Green synthesis of zinc doped cobalt ferrite nanoparticles: Structural, optical, photocatalytic and antibacterial studies

Biomedical Applications of Green Synthesized Zinc Oxide and Magnesium-Doped Zinc Oxide Nanoparticles Using Aqueous Extract of Ziziphus Oxyphylla Leaves

Zinc oxide (ZnO) and magnesium-doped zinc oxide (Mg-doped ZnO) nanoparticles (NPs) were synthesized using Ziziphus oxyphylla 's aqueous leaf extract as reducing agent. UV-Vis absorption peaks at 324 nm and 335 nm were indicative of ZnO and Mg-doped ZnO, respectively. FTIR absorption bands observed at 3238, 1043, 1400, 1401, 2186 and 2320 cm -1 suggested the presence of phenols, alcohols, saturated hydrocarbons, and possibly alkynes. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy revealed pure, spherical and agglomerated NPs with average size of 35.9 nm (ZnO) and 56.8 nm (Mg-doped ZnO). Both NPs remained active against all bacterial strains with the highest inhibition zones observed against Proteus vulgaris (21.16±1.25 mm for ZnO and 24.1±0.76 mm for Mg-doped ZnO. EtBr fluorescence (cartwheel assay) indicated efflux pump blockage, suggesting its facilitation in the bacterial growth inhibition. Antioxidant potential, determined via DPPH radical scavenging assay, revealed stronger antioxidant potential for Mg-doped ZnO (IC [Formula: see text]/mL) than pure ZnO (IC [Formula: see text]/mL). Furthermore, both NPs showed antileishmanial activity against Leishmania tropica promastigotes (IC [Formula: see text]/mL for Mg-doped ZnO and 64.34±6.56 for ZnO), while neither NP exhibited significant hemolysis, indicating biocompatibility and further assessment for their drugability.

Study of Cation Distribution and Photocatalytic Activity of Nonthermal Plasma-Modified NiZnFe2O4 Magnetic Nanocomposites

In this study, NiZnFe2O4 composite was synthesized using a sol-gel route and subjected to nonthermal plasma treatment for tailoring their cations' distribution and physicochemical, magnetic, and photocatalytic properties. Microwave plasma treatment was given to the composites for 60 min in support of postsynthesis sintering at 700 °C for 5 h. X-ray diffraction (XRD) analysis was conducted on pre- and postplasma-modified ferrite composites to identify phase-pure cubic spinel structure and cations' distribution. The cation distributions were measured from the ratio of XRD intensity peaks corresponding to (220), (311), (422) and (440) planes. The intensity ratio of plasma-treated ferrite composites decreased compared to that of pristine composites. The crystallite size and lattice constant were increased on plasma treatment of the composite. The morphological analysis showed nanoflower-like structures of the particles with an increased surface area in the plasma-treated composites. The plasma oxidation and sputtering effects caused a reduction in the nanoflower size. The energy bandgap increased with a decrease in particle size due to plasma treatment. The rhodamine B dye solution was then irradiated with a light source in the presence of the nanocomposites. The dye degradation efficiency of the composite photocatalyst increased from 80 to 96% after plasma treatment.

Bi-doped BaBiO3 (x = 0%, 5%, 10%, 15%, and 20%) perovskite oxides by a sol-gel method: comprehensive biological assessment and RhB photodegradation

The BaBiO3 (BBO) perovskite oxide was prepared via a sol-gel method with different concentrations of Bi nitrate and examined as a photocatalyst for RhB degradation under sunlight, and its antioxidant and antibacterial activities were examined. X-ray diffraction (XRD) indicated the formation of a BaBiO3-BaCO3 (BBO-BCO) binary composite. For the degradation of RhB under solar radiation, high photocatalytic activity (73%) was observed. According to the antibacterial activity study, the addition of Bi enhanced the antibacterial activity of the resulting material against both Gram-positive and Gram-negative microorganisms. The Bi%-BBO (Bi 20%) inhibited 96.23% S. aureus. 10% Bi-BBO as an antioxidant agent had the most efficacious IC50 value of 2.50 mg mL-1. These results seem to suggest that BBO-BCO is a promising catalytic material with potential application in the fields of catalysis and medicine.

Green synthesis of nickel-doped magnesium ferrite nanoparticles via combustion for facile microwave-assisted optical and photocatalytic applications

NixMg1-xFe2O4(x = 0, 0.2, 0.4, 0.6) nanoparticles were symphonized via combustion with microwave assistance in the presence of Tamarindus indica seeds extract as fuel. Nanoparticles nature, size, morphology, oxidation state, elemental composition, and optical and luminescence properties were analysed using PXRD, FTIR, SEM, EDX, and HRTEM with SAED, XPS, UV-Visible and photoluminescence spectroscopy. PXRD analysis confirms that synthesized nanoparticles are spinel cubic and have a 17-18 nm average crystalline size. Tetrahedral and octahedral sites regarding stretching vibrations were confirmed by FTIR analysis. SEM and HRTEM data it is disclosed that the morphology of synthesized nanoparticles has nano flakes-like structure with sponge-like agglomeration. Elemental compositions of prepared nanoparticles were confirmed through EDX spectroscopy. XPS Spectroscopy confirmed and revealed transition, oxidation states, and elemental composition. The band gap and absorption phenomenon were disclosed using UV-visible spectroscopy, where the band gap declines (2.1, 2, 1.6, 1.8 eV), with increase in nickel NixMg1-xFe2O4(x = 0, 0.2, 0.4, 0.6) doping. Photoluminescence intensity reduces with an incline in nickel doping, was confirmed and disclosed using photoluminescence spectroscopy. Dyes (Methylene blue and Rhodamine B) degradation activity was performed in the presence of NDMF nanoparticles as a photocatalyst, which disclosed that 98.1% of MB dye and 97.9% of RB dye were degraded in 0-120 min. Regarding initial dye concentration and catalyst load, 5 ppm was initiated as the ideal initial concentration for both RB and MB dyes. 50 mg catalyst dosage was found to be most effective for the degradation of MB and RB dyes. In comparison, pH studies revealed that photodegradation efficiency was higher in neutral (MB-98.1%, RB-97.9%) and basic (MB-99.6%, RB-99.3%) conditions than in acidic (MB-61.8%, RB-60.4%) conditions.

Utilization of ZnFe2O4-Polyaniline (PANI), ZnFe2O4-Polystyrene (PST), and ZnFe2O4-Polypyrrole (PPy) nanocomposites for removal of Red X-GRL and Direct Sky Blue dyes from wastewater: Equilibrium, kinetic and thermodynamic studies

In this study, ZnFe2O4-Polyaniline (PANI), ZnFe2O4-Polystyrene (PST), and ZnFe2O4-Polypyrrole (Ppy) nanocomposites were synthesized by the adsorption method and characterized by field emission scanning electron microscopy and Fourier transform infrared spectrometer. Batch adsorption experiments were conducted for removing two types of hazardous dyes Red X-GRL and Direct Sky Blue 51 from an aqueous solution and the effect of pH, adsorbent dosage, contact time, and initial concentration of dyes were investigated. Meanwhile, kinetic, isotherm, and thermodynamic parameters were also determined. The electrolyte and surfactant effect was also tested for the prepared nanocomposites. To test the reusability desorption study was also conducted.

Hybrid nanostructures exhibiting both photocatalytic and antibacterial activity-a review

The most vital issues of the modern world for a sustainable future are "health" and "the environment." Scientific endeavors to tackle these two major concerns for mankind need serious attention. The photocatalytic activity toward curbing environmental pollution and antibacterial performance toward a healthy society are two directions that have been emphasized for decades. Recently, materials engineering, in their nanodimension, has shown tremendous possibilities to integrate these functionalities within the same materials. In particular, hybrid nanostructures have shown magnificent prospects to combat both crucial challenges. Many researchers are separately engaged in this important field of research but the collective knowledge on this domain which can facilitate them to excel is badly missing. The present article integrates the development of different hybrid nanostructures which exhibit both photocatalytic degradations of environmental pollutants and antibacterial efficiency. Various synthesis techniques of those hybrid nanomaterials have been discussed. Hybrid nanosystems based on several successful materials have been categorically discussed for better insight into the research advancement in this direction. In particular, Ag-based, metal oxides-based, layered carbon material-based, and Mexene- and self-cleaning-based materials have been chosen for detailing their performance as anti-pollutant and antibacterial materials. Those hybrid systems along with some miscellaneous booming nanostructured materials have been discussed comprehensively with their success and limitations toward their bifunctionality as antipollutant and antibacterial agents.

Photoluminescence, antibacterial, X-ray/gamma ray absorption, supercapacitor and sensor applications of ZrTiO4 nanorods

In the present communication, ZrTiO₄ nanoparticles (NPs) are synthesized by the solution combustion method using urea (ZTOU) and oxalyl dihydrazide (ODH) (ZTODH) as fuel and calcined at 700 °C. The synthesized samples were characterized with different techniques. Powder X-ray diffraction studies show the presence of diffraction peaks corresponding to ZrTiO₄. In addition to these peaks, a few additional peaks corresponding to the monoclinic and cubic phases of ZrO₂ and the rutile phase of TiO₂ are observed. The surface morphology of ZTOU and ZTODH consists of nanorods with different lengths. The TEM and HRTEM images confirm the formation of nanorods along with NPs, and the estimated crystallite size matches well with that of PXRD. The direct energy band gap was calculated using Wood and Tauc's relation and was found to be 2.7 and 3.2 eV for ZTOU and ZTODH respectively. The photoluminescence emission peaks (λ = 350 nm), CIE and CCT of ZTOU and ZTODH clearly confirm that the present nanophosphor might be a good nanophosphor material for blue or aqua green light emitting diodes. Furthermore, antibacterial activity and a viability test were conducted on two food borne pathogens. The X-ray/gamma ray absorption properties are also studied, which clearly show the ZrTiO₄ might be a good absorbing material. Furthermore, cyclic voltammetry (CV) analysis of ZTOU nanorods shows very good redox peaks compared to that of ZTODH. From the electrochemical impedance spectroscopy (EIS) measurements, the charge-transfer resistances for prepared nanorods ZTOU and ZTODH are found to be 151.6 Ω, and 184.5 Ω respectively. The modified graphite electrode with ZTOU shows good sensing activity for both paracetamol and ascorbic acid, compared to ZTODH.

The Influence of Zn Substitution on Physical Properties of CoFe2O4 Nanoparticles

Co1−xZnxFe2O4 nanoparticles (0 ≤ x ≤ 1) have been synthesized via a green sol−gel combustion method. The prepared samples were studied using X-ray diffraction measurements (XRD), transmission electron microscopy (TEM), Raman, and magnetic measurements. All samples were found to be single phases and have a cubic Fd-3m structure. EDS analysis confirmed the presence of cobalt, zinc, iron, and oxygen in all studied samples. Raman spectra clearly show that Zn ions are preferentially located in T sites for low Zn concentrations. Due to their high crystallinity, the nanoparticles show high values of the magnetization, which increases with the Zn content for x < 0.5. The magnetic properties are discussed based on Raman results. Co ferrite doped with 30% of Zn produced the largest SAR values, which increase linearly from 148 to 840 W/gMNPs as the H is increased from 20 to 60 kA/m.

Photocatalytic and Antibacterial Activity of CoFe2O4 Nanoparticles from Hibiscus rosa-sinensis Plant Extract

Biogenic CoFe₂O₄ nanoparticles were prepared by co-precipitation and Hibiscus rosa sinensis plant leaf was used as a bio-reductant of the nanoparticle productions. The biosynthesized CoFe₂O₄ nanoparticles were characterized by XRD, FTIR, UV, VSM, and SEM via EDX analysis. The cubic phase of biosynthesized CoFe₂O₄ nanoparticles and their crystallite size was determined by XRD. The Co-Fe-O bonding and cation displacement was confirmed by FTIR spectroscopy. The presence of spherically-shaped biosynthesized CoFe₂O₄ nanoparticles and their material were confirmed by SEM and TEM via EDX. The super-paramagnetic behaviour of the biosynthesized CoFe₂O₄ nanoparticles and magnetic pulse was established by VSM analysis. Organic and bacterial pollutants were eradicated using the biosynthesized CoFe₂O₄ nanoparticles. The spinel ferrite biosynthesized CoFe₂O₄ nanoparticles generate radical and superoxide ions, which degrade toxic organic and bacterial pollutants in the environment.

Engineered magnetic oxides nanoparticles as efficient sorbents for wastewater remediation: a review

The rapid urbanization and industrialization is causing worldwide water pollution, calling for advanced cleaning methods. For instance, pollutant adsorption on magnetic oxides is efficient and very practical due to the easy separation from solutions by an magnetic field. Here we review the synthesis and performance of magnetic oxides such as iron oxides, spinel ferrites, and perovskite oxides for water remediation. We present structural, optical, and magnetic properties. Magnetic oxides are also promising photocatalysts for the degradation of organic pollutants. Antimicrobial activities and adsorption of heavy metals and radionucleides are also discussed.

Soft Chemistry Synthesis and Characterization of CoFe1.8RE0.2O4 (RE3+ = Tb3+, Er3+) Ferrite

Nanosized CoFe1.8RE0.2O4 (RE3+ = Tb3+, Er3+) ferrites were obtained through wet ferritization method. These ferrites were characterized by X-ray diffraction (XRD), scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM/HR-TEM), Fourier transform infrared spectroscopy (FTIR), Mössbauer spectroscopy and magnetic measurements. The XRD results revealed that the average crystallite size is 5.77 nm for CoFe1.8Tb0.2O4 and 6.42 nm for CoFe1.8Er0.2O4. Distribution of metal cations in the spinel structure estimated from X-ray diffraction data showed that the Tb3+ and Er3+ ions occupy the octahedral sites. TEM images indicated the presence of polyhedral particles with average size 5.91 nm for CoFe1.8Tb0.2O4 and 6.80 nm for CoFe1.8Er0.2O4. Room temperature Mössbauer spectra exhibit typical nanoscaled cobalt ferrite spectra in good agreement with XRD and TEM data. The saturation magnetization value (Ms) is 60 emu/g for CoFe1.8Tb0.2O4 and 80 emu/g for CoFe1.8Er0.2O4. CoFe1.8RE0.2O4 nanoparticles showed similar antimicrobial efficacy against the five tested microbial strains, both in planktonic and biofilm state. The results highlight the promising potential of these types of nanoparticles for the development of novel anti-biofilm agents and materials.

Combustion-assisted green-synthesized magnesium-doped cadmium ferrite nanoparticles for multifunctional applications

Magnesium-doped cadmium ferrite nanoparticles, MgXCd1−XFe2O4 (where, X = 0, 0.2, 0.4, 0.6, 0.8, 1) were synthesized by a combustion method using curd as fuel.

Removal of Organic Dyes from Water and Wastewater Using Magnetic Ferrite-Based Titanium Oxide and Zinc Oxide Nanocomposites: A Review

Heterogeneous photocatalysis using titanium dioxide (TiO2) and zinc oxide (ZnO) has been widely studied in various applications, including organic pollutant remediation in aqueous systems. The popularity of these materials is based on their high photocatalytic activity, strong photosensitivity, and relatively low cost. However, their commercial application has been limited by their wide bandgaps, inability to absorb visible light, fast electron/hole recombination, and limited recyclability since the nanomaterial is difficult to recover. Researchers have developed several strategies to overcome these limitations. Chief amongst these is the coupling of different semi-conductor materials to produce heterojunction nanocomposite materials, which are both visible-light-active and easily recoverable. This review focuses on the advances made in the development of magnetic ferrite-based titanium oxide and zinc oxide nanocomposites. The physical and magnetic properties of the most widely used ferrite compounds are discussed. The spinel structured material had superior catalytic and magnetic performance when coupled to TiO2 and ZnO. An assessment of the range of synthesis methods is also presented. A comprehensive review of the photocatalytic degradation of various priority organic pollutants using the ferrite-based nanocomposites revealed that degradation efficiency and magnetic recovery potential are dependent on factors such as the chemical composition of the heterojunction material, synthesis method, irradiation source, and structure of pollutant. It should be noted that very few studies have gone beyond the degradation efficiency studies. Very little information is available on the extent of mineralization and the subsequent formation of intermediate compounds when these composite catalysts are used. Additionally, potential degradation mechanisms have not been adequately reported.

Green Synthesis of Metal and Metal Oxide Nanoparticles: Principles of Green Chemistry and Raw Materials

Increased request for metal and metal oxide nanoparticles nanoparticles has led to their large-scale production using high-energy methods with various toxic solvents. This cause environmental contamination, thus eco-friendly “green” synthesis methods has become necessary. An alternative way to synthesize metal nanoparticles includes using bioresources, such as plants and plant products, bacteria, fungi, yeast, algae, etc. “Green” synthesis has low toxicity, is safe for human health and environment compared to other methods, meaning it is the best approach for obtaining metal and metal oxide nanoparticles. This review reveals 12 principles of “green” chemistry and examples of biological components suitable for “green” synthesis, as well as modern scientific research of eco-friendly synthesis methods of magnetic and metal nanoparticles. Particularly, using extracts of green tea, fruits, roots, leaves, etc., to obtain Fe3O4 NPs. The various precursors as egg white (albumen), leaf and fruit extracts, etc., can be used for the „green” synthesis of spinel magnetic NPs. “Green” nanoparticles are being widely used as antimicrobials, photocatalysts and adsorbents. “Green” magnetic nanoparticles demonstrate low toxicity and high biocompatibility, which allows for their biomedical application, especially for targeted drug delivery, contrast imaging and magnetic hyperthermia applications. The synthesis of silver, gold, platinum and palladium nanoparticles using extracts from fungi, red algae, fruits, etc., has been described.

Synthesis and characterization of TiO2 NPs by aqueous leaf extract of Coleus aromaticus and assess their antibacterial, larvicidal, and anticancer potential

The frequent applications of synthetic chemical insecticides and drugs create resistance among insects and microbes, creating a new threat to human and environmental welfare. This investigation focused on evaluating the possibilities of fabricating and characterizing the titanium dioxide nanoparticles (TiO₂ NPs) from titanium dioxide (TiO₂) through the aqueous leaf extract of Coleus aromaticus. Their biological applications were studied against the larvae of Aedes aegypti human pathogenic bacteria, and cancer cell line. The results revealed that the aqueous leaf extract had the metal reducing proficiency to produce nanoparticles from TiO₂. The synthesized TiO₂ NPs were initially confirmed by visible color changes and Ultraviolet-Visible Spectrophotometer analysis that showed a predominant peak at 332 nm. Furthermore, the nanocrystals, structural alignment, functional groups and elemental compositions were studied by following standard operating protocol in XRD (X-ray Powder Diffraction), FTIR (Fourier Transform Infrared Spectroscopy), TEM (Transmission Electron Microscopy), and EDX (Energy-Dispersive X-ray Spectroscopy) techniques, respectively. The results attained from these techniques confirmed that the plant mediated and fabricated particles were in the nanoscale range (12-33 nm) with a hexagonal shape. The synthesized TiO₂ NPs had an outstanding (1000 μg mL^-1) larvicidal activity against the four stages of instars larvae of Ae. aegypti at 1000 μg mL^-1. It also had an excellent antibacterial potential against E. faecalis (33 mm), followed by S. boydii (30 mm) at 30 mg L^-1 concentration. The green fabricated TiO₂ NPs had a fabulous (92.37%) cytotoxic activity on the HeLa cell line at 100 μg mL^-1 dosage within one day of exposure. The entire results concluded that the C. aromaticus mediated TiO₂ NPs have excellent biological applications and thus, could be considered for the welfare of human beings.

Design and Catalytic Behaviour of Hosted in Activated Carbon Foam CoxZn1−xFe2O4 Ferrites

Carbon foams with different surface functionality and tailored texture characteristics were prepared from mixtures containing coal tar pitch and furfural in different proportions. The obtained materials were used as a host matrix for the preparation of zinc- and cobalt-mixed ferrite nanoparticles. The texture, morphology, phase composition, and the related redox and catalytic properties of the obtained composites were characterized by low-temperature nitrogen physisorption, XRD, SEM, HRTEM, FTIR, Mössbauer spectroscopy, TPR and catalytic decomposition of methanol to syngas. The impact of the carbon support on the formation of Co- and Zn-mixed ferrites was discussed in detail using KIT-6 silica-based modifications as reference samples. The catalytic behavior of the ferrites was considered in a complex relation to their composition, morphology, location in the porous matrix and metal ions distribution in the spinel sub-lattices. The higher amount of furfural in the carbon foam precursor promoted the formation of cobalt-rich, more accessible and highly active methanol decomposition to syngas spinel particles.

Antibacterial and antibiofilm activities of silver-decorated zinc ferrite nanoparticles synthesized by a gamma irradiation-coupled sol-gel method against some pathogenic bacteria from medical operating room surfaces

This work aimed at the gamma irradiation-assisted synthesis of silver (Ag)-decorated ZnFe2O4 (ZFO) ferrite nanoparticles (NPs), which were tested for their antibacterial and antibiofilm activities against some pathogenic bacteria from medical operating room surfaces. The prepared Ag-decorated ZFO NPs were characterized via XRD, SEM, EDX, elemental mapping, and FTIR analysis. The antibacterial potential was tested as ZOI and MIC, while antibiofilm activity was estimated by the tube method. The growth curve assay, the effect of UV on the antimicrobial activity, and cell membrane leakage were evaluated, and the antibacterial reaction mechanism was investigated by SEM/EDX analysis. The XRD and FTIR results confirmed the successful preparation of Ag-decorated ZFO NPs. Antibacterial results revealed that the most potent decorated sample was Ag0.75@ZFO NPs, recording the most significant inhibition zone against Staphylococcus vitulinus (24.67 ± 0.577 mm) and low MIC (0.097 μg mL-1) against S. vitulinus. The antibiofilm activity of Ag0.75@ZFO NPs was the highest, recorded as 97.3% for S. aureus and 95.25% for Enterococcus columbae. In the case of UV exposure, bacterial growth reached the lowest grade. Finally, it was seen that the amount of cellular protein released from bacterial cells is directly proportional to the concentration of Ag0.75@ZFO NPs, which clearly explains the formation of pits in the cell membrane. The synthesized nanocomposites may find an application after mixing with operating room paints to reduce the harmful effect of pathogenic microbes and, therefore, eliminate bacterial contamination.

Recent Advances in Synthesis and Applications of MFe2O4 (M = Co, Cu, Mn, Ni, Zn) Nanoparticles

In the last decade, research on the synthesis and characterization of nanosized ferrites has highly increased and a wide range of new applications for these materials have been identified. The ability to tailor the structure, chemical, optical, magnetic, and electrical properties of ferrites by selecting the synthesis parameters further enhanced their widespread use. The paper reviews the synthesis methods and applications of MFe₂O₄ (M = Co, Cu, Mn, Ni, Zn) nanoparticles, with emphasis on the advantages and disadvantages of each synthesis route and main applications. Along with the conventional methods like sol-gel, thermal decomposition, combustion, co-precipitation, hydrothermal, and solid-state synthesis, several unconventional methods, like sonochemical, microwave assisted combustion, spray pyrolysis, spray drying, laser pyrolysis, microemulsion, reverse micelle, and biosynthesis, are also presented. MFe₂O₄ (M = Co, Cu, Mn, Ni, Zn) nanosized ferrites present good magnetic (high coercivity, high anisotropy, high Curie temperature, moderate saturation magnetization), electrical (high electrical resistance, low eddy current losses), mechanical (significant mechanical hardness), and chemical (chemical stability, rich redox chemistry) properties that make them suitable for potential applications in the field of magnetic and dielectric materials, photoluminescence, catalysis, photocatalysis, water decontamination, pigments, corrosion protection, sensors, antimicrobial agents, and biomedicine.

Mesoporous ferromagnetic manganese ferrite nanoparticles for enhanced visible light mineralization of azoic dye into nontoxic by-products

In this study, a one pot facile synthesis of ferromagnetic manganese ferrite nanoparticles (MnFe₂O₄) was carried out using chemical co-precipitation method for mineralization of azo dye (Congo red (CR)) in aqueous solution under visible light irradiation. The synthesized MnFe₂O₄ nanoparticles were highly crystalline and showed face-centred cubic (FCC) structure with average particle size of 58 ± 4 nm. The BET analysis of the MnFe₂O₄ nanoparticles revealed the mesoporous distribution of material with high surface area can provide large electro active sites and short diffusion paths for the transport of ions which plays a vital role in the photocatalytic degradation of CR. The point of zero charge (pH_PZC) was observed to be 6.7 indicating favourable condition for material-anionic dye interaction. The XPS studies revealed that the large amounts of oxygen vacancies were produced due to the defects in the lattice oxygen. The MnFe₂O₄ nanoparticles mineralised 98.3 ± 0.2% of 50 mg/L CR within 30 min when tested in photocatalytic reactor under 565 nm. The particles were recoverable under the influence of an external magnet after the photocatalytic reaction and were reusable. The recovered nanoparticles showed 96% of CR degradation efficiency even after five cycles of reuse. The by-product analysis with GC-MS indicated mineralization of CR into simple alcohols and acids. The aqueous solution containing mineralised CR was nontoxic to Trigonella foenumgraecum and Vigna mungo seeds and favoured increased germination, plumule and radicle length when compared to untreated CR.

Metal ferrite incorporated polysulfone thin-film nanocomposite membranes for wastewater treatment

Effluents from food, fermentation, and sugar industries contain a large quantity of glucose which has to be removed to limit the chemical oxygen demand (COD) of the water discharged. This work proposes novel thin-film nanocomposite (TFN) membranes incorporated with MgFe₂O₄ and ZnFe₂O₄ nanoparticles to address this concern. The nanoparticles synthesized by the sol-gel method was extensively characterized and then incorporated into the active polyamide layer of the thin-film composite polysulfone membranes. The change in membrane morphology, wettability, chemical structure, and mechanical strength with the incorporation of nanoparticles was studied in detail. Membranes with 0.005 wt.% MgFe₂O₄ nanoparticle exhibited highest glucose rejection (96.52 ± 2.35%) at 10 bar, 25 °C, and sufficiently high pure water flux (50.54 ± 1.92 L/m²h). This membrane also displayed 69.1 ± 5.12% salt rejection when challenged with 2000 ppm synthetic NaCl solution.

Cashew gum as a sol-gel precursor for green synthesis of nanostructured Ni and Co ferrites

The aim of this work consists in the use of cashew gum (Anacardium occidentale), a naturally occurring tropical specie from the Brazilian northeastern coast, for the synthesis of CoFe₂O₄ (CF) and NiFe₂O₄ (NF) nanoparticles. The structural, morphological and vibrational properties of nanoparticles were characterized by analytical and spectroscopic techniques such as X-ray diffraction (XRD), FTIR, Raman spectroscopy, TEM, SAED and TG. Magnetic properties were investigated through Mössbauer spectroscopy and DC magnetometry. The XRD results showed single phase nanoparticles with space group Fd-3m and crystallite size of 7.4 and 6.0 for CF and NF, respectively. TEM images showed agglomerated particles with mode sizes of 5.0 and 6.5 nm for CF and NF. SAED confirmed the crystalline spinel structure. The TGA and FTIR showed the presence of a carbonaceous material in the samples. FTIR and Raman spectroscopy demonstrated vibrational modes characteristic of metal‑oxygen bonds in the tetrahedral and octahedral sites. Magnetization measurements showed that both samples are superparamagnetic at 300 K. The Mössbauer spectra at 90 K showed the presence of single-phase CF and NF.

Influence of Cu2+, Ni2+, and Zn2+ Ions Doping on the Structure, Morphology, and Magnetic Properties of Co-Ferrite Embedded in SiO2 Matrix Obtained by an Innovative Sol-Gel Route

This paper presents the synthesis of metal doped Co ferrites, M_0.2Co_0.8Fe₂O₄ (M = Cu²⁺, Ni²⁺, and Zn²⁺) embedded in SiO₂ matrix by an innovative sol-gel route. The structural and morphological characterization provided information about the crystalline phases, crystallite size, and the shape of the prepared ferrites. The thermal study depicted the thermal decomposition and stability of the obtained ferrites. X-ray diffraction indicated nanocrystalline ferrites with spinel structure and the lack of crystalline phase impurities, while Fourier transform infrared spectroscopy revealed the presence of functional groups in precursors and ferrite powders. The lattice parameters showed a gradual increase indicating a uniform distribution of divalent metal ions in the Co ferrite lattice. The crystallite size, magnetic moment, super-exchange and deflection of magnetic domain were influenced by the dopant metal ion. The room temperature magnetization indicated a ferromagnetic behavior of the ferrites annealed at 1000 °C and a superparamagnetic behavior of the ferrites annealed at 700 °C.