Catalytic total oxidation of toluene over carbon-supported Cu Co oxide catalysts derived from Cu-based metal organic framework

Extraordinary synergy on 3D hierarchical porous Co-Cu nanocomposite for catalytic elimination of VOCs at low temperature and high space velocity

It is still a challenge to develop hierarchically nanostructured catalysts with simple approaches to enhance the low-temperature catalytic activity. Herein, a set of mesoporous Co-Cu binary metal oxides with different morphologies were successfully prepared via a facile ammonium bicarbonate precipitation method without any templates or surfactants, which were further applied for catalytic removal of carcinogenic toluene. Among the catalysts with different ratios, the CoCu0.2 composite oxide presented the best performance, where the temperature required for 90% conversion of toluene was only 237°C at the high weight hour space velocity (WHSV) of 240,000 mL/(gcat·hr). Meanwhile, compared to the related Co-Cu composite oxides prepared by using different precipitants (NaOH and H2C2O4), the NH4HCO3-derived CoCu0.2 sample exhibited better catalytic efficiency in toluene oxidation, while the T90 were 22 and 28°C lower than those samples prepared by NaOH and H2C2O4 routes, respectively. Based on various characterizations, it could be deduced that the excellent performance was related to the small crystal size (6.7 nm), large specific surface area (77.0 m2/g), hollow hierarchical nanostructure with abundant high valence Co ions and adsorbed oxygen species. In situ DRIFTS further revealed that the possible reaction pathway for the toluene oxidation over CoCu0.2 catalyst followed the route of absorbed toluene → benzyl alcohol → benzaldehyde → benzoic acid → carbonate → CO2 and H2O. In addition, CoCu0.2 sample could keep stable with long-time operation and occur little inactivation under humid condition (5 vol.% water), which revealed that the NH4HCO3-derived CoCu0.2 nanocatalyst possessed great potential in industrial applications for VOCs abatement.

An exploratory study of volatile and semi-volatile organic compounds in PM2.5 atmospheric particles from an outdoor environment in Brazil

The development of methods for determining volatile and semi-volatile organic compounds in public spaces has become necessary to identify potential health and environmental risks. This study presents a practical methodology for sampling, extracting, detecting, and identifying these compounds in a vehicular traffic region in Belo Horizonte, Brazil. The methodology uses direct-immersion solid phase microextraction (DI-SPME) and static headspace (SHS) to extract SVOCs/VOCs. Comprehensive time-of-flight gas chromatography mass spectrometry (GC×GC/Q-TOFMS) and gas chromatography coupled to mass spectrometry (GC/MS) were used to detect and identify compounds. The analysed samples, collected with a high-volume sampler (Hi-Vol) with quartz filters and in which particulate matter (PM2.5) was retained, showed the presence of more than 200 compounds, both biogenic (natural origin) and anthropogenic (human origin). Regarding the distribution of chemical classes, aromatic compounds were predominantly found at 29.2%, followed by esters at 20.8%, non-aromatic hydrocarbons at 5.6%, and carboxylic acids at 9.4%. Static headspace gas chromatography (HS-GC) enabled the identification and quantification of 21 volatile compounds, including BETX, dichloromethane, chloroform, and naphthalene, which are currently regulated by the US Environmental Protection Agency (EPA).

Hybrid Metal-Organic Frameworks (MOFs) for Various Catalysis Applications

Porous materials have been gaining popularity in catalysis applications, solving the current ecological challenges. Metal-organic frameworks (MOFs) are especially noteworthy for their high surface areas and customizable chemistry, giving them a wide range of potential applications in catalysis remediation. The review study delves into the various applications of MOFs in catalysis and provides a comprehensive summary. This review thoroughly explores MOF materials, specifically focusing on their diverse catalytic applications, including Lewis catalysis, oxidation, reduction, photocatalysis, and electrocatalysis. Also, this study emphasizes the significance of high-performance MOF materials, which possess adjustable properties and exceptional features, as a novel approach to tackling technological challenges across multiple sectors. MOFs make it an ideal candidate for catalytic reactions, as it enables efficient conversion rates and selectivity. Furthermore, the tunable properties of MOF make it possible to tailor its structure to suit specific catalytic requirements. This feature improves performance and reduces costs associated with traditional catalysts. In conclusion, MOF materials have revolutionized the field of catalysis and offer immense potential in solving various technological challenges across different industries.

Performance and Mechanism of Co and Mn Loaded on Fe-Metal-Organic Framework Catalysts with Different Morphologies for Simultaneous Degradation of Acetone and NO by Photothermal Coupling

VOCs can be used instead of ammonia as a reducing agent to remove NO, achieving the effect of removing VOCs and NO simultaneously. Due to the high energy consumption and low photocatalytic efficiency required for conventional thermocatalytic purification, photothermal coupled catalytic purification can integrate the advantages of photocatalysis and thermocatalysis in order to achieve the effect of pollutants being treated efficiently with a low energy consumption. In this study, samples loaded with Co and Mn catalysts were prepared using the hydrothermal method on Fe-MOF with various morphologies. The catalytic performance of each catalyst was analyzed by studying the effects of their physicochemical properties through various characterizations, including XRD, SEM, BET, XPS, H2-TPR, TEM and O2-TPD. The characterization results demonstrated that the specific surface area, pore volume, high valence Co and Mn atoms, surface adsorbed oxygen and the abundance of oxygen lattice defects in the catalysts were the most critical factors affecting the performance of the catalysts. Based on the results of the performance tests, the catalysts prepared with an octahedral-shaped Fe-MOF loaded with Co and Mn showed a better performance than those loaded with Co and Mn on a rod-shaped Fe-MOF. The conversions of acetone and NO reached 50% and 64%, respectively, at 240 °C. The results showed that the catalysts were capable of removing acetone and NO at the same time. Compared with the pure Fe-MOF without Co and Mn, the loaded catalysts showed a significantly higher ability to remove acetone and NO simultaneously under the combination of various factors. The key reaction steps for the catalytic conversion of acetone and NO on the catalyst surface were investigated according to the Mars-van Krevelen (MvK) mechanism, and a possible mechanism was proposed. This study presents a new idea for the simultaneous removal of acetone and NOx by photothermal coupling.

Benzene Oxidation in Air by an Amine-Functionalized Metal-Organic Framework-Derived Carbon- and Nitrogen-Loaded Zirconium Dioxide-Supported Platinum Catalyst

To learn more about the behavior of amine (NH2)-functionalized metal-organic framework (MOF)-derived noble metal catalysts in the removal of aromatic volatile organic compounds in air, benzene oxidation at low temperatures has been investigated using 0.2-, 0.8-, and 1.5%-platinum (Pt)/Universitetet i Oslo (UiO)-66-NH2. The benzene conversion (XB) of x%-Pt/UiO-66-NH2-R under dry conditions (175 °C) was 23% (x = 0.2%) < 52% (x = 0.8%) < 100% (x = 1.5%): 'R' suffix denotes reduction pretreatment using a hydrogen (10 vol %) and nitrogen mixture at 300 °C for the generation of metallic Pt (Pt0) sites and simultaneous partial MOF decomposition into carbon- and nitrogen-loaded zirconium dioxide. The prominent role of reduction pretreatment was apparent in benzene oxidation as 1.5%-Pt/UiO-66-NH2 did not exhibit catalytic activity below 175 °C (dry condition). The promotional role of moisture in benzene oxidation by 1.5%-Pt/UiO-66-NH2-R was evident with a rise in the steady-state reaction rate (r) at 110 °C (21 kPa molecular oxygen (O2)) from 1.3 × 10-3 to 5.0 × 10-3 μmol g-1 s-1 as the water (H2O) partial pressure increased from 0 to 1.88 kPa. In contrast, the activity was lowered with increasing RH due to catalyst poisoning by excess moisture (r (110 °C) of 6.6 × 10-04 μmol g-1 s-1 at 2.83 kPa H2O (21 kPa O2)). Kinetic modeling suggests that XB proceeds through the Langmuir-Hinshelwood mechanism on the Pt/UiO-66-NH2-R surface (dissociative O2 chemisorption and the involvement of two oxygen species in benzene oxidation). According to the density functional theory simulation, the carbon and nitrogen impurities are to make the first XB step (i.e., hydrogen migration from the benzene molecule to the substrate) energetically favorable. The second hydrogen atom from the benzene molecule is also extracted effectively, while the oxygen derived from O2 facilitates further XB. The Pt0 sites dissociate the O2 and H2O molecules, while the product of the latter, i.e., free hydrogen and hydroxyl, makes the subsequent XB steps energetically favorable.

Investigation of the physico-chemical properties of Ni-Mg-Al-La catalysts from ultrasound-assisted synthesis

This work reports on the ultrasonic synthesis of layered double hydroxides (LDH), also known as hydrotalcite-type materials. We have studied the influence of ultrasonic irradiation parameters (power, time, temperature) on the physicochemical properties of Ni2Mg4Al1.8La0.2 hydrotalcite-type precursors and related mixed oxides (MO). The low-frequency acoustic cavitation (22 kHz) was applied during the precipitation and aging steps of co-precipitation synthesis and the results were compared to the classical preparation route. The materials were characterized by ATR-FTIR, XRD, N2 adsorption-desorption, SEM-EDX, S/TEM-HAADF, and XPS. Using the combination of acoustic cavitation-assisted precipitation and aging steps, XRD experiments show a higher purity hydrotalcite phase and a better incorporation of lanthanum ions into the LDH structure. As expected, morphological characterization shows a reduction in average crystallite size and an increase in surface area and pore volume, combined with a drastic reduction in synthesis time (45 min at room temperature versus 19 h at 60 °C in conventional synthesis). The insertion of a larger quantity of La is observed by S/TEM-EDSX mapping which also shows a better distribution of lanthanum atoms within the LDH and mixed oxide structures.

Effective construction of a CuCo MOF@graphene functional electrocatalyst for hydrogen evolution reaction

Electrochemical water splitting is considered a green and sustainable method of producing hydrogen energy. Herein, to pursue a highly efficient hydrogen evolution reaction, we fabricated high-performance electrocatalysts, by utilizing a bimetallic (Cu and Co) metal-organic framework to modify rGO through a one-step in situ approach. The synthesized CuCoOC@rGO presents a highly ordered structure with a defect-rich porous surface for the hydrogen evolution reaction (HER). Specifically, the appropriate adjustment of metal (Cu and Co), 1,3,5-benzenetricarboxylic acid (H3BTC), and rGO ratios leads to a well-defined morphology, which creates a defect-rich porous surface. Characterized by XRD, SEM, EDS, FT-IR spectroscopy, Raman spectroscopy, XPS, and BET, the morphology exposes more active sites, strong evidence for the promotion of electrocatalytic efficiency. Upon the analysis of the experimental data, the obtained CuCoOC@rGO catalyst exhibits excellent activity in alkaline media with a low overpotential of 120 mV at a current density of 10 mA cm-2, and a Tafel slope of 124 mV dec-1 for the hydrogen evolution reaction (HER). Guided by the structure-activity relationship, the superior HER activity of CuCoOC@rGO in alkaline electrolyte could originate from many sources, including: (1) as a self-supported substrate, CuCoOC@rGO not only leads to profitable electrical contact and mechanical stability but also firmly roots into the rGO without extra binders. (2) The highly ordered structure provides smooth ion and electron transport channels, which are conducive to electrolyte infiltration and gas release. (3) The abundance of defective pores on the surface of the nanoarrays, which offers more active sites for the catalytic process. This study provides new prospects for the rational design and fabrication of advanced hierarchical functional electrocatalysts for application in electrochemical energy devices.

Core-shell CoCuOx@MOx (MNb, Ti and Ce) catalysts with outstanding durability and resistance to H2O for the catalytic combustion of o-dichlorobenzene

Configuring Co-based catalysts with excellent activity, durability, anti-H₂O capability and superior chlorine resistance is an effective strategy for catalytic combustion of CVOCs. In this work, we elaborated a CoCuO_x catalysts with the same core but different shell. The CoCuO_x dodecahedron surface was successfully coated with shells of Nb₂O₅, TiO₂, and CeO₂ using a range of conventional synthesis methods. The prepared core-shell catalysts (CoCuO_x@TiO₂ and CoCuO_x@Nb₂O₅) were found to generate plentiful acid sites and abundant lattice oxygen species, indicating a strong interaction between the core and shell layers that resulted in a significant enhancement of catalytic activity. Additionally, by-products generation was successfully controlled by acid sites and lattice oxygen species. More importantly, the core-shell structure design significantly improved the thermal stability and anti-H₂O capability of the catalysts. Furthermore, the possible formation pathways and reaction mechanisms were proposed based on in-situ FTIR and selectivity analysis.

Research Progress of a Composite Metal Oxide Catalyst for VOC Degradation

Volatile organic compounds (VOCs) are atmospheric pollutants that have been of concern for researchers in recent years because they are toxic, difficult to remove, and widely sourced and easily cause damage to the environment and human body. Most scholars use low-temperature plasma biological treatment, catalytic oxidation, adsorption, condensation, and recovery techniques to treat then effectively. Among them, catalytic oxidation technology has the advantages of a high catalytic efficiency, low energy consumption, high safety factor, high treatment efficiency, and less secondary pollution; it is currently widely used for VOC degradation technology. In this paper, the catalytic oxidation technology for the degradation of multiple types of VOCs as well as the development of a single metal oxide catalyst have been briefly introduced. We also focus on the research progress of composite metal oxide catalysts for the removal of VOCs by comparing and analyzing the metal component ratio, preparation method, and types of precursors and the catalysts' influence on the catalytic performance. In addition, the reason for catalyst deactivation and a correlation between the chemical state of the catalyst and the electron distribution are discussed. Development of a composite metal oxide catalyst for the catalytic oxidation of VOCs has been proposed.

Interface-Enhanced Oxygen Vacancies of CoCuOx Catalysts In Situ Grown on Monolithic Cu Foam for VOC Catalytic Oxidation

The development of highly efficient and stable monolithic catalysts is essential for the removal of volatile organic compounds (VOCs). Copper foam (CF) is a potential ideal carrier for monolithic catalysts, but its low surface area is not conducive to dispersion of active species, thus reducing the interface interaction with active species. Herein, a vertically oriented Cu(OH)₂ nanorod was in situ grown on the CF, which acted as the template and precursor to synthesize CoCu-MOF. The optimized catalyst (12CoCu-R) delivers excellent performance for acetone oxidation with a T₉₀ of 195 °C. Impressively, the catalyst demonstrated satisfactory stability in long-term, cycle, water resistance, and high airspeed tests. Therefore, the present study provides a novel strategy for rationally designing efficient monolithic catalysts for VOC oxidation and other environmental applications.

Synthesis of novel highly-dispersed manganese oxide on porous calcium silicate for the catalytic oxidation of toluene

Highly-dispersed MnOx with abundant oxygen vacancy on porous calcium silicate for the catalytic oxidation of toluene.

Efficient catalytic degradation of toluene at a readily prepared Mn-Cu catalyst: Catalytic performance and reaction pathway

Fabricating of economical transitional metal oxide-based materials with satisfied low-temperature catalytic performance and application perspective is still a challenge in deep degradation of VOCs. Here, Mn-Cu bimetallic oxides were facilely prepared by one-step hydrothermal-redox method, which displayed much higher catalytic activity in toluene oxidation than those synthesized by hydrolysis-driven redox-precipitation or co-precipitation approach. It is shown that the lattice defect and oxygen vacancy concentration over prepared materials can be tuned by controlling Cu/Mn molar ratio. Amongst, spinel structured MnCu_0.5 exhibited the highest catalytic activity, superior durability and water resistance in toluene total oxidation owing to abundant surface adsorbed oxygen species, excellent low-temperature reducibility, and high amounts of Cu⁺ and Mn³⁺. In detail, the reaction rate of MnCu_0.5 was over 9.0 times higher than that of MnCu_0.75, MnCu_0.75-P and MnCu_0.75-H₂O₂ at relative low temperature of 210 °C. The cyclic redox process with easier oxygen species mobility played a key role in the catalytic oxidation of toluene. Typical reaction intermediates as benzyl alcohol, benzaldehyde, benzene, phenol, and benzoquinone could be detected by PTR-MS, which further decomposed to acetone, ethanol, ketone, acetic acid, methanol, formaldehyde and acetaldehyde species by ring opening before total mineralization.