Stabilization of ficin extract by immobilization on glyoxyl agarose. Preliminary characterization of the biocatalyst performance in hydrolysis of proteins

Changes in ficin specificity by different substrate proteins promoted by enzyme immobilization

Ficin extract has been immobilized using different supports: glyoxyl and Aspartic/1,6 hexamethylenediamine (Asp/HA) agarose beads. The latter was later submitted to glutaraldehyde modification to get covalent immobilization. The activities of these 3 kinds of biocatalysts were compared utilizing 4 different substrates, casein, hemoglobin and bovine serum albumin and benzoyl-arginine-p-nitroanilide at pH 7 and 5. Using glyoxyl-agarose, the effect of enzyme-support reaction time on the activity versus the four substrates at both pH values was studied. Reaction time has been shown to distort the enzyme due to an increase in the number of covalent support-enzyme bonds. Surprisingly, for all the substrates and conditions the prolongation of the enzyme-support reaction did not imply a decrease in enzyme activity. Using the Asp/HA supports (with different amount of HA) differences in the effect on enzyme activity versus the different substrates are much more significant, while with some substrates the immobilization produced a decrease in enzyme activity, with in other cases the activity increased. These different effects are even increased after glutaraldehyde treatment. That way, the conformational changes induced by the biocatalyst immobilization or the chemical modification fully altered the enzyme protein specificity. This may also have some implications when following enzyme inactivation.

Designing tailor-made steric matters to improve the immobilized ficin specificity for small versus large proteins

The development of strategies that can permit to adjust the size specificity of immobilized proteases by the generation of steric hindrances may enlarge its applicability. Using as a model ficin immobilized on glyoxyl agarose, two strategies were assayed to generate tailor made steric hindrances. First, ficin has been coimmobilized on supports coated with large proteins (hemoglobin or bovine serum albumin (BSA)). While coimmobilization of ficin with BSA presented no effect on the activity versus any of the assayed substrates, coimmobilization with hemoglobin permitted to improve the immobilized ficin specificity for casein versus hemoglobin, but still significant activity versus hemoglobin remained. Second, aldehyde-dextran has been employed to modify the immobilized ficin, trying to generate steric hindrances to avoid the entry of large proteins (hemoglobin) while enabling the entry of small ones (casein). This also increased the size specificity of ficin, but still did not suppress the activity versus hemoglobin. The combination of both strategies and the use of 37ºC during the proteolysis enabled to almost fully nullify the hydrolytic activity versus hemoglobin while preserving a high percentage of the activity versus casein. The modifications improved enzyme stability and the biocatalyst could be reused for 5 cycles without alteration of its properties.

Tailoring the specificity of ficin versus large hemoglobin and small casein by co-immobilizing inert proteins on the immobilized enzyme layer and further modification with aldehyde dextran

Ficin has been immobilized at full loading on glyoxyl agarose beads. Then, ficin was blocked with 2,2'-dipyridyldisulfide. To be effective, the modification must be performed in the presence of 0.5 M urea, as the enzyme was not inhibited under standard conditions, very likely because the catalytic Cys was not fully exposed to the medium. Activity could be fully recovered by incubation with 1 M mercaptoethanol. This biocatalyst could hydrolyze hemoglobin and casein. The objective of this paper was to increase the enzyme specificity versus small proteins by generating steric hindrances to the access of large proteins. The step by step blocking via ionic exchange of the biocatalyst with aminated bovine serum albumin (BSA), aldehyde dextran and a second layer of aminated BSA produced a biocatalyst that maintained its activity versus small synthetic substrates, increased the biocatalyst stability, while reduced its activity to over 50 % versus casein. Interestingly, this treatment almost fully annulled the activity versus hemoglobin, more effectively at 37 °C than at 55 °C. The biocatalyst could be reused 5 times without changes in activity. The changes could be caused by steric hindrances, but it cannot be discarded some changes in enzyme sequence specificity caused by the modifications.

Support Enzyme Loading Influences the Effect of Aldehyde Dextran Modification on the Specificity of Immobilized Ficin for Large Proteins

It has been reported that the modification of immobilized glyoxyl-ficin with aldehyde dextran can promote steric hindrances that greatly reduce the activity of the immobilized protease against hemoglobin, while the protease still maintained a reasonable level of activity against casein. In this paper, we studied if this effect may be different depending on the amount of ficin loaded on the support. For this purpose, both the moderately loaded and the overloaded glyoxyl-ficin biocatalysts were prepared and modified with aldehyde dextran. While the moderately loaded biocatalyst had a significantly reduced activity, mainly against hemoglobin, the activity of the overloaded biocatalyst was almost maintained. This suggests that aldehyde dextran was able to modify areas of the moderately loaded enzyme that were not available when the enzyme was overloaded. This modification promoted a significant increase in biocatalyst stability for both biocatalysts, but the stability was higher for the overloaded biocatalyst (perhaps due to a combination of inter- and intramolecular crosslinking).

Proteases: Importance, Immobilization Protocols, Potential of Activated Carbon as Support, and the Importance of Modifying Supports for Immobilization

Although enzymes have been used for thousands of years, their application in industrial processes has gained importance since the 20th century due to technological and scientific advances in several areas, including biochemistry [...].

Progress of ligand-modified agarose microspheres for protein isolation and purification

Proteins are the material basis of life and the primary carriers of life activities, containing various impurities that must be removed before use. To keep pace with the increasing complexity of protein samples, it is essential to constantly work on developing new purification technologies for downstream processes. While traditional downstream purification methods rely heavily on protein A affinity chromatography, there is still a lot of interest in finding safer and more cost-effective alternatives to protein A. Many non-affinity ligands and technologies have also been developed in biological purification recently. Here, the current status of biotechnology and the progress of protein separation technology from 2018 to 2023 are reviewed from the aspects of new preparation methods and new composite materials of commonly used separation media. The research status of new ligands with different mechanisms of action was reviewed, including the expanded application of affinity ligands, the development prospect of biotechnology such as polymer grafting, continuous column technology, and its new applications.

Proteases immobilized on nanomaterials for biocatalytic, environmental and biomedical applications: Advantages and drawbacks

Proteases have gained significant scientific and industrial interest due to their unique biocatalytic characteristics and broad-spectrum applications in different industries. The development of robust nanobiocatalytic systems by attaching proteases onto various nanostructured materials as fascinating and novel nanocarriers has demonstrated exceptional biocatalytic performance, substantial stability, and ease of recyclability over multiple reaction cycles under different chemical and physical conditions. Proteases immobilized on nanocarriers may be much more resistant to denaturation caused by extreme temperatures or pH values, detergents, organic solvents, and other protein denaturants than free enzymes. Immobilized proteases may present a lower inhibition. The use of non-porous materials in the immobilization prevents diffusion and steric hindrances during the binding of the substrate to the active sites of enzymes compared to immobilization onto porous materials; when using very large or solid substrates, orientation of the enzyme must always be adequate. The advantages and problems of the immobilization of proteases on nanoparticles are discussed in this review. The continuous and batch reactor operations of nanocarrier-immobilized proteases have been successfully investigated for a variety of applications in the leather, detergent, biomedical, food, and pharmaceutical industries. Information about immobilized proteases on various nanocarriers and nanomaterials has been systematically compiled here. Furthermore, different industrial applications of immobilized proteases have also been highlighted in this review.

An Up-to-Date Review on the Remediation of Dyes and Phenolic Compounds from Wastewaters Using Enzymes Immobilized on Emerging and Nanostructured Materials: Promises and Challenges

Addressing the critical issue of water pollution, this review article emphasizes the need to remove hazardous dyes and phenolic compounds from wastewater. These pollutants pose severe risks due to their toxic, mutagenic, and carcinogenic properties. The study explores various techniques for the remediation of organic contaminants from wastewater, including an enzymatic approach. A significant challenge in enzymatic wastewater treatment is the loss of enzyme activity and difficulty in recovery post-treatment. To mitigate these issues, this review examines the strategy of immobilizing enzymes on newly developed nanostructured materials like graphene, carbon nanotubes (CNTs), and metal-organic frameworks (MOFs). These materials offer high surface areas, excellent porosity, and ample anchoring sites for effective enzyme immobilization. The review evaluates recent research on enzyme immobilization on these supports and their applications in biocatalytic nanoparticles. It also analyzes the impact of operational factors (e.g., time, pH, and temperature) on dye and phenolic compound removal from wastewater using these enzymes. Despite promising outcomes, this review acknowledges the challenges for large-scale implementation and offers recommendations for future research to tackle these obstacles. This review concludes by suggesting that enzyme immobilization on these emerging materials could present a sustainable, environmentally friendly solution to the escalating water pollution crisis.

One-pot encapsulation of lactate dehydrogenase and Fe3O4 nanoparticles into a metal-organic framework: A novel magnetic recyclable biocatalyst for the synthesis of D-phenyllactic acid

The main challenges in bio-catalysis of d-phenyllactic acid (D-PLA) are poor tolerance of lactate dehydrogenase (LDH) to harsh environmental conditions and inability to recycle the catalyst. A novel magnetic framework composite was prepared as solid support for the immobilization of enzymes via one-pot encapsulation in this study. LDH/MNPs@MAF-7 was synthesized by the one-pot encapsulation of both LDH and magnetic nanoparticles (MNPs) in MAF-7. The LDH/MNPs@MAF-7 showed stable biological activity for the efficient biosynthesis of D-PLA. The structure and morphology of LDH/MNPs@MAF-7 were systematically characterized by SEM, FT-IR, XRD, VSM, XPS, TGA and N₂ sorption. These indicated that LDH/MNPs@MAF-7 was successfully synthesized, exhibiting enhanced resistance to acid and alkali, temperature and organic solvents. Furthermore, the bio-catalyst could be separated easily using a magnet, and the reusability was once considerably expanded with 80% of enzyme activity last after eight rounds of recycling. Therefore, LDH/MNPs@MAF-7 could be used as a potential biocatalyst for the biosynthesis of D-PLA due to its good stability and recovery properties.

Switch off/switch on of a cysteinyl protease as a way to preserve the active catalytic group by modification with a reversible covalent thiol modifier: Immobilization of ficin on vinyl-sulfone activated supports

The immobilization of ficin (a cysteinyl proteases) on vinyl sulfone agarose produced its almost full inactivation. It was observed that the incubation of the free and immobilized enzyme in β-mercaptoethanol produced a 20 % of enzyme activity recovery, suggesting that the inactivation due to the immobilization could be a consequence of the modification of the catalytic Cys. To prevent the enzyme inactivation during the immobilization, switching off of ficin via Cys reaction with dipyridyl-disulfide was implemented, giving a reversible disulfide bond that produced a fully inactive enzyme. The switch on of ficin activity was implemented by incubation in 1 M β-mercaptoethanol. Using this strategy to immobilize the enzyme on vinyl sulfone agarose beads, the expressed activity of the immobilized ficin could be boosted up to 80 %. The immobilized enzyme presented a thermal stabilization similar to that obtained using ficin-glyoxyl-agarose beads. This procedure may be extended to many enzymes containing critical Cys, to permit their immobilization or chemical modification.

Lactate dehydrogenase encapsulated in a metal-organic framework: A novel stable and reusable biocatalyst for the synthesis of D-phenyllactic acid

In this study, we synthesized a novel biocatalyst by encapsulating lactate dehydrogenase (LDH) in the metal-organic framework ZIF-90 by one-pot embedding. It showed strong biological activity for efficient synthesis of D-phenyllactic acid (D-PLA). The morphology and structure of LDH@ZIF-90 was systematically characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) spectroscopy, confocal laser scanning microscopy (CLSM) and gas sorption. According to thermogravimetric analysis (TGA), the enzyme loading of the biocatalyst was 3 %. The Michaelis-Menten constant (K_m) and maximal reaction rate (V_max) of LDH@ZIF-90 were similar to those of free LDH, which proved that ZIF-90 had good biocompatibility to encapsulate LDH. At the same time, LDH@ZIF-90 exhibited enhanced tolerance to temperature, pH and organic solvents, and its reusability was greatly improved with 68 % of initial enzyme activity remaining after 7 rounds of recylcing. Overall, LDH encapsulated in ZIF-90 may be an economically competitive and environmentally friendly novel biocatalyst for the synthesis of D-PLA.

Is enzyme immobilization a mature discipline? Some critical considerations to capitalize on the benefits of immobilization

Enzyme immobilization has been developing since the 1960s and although many industrial biocatalytic processes use the technology to improve enzyme performance, still today we are far from full exploitation of the field. One clear reason is that many evaluate immobilization based on only a few experiments that are not always well-designed. In contrast to many other reviews on the subject, here we highlight the pitfalls of using incorrectly designed immobilization protocols and explain why in many cases sub-optimal results are obtained. We also describe solutions to overcome these challenges and come to the conclusion that recent developments in material science, bioprocess engineering and protein science continue to open new opportunities for the future. In this way, enzyme immobilization, far from being a mature discipline, remains as a subject of high interest and where intense research is still necessary to take full advantage of the possibilities.

A review on the immobilization of pepsin: A Lys-poor enzyme that is unstable at alkaline pH values

Pepsin is a protease used in many different applications, and in many instances, it is utilized in an immobilized form to prevent contamination of the reaction product. This enzyme has two peculiarities that make its immobilization complex. The first one is related to the poor presence of primary amino groups on its surface (just one Lys and the terminal amino group). The second one is its poor stability at alkaline pH values. Both features make the immobilization of this enzyme to be considered a complicated goal, as most of the immobilization protocols utilize primary amino groups for immobilization. This review presents some of the attempts to get immobilized pepsin biocatalyst and their applications. The high density of anionic groups (Asp and Glu) make the anion exchange of the enzyme simpler, but this makes many of the strategies utilized to immobilize the enzyme (e.g., amino-glutaraldehyde supports) more related to a mixed ion exchange/hydrophobic adsorption than to real covalent immobilization. Finally, we propose some possibilities that can permit not only the covalent immobilization of this enzyme, but also their stabilization via multipoint covalent attachment.

Production of Plant Proteases and New Biotechnological Applications: An Updated Review

An updated review of emerging plant proteases with potential biotechnological application is presented. Plant proteases show comparable or even greater performance than animal or microbial proteases for by-product valorization through hydrolysis for, for example, cheese whey, bird feathers, collagen, keratinous materials, gelatin, fish protein, and soy protein. Active biopeptides can be obtained as high added value products, which have shown numerous beneficial effects on human health. Plant proteases can also be used for wastewater treatment. The production of new plant proteases is encouraged for the following advantages: low cost of isolation using simple procedures, remarkable stability over a wide range of operating conditions (temperature, pH, salinity, and organic solvents), substantial affinity to a broad variety of substrates, and possibility of immobilization. Vegetable proteases have enormous application potential for the valorization of industrial waste and its conversion into products with high added value through low-cost processes.

Stabilization of enzymes via immobilization: Multipoint covalent attachment and other stabilization strategies

The use of enzymes in industrial processes requires the improvement of their features in many instances. Enzyme immobilization, a requirement to facilitate the recovery and reuse of these water-soluble catalysts, is one of the tools that researchers may utilize to improve many of their properties. This review is focused on how enzyme immobilization may improve enzyme stability. Starting from the stabilization effects that an enzyme may experience by the mere fact of being inside a solid particle, we detail other possibilities to stabilize enzymes: generation of favorable enzyme environments, prevention of enzyme subunit dissociation in multimeric enzymes, generation of more stable enzyme conformations, or enzyme rigidification via multipoint covalent attachment. In this last point, we will discuss the features of an "ideal" immobilization protocol to maximize the intensity of the enzyme-support interactions. The most interesting active groups in the support (glutaraldehyde, epoxide, glyoxyl and vinyl sulfone) will be also presented, discussing their main properties and uses. Some instances in which the number of enzyme-support bonds is not directly related to a higher stabilization will be also presented. Finally, the possibility of coupling site-directed mutagenesis or chemical modification to get a more intense multipoint covalent immobilization will be discussed.

Immobilization of papain: A review

Papain is a cysteine protease from papaya, with many applications due to its broad specificity. This paper reviews for first time the immobilization of papain on different supports (organic, inorganic or hybrid supports) presenting some of the features of the utilized immobilization strategies (e.g., epoxide, glutaraldehyde, genipin, glyoxyl for covalent immobilization). Special focus is placed on the preparation of magnetic biocatalysts, which will permit the simple recovery of the biocatalyst even if the medium is a suspension. Problems specific to the immobilization of proteases (e.g., steric problems when hydrolyzing large proteins) are also defined. The benefits of a proper immobilization (enzyme stabilization, widening of the operation window) are discussed, together with some artifacts that may suggest an enzyme stabilization that may be unrelated to enzyme rigidification.

Effect of Tris Buffer in the Intensity of the Multipoint Covalent Immobilization of Enzymes in Glyoxyl-Agarose Beads

Tris is an extensively used buffer that presents a primary amine group on its structure. In the present work trypsin, chymotrypsin and penicillin G acylase (PGA) were immobilized/stabilized on glyoxyl agarose in presence of different concentrations of Tris (from 0 to 20 mM). The effects of the presence of Tris during immobilization were studied analyzing the thermal stability of the obtained immobilized biocatalysts. The results indicate a reduction of the enzyme stability when immobilized in the presence of Tris. This effect can be observed in inactivations carried out at pH 5, 7, and 9 with all the enzymes assayed. The reduction of enzyme stability increased with the Tris concentration. Another interesting result is that the stability reduction was more noticeable for immobilized PGA than in the other immobilized enzymes, the biocatalysts prepared in presence of 20 mM Tris lost totally the activity at pH 7 just after 1 h of inactivation, while the reference at this time still kept around 61 % of the residual activity. These differences are most likely due to the homogeneous distribution of the Lys groups in PGA compared to trypsin and chymotrypsin (where almost 50% of Lys group are in a small percentage of the protein surface). The results suggest that Tris could be affecting the multipoint covalent immobilization in two different ways, on one hand, reducing the number of available glyoxyl groups of the support during immobilization, and on the other hand, generating some steric hindrances that difficult the formation of covalent bonds.

Chemical and physical Chitosan modification for designing enzymatic industrial biocatalysts: How to choose the best strategy?

Chitosan is one of the most abundant natural polymer worldwide, and due to its inherent characteristics, its use in industrial processes has been extensively explored. Because it is biodegradable, biocompatible, non-toxic, hydrophilic, cheap, and has good physical-chemical stability, it is seen as an excellent alternative for the replacement of synthetic materials in the search for more sustainable production methodologies. Thus being, a possible biotechnological application of Chitosan is as a direct support for enzyme immobilization. However, its applicability is quite specific, and to overcome this issue, alternative pretreatments are required, such as chemical and physical modifications to its structure, enabling its use in a wider array of applications. This review aims to present the topic in detail, by exploring and discussing methods of employment of Chitosan in enzymatic immobilization processes with various enzymes, presenting its advantages and disadvantages, as well as listing possible chemical modifications and combinations with other compounds for formulating an ideal support for this purpose. First, we will present Chitosan emphasizing its characteristics that allow its use as enzyme support. Furthermore, we will discuss possible physicochemical modifications that can be made to Chitosan, mentioning the improvements obtained in each process. These discussions will enable a comprehensive comparison between, and an informed choice of, the best technologies concerning enzyme immobilization and the application conditions of the biocatalyst.

Sugarcane Bagasse Saccharification by Enzymatic Hydrolysis Using Endocellulase and β-glucosidase Immobilized on Different Supports

The saccharification of sugarcane bagasse by enzymatic hydrolysis is one of the most promising processes for obtaining fermentable sugar to be used in the production of second-generation ethanol. The objective of this work was to study the immobilization and stabilization of two commercial enzymes: Endocellulase (E-CELBA) in dextran coated iron oxide magnetic nanoparticles activated with aldehyde groups (DIOMNP) and β-glucosidase (E-BGOSPC) in glyoxyl agarose (GLA) so that their immobilized derivatives could be applied in the saccharification of pretreated sugarcane bagasse. This was the first time that the pretreated sugarcane bagasse was saccharified by cascade reaction using a endocellulase immobilized on dextran coated Fe2O3 with aldehyde groups combined with a β-glucosidase immobilized on glyoxyl agarose. Both enzymes were successfully immobilized (more than 60% after reduction with sodium borohydride) and presented higher thermal stability than free enzymes at 60, 70, and 80 °C. The enzymatic hydrolysis of the sugarcane bagasse was carried out with 15 U of each enzyme per gram of bagasse in a solid-liquid ratio of 1:20 for 48 h at 50 °C. Under these conditions, 39.06 ± 1.18% of the cellulose present in the pretreated bagasse was hydrolyzed, producing 14.11 ± 0.47 g/L of reducing sugars (94.54% glucose). In addition, DIOMNP endo-cellulase derivative maintained 61.40 ± 1.17% of its enzymatic activity after seven reuse cycles, and GLA β-glucosidase derivative maintained up to 58.20 ± 1.55% of its enzymatic activity after nine reuse cycles.

Effect of amine length in the interference of the multipoint covalent immobilization of enzymes on glyoxyl agarose beads

Trypsin, chymotrypsin, penicillin G acylase and ficin extract have been stabilized by immobilization on glyoxyl agarose, adding different aliphatic compounds bearing a primary amine group during the immobilization: ethyl amine, butyl amine, hexyl amine (at concentrations ranging from 0 to 20 mM) and octyl amine (from 0 to 10 mM) to analyze their effects on the immobilized enzyme stability. As expected, the presence of amines reduced the intensity of the enzyme-support multipoint covalent attachment, and therefore the enzyme stability. However, it is clear that this effect is higher using octyl amine for all enzymes (in some cases the enzyme immobilized in the presence of 10 mM octyl amine was almost inactivated while the reference kept over 50 % of the initial activity). This way, it seems that the most important effect of the presence of aminated compounds came from the generation of steric hindrances to the enzyme/support multi-reaction promoted by the ammines that are interacting with the aldehyde groups. In some instances, just 1 mM of aminated compounds is enough to greatly decrease enzyme stability. The results suggested that, if the composition of the enzyme extract is unknown, to eliminate small aminated compounds may be necessary to maximize the enzyme-support reaction.

Effect of Concentrated Salts Solutions on the Stability of Immobilized Enzymes: Influence of Inactivation Conditions and Immobilization Protocol

This paper aims to investigate the effects of some salts (NaCl, (NH₄)₂SO₄ and Na₂SO₄) at pH 5.0, 7.0 and 9.0 on the stability of 13 different immobilized enzymes: five lipases, three proteases, two glycosidases, and one laccase, penicillin G acylase and catalase. The enzymes were immobilized to prevent their aggregation. Lipases were immobilized via interfacial activation on octyl agarose or on glutaraldehyde-amino agarose beads, proteases on glyoxyl agarose or glutaraldehyde-amino agarose beads. The use of high concentrations of salts usually has some effects on enzyme stability, but the intensity and nature of these effects depends on the inactivation pH, nature and concentration of the salt, enzyme and immobilization protocol. The same salt can be a stabilizing or a destabilizing agent for a specific enzyme depending on its concentration, inactivation pH and immobilization protocol. Using lipases, (NH₄)₂SO₄ generally permits the highest stabilities (although this is not a universal rule), but using the other enzymes this salt is in many instances a destabilizing agent. At pH 9.0, it is more likely to find a salt destabilizing effect than at pH 7.0. Results confirm the difficulty of foreseeing the effect of high concentrations of salts in a specific immobilized enzyme.

Immobilization of thermolysin enzyme on dendronized silica supports. Evaluation of its feasibility on multiple protein hydrolysis cycles

This work evaluates different dendrimer-silica supports for the immobilization of enzymes by multipoint covalent binding. Thermolysin was immobilized on two dendrimers (PAMAM and carbosilane) with two different generations (zero (G0) and first (G1)). Results were compared with a control, a silica support functionalized with a monofunctional molecule. Dendrimers increased the number of available sites to bind the enzyme. Despite the enzyme was immobilized on all supports, G0 dendrimers immobilized a 30% more enzyme than G1. Thermolysin immobilized on G0 dendrimer supports showed the highest activity and could be employed in three consecutive hydrolysis cycles. Optimal immobilization time was 1 h while optimal protein loading was 25 mg enzyme/100 mg support. Enzyme activity was promoted when using 5 mg of immobilized enzyme at 750 rpm, 60 °C, and 2 h of hydrolysis. Under these conditions, the activity of thermolysin increased up to the 78% of the free enzyme activity. Kinetics of the hydrolysis reaction using the immobilized thermolysin was also studied and compared with the obtained using the free thermolysin. The addition of ZnCl₂ and NaCl during the immobilization procedure increased thermolysin activity in the second (22% more) and in the third (14% more) hydrolysis clycles.

Use of Alcalase in the production of bioactive peptides: A review

This review aims to cover the uses of the commercially available protease Alcalase in the production of biologically active peptides since 2010. Immobilization of Alcalase has also been reviewed, as immobilization of the enzyme may improve the final reaction design enabling the use of more drastic conditions and the reuse of the biocatalyst. That way, this review presents the production, via Alcalase hydrolysis of different proteins, of peptides with antioxidant, angiotensin I-converting enzyme inhibitory, metal binding, antidiabetic, anti-inflammatory and antimicrobial activities (among other bioactivities) and peptides that improve the functional, sensory and nutritional properties of foods. Alcalase has proved to be among the most efficient proteases for this goal, using different protein sources, being especially interesting the use of the protein residues from food industry as feedstock, as this also solves nature pollution problems. Very interestingly, the bioactivities of the protein hydrolysates further improved when Alcalase is used in a combined way with other proteases both in a sequential way or in a simultaneous hydrolysis (something that could be related to the concept of combi-enzymes), as the combination of proteases with different selectivities and specificities enable the production of a larger amount of peptides and of a smaller size.

Glyoxyl-Activated Agarose as Support for Covalently Link Novo-Pro D: Biocatalysts Performance in the Hydrolysis of Casein

This study aimed to evaluate the performance of a commercial protease (Novo-Pro D (NPD)), both in soluble and immobilized forms, in the hydrolysis of proteins (using casein as model protein). Immobilization of the protease NPD on 6% agarose activated with glyoxyl groups for 24 h at 20 °C and pH 10.0 allowed preparing immobilized biocatalyst with around 90% immobilization yield, 92% recovered activity versus small substrate, and a thermal stability 5.3-fold higher than the dialyzed soluble enzyme at 50 °C and pH 8.0. Immobilization times longer than 24 h lead to a decrease in the recovered activity and did not improve the biocatalyst stability. At 50 °C and pH 6.5, the immobilized NPD was around 20-fold more stable than the dialyzed soluble protease. Versus casein, the immobilized NDP presented a 10% level of activity, but it allowed hydrolyzing casein (26 g/L) at 50 °C and pH 6.5 up to a 40% degree of hydrolysis (DH) after 2 h reaction, while under the same conditions, only a 34% DH was achieved with soluble NPD. In addition, the immobilized NPD showed good reusability, maintaining the DH of casein for at least ten 2h-reaction batches.

Competitive method for fluorescent dopamine detection in cerebrospinal fluid based on the peroxidase-like activity of ficin

Dopamine (DA), a catecholamine neurotransmitter, is considered to be an important indicator for mental diseases detection in the clinic. In this study, a novel fluorescent sensing platform consisting of the ficin-H₂O₂-tyramine system for determining DA in cerebrospinal fluids (CSF) was established. The proposed method is based on the fact that ficin, a mimetic peroxidase, can catalyze H₂O₂ decomposition into OH radicals, which can oxidize non-fluorescent tyramine into fluorescent dityramine. When DA was introduced, DA can compete with tyramine for OH and resulting in the oxidation reaction of tyramine inhibited along with the fluorescence intensity of the system decreased, which provides a unique strategy for fluorescence detection of DA. Under optimal conditions, the fluorescence intensity decreased linearly with the DA level over a wide concentration range from 0.05 to 12.0 μM (R² = 0.995) with a detection limit of 46 nM (3σ/k). More importantly, the proposed sensing approach exhibits high sensitivity, good selectivity and has been successfully applied to DA sensing in complex biological samples, which made it hold great potential for DA determination in chemical and biological analytical applications.

Synthesis of paramagnetic dendritic silica nanomaterials with fibrous pore structure (Fe3O4@KCC-1) and their application in immobilization of lipase from Candida rugosa with enhanced catalytic activity and stability

Paramagnetic mesoporous fibrous silica (Fe₃O₄@KCC-1) was prepared and its surface was functionalized with 3-aminopropyltriethoxysilane (APTES).