Poly(ethylene glycol) diacrylate as a novel chaotropic compound for design of aqueous biphasic systems

High-throughput measurement of elastic moduli of microfibers by rope coiling

There are many fields where it is of interest to measure the elastic moduli of tiny fragile fibers, such as filamentous bacteria, actin filaments, DNA, carbon nanotubes, and functional microfibers. The elastic modulus is typically deduced from a sophisticated tensile test under a microscope, but the throughput is low and limited by the time-consuming and skill-intensive sample loading/unloading. Here, we demonstrate a simple microfluidic method enabling the high-throughput measurement of the elastic moduli of microfibers by rope coiling using a localized compression, where sample loading/unloading are not needed between consecutive measurements. The rope coiling phenomenon occurs spontaneously when a microfiber flows from a small channel into a wide channel. The elastic modulus is determined by measuring either the buckling length or the coiling radius. The throughput of this method, currently 3,300 fibers per hour, is a thousand times higher than that of a tensile tester. We demonstrate the feasibility of the method by testing a nonuniform fiber with axially varying elastic modulus. We also demonstrate its capability for in situ inline measurement in a microfluidic production line. We envisage that high-throughput measurements may facilitate potential applications such as screening or sorting by mechanical properties and real-time control during production of microfibers.

Investigation of Physicochemical Properties and Surface Morphology of Hydrogel Materials Incorporating Rosehip Extract

Hydrogel materials are used in many fields of science and industry. They are of particular importance in biomedical applications. In this work, hydrogels were obtained that could act as a dressing for wounds, at the same time being a carrier of substances with antioxidant activity. The discussed materials were obtained in the field of UV radiation. The correlation between the amount of photoinitiator used and the physicochemical properties and surface morphology of the obtained materials was investigated. In addition, the hydrogels have been incorporated with wild rose extract, which is characterized by antioxidant and anti-inflammatory effects. The analysis of the sorption capacity confirmed that the obtained material is able to absorb significant amounts of incubation fluids, which, in terms of application, will enable the absorption of exudate from the wound. The highest stability of materials was noted for hydrogels obtained with the use of intermediate amounts of photoinitiator, i.e., 50 µL and 70 µL. In the case of using 20 µL or 100 µL, the photopolymerization process did not proceed properly and the obtained material was characterized by a lack of homogeneity and high brittleness. With the increase in the amount of photoinitiator, an increase in the surface roughness of hydrogel materials was confirmed. In turn, spectroscopic analysis ruled out the degradation of materials in incubation fluids, indicating the potential for their use in biomedical applications.

3D Printability Assessment of Poly(octamethylene maleate (anhydride) citrate) and Poly(ethylene glycol) Diacrylate Copolymers for Biomedical Applications

Herein, we present the first example of 3D printing with poly(octamethylene maleate (anhydride) citrate) (POMaC), a bio-adhesive material which has shown particular promise for implantable biomedical devices. The current methods to fabricate such devices made from POMaC are hindered by the imposed constraints of designing complex molds. We demonstrate the feasibility of exploiting additive manufacturing to 3D print structural functional materials consisting of POMaC. We present 3D printing of biomaterial copolymers consisting of mixtures of poly(ethylene glycol) diacrylate (PEGDA) and POMaC at different ratios. The required parameters were optimized, and characterization of the printing fidelity and physical properties was performed. We have also demonstrated that a range of mechanical properties can be achieved by tuning the POMaC/PEGDA ratio. The biocompatibility of the copolymers was ascertained via a cell viability assay. Such tunable 3D printed biomaterials consisting of POMaC and PEGDA will have significant potential application in the development of functional biomaterial tissue scaffolds and biomedical devices for the future of personalized medicine.

A hackable, multi-functional, and modular extrusion 3D printer for soft materials

Three-dimensional (3D) printing has emerged as a powerful tool for material, food, and life science research and development, where the technology’s democratization necessitates the advancement of open-source platforms. Herein, we developed a hackable, multi-functional, and modular extrusion 3D printer for soft materials, nicknamed Printer.HM. Multi-printhead modules are established based on a robotic arm for heterogeneous construct creation, where ink printability can be tuned by accessories such as heating and UV modules. Software associated with Printer.HM were designed to accept geometry inputs including computer-aided design models, coordinates, equations, and pictures, to create prints of distinct characteristics. Printer.HM could further perform versatile operations, such as liquid dispensing, non-planar printing, and pick-and-place of meso-objects. By ‘mix-and-match’ software and hardware settings, Printer.HM demonstrated printing of pH-responsive soft actuators, plant-based functional hydrogels, and organ macro-anatomical models. Integrating affordability and open design, Printer.HM is envisaged to democratize 3D printing for soft, biological, and sustainable material architectures.

Evaluation of exposure time and visible light irradiation in LCD 3D printing of ibuprofen extended release tablets

Liquid crystal display (LCD) 3D printing technology is one of the three currently available photocuring three-dimensional printing technologies. LCD 3D printers usually use wavelengths in the ultraviolent (UV) range. However, recently introduced light-emitting diodes (LED) projectors enable visible light-induced photopolymerization, which would have an advantage in terms of safety in drug production. The aim of this work was to investigate the feasibility of printing ibuprofen extended release tablets under visible light irradiation and to evaluate characteristics of printed tablets. Influences of exposure time and wavelengths (UV versus visible light) on characteristics of tablets were evaluated. Tablets were printed using 405 nm and 450 nm LED light. Visible light enabled significantly faster printing as well as better dimensions accuracy of printed tablets. It was noticed that printing under 450 nm LED resulted in slightly softer tablets compared to tablets printing with 405 nm LED. Extended ibuprofen release was obtained from all formulations. Exposure time did not have influence on drug release in formulations with low water content. However, in a formulation with higher water content, the exposure time had a pronounced effect on drug release (in eight hours of testing, differences were from 27% to 95%). Wavelength affected the release rate of ibuprofen. Tablets prepared using 450 nm LEDs released ibuprofen faster than tablets prepared with 405 nm LEDs. The main mechanism of ibuprofen release was diffusion, regardless of exposure time and wavelength. Characteristics of obtained tablets indicate that further optimization of this process is necessary, but this new printing process approach opens the possibility for novel wavelength consideration in order to obtain the safe printing process of tablets.