N-vinyl pyrrolidone-assisted free radical functionalization of glycidyl methacrylate onto styrene-b-(ethylene-co-butylene)-b-styrene

High-performance and functional fully bio-based polylactic acid/polypropylene carbonate blends by in situ multistep reaction-induced interfacial control

Using a solvent-free radical grafting technique, glycidyl methacrylate (GMA) and maleic anhydride (MAH) were used as functionalized graft monomers, styrene (St) as a copolymer monomer, and grafted onto polylactic acid (PLA). A series of PLA-g-(GMA/MAH-co-St) graft copolymers were prepared by adjusting the GMA/MAH ratio. Subsequently, the prepared graft copolymers were used as a compatibilizer with PLA and polypropylene carbonate (PPC) for melt blending to prepare PLA/PPC/PLA-g-(GMA/MAH-co-St) blends. The effects of changes in the GMA/MAH ratio in the graft copolymer on the thermodynamics, rheology, optics, degradation performance, mechanical properties, and microstructure of the blend were studied. The results found that GMA, MAH, and St were successfully grafted onto PLA, and the PLA-g-(GMA/MAH-co-St) graft copolymer obtained from the reaction had a good toughening effect on the PLA/PPC blend system, which significantly improved the mechanical properties of the PLA/PPC/PLA-g-(GMA/MAH-co-St) blend without reducing its degradation performance, resulting in a biodegradable blend material with excellent comprehensive performance. In the PLA-g-(GMA/MAH-co-St) grafting reaction system, when GMA/MAH = 1.5/1.5 (w/w), the grafting degree of the graft copolymer increased most significantly, from 0.83 phr to 1.51 phr. This composition of graft copolymer can effectively improve the compatibility between PLA and PPC. The resulting PLA/PPC blend can maintain good melt flow properties (MFR of 14.51 g/10 min), high transparency, and low haze (light transmittance of 91.56 %, haze of 20.5 %), while significantly improving its thermal stability (T95%, Tmax, and Et increased by 12.87 °C, 20.33 °C, and 32.00 kJ/mol, respectively). Moreover, when introducing PLA-g-(GMA/MAH-co-St) (GMA/MAH = 1.5/1.5 (wt/wt)) graft copolymer into the system, the toughness of the PLA/PPC/PLA-g-(GMA/MAH-co-St) blend system is optimal, with the notch impact strength and fracture elongation increasing to 184.6 % and 535.4 % of the PLA/PPC blend, respectively, at which point the fracture surface of the impact sample shows a wrinkled fracture feature indicative of toughness.

The Effect of Functionalized SEBS on the Properties of PP/SEBS Blends

Styrene (St) was used as comonomer and glycidyl methacrylate (GMA) as grafting monomer to prepare SEBS-g-(GMA-co-St) graft copolymers via melt grafting. Then, the graft copolymers were employed as a compatibilizer for melt blending polypropylene (PP) and hydrogenated styrene-butadiene-styrene (SEBS) triblock copolymers. The effects of the amount of GMA in the graft copolymers on thermal properties, rheology, crystallization, optical and mechanical properties, and microstructure of the blends were investigated. The results show that GMA and St were successfully grafted onto SEBS. The GMA amount in the graft copolymer significantly influenced the comprehensive properties of PP/SEBS/SEBS-g-(GMA-co-St) blends. The epoxy groups of GMA reacted with PP and SEBS, forming interfacial chemical bonds, thereby enhancing the compatibility between PP and SEBS to varying extents. After introducing SEBS-g-(GMA-co-St) into PP/SEBS blends, crystallinity decreased, crystal size increased while transmittance remained above 91% with rising GMA amount in the graft copolymers, indicating excellent optical properties. Notched impact strength and elongation at break of the blends showed a trend of first increasing and then decreasing with increased amounts of GMA in the graft copolymers. When the amount of GMA in the graft copolymers was 3 wt%, the blends exhibited optimal toughness with notched impact strength and elongation at break of 30,165.82 J/m2 and 1445.40%, respectively. This was attributed to the tightest dispersion interface adhesion and maximum matrix plastic deformation, consistent with the mechanical performance results.

Balancing the decomposable behavior and wet tensile mechanical property of cellulose-based wet wipe substrates by the aqueous adhesive

With the current global outbreak of novel coronaviruses, the fabrication of decomposable wet wipe with sufficient wet strength to meet daily use is promising but still challenging, especially when renewable cellulose was employed. In this work, a decomposable cellulose-based wet wipe substrate is demonstrated by introducing a synthetic N-vinyl pyrrolidone-glycidyl methacrylate (NVP-GMA) adhesive on the cellulose surface. Experimental results reveal that the NVP-GMA adhesive not only significantly facilitates the chemical bonding between cellulose fibers in the wet state, but also increase the surface wettability and water retention. The as-fabricated cellulose-based wet wipe substrate displays a superb water retention capacity of 1.9 times, an excellent water absorption capacity (completely wetted with 0° water contact angle), and a perfect wet tensile index of 3.32 N.m.g⁻¹. It is far better than state-of-the-art wet toilet wipe on the market (non-woven). The prepared renewable and degradable cellulose-based substrate with excellent mechanical strength has potential application prospects in diverse commercially available products such as sanitary and medical wet wipes.

•

A decomposable wet wipe substrate was prepared from the bio-based materials.

•

Synthetic adhesive enhanced the wet strength of the cellulose sheet.

•

Enhancement of cellulose-based material was achieved under aqueous conditions.

•

As-prepared cellulose substrate balanced the dispersibility and wet strength.

Opportunities and challenges for the development of polymer-based biomaterials and medical devices

Biomaterials and medical devices are broadly used in the diagnosis, treatment, repair, replacement or enhancing functions of human tissues or organs. Although the living conditions of human beings have been steadily improved in most parts of the world, the incidence of major human’s diseases is still rapidly growing mainly because of the growth and aging of population. The compound annual growth rate of biomaterials and medical devices is projected to maintain around 10% in the next 10 years; and the global market sale of biomaterials and medical devices is estimated to reach $400 billion in 2020. In particular, the annual consumption of polymeric biomaterials is tremendous, more than 8000 kilotons. The compound annual growth rate of polymeric biomaterials and medical devices will be up to 15–30%. As a result, it is critical to address some widespread concerns that are associated with the biosafety of the polymer-based biomaterials and medical devices. Our group has been actively worked in this direction for the past two decades. In this review, some key research results will be highlighted.