Study of glassy polymers fractional accessible volume (FAV) by extended method of hydrostatic weighing: Effect of porous structure on liquid transport

Influence of Type of Cross-Linking Agent on Structure and Transport Properties of Polydecylmethylsiloxane

The development of membrane materials with high transport and separation properties for the removal of higher hydrocarbons from gas mixtures is an important and complex task. This work examines the effect of a cross-linking agent on the structure and transport properties of polydecylmethylsiloxane (C10), a material characterized by high selectivity towards C3+ hydrocarbons. C10 was cross-linked with various diene hydrocarbons, such as 1,7-octadiene (C10-OD), 1,9-decadiene (C10-DD), 1,11-dodecadiene (C10-DdD), and vinyl-terminated polysiloxanes, of different molecular weights: 500 g/mol (C10-Sil500) and 25,000 g/mol (C10-Sil25-OD). Using a number of characterization methods (IR-spectroscopy, WAXS, DSC, toluene sorption, and gas permeability), it was revealed that a change in the type and length of the cross-linking agent (at the same mole concentration of cross-linking agent) led to a significant change in the structure of the polymer material. The nature of cross-linking agent affected the arrangement of the decyl side-groups of the polymer, resulting in noticeable differences in the solubility, diffusivity, permeability, and selectivity of tested gases (N2, CH4, C2H6, and C4H10). For instance, an increase in the length of the hydrocarbon cross-linker was associated with a drop of n-butane permeability from 5510 (C10-OD) to 3000 Barrer (C10-DdD); however, the transition to a polysiloxane cross-linker led to an increase in corresponded permeability up to 8200 Barrer (C10-Sil25-OD). The n-butane/nitrogen selectivity was significantly higher for diene-type cross-linkers, and the maximum value was achieved for 1,7-octadiene (α(C4H10/N2) = 104).

Removal of dyes using polymers of intrinsic microporosity (PIMs): a recent approach

Removal of dyes from various industrial effluents is a great challenge, and cost-effective methods and materials with high dye removal efficacy are in high demand. Adsorption, nanofiltration and photocatalytic degradation are three major techniques that have been investigated for dye removal. PIMs are promising materials for use in these three methods based on their attributes, such as microporosity, solution processibility, high chemical stability and tunability through facile synthesis and easy postmodification. Although the number of reports on dye removal employing PIMs are limited, some of the materials have been shown to exhibit good dye separation properties, which are comparable to those of the state-of-the-art material activated carbon. In this highlight, we make an account of progress in PIMs and PIM-based composite materials in different dye removal processes over the last decade. Furthermore, we discuss the existing challenges of PIM-based materials and aim to analyze the key parameters for improving their dye removal properties.

Chiral Polymers from Norbornenes Based on Renewable Chemical Feedstocks

Optically active polymers are of great interest as materials for dense enantioselective membranes, as well as chiral stationary phases for gas and liquid chromatography. Combining the versatility of norbornene chemistry and the advantages of chiral natural terpenes in one molecule will open up a facile route toward the synthesis of diverse optically active polymers. Herein, we prepared a set of new chiral monomers from cis-5-norbornene-2,3-dicarboxylic anhydride and chiral alcohols of various natures. Alcohols based on cyclic terpenes ((-)-menthol, (-)-borneol and pinanol), as well as commercially available alcohols (S-(-)-2-methylbutanol-1, S-(+)-3-octanol), were used. All the synthesized monomers were successfully involved in ring-opening metathesis polymerization, affording polymers in high yields (up to 96%) and with molecular weights in the range of 1.9 × 10⁵-5.8 × 10⁵ (M_w). The properties of the metathesis polymers obtained were studied by TGA and DSC analysis, WAXD, and circular dichroism spectroscopy. The polymers exhibited high thermal stability and good film-forming properties. Glass transition temperatures for the prepared polymers varied from -30 °C to +139 °C and, therefore, the state of the polymers changed from rubbery to glassy. The prepared polymers represent a new attractive platform of chiral polymeric materials for enantioselective membrane separation and chiral stationary phases for chromatography.

Membranes Based on PTMSP/PVTMS Blends for Membrane Contactor Applications

In this work, perspective polymeric materials were developed for membrane contactor applications, e.g., for the dissolved oxygen removal from amine CO₂ capture solvents. Several polymeric blends based on poly[1-trimethylsilyl-1-propyne] (PTMSP) and poly[vinyltrimethylsilane] (PVTMS) were studied. The gas and water vapor sorption and permeability coefficients for the PTMSP/PVTMS blend membranes at different PVTMS contents (0-100%) were obtained under temperatures of 30 and 60 °C for the first time. As the PVTMS content increases, the O₂ and CO₂ permeabilities decrease by 160 and 195 times at 30 °C, respectively. The fractional accessible volume of the polymer blends decreases accordingly. The transport of the CO₂ capture solvent vapors through the PTMSP/PVTMS blend membranes were determined in thermo-pervaporation (TPV) mode using aqueous monoethanolamine (30%), N-methyldiethanolamine (40%), and 2-amino-2-methyl-1-propanol (30%) solutions as model amine solvents at 60 °C. The membranes demonstrated high pervaporation separation factors with respect to water, resulting in low amine losses. A joint analysis of the gas permeabilities and aqueous alkanolamine TPV data allowed us to conclude that the polymer blend composition of PTMSP/PVTMS 70/30 provides an optimal combination of a sufficiently high oxygen permeability and the pervaporation separation factor at a temperature of 60 °C.

Hybrid Microporous Polymeric Materials with Outstanding Permeability and Increased Gas Transport Stability: PTMSP Aging Prevention by Sorption of the Polymerization Catalyst on HCPS

The influence of hyper-crosslinked polystyrene (HCPS) Macronet^TM MN200 on the gas transport properties and aging of the highly permeable glassy polymer poly(1-trimethylsilyl-1-propyne) (PTMSP) was studied and analyzed in detail. The gas transport characteristics of dense PTMSP membranes containing 0-10.0 wt % HCPS were studied. It was shown that the introduction of a small amount of HCPS into the PTMSP matrix led to a 50-60% increase of the permeability coefficients of the material for light gases (N₂, O₂, CO₂) and slowed down the deterioration of polymer transport properties over time. The lowest reduction in gas permeability coefficients (50-57%) was found for PTMSP containing HCPS 5.0 wt % after annealing at 100 °C for 300 h. It was found that HCPS sorbed residues of tantalum-based polymerization catalyst from PTMSP. In order to investigate the influence of catalysts on transport and physical properties of PTMSP, we purified the latter from the polymerization catalyst by addition of 5 wt % HCPS into polymer/chloroform solution. It was shown that sorption on HCPS allowed for almost complete removal of tantalum compounds from PTMSP. The membrane made of PTMSP purified by HCPS demonstrated more stable transport characteristics compared to the membrane made of the initial polymer. HCPS has a complex effect on the aging process of PTMSP. The introduction of HCPS into the polymer matrix not only slowed down the physical aging of PTMSP, but also reduced chemical aging due to removal of active reagents.

Combination of the Experimental and Theoretical Approaches for the Estimation of the C1–C4 Alkane Permeability Parameters in Poly (4-Methyl-2-Pentyne) and Poly (4-Methyl-1-Pentene)

Poly (4-methyl-2-pentyne) (PMPentyne) and poly (4-methyl-1-pentene) (PMPentene) as membrane gas-separating media were studied with a combination of experimental and theoretical approaches. Experimental approaches included the permeability measurements for C1–C4 alkanes in linear heating mode (for PMPentyne) and under isothermal conditions (for PMPentene), and diffusivity evaluation by a differential method for PMPentene. Theoretical approaches included the ‘hard-spheres’ theory for calculation of gas solubility in PMPentyne and gas transport theory for two-phase systems for the estimation of the amorphous and crystalline phases contribution in PMPentene. Correlation analysis was used for any type of gas transfer parameter calculation where experimental data were lacking. These combinations of methods allowed obtaining the whole set of parameters for any gas–polymer pairing and explained the butane-selective properties revealed in PMPentyne (C1 < C2 < C3 < C4) and methane-selective properties of PMPentene (C1 > C2 > C3 > C4).

Addition Polyalkylnorbornenes: A Promising New Class of Si-Free Membrane Materials for Hydrocarbons Separation

Nanoporous glassy polymers are perspective materials for the fabrication of gas separation membranes, especially for the application of gaseous hydrocarbon separation. However, the drawback of such materials is the pronounced physical aging resulting in the dramatic drop of gas transport properties due to relaxation of high-free-volume fraction in time. Herein, a novel and readily available group of such glassy polymers is reported based on 5-alkylnorbornenes. These polymers are easily synthesized from dicyclopentadiene and α-olefins by Diels-Alder reaction and vinyl (addition) polymerization of the formed cycloadducts in the presence of ([(η³ -C₃ H₅ )PdCl]₂ /PCy₃ /Na⁺ [B(3,5-(CF₃ )₂ C₆ H₃ )₄ ]^- catalyst. The obtained polymers display low-fraction free volume, stable gas permeability over time, and possess a unique feature for the glassy polymers-solubility controlled permeation of hydrocarbons and enhanced C₄ H₁₀ /CH₄ selectivity.

Mixed-Penetrant Sorption in Ultrathin Films of Polymer of Intrinsic Microporosity PIM-1

Mixed-penetrant sorption into ultrathin films of a superglassy polymer of intrinsic microporosity (PIM-1) was studied for the first time by using interference-enhanced in situ spectroscopic ellipsometry. PIM-1 swelling and the concurrent changes in its refractive index were determined in ultrathin (12-14 nm) films exposed to pure and mixed penetrants. The penetrants included water, n-hexane, and ethanol and were chosen on the basis of their significantly different penetrant-penetrant and penetrant-polymer affinities. This allowed studying microporous polymer responses at diverse ternary compositions and revealed effects such as competition for the sorption sites (for water/n-hexane or ethanol/n-hexane) or enhancement in sorption of typically weakly sorbing water in the presence of more highly sorbing ethanol. The results reveal details of the mutual sorption effects which often complicate comprehension of glassy polymers' behavior in applications such as high-performance membranes, adsorbents, or catalysts. Mixed-penetrant effects are typically very challenging to study directly, and their understanding is necessary owing to a broadly recognized inadequacy of simple extrapolations from measurements in a pure component environment.