Polymers of phenylenediamines

Molecularly Imprinted Polymer-Based Electrochemical Sensor for the Detection of Azoxystrobin in Aqueous Media

This work presents an electrochemical sensor detecting a fungicide-azoxystrobin (AZO) in aqueous environments. This AZO sensor utilizes a thin-film metal electrode (TFME) combined with an AZO-selective molecularly imprinted polymer (AZO-MIP). The AZO-MIP was directly generated on TFME through electrochemical polymerization from the solution containing two functional monomers: aniline (Ani) and m-phenylenediamine (mPD), and the template: AZO, which was afterwards removed to form AZO-selective cavities in the polymer matrix. The AZO-MIP preparation was characterized by electrochemical and ellipsometry measurements. Optimization of the synthesis parameters, including the charge density applied during electrodeposition, the monomer-to-template ratio, was performed to enhance the sensor's performance. The results demonstrated that the AZO sensor achieved a low limit of detection (LOD) of 3.6 nM and a limit of quantification (LOQ) of 11.8 nM in tap water, indicating its sensitivity in a complex aqueous environment. The sensor also exhibited satisfactory selectivity for AZO in both ultrapure and tap-water samples and achieved a good recovery (94-119%) for the target analyte. This study highlights the potential of MIP-based electrochemical sensors for the rapid and accurate detection of fungicide contaminants in water, contributing to the advancement of analytical tools for water-quality monitoring and risk assessment.

Conjugated Polymers for Aptasensing Applications

Rapid and specific assaying of molecules that report on a pathophysiological condition, environmental pollution, or drug concentration is pivotal for establishing efficient and accurate diagnostic systems. One of the main components required for the construction of these systems is the recognition element (receptor) that can identify target analytes. Oligonucleotide switching structures, or aptamers, have been widely studied as selective receptors that can precisely identify targets in different analyzed matrices with minimal interference from other components in an antibody-like recognition process. These aptasensors, especially when integrated into sensing platforms, enable a multitude of sensors that can outperform antibody-based sensors in terms of flexibility of the sensing strategy and ease of deployment to areas with limited resources. Research into compounds that efficiently enhance signal transduction and provide a suitable platform for conjugating aptamers has gained huge momentum over the past decade. The multifaceted nature of conjugated polymers (CPs), notably their versatile electrical and optical properties, endows them with a broad range of potential applications in optical, electrical, and electrochemical signal transduction. Despite the substantial body of research demonstrating the enhanced performance of sensing devices using doped or nanostructure-embedded CPs, few reviews are available that specifically describe the use of conjugated polymers in aptasensing. The purpose of this review is to bridge this gap and provide a comprehensive description of a variety of CPs, from a historical viewpoint, underpinning their specific characteristics and demonstrating the advances in biosensors associated with the use of these conjugated polymers.

One-Step Accelerated Synthesis of Conducting Polymer/Silver Composites and Their Catalytic Reduction of Cr(VI) Ions and p-Nitrophenol

In this paper, silver nitrate was used as an oxidant to prepare polyaniline, polypyrrole, and poly(3,4-ethylene dioxythiophene)/silver composites through a simultaneous oxidation/reduction process. In addition, p-phenylenediamine was added with 1 mole% relative to the concentrations of the monomers to accelerate the polymerization reaction. The prepared conducting polymer/silver composites were characterized by scanning and transmission electron microscopies to study their morphologies; Fourier-transform infrared and Raman spectroscopies to confirm their molecular structures; and thermogravimetric analysis (TGA) to study their thermal stabilities. The silver content in the composites was estimated by energy-dispersive X-ray spectroscopy, ash analysis, and TGA. The conducting polymer/silver composites were utilized for the remediation of water pollutants through catalytic reduction. Hexavalent chromium ions (Cr(VI)) were photocatalytically reduced to trivalent chromium ions, and p-nitrophenol was catalytically reduced to p-aminophenol. The catalytic reduction reactions were found to follow the first-order kinetic model. Among the prepared composites, polyaniline/silver composite has shown the highest activity for the photocatalytic reduction of Cr(VI) ions with an apparent rate constant of 0.226 min^-1 and efficiency of 100% within 20 min. Additionally, poly(3,4-ethylene dioxythiophene)/silver composite showed the highest catalytic activity towards the reduction of p-nitrophenol with an apparent rate constant of 0.445 min^-1 and efficiency of 99.8% within 12 min.

Recent Advances in the Removal of Organic Dyes from Aqueous Media with Conducting Polymers, Polyaniline and Polypyrrole, and Their Composites

Water pollution by organic dyes, and its remediation, is an important environmental issue associated with ever-increasing scientific interest. Conducting polymers have recently come to the forefront as advanced agents for removing dye. The present review reports on the progress represented by the literature published in 2020–2022 on the application of conducting polymers and their composites in the removal of dyes from aqueous media. Two composites, incorporating the most important polymers, polyaniline, and polypyrrole, have been used as efficient dye adsorbents or photocatalysts of dye decomposition. The recent application trends are outlined, and future uses also exploiting the electrical and electrochemical properties of conducting polymers are offered.

Revisiting the Structure and Electrochemical Performance of Poly(o-phenylenediamine) as an Organic Cathode Material

Poly(o-phenylenediamine) (PoPDA) has been recognized as a low-cost electroactive organic material and studied as a cathode for aqueous zinc batteries or as an anode for nonaqueous lithium batteries. However, there remains a lot of confusion about its synthesis, structure, and electrochemical application. Especially, the previously studied PoPDA samples were mostly synthesized at room temperature, which were proved by us to be just a dimer, that is, 2,3-diaminophenazine (DAPZ). By various characterization methods including elemental analysis and mass spectrometry, we verified that the product synthesized at high temperature, PoPDA-H, was a polymer based on DAPZ as the structural repeat unit and with some imperfect substitutes (OH and NH₃⁺CH₃COO^-). Based on the reversible redox reaction of phenazine units and the stable polymer structure within 1.3-3.8 V vs Li⁺/Li, PoPDA-H was more appropriate to be applied as a cathode rather than as an anode for lithium batteries. It achieved a high energy density of 490 Wh kg^-1 (2.12 V × 231 mAh g^-1) at 50 mA g^-1 and a high cycling stability (79%@1000th cycle) at 500 mA g^-1, both of which were comparable to previously reported expensive pyrazine- and carbonyl-based polymers. This work clarifies many misunderstandings of PoPDA, which is important to its further development toward practical application in energy-storage devices.

Development of Fluorescent Carbon Nanoparticle-Based Probes for Intracellular pH and Hypochlorite Sensing

Acid-base and redox reactions are important mechanisms that affect the optical properties of fluorescent probes. Fluorescent carbon nanoparticles (CNPs) that possess tailored surface functionality enable a prompt response to regional stimuli, offering a useful platform for detection, sensing, and imaging. In this study, mPA CNPs were developed through one-pot hydrothermal reaction as a novel fluorescent probe (quantum yield = 10%) for pH and hypochlorite sensing. m-Phenylenediamine was chosen as the major component of CNPs for pH and hypochlorite responsiveness. Meanwhile, ascorbic acid with many oxygen-containing groups was introduced to generate favorable functionalities for improved water solubility and enhanced sensing response. Thus, the mPA CNPs could serve as a pH probe and a turn-off sensor toward hypochlorite at neutral pH through fluorescence change. The as-prepared mPA CNPs exhibited a linear fluorescence response over the pH ranges from pH 5.5 to 8.5 (R2 = 0.989), and over the concentration range of 0.125–1.25 μM for hypochlorite (R2 = 0.985). The detection limit (LOD) of hypochlorite was calculated to be 0.029 μM at neutral pH. The mPA CNPs were further applied to the cell imaging. The positively charged surface and nanoscale dimension of the mPA CNPs lead to their efficient intracellular delivery. The mPA CNPs were also successfully used for cell imaging and sensitive detection of hypochlorite as well as pH changes in biological systems. Given these desirable performances, the as-synthesized fluorescent mPA CNPs shows great potential as an optical probe for real-time pH and hypochlorite monitoring in living cells.

Unveiling the Actual Catalytic Sites in Nanozyme-Catalyzed Oxidation of o-Phenylenediamine

Nanozymes have offered remarkable advantages over natural enzymes and found widespread applications including biosensors, immunoassays, nanomedicines, and environmental remediation. Oxidation of o-phenylenediamine (OPD) by nanozymes has been listed as a standard protocol for determining nanozyme activities. Given the complexity of OPD oxidation processes, however, the mechanism of nanozyme-catalyzed oxidation of OPD remains elusive. In this report, mechanistic studies of nanozyme-catalyzed oxidation of OPD are performed and a distinguishably different mechanism from that of natural enzymes is found. A combination of Fourier transform infrared spectroscopy, nuclear magnetic resonance, electrospray ionization mass spectrometry, and electron microscopic studies provides compelling evidence that polymerization of OPD occurs on the surface of several different nanozymes. The unexpected polymerization causes a dense coating layer of poly(o-phenylenediamine) (POPD) on nanozymes renders the intrinsic properties of nanozymes. Therefore, this fundamental discovery raise serious concerns using OPD-based colorimetric method for determining nanozyme activities. Without examining the surface change of nanozymes after catalytic reactions, the use of OPD-based colorimetric method for determining nanozyme activities is strongly discouraged. Furthermore, POPD is discovered as a new oxidase mimic, and this new mechanism also provides a general and robust method to coat nanomaterials with POPD polymers of enzyme-mimicking properties.

Peculiarities of Oxidative Polymerization of Diarylaminodichlorobenzoquinones

New oxidative polymerization monomers-diarylaminodichlorobenzoquinones were synthesised by alkylating aniline, m-phenylenediamine and methanilic acid with chloranil. Oxidative polymerization of diarylaminodichlorobenzoquinones was studied for the first time in relation to the concentration of the monomer, acid, and oxidant/monomer ratio. It was found that the synthesized monomers are highly active in the polymerization reaction, and the oxidation rate grows with the increase in the acid concentration. Only one arylamine group is involved in the polymerization reaction. The optimal oxidant/monomer ratio is stoichiometric for one arylamine group, despite the bifunctionality of the monomers. It was shown that the type of the substituent in the aniline ring (electron donor or electron acceptor) determines the growth of the polymer chain and the structure of the resulting conjugated polymers. A mechanism for the formation of active polymerization centers for diarylaminodichlorobenzoquinones was proposed. FTIR-, NMR-, X-ray photoelectron spectroscopy, and SEM were used to identify the structure of the synthesized monomers and polymers. The obtained polymers have an amorphous structure and a loose globular morphology. The frequency dependence of the electrical conductivity was studied.

Synthesis and Impedance Spectroscopy of Poly(p-phenylenediamine)/Montmorillonite Composites

Poly(p-phenylenediamine)/montmorillonite (PPDA/MMT) composites were prepared by the oxidative polymerization of monomers intercalated within the MMT gallery, using ammonium peroxydisulfate as an oxidant. The intercalation process was evidenced by X-ray powder diffraction. The FT-IR and Raman spectroscopies revealed that, depending on the initial ratio between monomers and MMT in the polymerization mixture, the polymer or mainly oligomers are created during polymerization. The DC conductivity of composites was found to be higher than the conductivity of pristine polymer, reaching the highest value of 10^-6 S cm^-1 for the optimal MMT amount used during polymerization. Impedance spectroscopy was performed over wide frequency and temperature ranges to study the charge transport mechanism. The data analyzed in the framework of conductivity formalism suggest different conduction mechanisms for high and low temperature regions.

Synthesis of Fe Doped Poly p-Phenylenediamine Composite: Co-Adsorption Application on Toxic Metal Ions (F- and As3+) and Microbial Disinfection in Aqueous Solution

Water is regarded as an important natural resource to sustain life, and its purification is an important criterion that determines its quality and usefulness. In this study, the incorporation of Fe³⁺ oxide onto a phenylenediamine (pPD) polymer matrix through chemical co-polymerization was prepared, and its arsenite and fluoride removal potentials at optimal conditions from aqueous solution were evaluated. The morphology and structural analysis of the synthesized Fe-doped pPD (Fe-pPD) were comparatively evaluated using the FT-IR, SEM, EDS, and XRD techniques. Fe was successfully incorporated onto pPD matrix as confirmed by different morphological characterizations. The rate of adsorption of F⁻ and As³⁺ onto the Fe-pPD composite best followed the pseudo-second-order kinetic model. The experimental data for both As³⁺ and F⁻ onto the Fe-pPD composite better fit the Freundlich isotherm model at different operating temperatures. Overall, the synthesized composite exhibited a strong affinity towards fluoride uptake (96.6%) than arsenite uptake (71.14%) with a maximum capacity of 6.79 (F⁻) and 1.86 (As³⁺) mg/g. Additionally, the synthesized adsorbent showed some level of antimicrobial activity against common water-borne bacterial. Therefore, the Fe-doped pPD composite has the potential ability for inorganic metal species pollutants remediation and bacterial disinfection in community-level water purification processes.

Carbon Materials Derived from Poly(aniline-co-p-phenylenediamine) Cryogels

Nitrogen-containing carbon derivatives were prepared by the carbonization of poly(aniline-co-p-phenylenediamine) cryogels in inert atmosphere. Lower aniline fraction in the comonomer mixture used for preparation of the cryogels led to the decrease of their thermal stability, a consequent increase of carbonization degree, and less defective structure of carbonized materials. The resulting carbonaceous products had up to 4 orders of magnitude higher specific surface area than their respective cryogel precursors, the highest value 931 m² g^-1 being achieved for carbonized poly(p-phenylenediamine) cryogel. Electrochemical characterization of the carbon derivatives demonstrated that the decrease in aniline concentration during the synthesis of the precursor cryogels led to higher gravimetric capacitance for corresponding carbonized materials. These materials can potentially be used for energy storage applications.

A dual-step immobilization/imprinting approach to prepare magnetic molecular imprinted polymers for selective removal of human serum albumin

One viable solution to improve the conformational stability of template proteins is to use multiple, weaker modes of action to immobilize proteins on the surfaces of a solid support. Herein, we introduce a novel surface imprinting technique for human serum albumin (HSA) by a dual immobilization/imprinting strategy. Specifically, HSA was first conjugated to the surfaces of magnetic Fe₃O₄ nanoparticles through a reversible aldmine condensation reaction. Dopamine (DA) was then used to imprint the protein template via an auto-polymerization reaction in biocompatible aqueous media. The resultant magnetic molecular imprinted polymers (MMIPs) possess high adsorption capacity (70.2 mg g^-1), superior selectivity (IF = 4.54), and rapid capturing kinetics to HSA (within 20 min). We successfully demonstrate the practical applicability of MMIPs to the selective removal of HSA from human serum sample. Our work offers a novel and robust solution to develop proteins imprinted materials with high binding capacity and selectivity. We anticipate such materials will find wide applications to protein detection or removal in diverse real-life clinical and biological samples.

The chemistry of Cr(VI) adsorption on to poly(p-phenylenediamine) adsorbent

Water pollution due to industrial processes has necessitated and spurred robust research into the development of adsorbent materials for remediation. Polyphenylenediamines (PPD) have attracted significant attention because of their dual cationic and redox properties. They are able to reduce Cr(VI) to Cr(III) in solution. Interrogation of the chemical processes involved in the Cr(VI) adsorption on para-PPD was primarily by X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FT-IR) spectroscopy. It was confirmed that the underlying oxidation of the amino groups to imines during the reduction of Cr(VI) to Cr(III) was irreversible. This process occurred at both acidic and alkaline conditions. Reduction was accompanied by Cr(III) chelation on the adsorbent surface. Further, regeneration with dilute aqueous NaOH and HCl extended the polymer's adsorptive capacity beyond exhaustion of its redox potentials.

Smart and Functional Conducting Polymers: Application to Electrorheological Fluids

Electro-responsive smart electrorheological (ER) fluids consist of electrically polarizing organic or inorganic particles and insulating oils in general. In this study, we focus on various conducting polymers of polyaniline and its derivatives and copolymers, along with polypyrrole and poly(ionic liquid), which are adopted as smart and functional materials in ER fluids. Their ER characteristics, including viscoelastic behaviors of shear stress, yield stress, and dynamic moduli, and dielectric properties are expounded and appraised using polarizability measurement, flow curve testing, inductance-capacitance-resistance meter testing, and several rheological equations of state. Furthermore, their potential industrial applications are also covered.

Tuning the optical properties of poly(o-phenylenediamine-co-pyrrole) via template mediated copolymerization

Tailoring of conjugated monomers via copolymerization is a facile method to obtain tunable spectral, morphological and optical properties. To investigate the effect of copolymerization of pyrrole with o-phenylenediamine on the optoelectronic properties of the synthesized copolymers, the present work reports the synthesis of copolymers of o-phenylenediamine with pyrrole with varying mol ratios via chemical polymerization in methylene blue (MB) medium. Copolymerization was confirmed by Fourier transform infrared spectroscopy and ultraviolet-visible studies. Ultraviolet-visible spectroscopy revealed variation in the optical properties with the change in the monomer ratio. Fluorescence studies showed that the copolymer containing 80% poly(o-phenylenediamine) revealed highest quantum yield among all the copolymers. The emission color could therefore be tuned by careful selection of narrow band co-monomers, which could help in designing tunable fluorescence emitting materials for potential application in OLED devices.

Sensing CA 15-3 in point-of-care by electropolymerizing O-phenylenediamine (oPDA) on Au-screen printed electrodes

This work presents an alternative device for cancer screening in liquid biopsies. It combines a biomimetic film (i) with electrochemical detection (ii). The biomimetic film (i) was obtained by electro-polymerizing amine-substituted benzene rings around a CA 15–3 target. This protein target was previously adsorbed on a gold (Au) support and incubated in charged monomers (4-Styrenesulfonate sodium and 3-Hydroxytyraminium chloride). The protein was further eliminated by enzymatic activity, leaving behind vacant sites for subsequent rebinding. Electrochemical detection (ii) was achieved on an Au working electrode, designed on commercial screen-printed electrodes. Raman spectroscopy, atomic force microscopy and ellipsometric readings were used to follow the chemical modification of the Au surface. The ability of the material to rebind CA15-3 was monitored by electrochemical techniques. The device displayed linear responses to CA15-3 ranging from 0.25 to 10.00 U/mL, with detection limits of 0.05 U/mL. Accurate results were obtained by applying the sensor to the analysis of CA15-3 in PBS buffer and in serum samples. This biosensing device displayed successful features for the detection of CA 15–3 and constitutes a promising tool for breast cancer screening procedures in point-of-care applications. Moreover, its scale-up seems feasible as it contains a plastic antibody assembled in situ, in less than 1 minute, and the analysis of serum takes less than 30 minutes.

Improvement of amperometric transducer selectivity using nanosized phenylenediamine films

In this work, we studied the conditions of deposition of a semipermeable polyphenylenediamine (PPD)-based membrane on amperometric disk platinum electrodes. Restricting an access of interfering substances to the electrode surface, the membrane prevents their impact on the sensor operation. Two methods of membrane deposition by electropolymerization were compared-at varying potential (cyclic voltammetry) and at constant potential. The cyclic voltammetry was shown to be easier in performing and providing better properties of the membrane. The dependence of PPD membrane effectiveness on the number of cyclic voltammograms and phenylenediamine concentration was analyzed. It was shown that the impact of interfering substances (ascorbic acid, dopamine, cysteine, uric acid) on sensor operation could be completely avoided using three cyclic voltammograms in 30 mM phenylenediamine. On the other hand, when working with diluted samples, i.e., at lower concentrations of electroactive substances, it is reasonable to decrease the phenylenediamine concentration to 5 mM, which would result in a higher sensitivity of transducers to hydrogen peroxide due to a thinner PPD layer. The PPD membrane was tested during continuous operation and at 8-day storage and turned out to be efficient in sensor and biosensors.