Effects of the micro/nanostructure of electrospun zein fibres on cells in simulated blood flow environment

Optimization of Electrospun Bilayer Vascular Grafts through Assessment of the Mechanical Properties of Monolayers

Small-diameter vascular grafts must be obtained with the most appropriate materials and design selection to harmoniously display a variety of features, including adequate tensile strength, compliance, burst strength, biocompatibility, and biodegradability against challenging physiological and hemodynamic conditions. In this study, monolayer vascular grafts with randomly distributed or radially oriented fibers are produced using neat, blended, and copolymer forms of polycaprolactone (PCL) and poly(lactic acid) (PLA) via the electrospinning technique. The blending ratio is varied by increasing 10 in the range of 50-100%. Bilayer graft designs are realized by determining the layers with a random fiber distribution for the inner layer and radial fiber orientation for the outer layer. SEM analysis, wall thickness and fiber diameter measurements, tensile strength, elongation, burst strength, and compliance tests are done for both mono- and bilayer scaffolds. The findings revealed that the scaffolds made of neat PCL show more flexibility than the neat PLA samples, which possess higher tensile strength values than neat PCL scaffolds. Also, in blended samples, the tensile strength values do not show a significant improvement, whereas the elongation values are enhanced in tubular samples, depending on the blending ratio. Also, neat poly(l-lactide-co-caprolactone) (PLCL) samples have both higher elongation and strength values than neat and blended scaffolds, with some exceptions. The blended specimens comprising a combination of PCL and PLA, with blending ratios of 80/20 and 70/30, exhibited the most elevated burst pressures. Conversely, the PLCL scaffolds demonstrated superior compliance levels. These findings suggest that the blending approach and fiber orientation offer enhanced burst strength, while copolymer utilization in PLCL scaffolds without fiber alignment enhances their compliance properties. Thus, it is evident that using a copolymer instead of blending PCL and PLA and combining the PLCL layer with PCL and PLA monolayers in bilayer vascular graft design is promising in terms of mechanical and biological properties.

Self-assembled zein organogels as in situ forming implant drug delivery system and 3D printing ink

Recently, biomedical applications of organogels have been increasing; however, there is a demand for bio-based polymers. Here, we report self-assembled zein organogels in N-methyl pyrrolidone (NMP), Dimethyl sulfoxide (DMSO), and glycerol formal (GF). The gel formation was driven by the solvent's polarity and the hydrogen bonding component of Hansen Solubility Parameters was important in promoting gelation. Gels exhibited shear-thinning and thixotropic properties. Furthermore, water-induced self-assembly of zein allows mechanically robust in situ implant formation by solvent exchange. Ciprofloxacin was incorporated as a model drug and sustained release depending upon the solvent exchange rate was observed. In situ implants in agarose gel retained antibacterial efficacy against S. aureus for more than 14 days. Zein-based organogels were further applied as 3D printing ink and it was found that zein gel in DMSO had superior printability than gels prepared in NMP and GF. Using three solvents to prepare organogels can enable the encapsulation of various drugs and facilitate the preparation of composite gels with other biocompatible polymers. These organogel systems can further be used for developing 3D printed drug delivery systems or scaffolds for tissue engineering.

Improvement of mechanical properties of zein porous scaffold by quenching/electrospun fiber reinforcement

As a novel bone substitute material, zein-based scaffolds (ZS) should have suitable mechanical properties and porosity. ZS has shown good compressive properties matching cancellous bone, but there is still a demand to improve its mechanical properties, especially tensile and bending properties without adding plasticizers. The present study explored two simple and environment-friendly factors for this purpose: fiber reinforcement and quenching. Addition of electrospun zein fibers enhanced all mechanical properties significantly including compressive, tensile, and bending moduli; compressive and bending strengths of ZS with both higher (70-80%) and lower (50-60%) porosities, no matter whether heating treated or not treated. Especially, all these parameters were further enhanced significantly by addition of heating treated fibers. AFM provided evidence that high temperature modification could significantly alter the micro-elastic properties of zein electrospun fibers, i.e., increased stiffness of fibers. Quenching treatment also enhanced compressive, tensile, and bending strengths significantly. Finally, quenching treated ZS were implanted into critical-sized bone defects (15 mm) of the rabbit model to compare the repair efficacy with a commercial β-tricalcium phosphate product. The results demonstrated that there were no remarkable differences in bone reconstructions between these two materials.

Electrospun nanofiber scaffold for vascular tissue engineering

Due to the prevalence of cardiovascular diseases, there is a large need for small diameter vascular grafts that cannot be fulfilled using autologous vessels. Although medium to large diameter synthetic vessels are in use, no suitable small diameter vascular graft has been developed due to the unique dynamic environment that exists in small vessels. To achieve long term patency, a successful tissue engineered vascular graft would need to closely match the mechanical properties of native tissue, be non-thrombotic and non-immunogenic, and elicit the proper healing response and undergo remodeling to incorporate into the native vasculature. Electrospinning presents a promising approach to the development of a suitable tissue engineered vascular graft. This review provides a comprehensive overview of the different polymers, techniques, and functionalization approaches that have been used to develop an electrospun tissue engineered vascular graft.