Strategic design and synthesis of AIEE (Aggregation Induced Enhanced Emission) active push-pull type pyrene derivatives for the ultrasensitive detection of explosives

Analytical Tools and Methods for Explosive Analysis in Forensics: A Critical Review

This review summarizes (i) compositions and types of improvised explosive devices; (ii) the process of collection, extraction and analysis of explosive evidence encountered in explosive and related cases; (iii) inter-comparison of analytical techniques; (iv) the challenges and prospects of explosive detection technology. The highlights of this study include extensive information regarding the National & International standards specified by USEPA, ASTM, and so on, for explosives detection. The holistic development of analytical tools for explosive analysis ranging from conventional methods to advanced analytical tools is also covered in this article. The most important aspect of this review is to make forensic scientists familiar with the challenges during explosive analysis and the steps to avoid them. The problems during analysis can be analyte-based, that is, interferences due to matrix or added molding/stabilizing agents, trace amount of parent explosives in post-blast samples and many more. Others are techniques-based challenges viz. specificity, selectivity, and sensitivity of the technique. Thus, it has become a primary concern to adopt rapid, field deployable, and highly sensitive techniques.

AIEE Active Azomethine-Based Rhodamine Derivative For Ultrasensitive Multichannel Detection of Au3+ Through a Fluorimetrically, Electrochemically, and RGB-Based Sensing Assay

In this study, a novel rhodamine-based optically and electrochemically active chemosensor, integrated with a p-DMAC moiety, demonstrated extremely selective identification of Au³⁺ ions relative to other metal species, including (Li⁺, Na⁺, K⁺, Ba²⁺, Ca²⁺, Mg²⁺, Co²⁺, Mn²⁺, Zn²⁺, Pb²⁺, Ni²⁺, Fe²⁺, Hg²⁺, Fe³⁺, Cd²⁺, Pd²⁺, Al³⁺, Cr³⁺, Cu²⁺, and nitrate salt of Ag⁺). These compounds demonstrated a novel and outstanding aggregation-induced emission enhancement (AIEE) behavior by aggregating in DMF/H₂O medium. Furthermore, the degree of quenching was varying linearly with a Au³⁺ concentration from 0 to 40 nM, with a lower detection limit by RH-DMAC nanoaggregates of 118.79 picomolar (40.35 ppm). The Stern-Volmer plots, Job's plot, Benesi-Hildebrand plot, ¹H NMR titrations, ESI-mass, and FTIR all revealed significant interactions between the sensor and Au³⁺. Moreover, the proposed electrochemical sensor afforded a linear correlation before the peak current and concentration of Au³⁺ in the range of 0-40 nM, with a detection limit of 483.73 pM or 164.36 ppt (by cyclic voltammetry method) and 298.0 pM or 101.24 ppt (by the Differential Pulse Voltammetry method). Furthermore, the proposed sensing assay was used to measure Au³⁺ ion in spiked water samples (tap, drinking, waste, and river water), achieving acceptable accuracy and precision with high recovery rates. Furthermore, RH-DMAC-coated fluorescence paper test strips were designed for on-site Au³⁺ detection. Apart from this, the use of smartphone-based RGB (Red Green Blue) color analysis shortened the operating process, accelerated the detection technique, and provided a novel methodology for the instantaneous, real-time examination of Au³⁺ in real water samples.

Stimuli-Responsive Electrospun Fluorescent Fibers Augmented with Aggregation-Induced Emission (AIE) for Smart Applications

This review addresses the latest advancements in the integration of aggregation-induced emission (AIE) materials with polymer electrospinning, to accomplish fine-scale electrospun fibers with tunable photophysical and photochemical properties. Micro- and nanoscale fibers augmented with AIE dyes (termed AIEgens) are bespoke composite systems that can overcome the limitation posed by aggregation-caused quenching, a critical deficiency of conventional luminescent materials. This review comprises three parts. First, the reader is exposed to the basic concepts of AIE and the fundamental mechanisms underpinning the restriction of intermolecular motions. This is followed by an introduction to electrospinning techniques pertinent to AIE-based fibers, and the core parameters for controlling fiber architecture and resultant properties. Second, exemplars are drawn from latest research to demonstrate how electrospun nanofibers and porous films incorporating modified AIEgens (especially tetraphenylethylene and triphenylamine derivatives) can yield enhanced photostability, photothermal properties, photoefficiency (quantum yield), and improved device sensitivity. Advanced applications are drawn from several promising sectors, encompassing optoelectronics, drug delivery and biology, chemosensors and mechanochromic sensors, and innovative photothermal devices, among others. Finally, the outstanding challenges together with potential opportunities in the nascent field of electrospun AIE-active fibers are presented, for stimulating frontier research and explorations in this exciting field.

Paper-Based Probes with Visual Response to Vapors from Nitroaromatic Explosives: Polyfluorenes and Tertiary Amines

Although it is well-known that nitroaromatic compounds quench the fluorescence of different conjugated polymers and form colored Meisenheimer complexes with proper nucleophiles, the potential of paper as a substrate for those macromolecules can be further developed. This work undertakes this task, impregnating paper strips with a fluorene-phenylene copolymer with quaternary ammonium groups, a bisfluorene-based cationic polyelectrolyte, and poly(2-(dimethylamino)ethyl methacrylate) (polyDMAEMA). Cationic groups make the aforementioned polyfluorenes attachable to paper, whose surface possesses a slightly negative charge and avoid interference from cationic quenchers. While conjugated polymers had their fluorescence quenched with nitroaromatic vapors in a non-selective way, polyDMAEMA-coated papers had a visual response that was selective to 2,4,6-trinitrotoluene (TNT), and that could be easily identified, and even quantified, under natural light. Far from implying that polyfluorenes should be ruled out, it must be taken into account that TNT-filled mines emit vapors from 2,4-dinitrotoluene (DNT) and dinitrobenzene isomers, which are more volatile than TNT itself. Atmospheres with only 790 ppbv TNT or 277 ppbv DNT were enough to trigger a distinguishable response, although the requirement for certain exposure times is an important limitation.

Highly fluorescent aryl-cyclopentadienyl ligands and their tetra-nuclear mixed metallic potassium-dysprosium clusters

Two alkyl substituted triaryl-cyclopentadienyl ligands [4,4′-(4-phenylcyclopenta-1,3-diene-1,2-diyl)bis(methylbenzene) (1) and 4,4′,4′′-(cyclopenta-1,3-diene-1,2,4-triyl)tris(methylbenzene) (2)] have been synthesized via cross-aldol condensation followed by Zn-dust mediated cyclization and acid catalyzed dehydration reactions. The fluorescence properties of 1 and 2 have been studied in solution and solid state. The ligands exhibited aggregation-induced emission enhancement (AIEE) in THF/water solution. 1 and 2 have been found to be significantly more fluorescent in the solid state than in their respective solutions. This phenomenon can be attributed to the strong intermolecular CH⋯π interactions present in 1 and 2 which leads to the tight packing of molecules in their solid-state. Both 1, 2 and their corresponding anions have been studied by theoretical calculations. Ligands 1 and 2 have been shown to react with anhydrous DyCl₃ in the presence of potassium metal at high temperature to afford two fluorescent chloride-bridged tetra-nuclear mixed potassium–dysprosium metallocenes [(Me₂Cp)₄Dy₂^IIICl₄K₂]·3.5(C₇H₈) (5) and [(Me₃Cp)₄Dy₂^IIICl₄K₂]·3(C₇H₈) (6), respectively in good yields.

Alkyl substituted triaryl-cyclopentadienyl ligands with aggregation-induced emission enhancement (AIEE) properties and their applications in the syntheses of novel chloride bridged tetra-nuclear mixed potassium–dysprosium metallocenes.

Aggregation-Induced Enhanced Emission (AIEE)-Active Conjugated Mesoporous Oligomers (CMOs) with Improved Quantum Yield and Low-Cost Detection of a Trace Amount of Nitroaromatic Explosives

The article reports a straightforward strategy for the design and synthesis of highly luminescent conjugated mesoporous oligomers (CMOs) with an "aggregation-induced enhanced emission" (AIEE) feature through Wittig polymerization of a molecular rotor. Typical molecular rotors such as triphenylamine (TPA) and tetraphenylethene (TPE) as B2-, and A4- and A3-type nodes have been used to construct AIEE-active CMOs, namely, CMO1 and CMO2. The quick dissipation of the excited photons is successfully controlled by the restriction of rotation of the phenyl units through the formation of a mesoporous network scaffold in a solid/thin film, which provides high quantum yields for the interlocked CMO system. Both the CMOs are sensitive and selective to the various nitroaromatic explosives, whereas CMO1 is more sensitive (K_sv = 2.6 × 10⁶ M^-1) toward picric acid. The increased quenching constant for CMO1 is due to its increased quantum yield and high energy-transfer efficiency. The mechanism for sensing has been studied in detail. The larger pore size and pore density in the mesoporous network of CMO1 are found to be responsible for the greater extent of energy transfer from CMO1 to picric acid. Furthermore, CMO1 has been employed for low-cost filter-paper-based detection of a trace amount of nitroaromatic explosive materials.

Interpol review of detection and characterization of explosives and explosives residues 2016-2019

This review paper covers the forensic-relevant literature for the analysis and detection of explosives and explosives residues from 2016-2019 as a part of the 19th Interpol International Forensic Science Managers Symposium. The review papers are also available at the Interpol website at: https://www.interpol.int/Resources/Documents#Publications.