Removal of toxic heavy metals, phenolic compounds and textile dyes from industrial waste water using phosphonium based ionic liquids

Advances in molecularly imprinted materials for selective adsorption of phenolic pollutants from the water environment: Synthesis, applications, and improvement

The application of molecularly imprinted material (MIM) is widely employed as a material for removing phenolic pollutants from the water environment, owing to its exceptional capacity for selective adsorption and high sensitivity. In this paper, the preparation principle, bonding types, and preparation methods of MIM have been comprehensively introduced. Meanwhile, according to the binding type of MIM with phenolic pollutants, three categories of hydroxyl bonding, hydroxyl carboxyl bonding, and hydroxyl nitro bonding were carried out to explain its application to phenolic pollutants. Strategies for addressing the challenges of selective instability, high regeneration costs, and template leakage in MIM applications were summarized. These strategies encompassed the introduction of superior carriers, enhancements in preparation processes, and the utilization of molecular dynamics simulation-assisted technology. Finally, the prospects in the three aspects of material preparation, process coupling, and recycling. In summary, this paper has demonstrated the potential of utilizing MIM for the selective treatment of phenolic pollutants from the water environment.

Molecular insights into dicationic versus monocationic ionic liquids as a high hydrophobic alternative for the separation of phenol from waters

The hydrophobic nature of an extractant is particularly critical in the treatment of wastewater. Considering that dicationic ionic liquids (DILs) are likely to be more hydrophobic, a comparative study of the separation of phenol from waters using [NTf2]- based monocationic ionic liquids (MILs) and DILs is carried out both from experimental and theoretical analysis perspectives. Experimental results revealed that DILs exhibited superior extraction ability compared to MILs, with extraction efficiencies of 93.7% and 97.4% using [BMIM][NTf2] and [C6(MIM)2][NTf2]2 as extractants, respectively. The microscopic examination through theoretical calculations elucidated the higher hydrophobicity and extraction efficiency of DILs over MILs. The results indicated that the DIL showed stronger hydrophobicity than the MIL because the hydrogen bond strength between the DIL and water was lower than that of the MIL. Although the hydrogen bond strength between the DIL and phenol was lower than that of the MIL, the stronger van der Waals forces existed between DIL and phenol, so DIL was more efficient in extracting phenol. In addition, the experimental parameters were optimized to provide basic data for application, such as mass ratio of ILs to water, extraction time and temperature, pH, and initial phenol content. Finally, the DILs were recovered using rotary evaporation apparatus, and the results demonstrated that DILs had good recovery and reuse performance. In brief, this work could provide an effective method for the treatment of phenol-containing wastewater. And the revelation of molecular mechanism is expected to positively impact the design of high-performance task-specific ILs.

Decontaminating liquid-containing Cs-137 by natural Pumice stone

Radionuclides, emanating as consequential by-products of nuclear operations, are recognized as a potent source of environmentally deleterious contamination. In light of these concerns, the present investigation has employed unmodified natural pumice within a batch process to effectuate the removal of Cs-137 radionuclides from real liquid radioactive wastes (RLRWs). The discernment of optimal adsorption parameters encompassed a pH level of 5, a pumice dosage of 3.33 g/L, a mixing duration of 5 min, a mixing speed of 100 revolutions per minute, all maintained at room temperature. The attainment of a peak removal efficiency of 91.75% for Cs-137 substantiates the efficacy of the chosen conditions. Moreover, the determination of regression coefficients (R2) arising from the application of Freundlich and Langmuir isotherm analyses yielded values of 0.91 and 0.96, respectively, thus validating the appropriateness of both models in depicting the adsorption mechanism. Evidently, the pseudo-second-order kinetic model exhibited a high correlation coefficient of 0.99, attesting to its aptitude in characterizing the adsorption dynamics. A thermodynamic appraisal of the process indicated an endothermic nature, offering insights into the fundamental energetics governing the interaction. Consequently, the adsorption phenomenon unfolded predominantly on monolayer, heterogeneous surfaces, with chemical interactions taking precedence on the active pumice sites.

Optimizing the method for removing MSNs templates using an ionic liquid ([C4mim]Cl)

The key step in preparing mesoporous silica is to remove the organic template agent, and the most common method used to achieve this goal is high-temperature calcination. However, this method has many disadvantages, one of which is that it reduces the silanol density on the surface of mesoporous silica, which affects its subsequent modification. Ionic liquids (ILs) are often used as extractants. In this work, the 1-butyl-3-methylimidazolium chloride ([C4mim]Cl) IL is considered, and the effects of its concentration, reaction temperature, and reaction time as well as HCl concentration on the extraction rate and silanol density were investigated using an IL extraction template agent (cetyl trimethyl ammonium bromide (CTAB)). The results show that an IL concentration of 10%, a reaction temperature of 120 °C, a reaction time of 12 h, and an HCl concentration of 1% are the best reaction parameters; with these parameters, the extraction rate and the silanol density were found to be 93.19% and 2.23%, respectively. The silanol density of mesoporous silica treated by calcination is only 0.81%. A higher silanol density provides more reaction sites, so that the modified mesoporous silica treated with the IL can be loaded with more Zn ions.

Solidification/stabilisation behaviours of Zn2+ in magnesium potassium phosphate cement: Experiments and density functional theory study

The solidification/stabilisation behaviours of Zn2+ in magnesium potassium phosphate cement (MKPC) have not been thoroughly investigated. Herein, a series of experiments and a detailed density functional theory (DFT) study were conducted to investigate the solidification/stabilisation behaviours of Zn2+ in MKPC. The results showed that the compressive strength of MKPC reduced with the addition of Zn2+ because the formation of MgKPO4·6H2O (the main hydration product in MKPC) was delayed with the addition of Zn2+, as discovered by the crystal characteristics, and because Zn2+ exhibited a lower binding energy in MgKPO4·6H2O compared to Mg2+, as revealed by DFT results. Additonally, Zn2+ had little influence on the structure of MgKPO4·6H2O, and Zn2+ existed in MKPC as the formation of Zn2(OH)PO4, which was decomposed in the range of around 190-350 °C. Moreover, there were a lot of well-crystallised tabular hydration products before the addition of Zn2+, but the matrix was comprised of irregular prism crystals after adding Zn2+. Furthermore, the leaching toxicity of Zn2+ of MKPC was much smaller than the requirements of Chinese and European standards.

Photocatalytic Activity of the Oxidation Stabilized Ti3 C2 Tx MXene in Decomposing Methylene Blue, Bromocresol Green and Commercial Textile Dye

Two-dimensional MXenes are excellent photocatalysts. However, their low oxidation stability makes controlling photocatalytic processes challenging. For the first time, this work elucidates the influence of the oxidation stabilization of model 2D Ti3 C2 Tx MXene on its optical and photocatalytic properties. The delaminated MXene is synthesized via two well-established approaches: hydrofluoric acid/tetramethylammonium hydroxide (TMAOH-MXene) and minimum intensive layer delamination with hydrochloric acid/lithium fluoride (MILD-MXene) and then stabilized by L-ascorbic acid. Both MXenes at a minimal concentration of 32 mg L-1 show almost 100% effectiveness in the 180-min photocatalytic decomposition of 25 mg L-1 model methylene blue and bromocresol green dyes. Industrial viability is achieved by decomposing a commercial textile dye having 100 times higher concentration than that of model dyes. In such conditions, MILD-MXene is the most efficient due to less wide optical band gap than TMAOH-MXene. The MILD-MXene required only few seconds of UV light, simulated white light, or 500 nm (cyan) light irradiation to fully decompose the dye. The photocatalytic mechanism of action is associated with the interplay between surface dye adsorption and the reactive oxygen species generated by MXene under light irradiation. Importantly, both MXenes are successfully reused and retained approximately 70% of their activity.

Separation of Anionic Chlorinated Dyes from Polluted Aqueous Streams Using Ionic Liquids and Their Subsequent Recycling

The effect of ionic liquids on the separation of chlorinated anionic dyes such as Mordant Blue 9 (MB9) or Acid Yellow 17 (AY17) via ion exchange has been investigated in model aqueous solutions that simulate wastewater from the textile dyeing industry. The effect of ionic liquids chemical nature on the separation efficiency of mentioned dyes has been compared. It was found that especially ionic liquid based on quaternary ammonium salts comprising two or three long alkyl chains bound to the quaternary ammonium nitrogen (typically benzalkonium chloride or Aliquat 336) are very effective for the separation of both studied MB9 and AY17 from aqueous solution. In addition, the innovative technique has been developed for the reactivation of spent ionic liquids which is based on the chemical reduction of the formed ion pairs using NaBH4/NiSO4, NaBH4/Na2S2O5 or Raney Al-Ni alloy/NaOH. Thus, only NaBH4/NiSO4 in co-action with Al-Ni alloy enables both effective reduction of the azo bond and subsequent hydrodechlorination of emerging chlorinated aromatic amines. The efficiency of tested dyes separation or regeneration of ion pairs was evaluated by determination of the absorbance at wavelength of the maximum absorbance, of the Chemical Oxidation Demand (COD), and of the Adsorbables Organically bound Halogens (AOX). The formation of ion pairs or products of reduction and hydrodechlorination of these ion pairs has been studied using the 1H NMR and LC-MS techniques.

Hydrophobic ammonium based ionic liquids for efficient extraction of textile dyes from aqueous media: Extraction study and antibacterial evaluation

Alizarin red S (ARS) extraction from aqueous medium was carried out using hydrophobic ionic liquids (ILs) containing trioctylammonium cation paired with 4-tert-butylbenzoate ([TOA][Butbenz] (IL1), 4-phenylbutanoate ([TOA][PheBut] (IL2), 3-4-dimethylbenzoate ([TOA][DMbenz] (IL3), naphthoate, ([TOA][Naph]) (IL4), salicylate ([TOA][Sali]) (IL5) and nonanedioate ([TOA]2[Nona]) (IL6). The findings demonstrated that all of the tested ILs were efficient for extracting ARS, however, [TOA]2[Nona] was more effective than others. For the extraction of ARS from the aqueous phase, the effects of various parameters including the initial pH of the dye solution, contact time, ILs to dye volume ratio (VIL:VW), dye concentration, temperature, and salt effect were investigated. The spontaneity of the liquid-liquid extraction of ARS from the aqueous phase to the IL phase was confirmed by thermodynamic parameters. More than 90% of the ARS was extracted from the aqueous phase to the IL phase throughout all experiments. Interaction of selected IL with dyes were confirmed using FTIR analysis. The standard bacterial strains of Escherichia coli (E. coli) ATCC BAA-2471 (gram negative) and Methicillin-resistant Staphylococcus (MRSA) ATCC 43300 (gram positive) were used for evaluating antibacterial activity. The lower dose (250 ppm), the ILs1, 2, 3, 4, 5, and 6 inhibited 0.40, 1.50, 6.50, 1.50, 2.50, and 0.50 mm growth of E. coli, and 4.0, 2.0, 16.50, 0.40, 5.0, and 3.50 mm growth of MRSA, respectively. The experimental findings confirmed that the present ILs can be utilized as an effective solvent for ARS and other dyes extraction from aqueous media.

A Critical Review of Snail Shell Material Modification for Applications in Wastewater Treatment

Sea material is becoming increasingly popular and widely used as an adsorbent in wastewater treatment. Snail shell, a low-cost and natural animal waste material, has been shown to have a high calcium content (>99%) and a large potential surface area for the development of sustainable adsorbents. This paper presents a novel synthesis of methods for using snail shell absorbent materials in the treatment of wastewater containing heavy metals, textile dyes, and other organic substances. Modified biochar made from snail shells has gained popularity in recent years due to its numerous benefits. This paper discusses and analyzes modification methods, including impregnating with supplements, combining other adsorbents, synthesis of hydroxyapatite, co-precipitation, and the sol-gel method. The analysis of factors influencing adsorption efficiency revealed that pH, contact time, temperature, initial concentration, and adsorbent dose all have a significant impact on the adsorption process. Future research directions are also discussed in this paper as a result of presenting challenges for current snail adsorbents.

A novel PES-C/(GO-COOH/Ce) blended membrane for treating heavy-metal-ion wastewater

A GO-COOH/Ce complex was introduced into a phenolphthalide polythersulfone (PES-C) matrix to prepare a PES-C/(GO-COOH/Ce) blended membrane by nonsolvent-induced phase transformation (NIPS). FT-IR and EDS analysis confirmed that the GO-COOH/Ce complex was successfully incorporated into the PES-C matrix. SEM showed that the blended membrane possessed an asymmetric structure with finger-like pores. The best comprehensive performance was obtained for a PES-C/(GO-COOH/Ce) blended membrane prepared using 0.1 wt.% of the GO-COOH/Ce complex in the casting liquid. The specific results for the blended membrane were as follows: the fluxes of pure water and 0.1 g/L lead nitrate solution were 272 L/m2·h and 214 L/m2·h, respectively; the rejection of bovine serum albumin (BSA) was 99.4%; the rejection of lead ions was 96.2%; the moisture content was 10.9%; the contact angle was 67.1°; the Young's modulus was 35.7 MPa; and the flux recovery ratio was 1.5 times higher than that of the pure PES-C membrane. The antibacterial-zone diameters of the PES-C/(GO-COOH/Ce) blended membrane used against Escherichia coli and Staphylococcus aureus were 2.50 cm and 2.88 cm, respectively. A catalytic cleaning test showed a flux recovery ratio of 63% after washing the PES-C/(GO-COOH/Ce) blended membrane with a 0.2 g/L acetic acid solution for 0.5 h.

Removal of Zn(II) by magnetic composite adsorbent: synthesis, performance, and mechanism

In this study, L-methionine and nano-Fe₃O₄ were encapsulated and cured on sodium alginate by the ionic cross-linking method to form magnetic composite gel spheres (SML) as an adsorbent for the removal of Zn(II) from water. The influence of adsorbent dosages, pH, reaction time, and initial ion concentration on the ability of the gel spheres to adsorb Zn(II) was investigated, and the adsorption mechanism was identified. The experimental results showed that under the optimum conditions (pH = 5, t = 60 min, dosage of SML is 0.7 g·L^-1), the maximum amount of Zn(II) adsorbed by the adsorbent gel spheres reached 86.84 mgˑg^-1. The reaction process of this adsorbent fits well with the Langmuir and pseudo-second-order kinetic models and is a heat absorption reaction. The adsorbent would preferentially adsorb Pb(II), and the adsorption efficiency of Zn(II) decreased when the concentration of interfering ions increased in the coexistence system. Further mechanistic research showed that this magnetic composite adsorbent is a mesoporous material with superior adsorption performance, and the amino and carboxyl groups on it react with Zn(II) via ligand chelation; the ion exchange effect of Ca(II) also plays a role. The adsorption amount of Zn(II) was maintained at a higher level after 5 cycles, and the loss of Fe was approximately 0.2%. In summary, SML, which is environmentally friendly, efficient, and recyclable, is an ideal adsorbent for Zn(II) removal.

Simultaneous Removal of Cu2+, Cd2+ and Pb2+ by Modified Wheat Straw Biochar from Aqueous Solution: Preparation, Characterization and Adsorption Mechanism

As an eco-friendly and efficient adsorbent for removal of potential toxic metals from aqueous solution, biochar has received widespread attention. In the present study, wheat straw biochar (BC) and corresponding modified biochar (HNC) were used to remove Cu²⁺, Cd²⁺ and Pb²⁺ from an aqueous solution. The influence of the environment factors on metals adsorption and adsorption mechanism were discussed in detail. The results showed that the HNC had porous structures and owned ample functional groups (-OH, -COOH and C-N groups) compared with the BC. In the single system, the adsorption capacities of HNC for Cu²⁺, Cd²⁺ and Pb²⁺ at a pH of 5.5 were 18.36, 22.83 and 49.38 mg/g, which were 76.89%, 164.36% and 22.75% higher than that of the BC, respectively. In addition, the adsorption process of Cu²⁺ and Cd²⁺ on BC and HNC fitted to the Langmuir isotherm model and pseudo-second-order kinetics, but the adsorption of Pb²⁺ on BC and HNC fitted to the Langmuir isotherm model and pseudo-first-order kinetics. Adsorption isotherms indicated that the adsorption of Cu²⁺, Cd²⁺ and Pb²⁺ by BC and HNC was a spontaneous endothermic process. The competitive adsorption of mixed metal ions (Cu²⁺, Cd²⁺ and Pb²⁺) revealed that HNC was more preferential to adsorb Cu²⁺ compared with Cd²⁺ and Pb²⁺. Furthermore, Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy analyses revealed that the main adsorption mechanisms were surface complexation and precipitation, and the adsorbed Cu²⁺, Cd²⁺ and Pb²⁺ on HNC mainly exist as CuO, Cd(OH)₂, Pb₃O₄ and Pb(OH)₂.

Amine-Based Deep Eutectic Solvents for Alizarin Extraction from Aqueous Media

Alizarin dye is toxic and has a negative influence on human life and the environment. Consequently, the scientific community faces a difficult issue in developing efficient approaches for removing alizarin from water streams. Six distinct deep eutectic solvents (DESs) containing different hydrogen bond acceptors (HBAs), namely trioctylphosphine, trioctylamine and trihexylamine, and two hydrogen bond donors (HBDs), namely salicylic acid and malonic acid, were used to rapidly remove alizarin from high concentration solutions up to 2000 mg/L at room temperature using the liquid–liquid micro-extraction method (LLE). DES-3 had the highest extraction efficiency for alizarin among the other synthesized DESs. The effect of process variables such pH, contact time, dye initial concentration, volume ratio, temperature and salt on alizarin extraction efficiency from water stream was explored, optimized and reported. Statistical analysis was conducted to ensure the accuracy of values for the optimized parameters. For a 1000 mg/L solution of alizarin with a DES/alizarin volume ratio of 1:10 at room temperature, the maximum elimination of 98.02 percent was achieved in 5 min. FTIR was used to analyze the structural properties of DES and the interaction between DES and alizarin. The thermal stability of DES-3 was determined using thermogravimetric analysis (TGA) and indicated that DES-3 has excellent thermal stability up to 320 °C. Human saline was used to test the toxicity of the synthesized DES in vitro. It was determined that synthesized DES is less harmful and more effective at removing alizarin.

Modeling and Optimization of Heavy Metals Biosorption by Low-Cost Sorbents Using Response Surface Methodology

This paper exploits, through modeling and optimization, the experimental laboratory data on the biosorption of heavy metal ions Pb(II), Cd(II), and Zn(II) from aqueous media using soybean and soybean waste biomasses. The biosorption modeling was performed using the Response Surface Methodology, followed by optimization based on numerical methods. The aim of the modeling was to establish the most probable mathematical relationship between the dependent variables (the biosorption efficiency of the biosorbents when adsorbing metal ions, R(%), and the biosorption capacity of sorbents, q(mg/g)) and the process parameters (pH; sorbent dose, DS (g/L); initial metal ion concentration in solution, c0 (mg/L); contact time, tc (min); temperature, T (°C)), validated by methodologies specific to the multiple regression analysis. Afterward, sets of solutions were obtained through optimization that correlate various values of the process parameters to maximize the objective function. These solutions also confirmed the performance of soybean waste biomass in the removal of heavy metal ions from polluted aqueous effluents. The results were validated experimentally.

Engineered Magnetic Carbon-Based Adsorbents for the Removal of Water Priority Pollutants: An Overview

This review covers the preparation, characterization, and application of magnetic adsorbents obtained from carbon-based sources and their application in the adsorption of both inorganic and organic pollutants from water. Different preparation routes to obtain magnetic adsorbents from activated carbon, biochar, hydrochar, graphene, carbon dots, carbon nanotubes, and carbon nanocages, including the magnetic phase incorporated on the solid surface, are described and discussed. The performance of these adsorbents is analyzed for the removal of fluoride, arsenic, heavy metals, dyes, pesticides, pharmaceuticals, and other emerging and relevant water pollutants. Properties of these adsorbents and the corresponding adsorption mechanisms have been included in this review. Overall, this type of magnetic adsorbents offers an alternative for facing the operational problems associated to adsorption process in water treatment. However, some gaps have been identified in the proper physicochemical characterization of these adsorbents, the development of green and low-cost preparation methods for their industrial production and commercialization, the regeneration and final disposal of spent adsorbents, and their application in the multicomponent adsorption of water pollutants.

Enhanced Adsorption of Rhodamine B on Modified Oil-Based Drill Cutting Ash: Characterization, Adsorption Kinetics, and Adsorption Isotherm

In this paper, phosphoric acid (H₃PO₄), hydrochloric acid (HCl), and hydrogen peroxide (H₂O₂) were employed for the modification of oil-based drill cutting ash (OBDCA) for the first time. The adsorption of rhodamine B (RhB) on modified oil-based drill cutting ash (MOBDCA) in an aqueous medium was investigated. H₂O₂-modified OBDCA had the optimal adsorption efficiency for RhB. The physical and chemical properties of MOBDCA were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), ζ-potential, N₂ adsorption-desorption isotherm, and pore size distribution. The effect of the pH value (3-11), reaction time (10-720 min), and initial RhB concentration (10-200 mg/L) on RhB adsorption was discussed. The adsorption kinetics highly fitted with the pseudo-second-order model (R ² > 0.99), which indicated that the adsorption process was dominated by chemisorption. The adsorption isotherm fitted well with the Langmuir and Freundlich models (R ² > 0.97), which indicated the monolayer adsorption process and the heterogeneous adsorption process, respectively. The theoretic adsorption capacity (50 mg/g) for RhB was achieved by H₂O₂-modified OBDCA. This paper provides a promising method of resource utilization of OBDCA to treat organic pollutants.