first-order and pseudo-second-order kinetics models. This reflected that the Pb((II) uptake by the TEPA@ATA@AC composite was caused by physisorption coupled with limited chemisorption. The greatest monolayer uptake capacity of the TEPA@ATA@AC composite was 432.8 mg/g. The thermodynamic findings indicated that the Pb(II) uptake on the TEPA@ATA@AC composite was an exothermic and feasible process. After five adsorption-desorption runs, the TEPA@ATA@AC composite maintained a superior uptake capacity (83.80%). In summary, the TEPA@ATA@AC composite shows promise as a potent adsorbent for effectively removing Cr(VI) from contaminated water, with impressive removal efficiency.

Synthesis of hybrid framework of tenorite and octahedrally coordinated aluminosilicate for the robust adsorption of cationic and anionic dyes

Adsorption is an important process for the industrial dye effluent treatment. Many adsorbents are employed such as activated carbon, metal oxide, molecular sieves etc. All those adsorbents are having their own setbacks like longer adsorption time and lower adsorption capacity. So development of fast adsorption and higher adsorption capacity is very much essential. In this view, we synthesized hybrid crystal system of tenorite and aluminosilicate framework (CuO@AS) for the faster adsorption. It is characterized by FT-IR, HRTEM and WAXRD. WAXRD proved the hybridization of two crystal systems viz tenorite & alumina in monoclinic phase and silica in trigonal phase. The crystal structure drawn based on the WAXRD data. It is observed that the tenorite and aluminosilicate framework are separate, but they are interlinked through Cu-O-Al and Cu-O-Si bond. This interconnection makes the aluminium in six coordination and Cu in four coordination. Aluminium and copper has 3 and 2 Brønsted acid sites respectively. Moreover, copper has three more OH group, so totally 5 H⁺ and 3 OH^- sites in copper and aluminium are responsible for the faster adsorption with high adsorption capacity compared to reported literature. To test the adsorption tendency, Victoria Blue (VB) and Metanil Yellow (MY) dyes are employed at room temperature. The rate constant of Pseudo-second order kinetics for the VB and MY are 0.002462 g mg^-1 min^-1 and 0.001619 g mg^-1 min^-1 which indicated faster adsorption of VB than MY. Moreover, total adsorption capacity for VB (636 mg/g) is higher than MY (52 mg/g). This is due to the hybridization of tenorite and aluminosilicate. Thermodynamic data such as ΔG°, ΔH° and ΔS° revealed that the adsorption is spontaneous, chemisorption and highly disordered in the adsorbent-adsorbate interface. This disorderness is due to the disordered pores present in the material.

Intelligent modelling for the elimination of lanthanides (La3+, Ce3+, Nd3+ and Eu3+) from aqueous solution by magnetic CoFe2O4 and CoFe2O4-GO spinel ferrite nanocomposites

In this research, a novel CoFe₂O₄-GO (Graphen Oxide) resulting from the combination of high applicable magnetic and organic base materials and synthesized with a simple and fast co-precipitation route was synthesized for the REEs (Rare Earth Elements) extraction. This adsorbent could remove the La³⁺, Ce³⁺, Nd³⁺ and Eu³⁺ by maximum adsorption capacity of 625, 626, 714.2, 1111.2 mg/g at optimized pH = 6, respectively. A data-driven model was obtained using Group Method of Data Handling (GMDH)-based Neural Network to estimate the adsorption capacity of these LREEs as a function of time, pH, temperature, adsorbent ζ (zeta)- potential, initial concentration of lanthanides ions, and ε which is defined by the physico-chemical properties of lanthanides. The results clearly indicated that the model estimate the experimental values with good deviation (mostly less than 10%) and it can be used for the prediction of the results from other similar researches with less than 25% deviation. The results of sensitivity analysis indicated that the adsorption capacity is more sensitive to pH of the solution, temperature, and ε. Finally, the desorption studies showed an excellent removal efficiency (97%) at least for three adsorption-desorption cycles. These results claimed that the CoFe₂O₄-GO is a highly efficient adsorbent for the REEs extraction.

Low-temperature synthesis of functionalized activated carbon from blackboard (Alstonia scholaris) with improved selectivity for 2-methylpyridine removal: batch and column analyses

Coal tar industry has been reported to discharge 2-methylpyridine (2Mp) in concentrations up to 150 mg L^-1. For removal of 2Mp, activated carbon was synthesized from blackboard tree ground bark (BA) by the novel technique of prior cooling (which helped decrease heat generation and volatile gas emission). The material was successfully functionalized with carboxylic group which enhanced 2Mp uptake. Batch sorption of 2Mp was carried out on both BA and carboxyl functionalized BA (CFA). Acetonitrile-water (55:45) was used as eluent in uHPLC quantification of 2Mp. Interaction mechanism of 2Mp with both sorbents was studied by using characterization techniques (SEM, FTIR and EDS). Carboxyl groups present on CFA were found to interact with 2Mp molecules, leading to their removal from synthetic solution. Carboxylation helped in lowering the intrinsic moisture content of the sorbent. Proton leaching from carboxyl groups of CFA was found to be negligible. Specific surface areas for CFA and BA were found as 211.15 m² g^-1 and 156.32 m² g^-1, respectively. Batch experimentation showed that CFA had twice the adsorption capacity compared to BA (27.0 and 15.5 mg g^-1, respectively). Pseudo-second-order kinetics and Langmuir isotherm-based equilibria were observed. Intraparticle diffusion was the rate-limiting step. Top-down fixed bed studies were performed using a 2-cm-diameter column by varying flow rate, bed depth and 2Mp concentration, respectively. The Thomas model could successfully emulate the steep slopes of the breakthrough curves, implying good sorbent saturation.

Epichlorohydrin and tripolyphosphate-crosslinked chitosan-kaolin composite for Auramine O dye removal from aqueous solutions: Experimental study and DFT calculations

Chitosan (Ch, a natural polymer) and kaolin (K, a natural mineral) composite (Ch-K) was produced with the help of two crosslinkers, epichlorohydrin and tripolyphosphate, and then moulded into uniform beads in tripolyphosphate solution. The synthesis was proved by the analyses involving FT-IR and SEM-EDX. The beads were then used as the natural adsorbent for removal of the auramine O (AO), a frequently-used industrial dye, in aqueous solutions. Adsorbent performance of the Ch-K composite for AO dye molecules was optimized: 500 mg L^-1 at pH 7.5 at 25 °C. The Langmuir model found 0.118 mol kg^-1 for the maximum adsorption capacity of the Ch-K and the D-R isotherm model showed that the nature of the adsorption process was physical. Kinetics of the adsorption could be explained by using both IPD (intraparticle diffusion) and PSO (pseudo second order) models. Thermodynamic parameters demonstrated that the behaviour of the adsorption was an endothermic and spontaneous. The activity of the composite adsorbent was recovered (88%) after the five sequential adsorption/desorption cycles. Supported by experimental findings, the results obtained from in silico modeling at M06-2X/6-31+G (d,p) level helped hypothesise a mechanism for the formation of the Ch-K composite, and shed some light onto the adsorption behaviour of AO dye by assuming several favourable intermolecular interactions.

Synthesis of EDTA-functionalized graphene oxide-chitosan nanocomposite for simultaneous removal of inorganic and organic pollutants from complex wastewater

Discharging of inorganic and organic pollutants creates a serious threat to the human health and the environment. In the current work, we have synthesized Ethylenediaminetetraacetic acid (EDTA) functionalized graphene oxide-chitosan nanocomposite (GO-EDTA-CS) for simultaneous removal of inorganic (i.e., mercury (Hg(II) and copper (Cu(II)) and organic pollutants (i.e., methylene blue (MB) and crystal violet (CV)) from wastewater via adsorption process. The structural, functional, morphological, elemental compositions, surface area and thermal properties of the synthesized nanocomposite were identified using powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), field scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), Brunauer-Emmett-Teller (BET), and thermogravimetric analyzer (TGA), respectively. Different batch adsorption experiments such as pH effect, contact time, initial pollutants concentration, reusability etc. were studied in monocomponent system to optimize the results. The adsorption process apparently followed pseudo-second-order (PSO) kinetics for both pollutants, however the adsorption kinetics was also explained by the intra-particle diffusion model. The isotherm data for both metals ions and dyes were well fit by the Langmuir isotherm model. The maximum adsorption capacities of the adsorbent were determined 324 ± 3.30 130 ± 2.80, 141 ± 6.60, and 121 ± 3.50 mg g^-1 for Hg(II), Cu(II), MB, and CV, respectively. The excellent adsorption capacity was attributed to the availability of various active functional groups (e.g., -COOH, -OH, -NH₂, etc.) on the adsorbent. The EDS, elemental mapping and FTIR analysis performed before and after the adsorption of heavy metals and dyes by GO-EDTA-CS confirmed the simultaneous adsorption of the pollutants. Moreover, GO-EDTA-CS could maintain its adsorption capacity for both inorganic and organic pollutants even after seven cycles of adsorption-desorption, indicating itself a promising adsorbent for practical wastewater treatment containing both inorganic and organic toxic pollutants.

Preparation of Activated Carbon Derived from Jordanian Olive Cake and Functionalized with Cu/Cu2O/CuO for Adsorption of Phenolic Compounds from Olive Mill Wastewater

Olive oil production generates solid and liquid wastes that cause various environmental problems due to their high phenols and polyphenols load. Although many treatment methods were investigated to manage these wastes, more research is still needed to identify simple and cost-effective approaches. In this study, activated carbon (AC) was prepared from olive cake waste and functionalized with Cu/Cu₂O/CuO for efficient and selective removal of phenolic content from olive mill wastewater (OMW). AC media were characterized by scanning electron/dispersive X-ray spectroscopy (SEM-EDS), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectrometry, and Brunauer-Emmett-Teller (BET) surface area analysis. The optimum adsorption parameters were investigated, and the adsorption isotherms, thermodynamics, and kinetics were determined. The adsorption of phenols onto copper oxide AC was best described by the Langmuir adsorption with maximum adsorption capacity of 13.9, 12.7, and 9.9 mg/g at 311, 302, and 293 K, respectively. The adsorption reaction was found to be spontaneous and endothermic where ∆H° and ∆G° were found to be 30.104 kJ/mol and -1.765, -2.839, and -3.723 (kJ/mol) at 311, 302, and 293 K, respectively. In addition, the kinetics data were perfectly fit by the pseudo-second-order model. The activated product derived from recyclable olive cake and enriched with inorganic functionality can offer a cost-effective treatment solution for OMW; thus, reducing both the liquid and solid waste generated from the olive mill industry.

Diversity of Synthetic Dyes from Textile Industries, Discharge Impacts and Treatment Methods

Natural dyes have been used from ancient times for multiple purposes, most importantly in the field of textile dying. The increasing demand and excessive costs of natural dye extraction engendered the discovery of synthetic dyes from petrochemical compounds. Nowadays, they are dominating the textile market, with nearly 8 × 105 tons produced per year due to their wide range of color pigments and consistent coloration. Textile industries consume huge amounts of water in the dyeing processes, making it hard to treat the enormous quantities of this hazardous wastewater. Thus, they have harmful impacts when discharged in non-treated or partially treated forms in the environment (air, soil, plants and water), causing several human diseases. In the present work we focused on synthetic dyes. We started by studying their classification which depended on the nature of the manufactured fiber (cellulose, protein and synthetic fiber dyes). Then, we mentioned the characteristics of synthetic dyes, however, we focused more on their negative impacts on the ecosystem (soil, plants, water and air) and on humans. Lastly, we discussed the applied physical, chemical and biological strategies solely or in combination for textile dye wastewater treatments. Additionally, we described the newly established nanotechnology which achieves complete discharge decontamination.

Dye Removal from Colored Textile Wastewater Using Seeds and Biochar of Barley (Hordeum vulgare L.)

Phenol red (X-PR) and malachite green carbinol (MGC) are two textile finishing dyes, which are present in aquatic environments through industrial effluents. Due to the toxic nature of both dyes, they are harmful to human health. In the present study, two materials, barley seeds and the biochar of barley (Hordeum vulgare L.), were used to remove the dyes in an aqueous solution. The materials used are characterized by AFM, FTIR, SEM, XRD and EDX techniques. In this study, the parameters studied are the adsorbent dose, pH, initial adsorbate concentration and contact time. The maximum equilibrium time was found to be 90 min for all dyes. Kinetic studies revealed that the adsorption of X-PR and MGC on barley seeds (BS-HVL) and the biochar of barley (BC-HVL) followed pseudo-second-order kinetics and that both porous and intraparticle diffusion mechanisms were involved. The adsorption equilibrium data were well fitted to the Langmuir and Freundlich isotherm model for both materials, and the maximum adsorption capacity of monolayer and multilayers for X-PR and MGC were 71.642 mg g−1 and 50 mg g−1 on BS-HVL, and 44.843 mg g−1 and 121.95 mg g−1 on BC-HVL, respectively. The thermodynamic results reveal that the dye removal on barley was endothermic and spontaneous in nature.

Facile preparation of robust dual MgO-loaded carbon foam as an efficient adsorbent for malachite green removal

This study developed a facile approach for the fabrication of dual MgO-loaded carbon foam (DMCF) via carbonization of a cured MgO/cyanate ester resin mixture, which underwent self-foaming of the resin followed by the carbothermal reduction of MgO. The features of the prepared DMCF prepared were characterized by FESEM, TEM, XRD, FTIR, XPS and so on, and the effects of adsorption conditions, adsorption isotherms, kinetics, and thermodynamics on malachite green (MG) removal using the DMCF as adsorbents were investigated through batch adsorption experiments. Results demonstrate that the DMCF possesses a unique dual loading of MgO particles which are not only loaded onto its foam walls but also filled within the walls with a graphene-wrapped core-shell structure. The experimental maximum adsorption capacity of MG reaches up to 1874.18 mg/g with a partition coefficient of 10.87 mg/g/μM. The adsorption process can be better described with Langmuir, pseudo-second-order, and intraparticle diffusion models. Moreover, the DMCF exhibits a removal percentage of 84.85% after five reuses, indicating that it is an efficient and promising adsorbent for MG adsorption.

Dye removal from water and wastewater by nanosized metal oxides - modified activated carbon: a review on recent researches

The conventional water and wastewater treatment methods are unable to provide up-to-data organized standards for drinking water and discharging effluents into natural ecosystems. Therefore, developing advanced and cost-effective methods to achieve published standards for water and wastewater and population needs are nowadays necessity. The important parts of this article are providing literature information about dyes and their effects on the environment and human health, adsorption properties and mechanism, adsorbent characteristics, and recent information on various aspects of modified activated carbons with nanosized metal oxides (AC- NMOs) in the removal of dyes. This review also summarized the effect of main environmental and operational parameters such as adsorbent dosage, pH, initial dye concentration, contact time, and temperature on the dye adsorption using AC-NMOs. Furthermore, the applied isotherm and kinetic models have been discussed.

Advanced development of dairy farm waste-based biocarbon-reinforced unsymmetrical structured bio-phenolic polybenzoxazine composites

In the present work, an attempt has been made to develop cow manure carbon-reinforced hybrid biophenol-based benzoxazine composites for antifouling coating applications. Bio-based benzoxazine with unsymmetrical molecular structure was synthesized using the mixture of a combination of cardanol and eugenol with diaminodiphenyl methane and paraformaldehyde, and the hybrid-benzoxazine obtained was characterized using different analytical techniques, viz., Fourier transform infrared, nuclear magnetic resonance and MALDI mass. Bio-based benzoxazine was further reinforced with varying weight percentages (1, 3 and 5 wt%) of biocarbon derived from cow manure to obtain hybrid composite coatings. The hybrid benzoxazine matrix and composites were studied for their thermal behaviour, contact angle (CA), morphology, corrosion-resistant behaviour and antifouling character to utilize them as coatings materials for different industrial applications. Results obtained from different studies inferred that the biocarbon-reinforced composites possess an enhanced value of glass transition temperature (249°C), high char yield (38.4%), improved CA (105.6°), higher efficiency of corrosion protection against mild steel surface (98%) and improved antimicrobial activity.

Magnetic N-doped carbon aerogel from sodium carboxymethyl cellulose/collagen composite aerogel for dye adsorption and electrochemical supercapacitor

Nitrogen-doped carbon aerogels derived from sodium carboxymethyl cellulose were prepared via a multistep approach involving sol-gel, freeze-drying, carbonization, and KOH activation processes; ferric trichloride and collagen were used as cross-linking agent and nitrogen source, respectively. The carbon aerogels exhibited well-developed porous three-dimensional morphologies, high specific surface areas, and excellent magnetic properties. When applied as electrode material, the CA-N0.5 showed a specific capacitance of 185.3F/g at the current density of 0.5A/g in a 6M KOH electrolyte. The specific capacitance retention was 90.2% after 5000 charge/discharge cycles, indicating excellent cycling stability. In addition, the carbon aerogels showed excellent adsorption capacities of 238.2 and 230.4mg/g for malachite green and methylene blue, respectively. These results suggest that N-doped carbon aerogels may be utilized as electrodes in supercapacitors as well as highly efficient contaminant adsorbents in aqueous solutions.

Treatment of dye wastewater using an ultrasonic aided nanoparticle stacked activated carbon: Kinetic and isotherm modelling

The present work explains the biosorption of malachite green dye from aquatic systems by nano zero valent iron stacked activated carbon (NZVI-AC), which was prepared by dual surface modification strategy. NZVI-AC was characterized by using FTIR, SEM-EDX, XRD and TGA. NZVI-AC exhibited efficient performance in dye biosorption properties. Experimental variables such as time, pH, dye concentration, temperature and biosorbent dosage influenced Langmuir adsorption capacity of 187.3 mg/g. The present biosorption system was best described by pseudo-first order kinetics. The dye was completely knocked out of the solution within 60 min at equilibrium. The thermodynamic behaviour of NZVI-AC was exothermic, feasible and spontaneous. Experimental data was engaged to validate new solid-liquid phase equilibrium model, showing the average absolute relative deviation 7.72%. Hence the procedure was non-toxic, potential to retain biosorbent from the solution, applicable for multiple cycles. In context, NZVI-AC can be recommended for the treatment of dyes from industrial effluent.

Date stone based activated carbon/graphite electrode for catechol analysis: physico-chemical properties and application in beverage samples

The purpose of this paper is the modification of a carbon paste electrode (CPE) with activated carbon synthesized from date stones using a pyrolysis system followed by physical activation.

Role of functional groups on protonated de-oiled soybean involved in triclosan biosorption from aqueous solution

The contribution of functional groups such as amine, carboxyl, sulfhydryl, phosphate and lipids on protonated de-oiled soybean (PDOS) to triclosan (TCS) biosorption was evaluated by means of chemical modification.