Synthesis of amine-modified graphene integrated membrane as protocols for simultaneous rejection of hydrocarbons, metal ions, and salts from water

Distribution and removal pathways of heavy metals during the operation of sludge treatment wetlands

ABSTRACTThe distribution and removal pathways of heavy metals within different sludge treatment wetlands (STWs) during different running periods in Northeast China have not been well studied. In this study, we examined three STWs, i.e. an STW with aeration tubes only (unit 1; U1), an STW with reeds and aeration tubes (unit 2; U2), and an STW with reeds only (unit 3; U3). The results showed that the levels of Cu as well as Zn accumulated faster within STW residual sludge, whereas the levels of Cd, Cr, Ni, and Pb accumulated more slowly and decreased slightly over time. The removal rates of heavy metals from the influent sludge by STWs ranged from 64.5% (Cr) to 92.2% (Zn). Reeds removed heavy metals from the STWs by direct absorption, and Zn was highly enriched in the reeds. The presence of reeds also promoted the spreading of heavy metals to the substrate layer and improved the removal of heavy metals in STWs. The mass of each heavy metal accumulated within the residual sludge of U2 and U3 was lower than that of U1, indicating that reeds could facilitate the removal of heavy metals. The STWs removed heavy metal mainly by substrate adsorption, and the mass percentage of heavy metals accumulated in the substrate ranged from 35.8 to 63.6%.

Graphene-based nanomaterials as potential candidates for environmental mitigation of pesticides

Over the years, bioaccumulation of hazardous chemicals in the food chain has become a critical issue, resulting in numerous health risks. Environmental mitigation aims to clean up contaminated sites and eliminate hazardous materials from the air, water, or soil to restore the site to its original and safe condition. Pesticides constitute one of the most dangerous environmental pollutants which are generally used to increase crop production. Addressing the removal or treatment of pesticides has become pivotal in mitigating environmental threats. Diverse remediation methods are employed to protect the environment and public health. Graphene-based materials have emerged as promising candidates with exceptional properties, including excellent adsorption capacity due to their high surface area, strong hydrophilicity, and tunable properties. Owing to these properties, they have been attracting major research attention in the field of design and fabrication of materials for the mitigation of pesticides from the environment such as from contaminated food, water and other samples. Various physical, chemical and biological extraction techniques are adopted to remove pesticides. This review article provides an insight into the potential role of graphene-based materials in the environmental remediation of pesticides. We have focused on the removal of Organophosphates, Organochlorines, Carbamates and Pyrethroids present in water, fruit, vegetable and other samples, highlighting the urgent need for environmental remediation. While graphene-based materials hold potential for pesticide remediation, addressing challenges in scalable production, assessing long-term sustainability, and mitigating potential environmental impacts are critical steps for successful large-scale applications.

Assessing the ecological impacts of polycyclic aromatic hydrocarbons petroleum pollutants using a network toxicity model

Polycyclic aromatic hydrocarbons (PAHs) are significant petroleum pollutants that have long-term impacts on human health and ecosystems. However, assessing their toxicity presents challenges due to factors such as cost, time, and the need for comprehensive multi-component analysis methods. In this study, we utilized network toxicity models, enrichment analysis, and molecular docking to analyze the toxicity mechanisms of PAHs at different levels: compounds, target genes, pathways, and species. Additionally, we used the maximum acceptable concentration (MAC) value and risk quotient (RQ) as an indicator for the potential ecological risk assessment of PAHs. The results showed that higher molecular weight PAHs had increased lipophilicity and higher toxicity. Benzo[a]pyrene and Fluoranthene were identified as core compounds, which increased the risk of cancer by affecting core target genes such as CCND1 in the human body, thereby influencing signal transduction and the immune system. In terms of biological species, PAHs had a greater toxic impact on aquatic organisms compared to terrestrial organisms. High molecular weight PAHs had lower effective concentrations on biological species, and the ecological risk was higher in the Yellow River Delta region. This research highlights the potential application of network toxicity models in understanding the toxicity mechanisms and species toxicity of PAHs and provides valuable insights for monitoring, prevention, and ecological risk assessment of these pollutants.

A comprehensive study on applications of nanomaterials in petroleum upstream and downstream industry

Nanotechnology has emerged as a revolutionary technology that has been applied in the oil and gas industry for over a decade, spanning the upstream, midstream, and downstream sectors. Nanotechnology has made significant contributions to the exploration of crude oil and natural gas, both in underground and deep-water environments. It has also played a crucial role in improving the drilling process, enabling the extraction of oil and gas resources from beneath the Earth's surface. Nanoparticles, with their unique physical and chemical properties, such as high specific surface area, high pore volume, and small size, have demonstrated considerable potential in the oil industry. Extensive research has been conducted to explore various types of nanoparticles for advanced applications, including oil exploration, drilling, production, and enhanced oil recovery (EOR). Moreover, nanomaterials have found applications in downstream and intermediate sectors, such as crude oil refining, natural gas processing, and transportation and storage of petroleum products. Ongoing advancements in nanomaterial synthesis methods, the exploration of new nanomaterial uses, and understanding the remarkable properties of nanomaterials will continue to make them increasingly valuable in the oil and gas sector. The oil and gas industry recognises the potential of nanotechnology and nanoparticles and is investing significantly in research and development in this area. This comprehensive review aims to summarise successful applications of nanotechnology while addressing associated challenges. It serves as a valuable resource for future research and application endeavours in the field, highlighting the potential of nanotechnology in the oil and gas industry.

Green synthesis of sustainable magnetic nanoparticles Fe3O4 and Fe3O4-chitosan derived from Prosopis farcta biomass extract and their performance in the sorption of lead(II)

The sustainable processes are now in tremendous demand for nanomaterial synthesis as a result of their unique properties and characteristics. The magnetic nanoparticles comprised of Fe3O4 and its conjugate with abundant and renewable biopolymer, chitosan, were synthesized using Prosopis farcta biomass extract, and the resulting materials were used to adsorb Pb (II) from aqueous solution. Thermodynamic parameters revealed that the sorption of lead (II) on Fe3O4 as well as Fe3O4-Chitosan (Fe3O4-CS) has been an endothermic and self-regulating procedure wherein the sorption kinetics was defined by a pseudo-second-order pattern and the sorption isotherms corresponded to the Freundlich pattern. A multivariable quadratic technique for adsorption process optimization was implemented to optimize the lead (II) adsorption on Fe3O4 and Fe3O4-chitosan nanoparticles, the optimal conditions being pH 7.9, contact time of 31.2 min, initial lead concentration of 39.2 mg/L, adsorbent amount of 444.3 mg, at a 49.7 °C temperature. The maximum adsorption efficiencies under optimal conditions were found to be 69.02 and 89.54 % for Fe3O4 and Fe3O4-CS adsorbents, respectively. Notably, Fe3O4 and Fe3O4-CS can be easily recovered using an external magnet, indicating that they are a viable and cost-effective lead removal option.

Functionalized Carbon Nanotubes Encapsulated Alginate Beads for the Removal of Mercury Ions: Design, Synthesis, Density Functional Theory Calculation, and Demonstration in a Batch and Fixed-Bed Process

Various nanomaterials have been envisaged mainly through batch studies for environmental remediation application. The real utilization of these new generation adsorbents in large scale pose a difficulty due to its low density and small size which makes it difficult for isolation after application. In this context, nanoadsorbents polymer composite beads can be seen as a way out. Here, functionalized CNTs (carbon nanotubes) have been fabricated into micro beads with sodium alginate. The alginate-functionalized CNT (Alg-f-CNT) beads were then comprehensively evaluated for batch and fixed-bed column separation of divalent mercury ions from an aqueous medium. The effects of process parameters such as pH, contact time, feed Hg2+ concentration, and temperature were studied. Simulation of the experimental data suggested that adsorption is an endothermic spontaneous process which follows the pseudo-second-order kinetic and Langmuir isotherm model. The desorption of the Hg2+ ion from used adsorbent was possible with 1 M HNO3. The breakthrough curves at different process parameters were investigated during fixed-bed column separation and found to be in good agreement with Thomas model. The regeneration and reusability of the adsorbent were tested up to five cycles without a significant decrease in the removal performance. Density functional theory studies revealed stronger interaction of Alg-f-CNT with Hg compared to free alginic acid and established the role of carboxyl and oxo groups present in the adsorbent in the coordination of the Hg2+ ions. The experimental results demonstrate that functionalized CNT-encapsulated alginate beads are a promising alternate material, which can be used to remove mercury in the fixed-bed column mode of the operation.

A novel, efficient and economical alternative for the removal of toxic organic, inorganic and pathogenic water pollutants using GO-modified PU granular composite

Multicomponent wastewater treatment utilising simple and cost-effective materials and methods is an important research topic. This study has reported the fabrication and utilisation of graphene oxide (GO) embedded granular Polyurethane (PU) (GOPU) adsorbent for the treatment of lead ion (Lead ion (Pb(II)), Methylene blue (MB), and E. coli. PU granules were wrapped with GO flakes to improve hydrophilicity, interaction with polluted water, cation-exchange reaction, and binding of pollutants on its surface. Synthesised GOPU granules were characterised by X-Ray Diffraction (XRD), Raman, Fourier transform infrared (FTIR) spectroscopy, and Scanning electron microscopy (SEM) analysis to ensure the successful synthesis of GO and fabrication of GOPU granules. Further, batch and continuous adsorption processes were studied in different operating conditions to evaluate the performance of GOPU granules in practical applications. The kinetic and isotherm analyses revealed that the adsorption of Lead (Pb(II)) ion and Methylene Blue (MB) dye followed the Freundlich and Langmuir isotherm models, respectively, and they showed good agreement with the Pseudo-second-order kinetic model. The adsorption capacities of GOPU granules for the elimination of Pb(II) and MB dye were about 842 mg/g and 899 mg/g, respectively. Additionally, investigations into the fixed bed column revealed that the adsorption column performed best at a flow rate of 5 mL/min and a bed height of 6 cm. Pb(II) adsorption had a bed uptake capacity (q_bed) of 88 mg/g and percentage removal efficiency (%R) of 76%. Similarly, MB adsorption had a bed uptake capacity of 202 mg/g and a percentage removal efficiency of 71%. A systematic invention on antibacterial activity toward E. coli showed that The GOPU granules have a removal efficiency of about 100% at an exposure of 24 h. These findings indicated the possible use of GOPU granules as promising adsorbents for various water pollutants.

Synchronously Enhanced Removal Ability and Stability of MXene through Biomimetic Modification

Increasing environmental problems intensify the demand for high-performance environmental purification materials. MXene is a typical transition-metal carbide/nitride material with a two-dimensional geometric feature and a good deal of functional groups, and it is considered as an efficient adsorbent for removing pollutants from wastewater. However, the easy oxidation and relatively low adsorption capacity greatly restrict its application. In this study, the MXene/polydopamine (PDA) composite particles were fabricated through the biomimetic modification method of inducing the self-polymerization of dopamine in an MXene aqueous solution. Microstructure characterizations demonstrate that PDA facilitates the exfoliation of MXene. Adsorption measurements show that MXene and PDA exhibit an apparent synergistic effect in removing chromium hexavalent Cr(VI) from aqueous solution, and more PDA content leads to a larger synergistic effect. Consequently, the composite particles exhibit an ultrahigh adsorption capacity (862.3 mg/g). Specifically, even if the composite particles were stored in aqueous solution for 2 months, they still exhibit high adsorption ability with only a 3.3% loss in adsorption capacity, indirectly confirming the enhanced stability of MXene induced by PDA. Furthermore, the composite particles also show reduction ability to Cr(VI) and about 54.3% Cr(VI) can be reduced to harmless chromium trivalent Cr(III). This study provides a new method for the preparation of MXene-based adsorbents with excellent adsorption capacity and high stability, which has broad application prospects in the field of wastewater treatment.

A critical review on adsorptive removal of antimony from waters: Adsorbent species, interface behavior and interaction mechanism

Antimony (Sb) has raised widespread concern because of its negative effects on ecology and human health. The extensive use of antimony-containing products and corresponding Sb mining activities have discharged considerable amounts of anthropogenic Sb into the environment, especially the water environment. Adsorption has been employed as the most effective strategy for Sb sequestration from water; thus, a comprehensive understanding of the adsorption performance, behavior and mechanisms of adsorbents benefits to develop the optimal adsorbent to remove Sb and even drive its practical application. This review presents a holistic analysis of adsorbent species with the ability to remove Sb from water, with a special emphasis on the Sb adsorption behavior of various adsorption materials and their Sb-adsorbent interaction mechanisms. Herein, we summarize research results based on the characteristic properties and Sb affinities of reported adsorbents. Various interactions, including electrostatic interactions, ion exchange, complexation and redox reactions, are fully reviewed. Relevant environmental factors and adsorption models are also discussed to clarify the relevant adsorption processes. Overall, iron-based adsorbents and corresponding composite adsorbents show relatively excellent Sb adsorption performance and have received widespread attention. Sb removal mainly depends on chemical properties of the adsorbent and Sb itself, and complexation is the main driving force for Sb removal, assisted by electrostatic attraction. The future directions of Sb removal by adsorption focus on the shortcomings of current adsorbents; more attention should be given to the practicability of adsorbents and their disposal after use. This review contributes to the development of effective adsorbents for removing Sb and provides an understanding of Sb interfacial processes during Sb transport and the fate of Sb in the water environment.

Liquid-solid ratio during hydrothermal carbonization affects hydrochar application potential in soil: Based on characteristics comparison and economic benefit analysis

Returning straw-like agricultural waste to the field by converting it into hydrochar through hydrothermal carbonization (HTC) is an important way to realize resource utilization of waste, soil improvement, and carbon sequestration. However, the large-scale HTC is highly limited by the large water consumption and waste liquid pollution. Here, we propose strategies to optimize the liquid-solid ratio (LSR) of HTC, and comprehensively evaluate the stability, soil application potential, and economic benefits of corn stover-based hydrochar under different LSRs. The results showed that the total amount of dissolved organic carbon of hydrochars increased by 55.0% as LSR reducing from 10:1 to 2:1, while the element content, thermal stability, carbon fixation potential, specific surface area, pore volume, and functional group type were not obviously affected. The specific surface area and pore volume of hydrochar decreased by 61.8% and 70.9% as LSR reduced to 1:1, due to incomplete carbonization. According to the gray relation, hydrochar derived at LSR of 10:1 and followed by 2:1 showed greatest relation degree of 0.80 and 0.70, respectively, indicating better soil application potential. However, reducing LSR from 10:1 to 2:1 made the income of single process production increased from -388 to 968 ¥, and the wastewater generation decreased by 80%. Considering the large-scale application of HTC in fields for farmland improvement and environmental remediation, the comprehensive advantages of optimized LSR will be further highlighted.

In situ synthesis of label-free electrochemical aptasensor-based sandwich-like AuNPs/PPy/Ti3C2Tx for ultrasensitive detection of lead ions as hazardous pollutants in environmental fluids

The monitoring of hazardous pollutants in environmental fluids is one of main stretaegy in investigation of water and soil quality. Metal ions are one of main and dangerius materials in water sampels and one of the main causes of environmental problems. Therefore, many of environmental researchers focused on fabrication of highly sensitive sensor to ion hazardous pollutants environmental fluids. The encapsulation of 2D MXenes with other stable materials has proven to be an effective method for enhancing their stability and electrochemical properties. In this work, a sandwich-like nanocomposite structure, AuNPs/PPy/Ti₃C₂T_x, was designed and synthesized via a facile method of one-step layer-by-layer self-assembly. The morphology and structure of the prepared nanocomposites are characterized with various methods such as scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). Ti₃C₂T_x as a substrate played a significant role in the synthesis and alignment of PPy and AuNPs growth. The nanocomposites have maximized the benefits of the inorganic AuNPs and organic PPy materials, enhancing their stability and electrochemical performance. Meanwhile, AuNPs have given the nanocomposite the ability to form covalent bonds with biomaterials via the Au-S bond. Thus, a novel electrochemical aptasensor was developed based on AuNPs/PPy/Ti₃C₂T_x for the sensitive and selective detection of Pb²⁺. It demonstrated a wide linear range from 5 × 10^-14 to 1 × 10^-8 M with a low LOD of 1 × 10^-14 M (S/N = 3). Additionally, the developed aptasensor exhibited excellent selectivity and stability and successfully used to sensing of Pb²⁺ in environmental fluids such as NongFu Spring and tap water.

The bio-adsorption competence of tailor made lemon grass adsorbents on oils: An in-vitro approach

The oil contamination in aquatic system is considered as most serious environmental issues and identifying a suitable ecofriendly solution for this oil pollution management is critical. Hence, this research was designed to evaluate the oils (petrol, diesel, engine oil, and crude oil) adsorptive features through raw lemon grass adsorbent, physically/chemically treated adsorbents. Initially, such raw and treated adsorbents were characterized by Scanning Electron Microscope (SEM), Fourier transform infrared spectroscopy (FTIR), and Energy-Dispersive X-ray Spectroscopy (EDS) analysis. These characterization techniques revealed that the lemon grass adsorbent had considerable level of pollutant adsorption potentials owing to porous morphological structure, active functional groups and pollutants interaction with chemical elements. The physically treated adsorbent exhibited better adsorption characteristics than others. Accordingly, the petrol adsorption potential of raw adsorbent, physically treated and chemically treated ones was discovered as their weight incremented up to 2.0, 3.0, and 1.5 times their initial weight, respectively. Similarly, the weight of raw form, physically and chemically treated ones on diesel had increased significantly, up to 2.5 times, 4.0 times, and 2.0 times, respectively. It was evaluated that the weight of these tested adsorbents on engine oil incremented by 3.5, 5.0, and 3.0 times their initial weight, while on crude oil these incremented by 4.0, 6.0, and 4.0 times their initial weight respectively. When the media are compared, it's indeed evident about absorption which is preferred as follows: Crude oil, engine oil, diesel, and petrol. The physically treated lemon grass adsorbent showed maximum adsorption and retention potential than others. The kinetic study reveals that the pseudo second order kinetics is the best fit for the adsorption of oil with R² value of 0.99.

New insights on the adsorption of floral odorants on Apis cerana cerana olfactory receptor AcerOr1: Theoretical modeling and thermodynamic study

Apis cerana cerana counted on its sensitive olfactory system to make survival activities in the surrounding environment and the olfactory receptors can be considered as a primary requirement of odorant detection, recognition and coding. Indeed, the exploitation of the olfactory system of insects in particular the Asian honeybee "Apis cerana cerana" can be the best experimental model to investigate the essentials of the chemosensitivity and may help to better understand the olfactory perception in insects. Hence, an advanced statistical physics modeling via the monolayer model with single energy (n ≠ 1) of the three dose-olfactory responses curves indicated that undecanoic acid, 1-octyl alcohol and 1-nonanol were docked with a mixed parallel and non-parallel orientation on AcerOr1. Furthermore, in the present work, the Apis cerana cerana olfactory receptor AcerOr1 showed high sensitivity and discrimination power to detect undecanoic acid, 1-octyl alcohol and 1-nonanol with concentrations at half saturations values of 10^-7 mol/L and the molar adsorption energy values obtained from data fitting results, which were ranged from 17.91 to 24.00 kJ/mol, confirmed the exothermic and the physisorption nature of the adsorption of the studied floral odorants on AcerOr1. The studied experimental dose-response curves of undecanoic acid, 1-octyl alcohol and 1-nonanol provided access to quantitative (i.e., stereographic and energetic) characterizations of AcerOr1 via the determination of the olfactory receptor site size distributions (RSDs) and the adsorption energy distributions (AEDs). The stereographic characterization showed RSDs spread out from 0.20 to 8 nm presenting average values corresponding to the maximum of the peaks at 1.50 nm, at 1.10 nm and at 1.04 nm for undecanoic acid, 1-octyl alcohol and 1-nonanol, respectively. The energetic characterization presented AEDs ranged from 0 to 40 kJ/mol showing an approximate adsorption energy bands defined between 7.50 and 27.50 kJ/mol, between 15 and 33 kJ/mol and between 13.50 and 34.50 kJ/mol for undecanoic acid, 1-octyl alcohol and 1-nonanol, respectively. The utilization of the analytical expression of the olfactory threshold allowed giving important and helpful informations about the occupation rate of AcerOr1 binding sites that fired a minimal olfactory response at a honeybee olfactory receptor. Hence, the olfactory response can be detected only when 1.97 %, 1.13 % and 2.00 % of AcerOr1 binding sites were occupied by undecanoic acid, 1-octyl alcohol and 1-nonanol, respectively. Lastly, by means of the selected model, the thermodynamic potentials, such as the adsorption entropy, the Gibbs free enthalpy and the internal energy could be calculated and interpreted.

Selective Removal of Boron from Aqueous Solutions Using ECH@NGM Aerogels with Excellent Hydrophilic and Mechanical Properties: Performance and Response Surface Methodology Analysis

The remediation of environmental boron contamination has received extensive research attention. The adsorbent ECH@NGM aerogel with high hydrophilic and mechanical properties was synthesized to remove boron. The ECH@NGM aerogel had a high adsorption capacity of 81.11 mg/g, which was 14.50% higher than that of commercial boron-selective resin Amberlite IRA743. The Freundlich model and pseudo-second-order model described the adsorption behavior well. In addition, the response surface methodology (RSM) could predict the experimental outcomes and optimize the reaction conditions, and X-ray photoelectron spectroscopy (XPS) and control tests were utilized to investigate probable adsorption mechanisms. These data showed that the B ← N coordination bond was the primary adsorption force. The adsorbent had good resistance to interference from coexisting salts, high reusability, good adsorption performance even after five reuse cycles, and a high desorption rate in a relatively short time. The adsorption performance in real brines could be maintained at 80%. Therefore, this work not only provided ECH@NGM aerogels for the removal of boron from brine but also elucidated the main adsorption processes between N-containing adsorbents and boron, facilitating the design of future adsorbents for boron removal.