Heat-stimuli controllability of shape memory thermoplastic epoxy filaments by adding polyethylene glycol

Emerging Functional Polymer Composites for Tactile Sensing

In recent years, extensive research has been conducted on the development of high-performance flexible tactile sensors, pursuing the next generation of highly intelligent electronics with diverse potential applications in self-powered wearable sensors, human-machine interactions, electronic skin, and soft robotics. Among the most promising materials that have emerged in this context are functional polymer composites (FPCs), which exhibit exceptional mechanical and electrical properties, enabling them to be excellent candidates for tactile sensors. Herein, this review provides a comprehensive overview of recent advances in FPCs-based tactile sensors, including the fundamental principle, the necessary property parameter, the unique device structure, and the fabrication process of different types of tactile sensors. Examples of FPCs are elaborated with a focus on miniaturization, self-healing, self-cleaning, integration, biodegradation, and neural control. Furthermore, the applications of FPC-based tactile sensors in tactile perception, human-machine interaction, and healthcare are further described. Finally, the existing limitations and technical challenges for FPCs-based tactile sensors are briefly discussed, offering potential avenues for the development of electronic products.

Bulk Polymerization of Thermoplastic Shape Memory Epoxy Polymer for Recycling Applications

Conventional epoxy polymers are thermo-set and difficult to recycle and reuse. In this study, a series of linear thermoplastic epoxy polymers (EPx) with shape memory properties were prepared by using a bifunctional monoamine diglycolamine (DGA) as a curing agent and an equivalent amount of bifunctional rigid epoxy resin (E-51) and bifunctional flexible epoxy resin (polypropylenglycol diglycidyl ether, PPGDGE) in a bulk polymerization reaction. The results showed that these samples can fully react under the curing process of, 60 °C/2 h, followed by 80 °C/2 h, followed by 120 °C/2 h. The introduction of different contents of PPGDGE can adjust the T_g of the material to adapt to different environmental requirements, and can significantly increase the fracture strain of the material and improve its micro-phase separation structure. Thus, R_f of the material is close to 100%, and R_r is increased from 87.98% to 97.76%. Importantly, this linear chain structure allows the material to be easily recycled and reprocessed by dissolving or melting, and also means the material shows potential for 3D printing or other thermoplastic remolding.

Synthesis of Biodegradable Polyester-Polyether with Enhanced Hydrophilicity, Thermal Stability, Toughness, and Degradation Rate

Novel poly(butylene succinate-butylene furandicarboxylate/polyethylene glycol succinate) (PBSF-PEG) was synthesized using two-step transesterification and polycondensation in the melt. There are characterized by intrinsic viscosity, GPC, ¹H NMR, DSC, TGA, tensile, water absorption tests, and water degradation at different pH. GPC analysis showed that PBSF-PEG had high molecular weight with average molecular weight (M_w) up to 13.68 × 10⁴ g/mol. Tensile tests showed that these polymers possessed good mechanical properties with a tensile strength as high as 30 MPa and elongation at break reaching 1500%. It should be noted that the increase of PEG units improved the toughness of the polyester material. In addition, the introduction of PEG promoted the water degradation properties of PBSF, and the copolymer showed a significantly faster water degradation rate when the PEG unit content was 20%. This suggests that the amount of PEG introduced could be applied to regulate the water degradation rate of the copolymers. Hence, these new polymers have great potential for application as environmentally friendly and sustainable plastic packaging materials.

Heat-Stimuli Shape Memory Effect of Poly (ε-Caprolactone)-Cellulose Acetate Composite Tubular Scaffolds

Small-diameter artery disease is the most common clinical occurrence, necessitating the development of small-diameter artificial blood vessels. In this study, seven types of poly(-caprolactone)-cellulose acetate (PCL-CA) composite nanofiber membranes were prepared with different proportions of PCL and CA. The adhesion and growth of Mc3t3-e1 cells were considered to confirm the in vitro cytocompatibility of PCL-CA membranes. A smooth stainless-steel mandrel with a diameter of 4 mm was used to roll up the prepared nanofiber membranes to produce the tubular scaffold with 50 °C hot water. The tubular scaffolds were subjected to axial and circumferential tensile tests. The mechanical performance of the PCL-CA tubular scaffold could be improved by increasing the layers. In addition, the burst pressure (BP) of the tubular scaffolds was increased with the layers, and the BPs of six-layer (2380 ± 36.8 mmHg) and eight-layer (3720 ± 80.5 mmHg) tubular scaffolds were much higher than that of the human saphenous vein (2000 mmHg). The compression shape memory performances of the PCL-CA tubular scaffold with different layers were also investigated to simulate and analyze the contraction and expansion of tubular scaffolds. The experimental results showed that the compression strain of the tubular scaffold in the diameter direction reached 35%, and the ultimate shape recovery rate reached 87%. However, the shape fixity rate and shape recovery rate increased, demonstrating that the optimum number of layers can improve the compression shape memory performance of the tubular scaffold. The results of this study, including comprehensive morphological and mechanical properties and cytocompatibility, indicated the potential applicability of PCL-CA tubular scaffolds as tissue engineering grafts.