Fabricated copper catalyst on biochar nanoparticles for the synthesis of tetrazoles as antimicrobial agents

Renewable Carbonaceous Materials from Biomass in Catalytic Processes: A Review

This review paper delves into the diverse ways in which carbonaceous resources, sourced from renewable and sustainable origins, can be used in catalytic processes. Renewable carbonaceous materials that come from biomass-derived and waste feedstocks are key to developing more sustainable processes by replacing traditional carbon-based materials. By examining the potential of these renewable carbonaceous materials, this review aims to shed light on their significance in fostering environmentally conscious and sustainable practices within the realm of catalysis. The more important applications identified are biofuel production, tar removal, chemical production, photocatalytic systems, microbial fuel cell electrodes, and oxidation applications. Regarding biofuel production, biochar-supported catalysts have proved to be able to achieve biodiesel production with yields exceeding 70%. Furthermore, hydrochars and activated carbons derived from diverse biomass sources have demonstrated significant tar removal efficiency. For instance, rice husk char exhibited an increased BET surface area from 2.2 m2/g to 141 m2/g after pyrolysis at 600 °C, showcasing its effectiveness in adsorbing phenol and light aromatic hydrocarbons. Concerning chemical production and the oxidation of alcohols, the influence of biochar quantity and pre-calcination temperature on catalytic performance has been proven, achieving selectivity toward benzaldehyde exceeding 70%.

Preparation of magnetic biochar functionalized by polyvinyl imidazole and palladium nanoparticles for the catalysis of nitroarenes hydrogenation and Sonogashira reaction

Catalysts are essential materials in biotechnology, medicine, industry, and chemistry. On the other hand, recycling and using waste materials is important in economic efficiency and green chemistry. Thus, biochar was prepared from the stem and roots of the Spear Thistle to recover waste. After magnetizing the biochar, its surface was modified with polyvinyl imidazole. Finally, this modified biochar was decorated with Pd nanoparticles and used as a selective and recyclable nanocatalyst in the hydrogenation of nitroarenes and the Sonogashira reaction. The structure of this organic-inorganic nanocatalyst has been characterized by FESEM-EDS, XRD, FT-IR, TEM, and VSM techniques. In the hydrogenation reaction with the amount of 30 mg of nanocatalyst, the temperature of 50 °C in the water solvent, the reaction efficiency reached 99% for 30 min. In addition, under optimal conditions for the Sonogashira reaction: 1.0 mmol iodobenzene, 1.2 mmol phenylacetylene, 20 mg MBC-PVIm/Pd, 2 mmol K2CO3 in H2O at 50 C for 15 min, the reaction efficiency reached 95%. The recyclability of magnetic nanocatalysts was investigated and recognized this nanocatalyst can be used several times without notable loss of its activity.

Copper-decorated core-shell structured ordered mesoporous containing cobalt ferrite nanoparticles as high-performance heterogeneous catalyst toward synthesis of tetrazole

The present work describes the synthesis of copper immobilization on CoFe2O4/MCM-41 as a catalyst, which is created by attaching copper and ligand (N-phenyl anthranilic acid (PA)) on the surface of CoFe2O4/MCM-41 (CoFe2O4/MCM-41/PA/Cu). The synthesized CoFe2O4/MCM-41 support and immobilized copper were identified by FTIR, TEM, VSM, SEM XRD, and nitrogen adsorption-desorption analysis. The results showed that MCM-41 silica was coated with magnetite nanoparticles and copper was successfully immobilized on this structure. The catalytic performance of synthesized catalyst was tested in the synthesis of tetrazole. It was shown that the solid catalyst exhibited a strong magnetic response and showed good catalytic activity in the synthesis of tetrazole. The catalytic test showed that copper supported on CoFe2O4/MCM-41 hybrid showed much better catalytic activity than copper supported on CoFe2O4, indicating that MCM-41 plays an important role in CoFe2O4/MCM-41 hybrid for the synthesis of tetrazole. Separation of the solid catalyst from the reaction mixture was easily performed by external magnetism without apparent mass loss. And the catalyst could be reused six times for the synthesis of heterogeneous tetrazole.

Recent advances in antifungal drug development targeting lanosterol 14α-demethylase (CYP51): A comprehensive review with structural and molecular insights

Fungal infections are posing serious threat to healthcare system due to emerging resistance among available antifungal agents. Among available antifungal agents in clinical practice, azoles (diazole, 1,2,4-triazole and tetrazole) remained most effective and widely prescribed antifungal agents. Now their associated side effects and emerging resistance pattern raised a need of new and potent antifungal agents. Lanosterol 14α-demethylase (CYP51) is responsible for the oxidative removal of 14α-methyl group of sterol precursors lanosterol and 24(28)-methylene-24,25-dihydrolanosterol in ergosterol biosynthesis hence an essential component of fungal life cycle and prominent target for antifungal drug development. This review will shed light on various azole- as well as non-azoles-based derivatives as potential antifungal agents that target fungal CYP51. Review will provide deep insight about structure activity relationship, pharmacological outcomes, and interactions of derivatives with CYP51 at molecular level. It will help medicinal chemists working on antifungal development in designing more rational, potent, and safer antifungal agents by targeting fungal CYP51 for tackling emerging antifungal drug resistance.

Determination of Fluoxetine in Weight Loss Herbal Medicine Using an Electrochemical Sensor Based on rGO-CuNPs

The rising popularity of herbal medicine as a weight loss remedy, fueled by misleading propaganda, raises concerns about the manufacturing processes and potential inclusion of controlled substances such as fluoxetine (FLU). The objective of this work is to develop and evaluate the performance of an electrochemical device by modifying a glassy carbon electrode (GC) with a nanocomposite based on reduced graphene oxide (rGO) and copper nanoparticles (CuNPs) for detecting FLU in manipulated herbal medicines. Scanning electron microscopy (FEG-SEM) and cyclic voltammetry (CV) were applied for morphological and electrochemical characterization and analysis of the composite's electrochemical behavior. Under optimized conditions, the proposed sensor successfully detected FLU within the range of 0.6 to 1.6 µmol L-1, showing a limit of detection (LOD) of 0.14 µmol L-1. To determine the presence of FLU in herbal samples, known amounts of the analytical standard were added to the sample, and the analyses were performed using the standard addition method, yielding recoveries between -2.13 and 2.0%.

Immobilization of Ni(ii) complex on the surface of mesoporous modified-KIT-6 as a new, reusable and highly efficient nanocatalyst for the synthesis of tetrazole and pyranopyrazole derivatives

In this paper, KIT-6@SMTU@Ni was successfully synthesized via a new method of Ni(ii) complex stabilization on modified mesoporous KIT-6, as a novel and green heterogeneous catalyst. The obtained catalyst (KIT-6@SMTU@Ni) was characterized using Fourier transform infrared spectroscopy (FT-IR), Brunauer-Emmett-Teller (BET) calculation, X-ray diffraction (XRD), atomic absorption spectroscopy (AAS), energy-dispersive X-ray spectroscopy (EDS), X-ray mapping, thermogravimetric analysis (TGA) techniques and scanning electron microscopy (SEM). After complete characterization of the catalyst, it was successfully used for the synthesis of 5-substituted 1H-tetrazoles and pyranopyrazoles. Moreover, tetrazoles were synthesized from benzonitrile derivatives and sodium azide (NaN₃). All tetrazole products were synthesized with high TON, TOF and excellent yields (88-98%) in a reasonable time (0.13-8 h), demonstrating the efficiency and practicality of the KIT-6@SMTU@Ni catalyst. Furthermore, pyranopyrazoles were prepared through the condensation reaction of benzaldehyde derivatives with malononitrile, hydrazine hydrate and ethyl acetoacetate with high TON, TOF and excellent yields (87-98%) at appropriate times (2-10.5 h). KIT-6@SMTU@Ni could be reused for five runs without any re-activation. Significantly, this plotted protocol has prominent benefits, such as applying green solvents, the use of commercially available and low-cost materials, excellent separation and reusability of the catalyst, short reaction time, high yield of products and a facile work-up.

A new samarium complex of 1,3-bis(pyridin-3-ylmethyl)thiourea on boehmite nanoparticles as a practical and recyclable nanocatalyst for the selective synthesis of tetrazoles

Boehmite is a natural and environmentally friendly compound. Herein boehmite nanoparticles were primarily synthesized and, then, their surface were modified via 3-choloropropyltrimtoxysilane (CPTMS). Afterwards, a new samarium complex was stabilized on the surface of the modified boehmite nanoparticles (Sm-bis(PYT)@boehmite). The obtained nanoparticles were characterized using thermogravimetric analysis (TGA), energy dispersive X-ray spectroscopy (EDS), Brunauer-Emmett-Teller (BET), wavelength dispersive X-ray spectroscopy (WDX), scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FT-IR), Inductively coupled plasma mass spectrometry (ICP-MS), dynamic light scattering (DLS), and X-ray diffraction (XRD) pattern. Sm-bis(PYT)@boehmite was used as an environmentally friendly, efficient, and organic-inorganic hybrid nanocatalyst in the homoselective synthesis of tetrazoles in polyethylene glycol 400 (PEG-400) as a green solvent. Notably, Sm-bis(PYT)@boehmite is stable and has a heterogeneous nature. Thus, it can be reused for several runs without any re-activation.

Synthesis of tetrazoles catalyzed by a new and recoverable nanocatalyst of cobalt on modified boehmite NPs with 1,3-bis(pyridin-3-ylmethyl)thiourea

In the first part of this work, boehmite nanoparticles (BNPs) were synthesized from aqueous solutions of NaOH and Al(NO₃)₃·9H₂O. Then, the BNPs surface was modified using 3-choloropropyltrimtoxysilane (CPTMS) and then 1,3-bis(pyridin-3-ylmethyl)thiourea ((PYT)₂) was anchored on the surface of the modified BNPs (CPTMS@BNPs). In the final step, a complex of cobalt was stabilized on its surface (Co-(PYT)₂@BNPs). The final obtained nanoparticles were characterized by FT-IR spectra, TGA analysis, SEM imaging, WDX analysis, EDS analysis, and XRD patterns. In the second part, Co-(PYT)₂@BNPs were used as a highly efficient, retrievable, stable, and organic-inorganic hybrid nanocatalyst for the formation of organic heterocyclic compounds such as tetrazole derivatives. Co-(PYT)₂@BNPs as a novel nanocatalyst are stable and have a heterogeneous nature; therefore, they can be recovered and reused again for several consecutive runs without any re-activation.

Immobilized Cu(0) nanoparticles on montmorillonite-modified with benzalkonium chloride (MMT-BAC@Cu(0)): as an eco-friendly and proficient heterogeneous nano-catalyst for green synthesis of 5-substituted 1H-tetrazoles

In this study, Cu(0) nanoparticles supported on organo-modified montmorillonite with benzalkonium chloride (MMT-BAC@Cu(0)) were synthesized and used as an eco-friendly and green heterogeneous catalyst for the synthesis of 5-substituted 1H-tetrazoles in mild media. The structure of the catalyst was investigated using various techniques including XRD, EDX, ICP, TEM, FE-SEM, and FT-IR. The advantages of availability, low cost, non-toxicity, and biocompatibility of clay were our focus in synthesizing this nanoclay catalyst. The method's advantages include good to excellent product yields, mild conditions, easy work-up, short reaction times, and easy reuse of the nanocatalyst.

A Schiff base complex of lanthanum on modified MCM-41 as a reusable nanocatalyst in the homoselective synthesis of 5-substituted 1H-tetrazoles

In this work, mesoporous MCM-41 was modified by a new Schiff-base formed from the condensation of triethylenetatramine and 5-bromosalicylaldehyde. Then, it was used for the stabilization of lanthanum metal (La-Schiff base@MCM-41) as a homoselective, reusable, efficient and biocompatible catalyst in the synthesis of 5-substituted 1H-tetrazole derivatives. The synthesized tetrazoles were characterized using ¹H NMR and FT-IR spectroscopy and methods to measure their physical properties. La-Schiff base@MCM-41 was characterized by using various techniques such as ICP, CHN, XRD, TGA, BET, FT-IR spectroscopy, SEM, EDS and WDX. This catalyst has good stability and a heterogeneous nature, enabling it to be easily recovered and reused several times without significant loss in catalytic activity. This present strategy has important advantages such as utilizing PEG as a green solvent, short reaction times, excellent yields, easy recycling of the catalyst and pure separation of the products. The recovered La-Schiff base@MCM-41 catalyst was characterized by using FT-IR spectroscopy, SEM and AAS.

Preparation of Copper-Decorated Activated Carbon Derived from Platamus occidentalis Tree Fiber for Antimicrobial Applications

This study focuses on a greener approach to synthesizing activated carbon by carbonizing Platamus occidentalis tree fibers (TFSA) with 98% H₂SO₄ at 100 °C. The resulted TFSA was employed as an effective adsorbent for copper ions in aqueous media, yielding copper decorated TFSA (Cu@TFSA). The successful adsorption of copper onto the TFSA was proven through extensive characterization techniques. Herein, the TEM and XPS showed that copper nanoparticles were formed in situ on the TFSA surface, without the use of additional reducing and stabilizing agents nor thermal treatment. The surface areas of TFSA and Cu@TFSA were 0.0150 m²/g and 0.3109 m²/g, respectively. Applying the Cu@TFSA as an antimicrobial agent against Escherica coli ( E. coli) and Salmonella resulted in the potential mitigation of complex secondary pollutants from water and wastewater. The Cu@TFSA exhibited outstanding antimicrobial activity against E. coli and Salmonella in both synthetic and raw water samples. This demonstrated a complete growth inhibition observed within 120 min of exposure. The bacteria inactivation took place through the destruction of the bacteria cell wall and was confirmed by the AFM analysis technique. Cu@TFSA has the potential to be used in the water and wastewater treatment sector as antimicrobial agents.

Tetradentate copper complex supported on boehmite nanoparticles as an efficient and heterogeneous reusable nanocatalyst for the synthesis of diaryl ethers

In this work boehmite nanoparticles (BNPs) were prepared through addition of aqueous solution of NaOH to solution of Al(NO₃)₃·9H₂O. Then, the surface of BNPs was modified by (3-chloropropyl)trimethoxysilane (CPTMS) and further tetradentate ligand (MP-bis(AMP)) was anchored on its surface. At final step, a tetradentate organometallic complex of copper was stabilized on the surface of modified BNPs (Cu(II)-MP-bis(AMP)@boehmite). These obtained nanoparticles were characterized using SEM imaging, WDX, EDS, AAS and TGA analysis, BET method, FT-IR spectroscopy, and XRD pattern. In continue, the catalytic activity of Cu(II)-MP-bis(AMP)@boehmite has been used as a much efficient, reusable and hybrid of organic-inorganic nanocatalyst in the synthesis of ether derivatives through C-O coupling reaction under palladium-free and phosphine-free conditions. Cu(II)-MP-bis(AMP)@boehmite catalyst has been recovered and reused again for several times in the synthesis of ether derivatives.

Synthesis of (E)-2-(1H-tetrazole-5-yl)-3-phenylacrylenenitrile derivatives catalyzed by new ZnO nanoparticles embedded in a thermally stable magnetic periodic mesoporous organosilica under green conditions

ZnO nanoparticles embedded in a magnetic isocyanurate-based periodic mesoporous organosilica (Fe₃O₄@PMO–ICS–ZnO) were prepared through a modified environmentally-benign procedure for the first time and properly characterized by appropriate spectroscopic and analytical methods or techniques used for mesoporous materials. The new thermally stable Fe₃O₄@PMO–ICS–ZnO nanomaterial with proper active sites and surface area as well as uniform particle size was investigated for the synthesis of medicinally important tetrazole derivatives through cascade condensation and concerted 1,3-cycloaddition reactions as a representative of the Click Chemistry concept. The desired 5-substituted-1H-tetrazole derivatives were smoothly prepared in high to quantitative yields and good purity in EtOH under reflux conditions. Low catalyst loading, short reaction time and the use of green solvents such as EtOH and water instead of carcinogenic DMF as well as easy separation and recyclability of the catalyst for at least five consecutive runs without significant loss of its activity are notable advantages of this new protocol compared to other recent introduced procedures.

Stabilization of ruthenium on biochar-nickel magnetic nanoparticles as a heterogeneous, practical, selective, and reusable nanocatalyst for the Suzuki C-C coupling reaction in water

Waste recycling and the use of recyclable and available catalysts are important principles in green chemistry in science and industrial research. Therefore in this study, biochar nanoparticles were prepared from biomass pyrolysis. Then, they were magnetized with nickel nanoparticles to improve their recycling. Further, the magnetic biochar nanoparticles (biochar-Ni MNPs) were modified by dithizone ligand and then applied for the fabrication of a ruthenium catalyst (Ru-dithizone@biochar-Ni MNPs). This nanocatalyst was characterized by high-resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), wavelength dispersive X-ray spectroscopy (WDX), N₂ adsorption–desorption isotherms, thermogravimetric analysis (TGA), X-ray diffraction (XRD), and vibrating sample magnetometry (VSM) techniques. The XRD studies of Ru in the nanocatalyst showed that the crystalline structure of ruthenium in the Ru-dithizone@biochar-Ni MNPs was hcp. Another principle of green chemistry is the use of safe and inexpensive solvents, the most suitable of which is water. Therefore, the catalytic activity of this catalyst was investigated as a practical, selective, and recyclable nanocatalyst in the Suzuki carbon–carbon coupling reaction in aqueous media. The VSM curve of this catalyst showed that it could be easily recovered using an external magnet, and recycled multiple times. Also, VSM analysis of the recovered catalyst indicated the good magnetic stability of this catalyst after repeated use.

Waste recycling and the use of recyclable and available catalysts are important principles in green chemistry in science and industrial research.

Investigation of Fe3O4@boehmite NPs as efficient and magnetically recoverable nanocatalyst in the homoselective synthesis of tetrazoles

Magnetic boehmite nanoparticles (Fe₃O₄@boehmite NPs) were synthesized from a hybrid of boehmite and Fe₃O₄ nanoparticles. At first, boehmite nanoparticles (aluminum oxide hydroxide) were prepared via a simple procedure in water using commercially available materials such as sodium hydroxide and aluminum nitrate. Then, these nanoparticles were magnetized using Fe₃O₄ NPs in a basic solution of FeCl₂·4H₂O and FeCl₃·6H₂O. Fe₃O₄@boehmite NPs have advantages of both boehmite nanoparticles and Fe₃O₄ magnetic materials. Magnetic boehmite nanoparticles have been characterized by various techniques such as TEM, SEM, EDS, WDX, ICP, FT-IR, Raman, XRD and VSM. SEM and TEM images confirmed that particles size are less than 50 nm in diameter with a cubic orthorhombic structure. Then, Fe₃O₄@boehmite NPs were applied as a homoselective, highly efficient, cheap, biocompatibility, heterogeneous and magnetically recoverable nanocatalyst in the synthesis of 5-substituted 1H-tetrazole derivatives. Fe₃O₄@boehmite NPs can be recycled for several runs in the synthesis of tetrazoles. Also, all tetrazoles were isolated in high yields, which reveals high activity of Fe₃O₄@boehmite NPs in the synthesis of tetrazole derivatives. Fe₃O₄@boehmite NPs shows a good homoselectivity in synthesis of 5-substituted 1H-tetrazole derivatives.

Magnetic boehmite nanoparticles were synthesized from a hybrid of boehmite and Fe₃O₄ nanoparticles. Then, it was applied as a homoselective, highly efficient, cheep, heterogeneous and recoverable nanocatalyst in the synthesis of tetrazole derivative.

Nanomaterial catalyzed green synthesis of tetrazoles and its derivatives: a review on recent advancements

Tetrazoles are indispensable nitrogen containing heterocyclic scaffolds that offer a broad spectrum of applications in various domains such as medicinal chemistry, high energy material science, biochemistry, pharmacology etc. Owing to their useful applications, a wide range of catalysts have been explored for green synthesis of tetrazole derivatives. In recent times, nanomaterials have been emerged as extremely efficient catalysts for different organic transformations because of their high surface area-to-volume ratio, easy surface modification, simple fabrications, easy recovery and reusability. In this article, we have presented an overview of utilization of various nano-catalysts, nanocomposites and other solid-supported nanomaterials as an efficient environmental benign catalytic system for green synthesis of tetrazoles and derivatives. This review will provide an exclusive emphasis on boehmite, magnetic, copper, carbon, MCM-41, and composite based nanomaterials that have been developed since the year 2010 for the synthesis of tetrazole derivatives. In addition, we have briefly discussed the fabrication, functionalization and characterization of some novel nanomaterials and their advantages in the synthesis of tetrazole and its derivatives along with the reaction mechanism that involves synthesis of tetrazole derivatives via nanomaterials catalysed reactions.

Copper/Nickel-Decorated Olive Pit Biochar: One Pot Solid State Synthesis for Environmental Remediation

Developing micro- and nanomaterials for environmental pollution remediation is currently a pertinent topic. Among the plethora of strategies, designing supported nanocatalysts for the degradation of pollutants has achieved prominence. In this context, we are addressing one of the UN Sustainable Development Goals by valorizing agrowaste as a source of biochar, which serves as a support for bimetallic nanocatalysts. Herein, olive pit powder particles were impregnated with copper and nickel nitrates and pyrolyzed at 400 °C. The resulting material consists of bimetallic CuNi-decorated biochar. CuNi nanocatalysts were found to be as small as 10 nm and very well dispersed over biochar with zero valent copper and nickel and the formation of copper–nickel solid solutions. The biochar@CuNi (B@CuNi) exhibited typical soft ferromagnet hysteresis loops with zero remanence and zero coercivity. The biochar@CuNi was found to be an efficient catalyst of the reduction in methyl orange (MO) dye, taken as a model pollutant. In sum, the one-pot method devised in this work provides unique CuNi-decorated biochar and broadens the horizons of the emerging topic of biochar-supported nanocatalysts.

Magnetization of graphene oxide nanosheets using nickel magnetic nanoparticles as a novel support for the fabrication of copper as a practical, selective, and reusable nanocatalyst in C-C and C-O coupling reactions

Catalyst species are an important class of materials in chemistry, industry, medicine, and biotechnology. Moreover, waste recycling is an important process in green chemistry and is economically efficient. Herein, magnetic graphene oxide was synthesized using nickel magnetic nanoparticles and further applied as a novel support for the fabrication of a copper catalyst. The catalytic activity of supported copper on magnetic graphene oxide (Cu–ninhydrin@GO–Ni MNPs) was investigated as a selective, practical, and reusable nanocatalyst in the synthesis of diaryl ethers and biphenyls. Some of the obtained products were identified by NMR spectroscopy. This nanocatalyst has been characterized by atomic absorption spectroscopy (AAS), scanning electron microscopy (SEM), wavelength dispersive X-ray spectroscopy (WDX), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FT-IR), and vibrating sample magnetometer (VSM) techniques. The results obtained from SEM shown that this catalyst has a nanosheet structure. Also, XRD and FT-IR analysis show that the structure of graphene oxide and nickel magnetic nanoparticles is stable during the modification of the nanoparticles and synthesis of the catalyst. The VSM curve of the catalyst shows that this catalyst can be recovered using an external magnet; therefore, it can be reused several times without a significant loss of its catalytic efficiency. The heterogeneity and stability of this nanocatalyst during organic reactions was confirmed by the hot filtration test and AAS technique.

Catalytic activity of supported copper on magnetic graphene oxide was investigated as a selective and reusable nanocatalyst in the synthesis of diaryl ethers and biphenyls.

Biochar as a Biocompatible Mild Anti-Inflammatory Supplement for Animal Feed and Agricultural Fields

Biochar is an organic material and high in carbon content, besides its use for energy purposes, it is also a material that serves the purpose of improving soil fertility, organic matter content of soils and removing heavy metals from water and soil. This study aims to investigate the antimicrobial effects of biochar whose beneficial effects on agricultural productivity has been proven by different studies. Scientific literature concerning the antibacterial, antifungal, and antiviral effects of the apricot seed and olive seed biochar is limited. Biochar applications may help to alter the microbial diversity by modifying biological environment either in agriculture or in animal husbandry. Moreover, biochar has been used in animal husbandry to improve animal health especially by regulating the intestinal flora and inflammation in the intestines. Hence, in our study, we investigated the effect of biochar on the growth of Aspergillus niger, Cryphonectria parasitica, Phytophthora cinnamomi, Plenodomus tracheiphilus, Enterococcus casseliflavus, Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli and two different bacteriophage strains. Biochar did not have any direct effect on the growth of either Gram-positive or Gram-negative bacteria, bacteriophages, and fungi. In order to test their direct effects on the immune cells, mammalian macrophages were used and biochar directly reduced the inflammatory cytokine levels produced by the in vitro activated macrophages.

Algal magnetic nickel oxide nanocatalyst in accelerated synthesis of pyridopyrimidine derivatives

This research presents a novel biological route for the biosynthesis of nickel oxide nanoparticles (NiO NPs) using marine macroalgae extract as a reducing and coating agent under optimized synthesis conditions. XRD and TEM analyses revealed that phytosynthesized NiO NPs are crystalline in nature with a spherical shape having a mean particle size of 32.64 nm. TGA results indicated the presence of marine-derived organic constituents on the surface of NiO NPs. It is found that biogenic NiO NPs with BET surface area of 45.59 m²g^-1 is a highly efficient catalyst for benign one-pot preparation of pyridopyrimidine derivatives using aqueous reaction conditions. This environmentally friendly procedure takes considerable advantages of shorter reaction times, excellent product yields (up to 96%), magnetically viable nanocatalyst (7 runs), low catalyst loadings, and free toxic chemical reagents.

Magnetization of biochar nanoparticles as a novel support for fabrication of organo nickel as a selective, reusable and magnetic nanocatalyst in organic reactions

Waste recycling is important process in green chemistry and economic efficiency. Herein, magnetized biochar nanoparticles were modified under green and environmentally friendly method and further were applied as reusable catalyst in organic reactions.

Two Schiff-base Complexes of Copper and Zirconium Oxide Fabricated on Magnetic Nanoparticles as Practical and Recyclable Catalysts in C-C Coupling Reaction

:

Fe3O4 magnetic nanoparticles (MNPs) were prepared via a chemical co-precipitation method. Then, the surface of Fe3O4 MNPs was modified by (3-Chloropropyl)trimethoxysilane and then two Schiff-base complexes of zirconium oxide and copper were stabilized on modified Fe3O4 MNPs. These catalysts were characterized using SEM, EDS, WDX, FTIR, XRD, TGA, VSM and AAS techniques. The catalytic activity of these catalysts was described in the carbon-carbon coupling reaction. VSM analysis of these catalysts indicate the high magnetic performance, therefor these catalysts can be recovered by an external magnet and reused for several times without missing in the amount of catalysts. Reusability, excellent yields and high TON values indicate the high efficiency of these catalysts. Leaching of these catalysts was studied by AAS which leaching of copper or zirconium was not observed. Also, the stability of these catalysts was confirmed by characterization of recovered catalysts and comparing with fresh catalysts.