Electrochemical sensor for Isoniazid based on the glassy carbon electrode modified with reduced graphene oxide–Au nanomaterials

An ultrasensitive genosensor for detection of toxigenic and non-toxigenic Clostridioides difficile based on a conserved sequence in surface layer protein coding gene

Clostridioides difficile (C. difficile) is the most common agent of antibiotic-associated diarrhea, leading to intestinal infection through the secretion of two major toxins. Not all strains of this bacterium are toxigenic, but some of them cause infection via their accessory virulence factors, such as surface layer protein (SlpA). SlpA is conserved in both toxigenic and non-toxigenic strains of C. difficile. In the present work, an amplification-free electrochemical genosensor was designed for the detection of the slpA gene. A glassy carbon electrode coated with gold nanoparticle-reduced graphene oxide nanocomposite was used as the working electrode, and its surface was modified using a simple thiolated linear oligonucleotide as the bioreceptor. Moreover, the hexaferrocenium tri[hexa(isothiocyanato) iron(III)] trihydroxonium (HxFc) complex was used as an intercalator, and its redox signal was recorded using differential pulse voltammetry. Scan rate studies indicated a quasi-reversible adsorption-controlled process for the HxFc complex. This genosensor showed high sensitivity with a limit of detection of 0.2 fM, a linear response range of 0.46-1900 fM, and a satisfactory specificity toward the synthetic slpA target gene. Also, the genosensor indicated responses in the mentioned linear range toward the genome extracted from either toxigenic or non-toxigenic strains of C. difficile.

Green synthesis of CQDs for determination of iron and isoniazid in pharmaceutical formulations

Camphor leaves were used as the precursor for the hydrothermal synthesis of carbon quantum dots. The preparation method is simple and rapid, and the raw material is environmentally friendly and easy to obtain. Without additional modification, the carbon quantum dots were used as fluorescent probes for the sensitive and selective detection of Fe³⁺ and isoniazid at different excitation wavelengths. For Fe³⁺, at the excitation wavelength of 320 nm, the ratio of fluorescence intensity of CQD solution after adding Fe³⁺ to CQD solution without Fe³⁺ addition, F/F₀, and Fe³⁺ concentration showed a good linear relationship in the range of 2.72 × 10^-5 to 1.00 × 10^-4 mol L^-1 (R² = 0.9912), and the limit of detection was 8.16 μmol L^-1. For isoniazid, at the excitation wavelength of 270 nm, the ratio of fluorescence intensity of CQDs solution with isoniazid to CQDs solution without isoniazid, F/F₀, and isoniazid concentration showed good linear relationships in the range of 3.81 × 10^-6 to 1.00 × 10^-5 mol L^-1 (R² = 0.9941) and 1.00 × 10^-5 to 2.10 × 10^-4 mol L^-1 (R² = 0.9910) respectively, and the limit of detection was 1.14 μmol L^-1. A fluorescence method for the determination of Fe and isoniazid content was proposed. The method has been used to detect iron in iron supplement tablets and isoniazid in isoniazid tablets with satisfactory results.

A highly sensitive and ecofriendly assay platform for the simultaneous electrochemical determination of rifampicin and isoniazid in human serum and pharmaceutical formulations

Simple fabrication of an electrochemical sensor for simultaneous determination of rifampicin and isoniazid based on electrochemical modification of SPCE surface with reduced graphene oxide and nickel hydroxide film (Ni(OH)2/rGO/SPCE) without using toxic chemical agents.

Bimetallic cobalt-iron diselenide nanorod modified glassy carbon electrode: an electrochemical sensing platform for the selective detection of isoniazid

The increasing demand of a sensitive and portable electrochemical sensing platform in pharmaceutical analysis has developed widespread interest in preparing electrode materials possessing remarkable properties for the electrochemical determination of target drug analytes. Herein, we report the synthesis, characterization and application of bimetallic cobalt-iron diselenide (FeCoSe₂) nanorods as electrode modifiers for the selective detection of a commonly used anti-tuberculosis drug Isoniazid (INZ). We prepared FeCoSe₂ nanorods by a simple hydrothermal route and characterized these by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX) and temperature-programmed reduction (TPR) techniques. The electrochemical characterization of FeCoSe₂ modified GCE was performed by cyclic voltammetry (CV) and square wave anodic stripping voltammetry (SWASV). Under optimized experimental conditions, a linear current-concentration response was obtained for INZ in the range of 0.03–1.0 μM, with very low limit of detection 1.24 × 10⁻¹⁰ M. The real applicability of the designed FeCoSe₂/GCE sensing platform was adjudicated by the detection of INZ in biological samples.

FeCoSe₂ bimetallic nanorods were synthesized by hydrothermal method. The modified electrode responded excellently towards isoniazid detection with LOD of 1.24 × 10⁻¹⁰ M. FeCoSe₂/GCE showed applicability for INZ detection in real samples.

A simple signal-on strategy for fluorescent detection of tuberculostatic drug isoniazid based on Ag clusters-MnO2 sheets nanoplatform

As a first-line tuberculostatic drug, isoniazid (INH) plays effective and irreplaceable role in prevention and treatment of tuberculosis. In this work, a rapid and simple signal-on fluorescence approach is established for INH assay by employing a platform composed of silver nanoclusters (AgNCs) and MnO₂ nanosheets. In the proposed sensing system, strong red fluorescence of poly (methacrylic acid)-stabilized AgNCs can be greatly quenched after they attach to the surfaces of MnO₂ nanosheets. With the addition of INH, MnO₂ nanosheets are reduced to Mn²⁺ and subsequently release the AgNCs, which leads to obvious fluorescence recovery again. Based on this mechanism, highly sensitive detection of INH in the range of 0.8-200 μM is realized (detection limit: 476 nM). The present strategy shows remarkable advantages including simplicity, rapidness, high sensitivity and wide detectable range. This method is also practical and comparable to high-performance liquid chromatography, which can be applied to detect INH in human urine and serum samples as well as pharmaceutical products.

Development of a Novel Nanocomposite Based on Reduced Graphene Oxide/Chitosan/Au/ZnO and Electrochemical Sensor for Determination of Losartan

Background:

Hypertension is a major risk for morbidity and mortality, while hypertension is associated with cardiovascular disease and organ damage. Recent research efforts have focused on the development of highly selective angiotensin receptor blockers. In which losartan (LOS) is considered as a new generation of an effective oral drug product against arterial hypertension. Therefore, the determination of drugs in biological fluids, pharmaceuticals (tablets), and wastewater is of critical importance for clinical applications, forensics, quality control, and environmental protection that call for the development of analytical methods. Many ranges of methods such as spectroscopic methods and chromatographic techniques have been developed to determine LOS in pharmaceutical formulations and biological fluids. However, there are crucial interference problems in these methods. For these reasons, more sensitive, desirable, portable, low-cost, simple, and selective nanocomposite-based sensors are needed in terms of health safety. Nanomaterials such as reduced graphene oxide, chitosan, and metal nanoparticles are used to improve the sensitivity in the development of electrochemical sensors.

Objective:

In this study, a novel reduced graphene oxide (RGO), chitosan (Chit), gold (Au), and zinc oxide (ZnO) nanocomposite (RGO/Chitosan/Au/ZnO) was synthesized and used to develop a sensitive and efficient electrochemical sensor for LOS detection.

Methods:

Modification of electrode by RGO/Chit/Au/ZnO nanocomposite was performed in four stages with GO (at -2.0 V for 150 s), Chitosan (at -3.0 V for 300 s), Au nanoparticles (at -0.4 V for 400 s), and Zn nanoflowers like (at -0.7 V for 1200 s). The RGO/Chitosan/Au/ZnO nanocomposite was characterized by field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR). Cyclic Voltammetry (CV) and Differential Pulse Voltammetry (DPV) were used to detect LOS, and the influence of pH value, scan rate, accumulation potential, and time also losartan concentration on the performance of ZnO/Au/Chitosan/RGO/GCE were investigated. In order to investigate the selectivity of the modified electrode for the determination of LOS, the effect of possible interfering species was evaluated and showed that these species are not interferences. Also, the reproducibility of the modified electrode was investigated and implying that the RGO/Chit/Au/ZnO nanocomposite was highly reproducible.

Results:

The modified electrode was used as a sensor for the selective and sensitive determination of LOS with a detection limit of 0.073 μM over the dynamic linear range of 0.5μM to 18.0 μM. In addition, electrochemical oxidation of LOS was well recovered in pharmaceutical formulations.

Conclusion:

LOS is used to treat high blood pressure, taking into account the oxidation of this compound, the use of electrochemical based sensors, ideally suited to a specific chemical species, can be fully selectable and High-sensitivity answer is very important. In this study, the electrodes with RGO/Chit/Au/ZnO nanocomposite were modified by the electrochemical method. Nanocomposites were characterized by various methods such as FE-SEM, FT-IR, XRD, Raman, and XPS. The electrocatalytic activity of the modified electrode was then investigated for measuring LOS. According to the results of the modified electrode, high sensitivity, reproducibility, and selectivity have been shown to oxidize this composition.

Highly Sensitive Amperometric α-Ketoglutarate Biosensor Based on Reduced Graphene Oxide-Gold Nanocomposites

Herein, a rapid and highly sensitive amperometric biosensor for the detection of α-ketoglutarate (α-KG) was constructed via an electrochemical approach, in which the glutamate dehydrogenase (GLUD) was modified on the surface of reduced graphene oxide-gold nanoparticle composite (rGO-Aunano composite). The rGO-Aunano composite was one-step electrodeposited onto glassy carbon electrode (GCE) surface and was characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and electrochemical techniques. In addition, the rGO-Aunano/GCE was also found to electrocatalyze the oxidation of β-nicotinamide adenine dinucleotide (NADH) at the peak potential of 0.3 V, which was negatively shifted compared with that at bare GCE or Aunano/GCE, illustrating better catalytic performance of rGO-Aunano. After the modification of GLUD, the GLUD/rGO-Aunano/GCE led to effective amperometric detection of α-KG through monitoring the NADH consumption and displayed a linear response in the range of 66.7 and 494.5 μM, with the detection limit of 9.2 μM. Moreover, the prepared GLUD/rGO-Aunano/GCE was further evaluated to be highly selective and used to test α-KG in human serum samples. The recovery and the RSD values were calculated in the range of 97.9-102.4% and 3.8-4.5%, respectively, showing a great prospect for its real application.

Electroanalysis of isoniazid and rifampicin: Role of nanomaterial electrode modifiers

Thanks to operational simplicity, speediness, possibility of miniaturization and real-time nature, electrochemical sensing is a supreme alternative for non-electrochemical methodologies in drug quantification. This review, highlights different nanotech-based sensory designs for electroanalysis of isoniazid and rifampicin, the most important medicines for patients with tuberculosis. We first, concisely mention analyses with bare electrodes, associated impediments and inspected possible strategies and then critically review the last two decades works with focus on different nano-scaled electrode modifiers. We organized and described the materials engaged in several categories: Surfactants modifiers, polymeric modifiers, metallic nanomaterials, carbon based nano-modifiers (reduced graphene oxide, multi-walled carbon nanotubes, ordered mesoporous carbon) and a large class of multifarious nano composites-based sensors and biosensors. The main drawbacks and superiorities associated with each array as well as the current trend in the areas is attempted to discuss. Summary of 79 employed electrochemical approaches for analysis of isoniazid and rifampicin has also been presented.

A chitosan grafted mesoporous carbon aerogel for ultra-sensitive voltammetric determination of isoniazid

A screen-printed carbon electrode (SPCE) was modified with chitosan (Chit) supported on carbon aerogel (CA) to obtain an electrochemical sensor for the tuberculosis drug isoniazid (INZ). The interconnected mesoporous structure of Chit/CA provides a large surface area (S_BET = 461 m² g^-1) and good porosity (V_Tot = 0.69 cm³ g^-1). Besides, the modified SPCE displayed enhanced electrocatalytic activity due to the presence of numerous active sites (such as >C=O, -NH-, -NH₂, -OH). Figures of merit include (a) a typical working voltage of 0.28 V (vs. Ag/AgCl), (b) high sensitivity (8.09 μA μM^-1 cm^-2), (c) a wide linear response to INZ (0.01-115 μM) and (d) a low detection limit (8 nM). The modified electrode has successfully been applied to the determination of INZ in spiked serum and urine, and recoveries ranged from 97.8 to 99.8%. Graphical abstract Schematic illustration of preparation and applications of a nanocomposite consisting of chitosan (Chit; CS) supported on carbon aerogel (CA) for electrochemical detection of isoniazid.

Investigation of Sensitivities and Drift Effects of the Arrayed Flexible Chloride Sensor Based on RuO₂/GO at Different Temperatures

We investigate the temperature effect on sensing characteristics and drift effect of an arrayed flexible ruthenium dioxide (RuO₂)/graphene oxide (GO) chloride sensor at different solution temperatures between 10 °C and 50 °C. The average sensor sensitivities according to our experimental results were 28.2 ± 1.4 mV/pCl (10 °C), 42.5 ± 2.0 mV/pCl (20 °C), 47.1 ± 1.8 mV/pCl (30 °C), 54.1 ± 2.01 mV/pCl (40 °C) and 46.6 ± 2.1 mV/pCl (50 °C). We found the drift effects of an arrayed flexible RuO₂/GO chloride sensor in a 1 M NaCl solution to be between 8.2 mV/h and 2.5 mV/h with solution temperatures from 10 °C to 50 °C.

Theoretical and experimental evidence for rGO-4-PP Nc as a metal-free Fenton-like catalyst by tuning the electron distribution

A new metal-free Fenton-like catalyst (rGO-4-PP Nc) was investigated by DFT, a dual-reaction-center mechanism was proposed and verified during the Fenton reaction.

An Enzyme-Induced Novel Biosensor for the Sensitive Electrochemical Determination of Isoniazid

In this present work, a glassy carbon electrode (GCE) was modified primarily with multiwalled carbon nanotubes (MWCNTs) and a composite of MWCNTs and titanium oxide nanoparticles (TiO₂NPs). The enzyme horseradish peroxidase (HRP) was immobilized to enhance the sensing ability of GCE. The proposed biosensor was used for the sensitive determination of isoniazid (INZ) in various pharmaceutical samples. The electrochemical behaviour of the developed MWCNT-TiO₂NPs-HRP-GCE biosensor was studied by using cyclic voltammetry (CV) and differential pulse voltammetric (DPV) techniques. Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetry (TGA) and transmission electron microscopy (TEM) techniques were used to characterize the developed sensor. Phosphate buffer solution (PBS) with pH 7 was used as supporting electrolyte in the present investigation. The cyclic voltammetric results revealed that the increment of anodic peak currents for the enzyme-induced sensor was almost 8-fold greater than that of a bare GCE. The DPV technique exhibited good limit of detection and limit of quantification values, viz., 0.0335 μM and 0.1118 μM, respectively. Moreover, the developed sensor showed long-lasting stability and repeatability without any interferents. This strongly indicates that the fabricated sensor shows outstanding electrochemical performance towards INZ, with excellent selectivity and sensitivity. The developed sensor was successfully applied to pharmaceutical samples and gave good percentages of recoveries.

Fabrication of 3D honeycomb-like porous polyurethane-functionalized reduced graphene oxide for detection of dopamine

A three dimensional reduced graphene oxide/polyurethane (RGO-PU) porous material with connected pores was prepared by physical adsorption of RGO onto the surface of porous PU. The porous PU was prepared by directional melt crystallization of a solvent, which produced high pores with controlled orientation. The prepared RGO-PU was characterized by scanning electron microscopy, spectroscopy and electro-chemical methods. The RGO-PU porous material revealed better electrochemical performance, which might be attributed to the robust structure, superior conductivity, large surface area, and good flexibility. Differential pulse voltammetry (DPV) analysis of DA using the RGO-PU exhibited a linear response range over a wide DA concentration of 100-1150pM, with the detection limit of 1pM. This sensor exhibited outstanding anti-interference ability towards co-existing molecules with good stability, sensitivity, and reproducibility. Furthermore, the fabricated sensor was successfully applied for the quantitative analysis of DA in human serum and urine samples with acceptable recovery, which indicates its feasibility for practical application.