Adsorption of 3-aminophenol and resorcinol on avocado seed activated carbon: Mathematical modelling, thermodynamic study and description of adsorbent performance

Adsorptive features of cyclohexane carboxylic naphthenic acid on a novel cross-linked polymer developed from spent coffee grounds

Naphthenic acids (NA) are organic compounds commonly found in crude oil and produced water, known for their recalcitrance and toxicity. This study introduces a new adsorbent, a polymer derived from spent coffee grounds (SCGs), through a straightforward cross-linking method for removing cyclohexane carboxylic acid as representative NA. The adsorption kinetics followed a pseudo-second-order model for the data (0.007 g min-1 mg-1), while the equilibrium data fitted the Sips model ( q m = 140.55 mg g-1). The process's thermodynamics indicated that the target NA's adsorption was spontaneous and exothermic. The localized sterical and energetic aspects were investigated through statistical physical modeling, which corroborated that the adsorption occurred indeed in monolayer, as suggested by the Sips model, but revealed the contribution of two energies per site (n 1 ; n 2 ). The number of molecules adsorbed per site ( n ) was highly influenced by the temperature as n 1 decreased with increasing temperature and n 2 increased. These results were experimentally demonstrated within the pH range between 4 and 6, where both C6H11COO-(aq.) and C6H11COOH(aq.) species coexisted and were adsorbed by different energy sites. The polymer produced was naturally porous and amorphous, with a low surface area of 20 to 30 m2 g-1 that presented more energetically accessible sites than other adsorbents with much higher surface areas. Thus, this study shows that the relation between surface area and high adsorption efficiency depends on the compatibility between the energetic states of the receptor sites, the speciation of the adsorbate molecules, and the temperature range studied.

Adsorption of perfluorooctanoic carboxylic and heptadecafluorooctane sulfonic acids via magnetic chitosan: isotherms and modeling

This paper evaluates the adsorption mechanism of perfluorooctanoic carboxylic acid (PFCA) and heptadecafluorooctane sulfonic acid (HFOSA) on magnetic chitosan for the first time via a statistical physics modeling. Magnetic chitosan (MC-CoFe2O4) was produced from shrimp wastes and used in standard batch adsorption systems to remove PFCA and HFOSA. The experimental isotherms indicated that the maximum adsorption capacities ranged from 14 to 27.12 mg/g and from 19.16 to 45.12 mg/g for PFCA and HFOSA, respectively, where an exothermic behavior was observed for both compounds. The adsorption data were studied via an advanced model hypothesizing that a multilayer process occurred for these adsorption systems. This theoretical approach indicated that the total number of formed layers of PFCA and HFOSA adsorbates is about 3 (Nt = 2.83) at high temperatures (328 K) where a molecular aggregation process was noted during the adsorption. The maximum saturation-multilayer adsorption of PFCA and HFOSA on magnetic chitosan was 30.77 and 50.26 mg/g, respectively, and the corresponding adsorption mechanisms were successfully investigated. Two energies were responsible for the formed adsorbate layer directly on the surface and the vertical layers were computed and interpreted, reflecting that physical interactions were involved to bind these molecules on the adsorbent surface at different temperatures where the calculated adsorption energies ranged from 14 to 31 kJ/mol. Overall, this work provides theoretical insights to understand the adsorption mechanism of PFCA and HFOSA using the statistical physics modeling and its results can be used to improve the adsorbent performance for engineering applications.

Composite of methyl polysiloxane and avocado biochar as adsorbent for removal of ciprofloxacin from waters

Two carbon composite materials were prepared by mixing avocado biochar and methyl polysiloxane (MK). Firstly, MK was dissolved in ethanol, and then the biochar was added at different times. In sample 1 (R1), the time of adding biochar was immediately after dissolving MK in ethanol, and in sample 2 (R₂), after 48 h of MK dissolved in ethanol. The samples were characterized by nitrogen adsorption/desorption measurements obtaining specific surface areas (S_BET) of 115 m2 g^-1 (R₁) and 580 m2 g^-1 (R₂). The adsorbents were further characterized using scanning electron microscopy, FTIR and Raman spectroscopy, adsorption of vapors of n-heptane and water, thermal analysis, Bohem titration, pHpzc, and C H N elemental analysis. R₁ and R₂ adsorbents were employed as adsorbents to remove the antibiotic ciprofloxacin from the waters. The t_1/2 and t_0.95 based on the interpolation of Avrami fractional-order were 20.52 and 246.4 min (R₁) and 14.00 and 157.6 min (R₂), respectively. Maximum adsorption capacities (Q_max) based on the Liu isotherm were 10.77 (R₁) and 63.80 mg g^-1 (R₂) for ciprofloxacin. The thermodynamic studies showed a spontaneous and exothermic process for both samples, and the value of ΔH° is compatible with physical adsorption.

Study on removal of copper ions from aqueous phase by modified sepiolite flocs method

With the improvement of environmental protection and standards, the recovery and recycling of copper ions released from industrial wastewater discharge has aroused sufficient research interest. A new adsorbent (ABsep) derived from natural sepiolite (Sep) by modification technology of hexadecyltrimethoxysilane (HDTMS) or tetraethylorthosilicate (TEOS) and flocs separation method for adsorption of Cu²⁺ in wastewater have been investigated in this paper. The changes of crystal structure and physicochemical properties of Sep during modification process showed that HDTMS and TEOS were loaded onto the Sep surface without inserting into the Sep interlayer structure. The adsorption experimental results presented a smaller amount of ABsep (1 g/L) achieved 97.5% removal of 50 mg/L Cu²⁺ at pH 6 and temperature of 298 K within a shorter contact time (50 min). It is interesting the adsorption process of Cu²⁺ on ABsep was spontaneous and exothermic, with physical adsorption dominating, as result of combination of physical adsorption, electrostatic gravitational force, and chemical reaction. Because of good physical-chemical adsorption performance of ABsep surface to Cu²⁺, high removal rates of Cu²⁺ from aqueous phase could be achieved after three adsorption regeneration cycles, this indicated the ABsep was expected to be a promising adsorbent of Cu²⁺ removal for wastewater treatment.

A review of avocado waste-derived adsorbents: Characterizations, adsorption characteristics, and surface mechanism

Avocado is one of the most important fruits with a high nutritional content; this fruit is consumed and cultivated worldwide. It is originally grown in Central America and the West Indies islands. But it is now cultivated in the tropical and subtropical regions of the world. Avocado waste is an abundantly available raw material that can be converted into adsorbents to remove different pollutants from aqueous solutions. This review article explores the utilization of avocado waste as raw material to develop an efficient adsorbent and its use against various toxicants. Many research papers have been published on the use of avocado waste-derived adsorbents in the recent past. The factors that affect the adsorption processes are examined in light of published references. Some critical adsorption parameters, such as equilibrium (isotherms), kinetics, and thermodynamics, have been reported in the published literature; these parameters and their data are critically discussed. The characterization, mechanism, and surface chemistry of avocado waste-derived adsorbents are also discussed. To date, no review article on avocado waste-derived adsorbents is available, where researchers can get an overview of the preparation, characterization, and adsorption attributes of avocado waste adsorbents against various pollutants. Recent literature demonstrates the effective utilization of avocado waste as a cleaner and sustainable raw material for the production of adsorbents.