Generation of purified nitric oxide from liquid N2O4 for the treatment of pulmonary hypertension in hypoxemic swine

A novel, cassette-based nitric oxide delivery system with an advanced feedback control algorithm accurately delivers nitric oxide via the anesthesia machine independent of fresh gas flow rate and volatile anesthetic agent

Nitric oxide (NO), a selective pulmonary vasodilator, can be delivered via conventional ICU and anesthesia machine ventilators. Anesthesia machines are designed for rebreathing of circulating gases, reducing volatile anesthetic agent quantity used. Current cylinder- and ionizing-based NO delivery technologies use breathing circuit flow to determine NO delivery and do not account for recirculated gases; therefore, they cannot accurately dose NO at FGF below patient minute ventilation (MV). A novel, cassette-based NO delivery system (GENOSYL® DS, Vero Biotech Inc.) uses measured NO concentration in the breathing circuit as an input to an advanced feedback control algorithm, providing accurate NO delivery regardless of FGF and recirculation of gases. This study evaluated GENOSYL® DS accuracy with different anesthesia machines, ventilation parameters, FGFs, and volatile anesthetics. GENOSYL® DS was tested with GE Aisys and Dräger Fabius anesthesia machines to determine NO dose accuracy with FGF < patient MV, and with a Getinge Flow-i anesthesia machine to determine NO dose accuracy when delivering various volatile anesthetic agents. Neonatal and adult mechanical ventilation parameters and circuits were used. GENOSYL® DS maintained accurate NO delivery with all three anesthesia machines, at low FGF with recirculation of gases, and with all volatile anesthetic agents at different concentrations. Measured NO2 levels remained acceptable at ≤ 1 ppm with set NO dose ≤ 40 ppm. GENOSYL® DS, with its advanced feedback control algorithm, is the only NO delivery system capable of accurately dosing NO with anesthesia machines with rebreathing ventilation parameters (FGF < MV) regardless of anesthetic agent.

Mechanistic analysis of the photolytic decomposition of solid-state S-nitroso-N-acetylpenicillamine

S-Nitroso-N-acetylpenicillamine (SNAP) is among the most common nitric oxide (NO)-donor molecules and its solid-state photolytic decomposition has potential for inhaled nitric oxide (iNO) therapy. The photochemical NO release kinetics and mechanism were investigated by exposing solid-state SNAP to a narrow-band LED as a function of nominal wavelength and intensity of incident light. The photolytic efficiency, decomposition products, and the photolytic pathways of the SNAP were examined. The maximum light penetration depth through the solid layer of SNAP was determined by an optical microscope and found to be within 100-200 μm, depending on the wavelength of light. The photolysis of solid-state SNAP to generate NO along with the stable thiyl (RS·) radical was confirmed using Electron Spin Resonance (ESR) spectroscopy. The fate of the RS· radical in the solid phase was studied both in the presence and absence of O2 using NMR, IR, ESR, and UPLC-MS. The changes in the morphology of SNAP due to its photolysis were examined using PXRD and SEM. The stable thiyl radical formed from the photolysis of solid SNAP was found to be reactive with another adjacent thiyl radical to form a disulfide (RSSR) or with oxygen to form various sulfonyl and sulfonyl peroxyl radicals {RS(O)xO·, x = 0 to 7}. However, the thiyl radical did not recombine with NO to reform the SNAP. From the PXRD data, it was found that the SNAP loses its crystallinity by generating the NO after photolysis. The initial release of NO during photolysis was increased with increased intensity of light, whereas the maximum light penetration depth was unaffected by light intensity. The knowledge gained about the photochemical reactions of SNAP may provide important insight in designing portable photoinduced NO-releasing devices for iNO therapy.

Development of nitric oxide generators to produce high-dose nitric oxide for inhalation therapy

BACKGROUND

Several nitric oxide (NO) generating devices have been developed to deliver NO between 1 part per million (ppm) and 80 ppm. Although inhalation of high-dose NO may exert antimicrobial effects, the feasibility and safety of producing high-dose (more than 100 ppm) NO remains to be established. In the current study, we designed, developed, and tested three high-dose NO generating devices.

METHODS

We constructed three NO generating devices: a double spark plug NO generator, a high-pressure single spark plug NO generator, and a gliding arc NO generator. The NO and NO2 concentrations were measured at different gas flows and under various atmospheric pressures. The double spark plug NO generator was designed to deliver gas through an oxygenator and mixing with pure oxygen. The high-pressure and gliding arc NO generators were used to deliver gas through a ventilator into artificial lungs to mimic delivering high-dose NO in the clinical settings. The energy consumption was measured and compared among the three NO generators.

RESULTS

The double spark plug NO generator produced 200 ± 2 ppm (mean ± SD) of NO at gas flow of 8 L/min (or 320 ± 3 ppm at gas flow of 5 L/min) with electrode gap of 3 mm. The nitrogen dioxide (NO2) levels were below 3.0 ± 0.1 ppm when mixing with various volumes of pure oxygen. The addition of a second generator increased the delivered NO from 80 (with one spark plug) to 200 ppm. With the high-pressure chamber, the NO concentration reached 407 ± 3 ppm with continuous air flow at 5 L/min when employing the 3 mm electrode gap under 2.0 atmospheric pressure (ATA). When compared to 1 ATA, NO production was increased 22% at 1.5 ATA and 34% at 2 ATA. The NO level was 180 ± 1 ppm when connecting the device to a ventilator with a constant inspiratory airflow of 15 L/min, and NO2 levels were below 1 (0.93 ± 0.02) ppm. The gliding arc NO generator produced up to 180 ± 4 ppm of NO when connecting the device to a ventilator, and the NO2 level was below 1 (0.91 ± 0.02) ppm in all testing conditions. The gliding arc device required more power (in watts) to generate the same concentrations of NO when compared to double spark plug or high-pressure NO generators.

CONCLUSIONS

Our results demonstrated that it is feasible to enhance NO production (more than 100 ppm) while maintaining NO2 level relatively low (less than 3 ppm) with the three recently developed NO generating devices. Future studies might include these novel designs to deliver high doses of inhaled NO as an antimicrobial used to treat upper and lower respiratory tract infections.

Disposable Nitric Oxide Generator Based on a Structurally Deformed Nitrite-Type Layered Double Hydroxide

The inhalation of nitric oxide (NO), which acts as a selective vasodilator of pulmonary blood vessels, is an established medical treatment. However, its wide adoption has been limited by the lack of a convenient delivery technique of this unstable gas. Here we report that a solid mixture of FeIISO4·7H2O and a layered double hydroxide (LDH) containing nitrite (NO2-) in the interlayer spaces (NLDH) stably generates NO at a therapeutic level (∼40 ppm over 12 h from freshly mixed solids; ∼80 ppm for 5-10 h from premixed solids) under air flow (0.25 L min-1) if the NLDH has been prepared by using a reconstruction method. Mg/Al-type LDH was calcined at 550 °C to remove interlayer CO32- and then treated with NaNO2 in water to reconstruct the NLDH. This one-pot, organic solvent-free process can be performed at large scales and is suitable for mass production. Humid air promotes anion exchange between NO2- and SO42- in the solid mixture, resulting in persistent interactions of NO2- and Fe2+, generating NO. In contrast to the previously reported NLDH prepared using an anion-exchange method, the reconstructed NLDH exhibits stable and persistent generation of NO because of partial deformation of the layered structures (e.g., particle aggregation, reduced crystallinity, and enhanced basicity). Degradation of the solid mixture is suppressed under dry conditions, so that a portable cartridge column that is readily available as an NO source for emergency situations can be prepared. This work demonstrates that the interlayer nanospace of LDH serves as a reaction mediator for excellent controllability of solid-state reactions. This inexpensive and disposable NO generator will facilitate NO inhalation therapy in developing countries and nonhospital locations.

Clinical use of inhaled nitric oxide: Local and systemic applications

Upon the FDA approval for inhaled nitric oxide (iNO) in 1999 to treat persistent pulmonary hypertension in neonates, iNO has proven to be a beneficial therapeutic in multiple diseases. We aim to review applications of iNO that have modeled its protective and therapeutic attributes, as well as highlight preliminary studies that could allude to future avenues of use. Numerous publications have reported specific incidences where iNO therapy has proved advantageous, while some applications have potential after further validation. Establishing guidelines on dosing, duration, and defined clinical uses are crucial for the future of iNO. Delivery of iNO has been controlled by a sole distributor, and comes with high cost, and lack of portability. A shift in patents has allowed for new designs for iNO device synthesis, with many new developments of iNO medical devices that will likely change the future of iNO in a medical setting.

Feedback-controlled photolytic gas phase nitric oxide delivery from S-nitrosothiol-doped silicone rubber films

Constant therapeutic gas phase nitric oxide (NO) delivery is achieved from S-nitrosothiol (RSNO) type NO donor doped silicone rubber films using feedback-controlled photolysis. For photo-release of the NO gas, the intensity of the LED light source is controlled via a PID (proportional-integral-derivative) controller implemented on a microcontroller. The NO concentration within the emitted gas phase is monitored continuously with a commercial amperometric NO gas sensor. NO release was accurately adjustable up to 10 ppm across a broad range of setpoints with response times of roughly 1 min or less. When NO is generated into an air recipient stream, lower NO yields and a comparable level of toxic nitrogen dioxide (NO2) formation is observed. However, NO gas generated into an N2 recipient gas stream can be blended into pure O2 with very low NO2 formation. Following scale-up, this technology could be used for point-of-care gas phase NO generation as an alternative for currently used gas cylinder technology for treatment of health conditions where inhaled NO is beneficial, such as pulmonary hypertension, hypoxemia, and cystic fibrosis.

Inhaled nitric oxide

Nitric oxide (NO) is a gas that induces relaxation of smooth muscle cells in the vasculature. Because NO reacts with oxyhaemoglobin with high affinity, the gas is rapidly scavenged by oxyhaemoglobin in red blood cells and the vasodilating effects of inhaled NO are limited to ventilated regions in the lung. NO therefore has the unique ability to induce pulmonary vasodilatation specifically in the portions of the lung with adequate ventilation, thereby improving oxygenation of blood and decreasing intrapulmonary right to left shunting. Inhaled NO is used to treat a spectrum of cardiopulmonary conditions, including pulmonary hypertension in children and adults. However, the widespread use of inhaled NO is limited by logistical and financial barriers. We have designed, developed and tested a simple and economic NO generation device, which uses pulsed electrical discharges in air to produce therapeutic levels of NO that can be used for inhalation therapy. LINKED ARTICLES: This article is part of a themed section on Nitric Oxide 20 Years from the 1998 Nobel Prize. To view the other articles in this section visit http://onlinelibrary.wiley.com/doi/10.1111/bph.v176.2/issuetoc.

Development of a portable mini-generator to safely produce nitric oxide for the treatment of infants with pulmonary hypertension

OBJECTIVES

To test the safety of a novel miniaturized device that produces nitric oxide (NO) from air by pulsed electrical discharge, and to demonstrate that the generated NO can be used to vasodilate the pulmonary vasculature in rabbits with chemically-induced pulmonary hypertension.

STUDY DESIGN

A miniature NO (mini-NO) generator was tested for its ability to produce therapeutic levels (20-80 parts per million (ppm)) of NO, while removing potentially toxic gases and metal particles. We studied healthy 6-month-old New Zealand rabbits weighing 3.4 ± 0.4 kg (mean ± SD, n = 8). Pulmonary hypertension was induced by chemically increasing right ventricular systolic pressure to 28-30 mmHg. The mini-NO generator was placed near the endotracheal tube. Production of NO was triggered by a pediatric airway flowmeter during the first 0.5 s of inspiration.

RESULTS

In rabbits with acute pulmonary hypertension, the mini-NO generator produced sufficient NO to induce pulmonary vasodilation. Potentially toxic nitrogen dioxide (NO₂) and ozone (O₃) were removed by the Ca(OH)₂ scavenger. Metallic particles, released from the electrodes by the electric plasma, were removed by a 0.22 μm filter. While producing 40 ppm NO, the mini-NO generator was cooled by a flow of air (70 ml/min) and the external temperature of the housing did not exceed 31 °C.

CONCLUSIONS

The mini-NO generator safely produced therapeutic levels of NO from air. The mini-NO generator is an effective and economical approach to producing NO for treating neonatal pulmonary hypertension and will increase the accessibility and therapeutic uses of life-saving NO therapy worldwide.

Pulmonary Delivery of Therapeutic and Diagnostic Gases

The 21st Congress for the International Society for Aerosols in Medicine included, for the first time, a session on Pulmonary Delivery of Therapeutic and Diagnostic Gases. The rationale for such a session within ISAM is that the pulmonary delivery of gaseous drugs in many cases targets the same therapeutic areas as aerosol drug delivery, and is in many scientific and technical aspects similar to aerosol drug delivery. This article serves as a report on the recent ISAM congress session providing a synopsis of each of the presentations. The topics covered are the conception, testing, and development of the use of nitric oxide to treat pulmonary hypertension; the use of realistic adult nasal replicas to evaluate the performance of pulsed oxygen delivery devices; an overview of several diagnostic gas modalities; and the use of inhaled oxygen as a proton magnetic resonance imaging (MRI) contrast agent for imaging temporal changes in the distribution of specific ventilation during recovery from bronchoconstriction. Themes common to these diverse applications of inhaled gases in medicine are discussed, along with future perspectives on development of therapeutic and diagnostic gases.

Detection and removal of impurities in nitric oxide generated from air by pulsed electrical discharge

Inhalation of nitric oxide (NO) produces selective pulmonary vasodilation without dilating the systemic circulation. However, the current NO/N₂ cylinder delivery system is cumbersome and expensive. We developed a lightweight, portable, and economical device to generate NO from air by pulsed electrical discharge. The objective of this study was to investigate and optimize the purity and safety of NO generated by this device. By using low temperature streamer discharges in the plasma generator, we produced therapeutic levels of NO with very low levels of nitrogen dioxide (NO₂) and ozone. Despite the low temperature, spark generation eroded the surface of the electrodes, contaminating the gas stream with metal particles. During prolonged NO generation there was gradual loss of the iridium high-voltage tip (-90 μg/day) and the platinum-nickel ground electrode (-55 μg/day). Metal particles released from the electrodes were trapped by a high-efficiency particulate air (HEPA) filter. Quadrupole mass spectroscopy measurements of effluent gas during plasma NO generation showed that a single HEPA filter removed all of the metal particles. Mice were exposed to breathing 50 parts per million of electrically generated NO in air for 28 days with only a scavenger and no HEPA filter; the mice did not develop pulmonary inflammation or structural changes and iridium and platinum particles were not detected in the lungs of these mice. In conclusion, an electric plasma generator produced therapeutic levels of NO from air; scavenging and filtration effectively eliminated metallic impurities from the effluent gas.

Nitrogen dioxide reducing ascorbic acid technologies in the ventilator circuit leads to uniform NO concentration during inspiration

Conventional inhaled NO systems deliver NO by synchronized injection or continuous NO flow in the ventilator circuitry. Such methods can lead to variable concentrations during inspiration that may differ from desired dosing. NO concentrations in these systems are generally monitored through electrochemical methods that are too slow to capture this nuance and potential dosing error. A novel technology that reduces NO2 into NO via low-resistance ascorbic-acid cartridges just prior to inhalation has recently been described. The gas volume of these cartridges may enhance gas mixing and reduce dosing inconsistency throughout inhalation. The impact of the ascorbic-acid cartridge technology on NO concentration during inspiration was characterized through rapid chemiluminescence detection during volume control ventilation, pressure control ventilation, synchronized intermittent mandatory ventilation and continuous positive airway pressure using an in vitro lung model configured to simulate the complete uptake of NO. Two ascorbic acid cartridges in series provided uniform and consistent dosing during inspiration during all modes of ventilation. The use of one cartridge showed variable inspiratory concentration of NO at the largest tidal volumes, whereas the use of no ascorbic acid cartridge led to highly inconsistent NO inspiratory waveforms. The use of ascorbic acid cartridges also decreased breath-to-breath variation in SIMV and CPAP ventilation. The ascorbic-acid cartridges, which are designed to convert NO2 (either as substrate or resulting from NO oxidation during injection) into NO, also provide the benefit of minimizing the variation of inhaled NO concentration during inspiration. It is expected that the implementation of this method will lead to more consistent and predictable dosing.

Inhaled Nitric Oxide Augments Left Ventricular Assist Device Capacity by Ameliorating Secondary Right Ventricular Failure

Clinical right ventricular (RV) impairment can occur with left ventricular assist device (LVAD) use, thereby compromising the therapeutic effectiveness. The underlying mechanism of this RV failure may be related to induced abnormalities of septal wall motion, RV distension and ischemia, decreased LV filling, and aberrations of LVAD flow. Inhaled nitric oxide (NO), a potent pulmonary vasodilator, may reduce RV afterload, and thereby increase LV filling, LVAD flow, and cardiac output (CO). To investigate the mechanisms associated with LVAD-induced RV dysfunction and its treatment, we created a swine model of hypoxia-induced pulmonary hypertension and acute LVAD-induced RV failure and assessed the physiological effects of NO. Increased LVAD speed resulted in linear increases in LVAD flow until pulse pressure narrowed. Higher speeds induced flow instability, LV collapse, a precipitous fall of both LVAD flow and CO. Nitric oxide (20 ppm) treatment significantly increased the maximal achievable LVAD speed, LVAD flow, CO, and LV diameter. Nitric oxide resulted in decreased pulmonary vascular resistance and RV distension, increased RV ejection, promoted LV filling and improved LVAD performance. Inhaled NO may thus have broad utility for the management of biventricular disease managed by LVAD implantation through the effects of NO on LV and RV wall dynamics.

Producing nitric oxide by pulsed electrical discharge in air for portable inhalation therapy

Inhalation of nitric oxide (NO) produces selective pulmonary vasodilation and is an effective therapy for treating pulmonary hypertension in adults and children. In the United States, the average cost of 5 days of inhaled NO for persistent pulmonary hypertension of the newborn is about $14,000. NO therapy involves gas cylinders and distribution, a complex delivery device, gas monitoring and calibration equipment, and a trained respiratory therapy staff. The objective of this study was to develop a lightweight, portable device to serve as a simple and economical method of producing pure NO from air for bedside or portable use. Two NO generators were designed and tested: an offline NO generator and an inline NO generator placed directly within the inspiratory line. Both generators use pulsed electrical discharges to produce therapeutic range NO (5 to 80 parts per million) at gas flow rates of 0.5 to 5 liters/min. NO was produced from air, as well as gas mixtures containing up to 90% O2 and 10% N2. Potentially toxic gases produced in the plasma, including nitrogen dioxide (NO2) and ozone (O3), were removed using a calcium hydroxide scavenger. An iridium spark electrode produced the lowest ratio of NO2/NO. In lambs with acute pulmonary hypertension, breathing electrically generated NO produced pulmonary vasodilation and reduced pulmonary arterial pressure and pulmonary vascular resistance index. In conclusion, electrical plasma NO generation produces therapeutic levels of NO from air. After scavenging to remove NO2 and O3 and filtration to remove particles, electrically produced NO can provide safe and effective treatment of pulmonary hypertension.