Insights into the effect of compaction pressure and material properties on interfacial bonding strength of bilayer tablets

The Effect of Compression Pressure on the First Layer Surface Roughness and Delamination of Metformin and Evogliptin Bilayer and Trilayer Tablets

The objectives of this study were to evaluate the delamination of convex-shaped metformin HCl (MF) and evogliptin tartrate (EG) multi-layer tablets depending on the pre-compression and main compression pressures and simultaneously correlate these results with those of a surface roughness analysis. Free-flowing MF and EG (median diameters of 38.3 and 44.7 μm, respectively) granules prepared using the wet granulation method were pre-compressed and subsequently compressed into bilayer and trilayer tablets using a universal testing machine. The compaction force required to break the tablets increased linearly as the main compression pressure increased (30-150 MPa). Conversely, the interfacial strength and compaction breaking force decreased as the pre-compression pressure increased (10-110 MPa). A surface roughness analysis employing a profilometer revealed that the first layer (MF) roughness drastically decreased from 5.89 to 0.51 μm (Ra, arithmetic average of profile height deviations from the mean line) as the pre-compression pressure increased from 10 to 150 MPa in the bilayer tablet. Accordingly, the decrease in the roughness of the first layer reduced the inter-penetration at the interface, as observed via energy dispersive spectrometer (EDS)-equipped scanning electron microscopy, decreasing the interfacial bonding strength and causing delamination of the MF/EG multi-layer tablets. These findings indicate the significance of roughness control in the actual preparation of multi-layer tablets and the usefulness of profilometer- and EDS-based surface analyses for interpreting the delamination of multi-layer tablets.

Reviewing the Impact of Powder Cohesion on Continuous Direct Compression (CDC) Performance

The pharmaceutical industry is undergoing a paradigm shift towards continuous processing from batch, where continuous direct compression (CDC) is considered to offer the most straightforward implementation amongst powder processes due to the relatively low number of unit operations or handling steps. Due to the nature of continuous processing, the bulk properties of the formulation will require sufficient flowability and tabletability in order to be processed and transported effectively to and from each unit operation. Powder cohesion presents one of the greatest obstacles to the CDC process as it inhibits powder flow. As a result, there have been many studies investigating potential manners in which to overcome the effects of cohesion with, to date, little consideration of how these controls may affect downstream unit operations. The aim of this literature review is to explore and consolidate this literature, considering the impact of powder cohesion and cohesion control measures on the three-unit operations of the CDC process (feeding, mixing, and tabletting). This review will also cover the consequences of implementing such control measures whilst highlighting subject matter which could be of value for future research to better understand how to manage cohesive powders for CDC manufacture.

Implementation of Quality by Design (QbD) for development of bilayer tablets

Bilayer tablets offer various drug release profiles for individual drugs incorporated in each layer of a bilayer tablet, which is rarely achievable by conventional tablets. These tablets also help avoid physicochemical incompatibilities between drugs and excipients. Successful manufacturing of such more complex dosage forms depends upon screening of material attributes of API and excipients as well as optimization of processing parameters of individual unit operations of the manufacturing process that must be strictly monitored and controlled to obtain an acceptable drug product quality and performance in order to achieve safety and efficacy per regulatory requirements. Optimizing formulation attributes and manufacturing processes during critical stages, such as blending, granulation, pre-compression, and main compression, can help avoid problems such as weight variation, segregation, and delamination of individual layers, which are frequently faced during the production of bilayer tablets. The main objective of this review is to establish the basis for the implementation of Quality by Design (QbD) system principles for the design and development of bilayer tablets, encompassing the preliminary and systematic risk assessment of critical material attributes (CMAs) and critical process parameters (CPPs) with respect to in-process and finished product critical quality attributes (CQAs). Moreover, the applicability of the QbD methodology based on its purpose is discussed and complemented with examples of bilayer tablet technology.

The effect of granules characters on mechanical properties of press-coated tablets: A comparative study

The aim of this study was to investigate the correlation between critical granules characters (including particle size, surface roughness, and apparent porosity) and mechanical properties of press-coated tablets. Granules of a model formulation were prepared through Roll Compaction Granulation (RCG), High Shear Granulation (HSG), and Fluidized Bed Granulation (FBG) to prepare granules with different surface roughness and apparent porosity. The surface roughness and porosity of granules had a significantly greater effect on mechanical properties than the particle size of granules. Whether for brittle or plastic materials, FBG granules with the roughest surface and the greatest apparent porosity exhibited the best compression properties. The elastic recovery test, the interlayer adhesion forces study, the break pattern test, and the X-ray microcomputed tomography investigation suggested that granules with great apparent porosity and rough surfaces could contribute to the production of stable press-coated structures. Moreover, for press-coated tablets prepared using granules, the proper granules in the coat layer could eliminate the side effect of the rigid core on the mechanical strength. The above understandings will be conducive to the selection of compatible and appropriate granules characters, which can enhance mechanical properties and extend the application of press-coated tablets.

Fabrication of bilayer tablets using hot melt extrusion-based dual-nozzle fused deposition modeling 3D printing

The objective of this study was to fabricate bilayer tablets using hot-melt extrusion (HME)-based dual-nozzle fused deposition modeling (FDM) three-dimensional (3D) printing techniques. Acetaminophen (APAP) and caffeine citrate (CC) were used as the model drugs. Five bilayer tablets with different formulations were developed and two different structures were printed for each formulation. Three-point bending, Hooke's law, and resistance and stiffness tests were conducted to determine the mechanical properties of the filaments. A novel method, 3D printed tablet retention rate, was developed and used for the first time to compare the printing quality of different filaments. The 3D printed tablets were evaluated to derive the drug release rates using a USP-II dissolution apparatus. HPMC HME 15LV and HPMCAS-LG were identified as good printing materials; however, HPMC HME 100LV was not suitable for printing under frequent nozzle switching conditions. Although mechanical characterization tests can be used to determine whether filaments can be printed, they cannot specifically distinguish the quality of printing between the filaments. Overall, this study revealed the successful fabrication of bilayer tablets via HME paired with dual-nozzle FDM 3D printing.

Emerging Multi-Drug Eutectics: Opportunities and Challenges

Complexity and heterogeneous nature of most diseases have posed greater challenges in the modern healthcare system. Fixed-dose combination can offer an ideal way to improve patient compliance and higher therapeutic efficacy. However, biopharmaceutical issues associated with the drug combinations remain unaddressed. Multidrug eutectics (MDE) have demonstrated significant promise in improving the biopharmaceutical attributes with synergistic therapeutic action. Eutectic mixtures are the multicomponent solid forms that possess lesser melting point than the individual components at a fixed composition. Non-covalent linking of drug combinations as MDE is an innovative strategy with enhanced solubility, dissolution, and mechanical and potential therapeutic efficacy. This review provides a comprehensive overview of the design of MDE, rational selection of drugs, characterization tools, and their therapeutic potential. Besides, the futuristic perspective where MDE could make a significant impact on combination therapy is briefly outlined. Graphical Abstract.

Interfacial bonding in formulated bilayer tablets

To take full advantage of the drug delivery benefits offered by bilayer tablets, the common issue of weak interfacial bonding strength (IBS) with manufacturing must be overcome. This work seeks to characterize the effects of composition in individual layers and compaction pressure on the IBS. Mixtures of MCC and lactose in different ratios with and without HPMC were used where the first layer was compacted with two different pressures (20 and 100 MPa) followed by a second layer compaction pressure of 200 MPa. After identifying the failure mode as either at the interface or within a layer, the complex trends of bilayer tablet IBS as a function of MCC content were explained by considering the interplay between particle bonding strength and bonding area at the interface.