Trace determination of Cr(III) and Cr(VI) species in water samples via dispersive liquid-liquid microextraction and microvolume UV–Vis spectrometry. Thermodynamics, speciation study

Miniaturized 3D-printed hand-operable dispersive sample pretreatment device with replaceable chitosan/polydopamine thin film metal sorbent for enhanced metal analysis

To address the increasing demand for sensitive and selective sample preparation methods for metal analysis; preconcentration of intended analyte from complex sample matrices before analysis is required to improve the performance of analysis instruments. In this study, we have engineered a sustainable and portable syringe-based hand-operable three-dimensionally (3D) printed sample pretreatment apparatus equipped with a replaceable bio-based thin- film metal sorbent. This device effectively addresses the challenges of sample matrix interference in metal analysis. A metal sorbent film composed of chitosan (CS) and polydopamine (PDA) leveraged the diverse functional groups in the CS/PDA matrix to significantly enhance the extraction efficiency for various metals. Our approach demonstrated excellent analytical performance, with coefficients of determination (R2) of 0.9982 for copper (Cu) and 0.996 for chromium (Cr). The method achieved low limits of detection (LOD) of 0.3 μg L-1 for Cr and 0.7 μg L-1 for Cu. Precision and practicality assessments using actual urine samples yielded satisfactory relative standard deviations (RSD%) ranging from of 1.6 %-8.5 % for both metals, indicating minimal interference from the sample matrix. Moreover, our approach exhibited robust performance even after seven consecutive extraction and desorption cycles, highlighting its sustainability and practical applicability for laboratory and on-site sample pretreatment.

An Effective Sol-Gel-Functionalized Polyurethane Foams Solid Platform Packed Minicolumns for Complete Extraction of Chromium (VI) from Water: Kinetic, Sorption Isotherms, Thermodynamic Study, and Analytical Utility

In the modern era, sol-gel plays a key role in the progress of a new generation of dispersive solid-phase microextractors (d-µ SPMEs) for the removal of organic and inorganic pollutants in complex matrices. Thus, the current study reports the use of sol-gel-functionalized polyurethane foams (PUFs) as a novel solid platform for complete extraction of chromium (VI) species from aqueous media. The planned protocol was based upon the complete extraction of the formed binary complex ion associates between the protonated ether and/or urethane groups of PUFs and chlorochromate anion [CrO3Cl]- aq in aqueous HCl (≥1M) medium in addition to H-bonding and the electrostatic π-π interaction that resulted between the CrO3Cl- and the silanol group (Si/ZrO2, Si-O-Zr) and siloxane (Si-O-Si) groups of the sol-gel. The impact of the analytical parameters (solution pH, natural mineral acids, shaking time, temperature, and chromium (VI) concentrations) was critically studied. At the optimal conditions, the uptake capacity of the established extractor (9.9 mg·g-1) was in agreement with the Langmuir adsorption capacity (12.08 mg·g-1) of the monolayer. The sorption data fitted well with the pseudo first-order kinetic model (R 2 = 0.9961) with an overall rate constant (k 1) of 0.081 min-1 and an equilibrium capacity (q e ) of 8.6 mg·g-1, which is in a good agreement with the experimental value (9.9 mg·g-1). The sorption of the oxyion [CrO3Cl]- aq onto the solid sorbent is an endothermic and spontaneous process as reflected from the values of ΔH (6.99 kJ·mol-1) and ΔG (-8.14 kJ·mol-1 at 293 K), respectively. The ΔS value (15.13 kJ·mol-1·K-1) reflects that the [CrO3Cl]- aq retention onto the sol-gel-treated PUFs sorbent proceeded in a more unplanned fashion. Sol-gel-treated PUFs sorbent-packed minicolumns were successfully used for the complete removal of trace levels of chromium (VI) species from water samples. Sorbed chromium (VI) species were recovered with NaOH (0.5 M) and analysed by spectrophotometry, which supports the utility of the sol-gel-treated PUFs as a low-cost solid extractor for water treatment.

Machine Learning Algorithms for Intelligent Decision Recognition and Quantification of Cr(III) in Chromium Speciation

Cr(III) is a common oxidation state of chromium, and its presence in the environment can occur naturally or as a result of human activities, such as industrial processes, mining, and waste disposal. This article explores the application of machine learning algorithms for the intelligent decision recognition and quantification of Cr(III) in chromium speciation. Three different machine learning models, namely, the Decision Tree (DT) model, the PCA-SVM (Principal Component Analysis-Support Vector Machine) model, and the LDA (Linear Discriminant Analysis) model, were employed and evaluated for accurate and efficient classification of chromium concentrations based on their fluorescence responses. Furthermore, stepwise multiple linear regression analysis was utilized to achieve a more precise quantification of trivalent chromium concentrations through fluorescence visualization. The results demonstrate the potential of machine learning algorithms in accurately detecting and quantifying Cr(III) in chromium speciation with implications for environmental and industrial applications in chromium detection and quantification. The findings from this research pave the way for further exploration and implementation of these models in real-world scenarios, offering valuable insights into various environmental and industrial contexts.

A Novel, Simple, and Reliable Spectrophotometric Determination of Total Hexavalent Chromium by Complexation with a New Reagent of Thiazole Linked to 2H-Chromen-2-One

Hexavalent chromium is a known environmental contaminant and carcinogen. In the current work, a simple, rapid, and reliable direct spectrophotometric method was used for the determination of total Cr (VI) in environmental samples. Acid-base equilibria and ionization constant (pKa) of the new reagent 3-(2-(2-(4-(trifluoromethyl)benzylidene)hydrazineyl) thiazol-4-yl)-2H-chromen-2-one (thiazole linked to 2H-chromen-2-one, TFZ) were investigated. The value of pKa for the reagent was found to be 7.6 which was initially reported. The reaction of the TFZ ligand with Cr (VI) was optimized to produce a highly absorbent complex at 370 nm and pH 7.0 within 1 min. With a correlation coefficient of 0.9994, the linear concentration range ranges from 2 to 20,000 ng·mL−1. The detection limit and quantification limit were 0.73 and 2.43 ng·mL−1, respectively. The method has high precision with relative standard deviations less than 1.0 and high accuracy with recovery of 100 ± 2%. A large excess of cations and anions did not interfere with the determination of Cr (VI). The proposed method was successfully applied to the determination of Cr (VI) in cement samples. The current method could be useful for the routine analysis of Cr (VI) in environmental labs.

Poly(carbazole-co-1,4-dimethoxybenzene): Synthesis, Electrochemiluminescence Performance, and Application in Detection of Fe3+

In this study, four polycarbazole derivatives (PCMB-Ds) with different alkyl side chains were designed and synthesized via Wittig–Horner reaction. A novel solid-phase electrochemiluminescence (ECL) system was prepared by immobilizing PCMB-D on an indium tin oxide (ITO) electrode with polyvinylidene fluoride (PVDF) in the presence of tripropylamine (TPrA). It could be found that the increase in alkyl side chain length had little effect on the ECL signal of PCMB-D, while the increase in the degree of polymerization (DP) greatly enhanced the ECL signal. Furthermore, the P-3/ITO ECL sensor based on the polyoctylcarbazole derivative (P-3) with the best ECL performance was successfully constructed and detected Fe³⁺ under the optimal experimental conditions. The ECL signal steadily diminished with the increased concentration of Fe³⁺ because of the competition and complexation between Fe³⁺ and P-3 under the condition of pH 7.4. This P-3/ITO platform could realize a highly sensitive and selective detection of Fe³⁺ with a wide detection range (from 6 × 10⁻⁸ mol/L to 1 × 10⁻⁵ mol/L) and low detection limit of 2 × 10⁻⁸ mol/L, which could allow the detection of Fe³⁺ in multiple scenarios, and would have a great application prospect.

Process enhancing strategies for the reduction of Cr(VI) to Cr(III) via photocatalytic pathway

This discourse aimed at providing insight into the strategies that can be adopted to boost the process of photoreduction of Cr(VI) to Cr(III). Cr(VI) is amongst the highly detestable pollutants; thus, its removal or reduction to an innocuous and more tolerable Cr(III) has been the focus. The high promise of photocatalysis hinged on the sustainability, low cost, simplicity, and zero sludge generation. Consequently, the present dissertation provided a comprehensive review of the process enhancement procedures that have been reported for the photoreduction of Cr(VI) to Cr(III). Premised on the findings from experimental studies on Cr(VI) reductions, the factors that enhanced the process were identified, dilated, and interrogated. While the salient reaction conditions for the process optimization include the degree of ionization of reacting medium, available photogenerated electrons, reactor ambience, type of semiconductors, surface area of semiconductor, hole scavengers, quantum efficiency, and competing reactions, the relevant process variables are photocatalyst dosage, initial Cr(VI) concentration, interfering ion, and organic load. In addition, the practicability of photoreduction of Cr(VI) to Cr(III) was explored according to the potential for photocatalyst recovery, reactivation, and reuse reaction conditions and the process variables.

Carbon Dots Derived from the Maillard Reaction for pH Sensors and Cr (VI) Detection

The Maillard reaction involves a series of complex reactions; fluorescent compounds have been considered as vital intermediate products of the reaction. In this article, carbon dots (CDs) based on the Maillard reaction (MR-CDs) were prepared with L-tryptophan and D-glucose, and they had excellent photoluminescence stability. MR-CDs showed stable pH-dependence behavior and exhibited an excellent linear response to pH in the range of 4.0–7.5 and 7.5–13.0, respectively. Under the masking effect of sodium fluoride for Fe(III), MR-CDs showed excellent selectivity and sensitivity for Cr (VI). The linear range of Cr(VI) was 0.2–50 μM and the limit of detection was 20 nM. (S/N ≥ 3). Furthermore, MR-CDs were used to detect Cr(VI) in tap water samples. The recoveries were between 95.8% and 98.94%, and RSDs were less than 3.17%.

Landing microextraction sediment phase onto surface enhanced Raman scattering to enhance sensitivity and selectivity for chromium speciation in food and environmental samples

The current study explores the first full mode liquid microextraction technique coupled with surface-enhanced Raman spectroscopy (SERS), and has been successfully applied for chromium speciation in food and environmental matrices. Herein, chromium as chlorochromate anion [CrO3Cl]- and the cationic rhodamine 6G [RG]+ dye has been extracted in organic phase as a complex ion associate [RG+.CrO3Cl-.nS]org at pH ≤ 1.0. Afterwards, the extracted phase was deposited on the surface of the nano-flower shaped silver nanoparticles substrate and the SERS response was monitored against the reagent blank at 1505 cm-1. Substrate characterizations, reaction mechanism assignment, stoichiometry, speciation, analytical applications, selectivity and validation were performed. The analytical procedure exhibits a detection limit of 0.03 µg L-1 under the optimized experimental conditions. The accuracy of the proposed strategy was validated by inductively coupled plasma optical emission spectrometry method using student's t- and F tests at 95% confidence.

Application of a surfactant-assisted dispersive liquid-liquid microextraction method along with central composite design for micro-volume based spectrophotometric determination of low level of Cr(VI) ions in aquatic samples

A fast, simple, low cost surfactant-assisted dispersive liquid-liquid microextraction method along with central composite design for the determination of low level of Cr(VI) ions in several aquatic samples has been developed. Initially, Cr(VI) ions present in the aqueous sample were readily reacted with 1,5‑diphenylcarbazide (DPC) in acidic medium through complexation. Sodium dodecyl sulfate (SDS), as an anionic surfactant, was then employed as an ion-pair agent to convert the cationic complex into the neutral one. Following on, the whole aqueous phase underwent a dispersive liquid-liquid microextraction (DLLME) leading to the transfer of the neutral complex into the fine droplet of organic extraction phase. A micro-volume spectrophotometer was used to determine Cr(VI) concentrations. Under the optimized conditions predicted by the statistical design, the limit of quantification (LOQ) obtained was reported to be 5.0 μg/L, and the calibration curve was linear over the concentration range of 5-100 μg/L. Finally, the method was successfully implemented for the determination of low levels of Cr(VI) ions in various real aquatic samples and the accuracies fell within the range of 83-102%, while the precision varied in the span of 1.7-5.2%.

Preparation of polymethacrylate monolith modified with cysteine for the determination of Cr(iii) ions

In this study, a simple and rapid polymer monolith microextraction procedure was developed for the determination of Cr(iii) ions by inductively coupled plasma-atomic emission spectrometry. A monolithic column modified with cysteine was synthesized and characterized by scanning electron microscopy, Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, thermal gravimetric analysis, specific surface area analysis and pore size distribution analysis. The influences of analytical parameters such as sample pH, adsorption time, eluent type, and coexisting ions were examined. The limit of detection (LOD) and limit of quantification (LOQ) for Cr(iii) ions were 0.005 μg mL-1 and 0.017 μg mL-1, and the relative standard deviation (RSD) was 7.4% (n = 5). The prepared cysteine functionalized monolithic column displayed good enrichment capacity and was successfully applied to the determination of Cr(iii) ions in real samples.

Optimization of a methodology for determination of iron concentration in aqueous samples using a newly synthesized chelating agent in dispersive liquid-liquid microextraction

The aim of this study was to establish a new dispersive liquid-liquid microextraction (DLLME) technique for the determination of iron concentration in aqueous solutions and fruit juices based on the reaction between iron and 3-hydroxy-1-(3-hydroxyphenyl)-2-methylpyridin-4(1H)-one (3-OH-PMPO) as a chelating agent. A central composite design (CCD) was applied to optimize the effects of independent parameters (pH, volume of disperser solvent and extractant solvent and chelating agent concentration) on extraction efficiency. Under the optimized conditions, the analytical curve is linear in a concentration range of 10-750 μgL^-1 with a detection limit of 5 μgL^-1. The relative standard deviation (RSD) for ten repeated determinations of iron concentrations at 40 and 200 μgL^-1 was calculated to be 4.2% and 1.2%, respectively. Relative recovery of iron in several water samples was investigated and the average was obtained in the range of 91-108%.