Nanosecond laser ablation assisted the enhancement of antibacterial activity of copper oxide nano particles embedded though Polyethylene Oxide/Polyvinyl pyrrolidone blend matrix

Surface antibacterial properties enhanced through engineered textures and surface roughness: A review

The spread of bacteria through contaminated surfaces is a major issue in healthcare, food industry, and other economic sectors. The widespread use of antibiotics is not a sustainable solution in the long term due to the development of antibiotic resistance. Therefore, surfaces with antibacterial properties have the potential to be a disruptive approach to combat microbial contamination. Different methods and approaches have been studied to impart or enhance antibacterial properties on surfaces. The surface roughness and texture are inherent parameters that significantly impact the antibacterial properties of a surface. They are also directly related to the previously employed machining and treatment methods. This review article discusses the correlation between surface roughness and antibacterial properties is presented and discussed. It begins with an introduction to the concepts of surface roughness and texture, followed by a description of the most commonly utilized machining methods and surface. A thorough analysis of bacterial adhesion and growth is then presented. Finally, the most recent studies in this research area are comprehensively reviewed. The studies are sorted and classified based on the utilized machining and treatment methods, which are divided into mechanical processes, surface treatments and coatings. Through the systematic review and record of the recent advances, the authors aim to assist and promote further research in this very promising and extremely important direction, by providing a systematic review of recent advances.

Greener microwave synthesized Se nanospheres for antioxidant, cell viability, and antibacterial effect

Selenium nanocrystals (SeNPs) were developed using Coccinia grandis fruit (CGF) extract by green microwave approach. The morphological characters revealed that the quasi SeNPs with dimensions ranging from 12 to 24 nm have been arranged in encapsulated spherical geometries with dimensions ranging from 0.47 to 0.71 m. The DPPH assay revealed that SeNPs at a concentration of 70 µl of 99.2% had the greatest possible scavenging capacity. The nanoparticle concentrations were around 500 g/mL and the cellular uptake of SeNPs through living thing extracellular matrix cell lines in vitro was limited to 75.1 ± 3.8%. The biocidal activity was tested against E. coli, B. cereus, and S. aureus strains. Since it had the greatest MIC against B. cereus with 32 mm compared with the reference antibiotics. These incredible qualities of SeNPs suggest that attempting to manipulate multi-purpose nanoparticles for powerful and flexible wound and skin therapeutic innovations is very impressive.

Graphical abstract

Femtosecond laser treatment promotes the surface bioactivity and bone ingrowth of Ti6Al4V bone scaffolds

In this study, a femtosecond laser with a wavelength of 800 nm was used to modify the surface of a titanium alloy bone scaffold created via selective laser melting (SLM). The outcomes demonstrated that the surface morphology of the bone scaffold after femtosecond laser treatment was micro-nano morphology. The hydrophobic structure of the scaffold was changed into a super-hydrophilic structure, improving the surface roughness, which was highly helpful for osteoblast adhesion and differentiation. The femtosecond laser surface treatment in vitro samples produced a thick layer of hydroxyapatite (HAP) with improved surface bioactivity. The effectiveness of osseointegration and interstitial growth of the specimens treated with the femtosecond laser surface were found to be better when bone scaffolds were implanted into the epiphysis of the tibia of rabbits. As a result, femtosecond laser therapy dramatically enhanced the surface activity of bone scaffolds and their capacity to integrate with the surrounding bone tissues, serving as a trustworthy benchmark for future biological scaffold research.

A Review on Antibacterial Biomaterials in Biomedical Applications: From Materials Perspective to Bioinks Design

In tissue engineering, three-dimensional (3D) printing is an emerging approach to producing functioning tissue constructs to repair wounds and repair or replace sick tissue/organs. It allows for precise control of materials and other components in the tissue constructs in an automated way, potentially permitting great throughput production. An ink made using one or multiple biomaterials can be 3D printed into tissue constructs by the printing process; though promising in tissue engineering, the printed constructs have also been reported to have the ability to lead to the emergence of unforeseen illnesses and failure due to biomaterial-related infections. Numerous approaches and/or strategies have been developed to combat biomaterial-related infections, and among them, natural biomaterials, surface treatment of biomaterials, and incorporating inorganic agents have been widely employed for the construct fabrication by 3D printing. Despite various attempts to synthesize and/or optimize the inks for 3D printing, the incidence of infection in the implanted tissue constructs remains one of the most significant issues. For the first time, here we present an overview of inks with antibacterial properties for 3D printing, focusing on the principles and strategies to accomplish biomaterials with anti-infective properties, and the synthesis of metallic ion-containing ink, chitosan-containing inks, and other antibacterial inks. Related discussions regarding the mechanics of biofilm formation and antibacterial performance are also presented, along with future perspectives of the importance of developing printable inks.

A Contrastive Study of Self-Assembly and Physical Blending Mechanism of TiO2 Blended Polyethersulfone Membranes for Enhanced Humic Acid Removal and Alleviation of Membrane Fouling

In this study, membrane fabrication was achieved by two different methods: (i) self-assembly and (ii) physical blending of TiO₂ in PES membrane for humic acid filtration. The TiO₂ nanoparticles were self-assembled by using TBT as the precursor and pluronic F127 as triblock copolymers around the membrane pores. This was achieved by manipulating the hydrolysis and condensation reaction of TBT precursors during the non-solvent induced phase separation (NIPS) process. On the other hand, the TiO₂ was physically blended as a comparison to the previous method. The characteristic of the membrane was analysed to explore the possibility of enhancing the membrane antifouling mechanism and the membrane flux. The membrane morphology, pore size, porosity, and contact angle were characterised. Both methods proved to be able to enhance the antifouling properties and flux performance. The HA rejection increased up to 95% with membrane flux 55.40 kg m⁻² h⁻¹. The rejection rate was not significantly improved for either method. However, the antifouling characteristic for the self-assembly TiO₂/PES membrane was better than the physically blended membrane. This was found to be due to the high surface hydrophilicity of the MM membrane, which repelled the hydrophobic HA and consequently blocked the HA adsorption onto the surface.

Preparation of mesoporous silica-based nanocomposites with synergistically antibacterial performance from nano-metal (oxide) and polydopamine

In this work, a novel antibacterial nanocomposite system was developed using mesoporous silica (MSN) as an effective nanocarrier, and the resultant nanocomposites demonstrated remarkable antibacterial performance due to the synergistic effect among nano zinc oxides, silver nanoparticles, and polydopamine (PDA). The successful synthesis of MSN/ZnO@PDA/Ag nanocomposites was confirmed. The physicochemical properties and the morphologies of these nanocomposites were investigated. It was found that the particle size increased along with the evolution of these nanocomposites. Besides, nano zinc oxides were formed in the nanochannels of mesoporous silica with a particle size about 2 nm, and that of silver nanoparticle was less than 50 nm. In addition, the results revealed that the presence of mesoporous silica could effectively prevent the formation of large-size silver nanoparticles and facilitate their well dispersion. Due to the synergistic effect among nano zinc oxides, silver nanoparticles, and polydopamine, these nanocomposites exhibited remarkable antibacterial performance even at a low concentration of 313 ppm, and the antibacterial mechanism was also elucidated. Therefore, this work provides a facile and controllable approach to preparing synergistically antibacterial nanocomposites, and the remarkable antibacterial performance make them suitable for practical applications.

Nanofibrous ε-polycaprolactone scaffolds containing Ag-doped magnetite nanoparticles: Physicochemical characterization and biological testing for wound dressing applications in vitro and in vivo

Skin wounds can lead to numerous complications with dangerous health consequences. In this work, magnetite nanoparticles were doped with different concentrations of antimicrobial silver (Ag) ions and incorporated into the electrospun nanofibrous ε-polycaprolactone (PCL) scaffolds. Nanoparticles and scaffolds with various Ag contents were characterized using a range of physicochemical techniques. Ag entered magnetite as cations and preferentially positioned at tetrahedral sites, introducing lattice distortions and topographic irregularities. Amorphization of the structure due to accommodation of Ag expanded the lattice in the bulk and contracted it on the surface, where broadened distribution of Fe-O coordinations was detected. Promoting spin canting and diminishing the double exchange interaction through altered distribution of ferric and ferrous ions, Ag softened the magnetism of magnetite. By making the nanoparticle structure more defective, Ag modified the interface with the polymer and promoted the protrusion of the nanoparticles from the surface of the polymeric nanofibers, thus increasing their roughness and hydrophilicity, with positive repercussions on cell adhesion and growth. Both the viability of human melanocytes and the antibacterial activity against E. coli and S. aureus increased with the concentration of Ag in the magnetite phase of the scaffolds. Skin wound healing rate in rats also increased in direct proportion with the concentration of Ag in the magnetite phase, and no abnormalities in the dermal and epidermal tissues were visible on day 10 in the treatment group. These results imply an excellent potential of these composite nanofibrous scaffolds for use as wound dressings and in other reconstructive skin therapies.

Polycaprolactone based electrospun matrices loaded with Ag/hydroxyapatite as wound dressings: Morphology, cell adhesion, and antibacterial activity

The development of a scaffold matrix that can inhibit bacterial infection and promote wound healing simultaneously is an essential demand to improve the health care system. Hydroxyapatite (HAP) doped with different concentrations of silver ions (Ag⁺) were incorporated into electrospun nanofibrous scaffolds of polycaprolactone (PCL) using the electrospinning technique. The formed phase was identified using XRD, while the morphological and roughness behavior were investigated using FESEM. It was shown that scaffolds were configured in randomly distributed nanofibers with diameters around of 0.19-0.40, 0.31-0.54, 1.36, 0.122-0.429 μm for 0.0Ag-HAP@PCL, 0.2Ag-HAP@PCL, 0.6Ag-HAP@PCL, and 0.8Ag-HAP@PCL, respectively. Moreover, the maximum roughness peak height increased significantly from 179 to 284 nm, with the lowest and highest contributions of Ag. The mechanical properties were examined and displayed that the tensile strength increased from 3.11 ± 0.21 MPa to its highest value at 3.57 ± 0.31 MPa for 0.4Ag-HAP@PCL. On the other hand, the cell viability also was enhanced with the addition of Ag and improved from 97.1 ± 4.6% to be around 102.3 ± 3.1% at the highest contribution of Ag. The antibacterial activity was determined, and the highest imbibition zones were achieved at the highest Ag dopant to be 12.5 ± 1.1 mm and 11.4 ± 1.5 mm against E. coli and S. aureus. The in vitro cell proliferation was observed through human fibroblasts cell lone (HFB4) and illustrated that cells were able to grow and spread not only on the fibers' surface but also, they were spreading and adhered through the deep pores.

Physical, electrochemical and biological evaluations of spin-coated ε-polycaprolactone thin films containing alumina/graphene/carbonated hydroxyapatite/titania for tissue engineering applications

Composite structures are at the frontier of materials science and engineering and polymeric/ceramic composites present one of their most prospective subsets. Prior studies have shown both improvements and deteriorations of properties of polymers upon the addition of ceramic phases to them, but not many studies have dealt with the direct comparison of chemically distinct inorganic additives. The goal of this study was to compare the properties of ε-polycaprolactone (PCL) thin films supplemented with alumina, graphene, carbonated hydroxyapatite or titania particles, individually, in identical amounts (12 wt%). The composite films were analyzed for their phase composition, grain size, morphology, surface roughness, porosity, cell response, mechanical properties and electrochemical performance. Each additive imparted one or more physical or biological properties onto PCL better than others. Thus, alumina increased the microhardness of the films better than any other additive, with the resulting values exceeding 10 MPa. It also led to the formation of a composite with the least porosity and the greatest stability to degradation in simulated body fluid based on open circuit potential (OCP) measurements and electrochemical impedance spectroscopy (EIS). Titania made the surface of PCL roughest, which in combination with its high porosity explained why it was the most conducive to the growth of human fibroblasts, alongside being most prone to degradation in wet, corrosive environments and having the highest Poisson's ratio. Graphene, in contrast, made the surface of PCL smoothest and the bulk structure most porous, but also most conductive, with the OCP of -37 mV. The OCP of PCL supplemented with carbonated hydroxyapatite had the highest OCP of -134 mV and also the highest mechanical moduli, including the longitudinal (781 MPa), the shear (106 MPa), the bulk (639 MPa), and the elastic (300 MPa). The only benefit of the deposition of multilayered PCL films supplemented with all four inorganic additives was to enable a relatively high resistance to degradation. This study demonstrates that the properties of thin PCL films could be effectively optimized through the simple choice of appropriate inorganic additives dispersed in them. There is no single additive that proves ideal for improving all the properties of interest in PCL thin films, but their choice should be adjusted to the actual application. One such method of compositional optimization could prove crucial in the effort to develop biocomposites for superior performance in tissue engineering applications.