Defluoridation investigation of Yttrium by laminated Y-Zr-Al tri-metal nanocomposite and analysis of the fluoride sorption mechanism

Adsorption of arsenic and fluoride: Modeling of single and competitive adsorption systems

The elevated co-occurrence of arsenic and fluoride in surface and groundwater poses risks to human health in many parts of the world. Using single and competitive batch equilibrium adsorption studies, this research focuses on As(V) and F adsorption by activated carbon and its modeling. BET, XRD, FESEM, EDS, and FTIR analysis were used to discern the structural characteristics of activated carbon. The influence of dosage, pH, and contact time were also investigated in single and simultaneous adsorption systems. The maximum adsorption capacity of activated carbon for arsenic and fluoride were found to be 3.58 mg/g and 2.32 mg/g, respectively. Kinetics studies indicated that pseudo-second-order kinetic model fit better than pseudo-first-order, Elovich, and intraparticle diffusion kinetic models. The non-linear regression analysis of Langmuir, Freundlich, Toth, Redlich Petersons, and Modified Langmuir Freundlich models was used to determine single-component asorption model parameters. Additionally, the simultaneous adsorption was rigorously modeled and compared using the Extended Langmuir (EL), Extended Langmuir Freundlich (ELF), Modified Competitive Langmuir (MCL), and Jeppu Amrutha Manipal Multicomponent (JAMM) isotherm models, and competitive mechanisms were interpreted for the simultaneous adsorption system. Further, the model performances were evaluated by statistical error analysis using the normalized average percentage error (NAPE), root mean square errors (RMSE), and the correlation coefficient (R2). According to the modeling results, single equilibrium data fitted better with the Modified Langmuir Freundlich isotherm model, with a higher R2 of 0.99 and lower NAPE values of 3.8 % and 1.28 % for As(V) and F, than other models. For the binary adsorption, the Extended Langmuir Freundlich isotherm model demonstrated excellent fit with lowest errors. All the competitive isotherm models fit the As(V) and F simultaneous sorption systems reasonably well. Furthermore, the research unveiled a nuanced hierarchy of isotherm fitting, with ELF > EL > MCL > JAMM in varying arsenic at a constant fluoride concentration, and ELF > JAMM > EL > MCL in varying fluoride at a constant arsenic concentrations. In addition, competitive studies divulged crucial insights into selective adsorption, as As(V) exhibits a pronounced adsorption selectivity over F on activated carbon. In essence, As(V) showed a more pronounced antagonistic behavior over F, whereas F exhibited a much lesser competitive behavior in the adsorption of arsenic.

Enhancing fluoride removal from wastewater using Al/Y amended sludge biochar

This study explored the potential of utilizing aluminum and yttrium amended (Al/Y amended) sewage sludge biochar (Al/Y-CSBC) for efficient fluoride removal from wastewater. The adsorption kinetics of fluoride on bimetallic modified Al/Y-CSBC followed the pseudo-second-order model, while the adsorption isotherm conformed to the Freundlich equation. Remarkably, the material exhibited excellent fluoride removal performance over a wide pH range, achieving a maximum adsorption capacity of 62.44 mg·g-1. Moreover, Al/Y-CSBC demonstrated exceptional reusability, maintaining 95% removal efficiency even after six regeneration cycles. The fluoride adsorption mechanism involved ion exchange, surface complexation, and electrostatic adsorption interactions. The activation and modification processes significantly increased the specific surface area of Al/Y-CSBC, leading to a high isoelectric point (pHpzc = 9.14). The incorporation of aluminum and yttrium metals exhibited a novel approach, enhancing the adsorption capacity for fluoride ions due to their strong affinity. Furthermore, the dispersing effect of biochar played a crucial role in improving defluoridation efficiency by enhancing accessibility to active sites. These findings substantiate the significant potential of Al/Y-CSBC for enhanced fluoride removal from wastewater.

Phosphogypsum-Modified Vinasse Shell Biochar as a Novel Low-Cost Material for High-Efficiency Fluoride Removal

In this study, vinasse shell biochar (VS) was easily modified with phosphogypsum to produce a low-cost and novel adsorbent (MVS) with excellent fluoride adsorption performance. The physicochemical features of the fabricated materials were studied in detail using SEM, EDS, BET, XRD, FTIR, and XPS techniques. The adsorption experiments demonstrated that the adsorption capacity of fluoride by MVS was greatly enhanced compared with VS, and the adsorption capacity increased with the pyrolysis temperature, dosage, and contact time. In comparison to chloride and nitrate ions, sulfate ions significantly affected adsorption capacity. The fluoride adsorption capacity increased first and then decreased with increasing pH in the range of 3-12. The fluoride adsorption could be perfectly fitted to the pseudo-second-order model. Adsorption isotherms matched Freundlich and Sips isotherm models well, giving 290.9 mg/g as the maximum adsorption capacity. Additionally, a thermodynamic analysis was indicative of spontaneous and endothermic processes. Based on characterization and experiment results, the plausible mechanism of fluoride adsorption onto MVS was proposed, mainly including electrostatic interactions, ion exchange, precipitation, and hydrogen bonds. This study showed that MVS could be used for the highly efficient removal of fluoride and was compatible with practical applications.

A novel tri-metal adsorbent used for defluoridation technique from groundwater: performance and mechanism

In this research article, a novel adsorbent (Zn-Fe-Al) was synthesized successfully by a simple chemical route where three oxides combined to enhance affinity towards fluoride. The physicochemical properties of the adsorbent were used to characterize and assess its effectiveness in defluoridation with both synthetic and groundwater. The TEM results demonstrated the overlapping of metals, and EDX shows the metals present in the adsorbent. The maximum defluoridation efficiency (97%) of Zn-Fe-Al was obtained at an optimized initial pH 7 and adsorbent dose 0.08 g L-1. The fluoride adsorption on Zn-Fe-Al followed the D-R isotherm and intraparticle diffusion. The maximum adsorption capacity of Zn-Fe-Al was found to be 187 mg g-1. The adsorption of fluoride on Zn-Fe-Al was found to be endothermic and spontaneous. The Zn-Fe-Al adsorbent exhibited satisfactory defluoridation performance on real groundwater. The co-existing ions were also investigated. The adsorption mechanisms for fluoride were electrostatic interaction and ion exchange. These results demonstrated that Zn-Fe-Al adsorbent was considered high potential for effective defluoridation of groundwater.

One-pot solution combustion synthesis of porous spherical-shaped magnesium zinc binary oxide for efficient fluoride removal and photocatalytic degradation of methylene blue and Congo red dye

A novel porous spherical-shaped magnesium zinc binary oxide (MZO) was successfully prepared for the first time using a chemical process for fluoride removal and photocatalytic methylene blue (MB) and Congo red (CR) dye degradation. XRD, FESEM, and TEM were studied for phase formation, topographic, crystallographic, and detailed structural information. The surface charge and optical properties of the adsorbent were studied by zeta potential and photoluminescence spectra. The synthesized nano-adsorbents showed high fluoride removal capacity (43.10 mg/g) and photocatalytic activity with a degradation efficiency of 97.83% and 78.40% for MB and CR, respectively. The adsorption was strongly pH-dependent and worked well in the range 6-9. The kinetic studies were performed for both fluoride removal and dye degradation and were found to follow pseudo-second-order and first-order rate law, respectively. The samples were found to be extremely reusable and selective for fluoride removal in presence of co-ions such as NO₃^-, SO₄^2-, and Cl^-. The basic fluoride adsorption process of the samples can be related to ion exchange and electrostatic interactions, according to XPS and FTIR data. The detailed mechanistic study of photocatalytic dye degradation showed that the reaction occurred via OH radicals. Thus, MZO could be considered an effective and quick adsorbent for water purification in fluoride-containing groundwater and industrial dye wastewater.

Optimization of fluoride removal by Al doped ZnO nanoparticles using response surface methodology from groundwater

The current novel work presents the optimization of factors affecting defluoridation by Al doped ZnO nanoparticles using response surface methodology (RSM). Al doped ZnO nanoparticles were synthesized by the sol-gel method and validated by FTIR, XRD, TEM/EDS, TGA, BET, and particle size analysis. Moreover, a central composite design (CCD) was developed for the experimental study to know the interaction between Al doped ZnO adsorbent dosage, initial concentration of fluoride, and contact time on fluoride removal efficiency (response) and optimization of the process. Analysis of variance (ANOVA) was achieved to discover the importance of the individual and the effect of variables on the response. The model predicted that the response significantly correlated with the experimental response (R² = 0.97). Among the factors, the effect of adsorbent dose and contact time was considered to have more influence on the response than the concentration. The optimized process parameters by RSM presented the adsorbent dosage: 0.005 g, initial concentration of fluoride: 1.5 g/L, and contact time: 5 min, respectively. Kinetic, isotherm, and thermodynamic studies were also investigated. The co-existing ions were also studied. These results demonstrated that Al doped ZnO could be a promising adsorbent for effective defluoridation for water.

A novel carboxylated polyacrylonitrile nanofibrous membrane with high adsorption capacity for fluoride removal from water

To deal with the drinking water safety caused by fluoride, a novel carboxylated polyacrylonitrile nanofibrous membrane (C-PAN NFM) is designed and fabricated massively for the first time by adopting synchronously biaxial stretching and carboxylation. The C-PAN NFM is composed of the layered stack structure by cross-linked nanofibers. Due to its high specific surface area, excellent hydrophilicity, a large amount of carboxyl and amine groups, C-PAN NFM owns high fluoride adsorption capacity and outstanding selectivity. Both the carboxylation and acid treatment of C-PAN NFM improved the fluoride adsorption capacity remarkably. Specifically, C-PAN NFM shows excellent reusability without secondary pollution. The fluoride adsorption behavior of C-PAN NFM is dominated by chemical adsorption, and the adsorption mechanism is mainly driven by hydrogen bonding and ion exchange. The mass-produced C-PAN NFM is a novel polyacrylonitrile-based porous membrane that shows a great application potential for fluoride removal with good efficiency and recyclability.

Iron Oxide (Fe3O4)-Supported SiO2 Magnetic Nanocomposites for Efficient Adsorption of Fluoride from Drinking Water: Synthesis, Characterization, and Adsorption Isotherm Analysis

This research work reports the magnetic adsorption of fluoride from drinking water through silica-coated Fe3O4 nanoparticles. Chemical precipitation and wet impregnation methods were employed to synthesize the magnetic nanomaterials. Moreover, the synthesized nanomaterials were characterized for physicochemical properties through scanning electron microscopy, Fourier-transform infrared spectroscopy, and X-ray powder diffraction. Screening studies were conducted to select the best iron oxide loading (0.0–1.5 wt%) and calcination temperature (300–500 °C). The best selected nanomaterial (0.5Fe-Si-500) showed a homogenous FeO distribution with a 23.79 nm crystallite size. Moreover, the optimized reaction parameters were: 10 min of contact time, 0.03 g L−1 adsorbent dose, and 10 mg L−1 fluoride (F−) concentration. Adsorption data were fitted to the Langmuir and Freundlich isotherm models. The Qm and KF (the maximum adsorption capacities) values were 5.5991 mg g−1 and 1.869 L g−1 respectively. Furthermore, accelerated adsorption with shorter contact times and high adsorption capacity at working pH was among the outcomes of this research work.

Experimental and modeling studies for adsorbing different species of fluoride using lanthanum-aluminum perovskite

We investigated the adsorption mechanisms for removing fluoride based on experimental and modeling studies. Lanthanum-aluminum perovskite was designed for treating wastewater contaminated by fluoride. A fluorine-species model was developed to calculate the concentrations of different species of fluorine: F^-, HF, HF₂^-. Multiple kinetic models were examined and the pseudo-second order model was found the best to fit the experimental data, implying fast-chemisorption. The thermodynamic data were fitted by the Langmuir model and Freundlich model at different temperatures, indicating heterogeneous adsorption at low temperature and homogeneous adsorption at high temperature. The La₂Al₄O₉ material had less influence from negative ions when adsorbing fluoride. The adsorption mechanisms were further studied using experiments and Density Functional Theory calculations. The adsorption experiments could be attributed to the lattice plane (1 2 1) and La, O, Al sites. More Al sites were required than La sites for the increase of fluoride concentration. By contrast, more La sites than Al sites were needed for increased pH.

Efficient antimony removal by self-assembled core-shell nanocomposite of Co3O4@rGO and the analysis of its adsorption mechanism

Co₃O₄@rGO were facilely prepared by template free self-assemble in this study. The morphology of Co₃O₄@rGO was actiniaria-like core-shell structural nanocomposites. The formation mechanism of Co₃O₄@rGO core-shell nanocomposite was discussed according to its significant time-dependent morphology evolution course. To evaluate the application potential of Co₃O₄@rGO, its adsorption performance toward highly toxic antimony ions were studied. The Co₃O₄@rGO nanocomposite exhibit high anti-interference ability and high adsorption ability. The maximum adsorption capacities towards Sb(III) and Sb(V) are 151.04 and 165.51 mg/g, respectively. River water samples containing antimony violating the limit were used to evaluate the practical application of Co₃O₄@rGO, and high performance was achieved. The EU and China limits for antimony in drinking water can be met by using mesoporous Co₃O₄@rGO treating the actual river water samples with original antimony concentration lower than 50 μg/L. Adsorption isotherm, adsorption kinetics, pH and co-existing ions effects were also studied in details. The results indicate that mesoporous Co₃O₄@rGO is an excellent adsorbent for antimony removal. Mesoporous Co₃O₄@rGO nanocomposite is a potential candidate for antimony removal from waste water.

One-pot synthesis of Cr(III)-incorporated Zr(IV) oxide for fluoride remediation: a lab to field performance evaluation study

A low-cost Cr(III)-incorporated Zr(IV) bimetallic oxide (CZ) was synthesized by simple chemical precipitation method for removal of fluoride from contaminated water. The physicochemical properties of CZ before and after fluoride removal were established with several instrumental techniques such as TEM with elemental mapping, SEM with EDX, XRD, IR, XPS, zeta potential measurement, etc. Batch adsorption technique were carried out to understand the factors affecting fluoride adsorption, such as effects of initial pH, adsorbent dose, co-occurring ions, contact time, and temperature. The maximum adsorption capacity observed at pH between 5 and 7. The fluoride adsorption processes on CZ obeyed the pseudo-second-order rate equations and both Freundlich and DR isotherm models. The maximum adsorption capacity of 90.67 mg g^-1 was obtained. The thermodynamic parameters ΔH⁰ (positive), ΔS⁰ (positive), and ΔG⁰ (negative) indicating the fluoride sorption system was endothermic, spontaneous, and feasible. The CZ also successfully used as fluoride adsorbent for real field contaminated water collected from the Machatora district, Bankura, West Bengal, India. Graphical abstract Schematic representation of CZ synthesis and its application for lab as well as field water purification purpose.

Optimization of Boron Doped TiO2 as an Efficient Visible Light-Driven Photocatalyst for Organic Dye Degradation With High Reusability

No visible light activity is the bottle neck for wide application of TiO₂, and Boron doping is one of the effective way to broaden the adsorption edge of TiO₂. In this study, several Boron doped TiO₂ materials were prepared via a facile co-precipitation and calcination process. The B doping amounts were optimized by the degradation of rhodamine B (Rh B) under visible light irradiation, which indicated that when the mass fraction of boron is 6% (denoted as 6B-TiO₂), the boron doped TiO₂ materials exhibited the highest activity. In order to investigate the enhanced mechanism, the difference between B-doped TiO₂ and bare TiO₂ including visible light harvesting abilities, separation efficiencies of photo-generated electron-hole pairs, photo-induced electrons generation abilities, photo-induced charges transferring speed were studied and compared in details. h⁺ and ^·O2- were determined to be the two main responsible active species in the photocatalytic oxidation process. Besides the high degradation efficiency, 6B-TiO₂ also exhibited high reusability in the photocatalysis, which could be reused at least 5 cycles with almost no active reduction. The results indicate that 6B-TiO₂ has high photocatalytic degradation ability toward organic dye of rhodamine B under visible light irradiation, which is a highly potential photocatalyst to cope with organic pollution.

Biomaterial functionalized cerium nanocomposite for removal of fluoride using central composite design optimization study

Excess fluoride concentration in drinking water is a global issue, as this has an adverse effect on human health. Several adsorbents have been synthesized from natural raw material to remove fluoride from water. Reported adsorbents have some problems with the leaching of metal ions, fewer adsorption sites, and low adsorption capacity. Therefore, to address this, an effective biomaterial derived from the Luffa cylindrica (LC), containing many active sites, was integrated with a nano form of cerium oxide to form a robust, biocompatible, highly porous, and reusable LC-Ce adsorbent. This synthesized biosorbent offers better interaction between the active sites of LC-Ce and fluoride, resulting in higher adsorption capacity. Several factors, influence the adsorption process, were studied by a central composite design (CCD) model of statistical analysis. Langmuir's and Freundlich's models well describe the adsorption and kinetics governed by the pseudo-second-order model. The maximum monolayer adsorption capacity was found to be 212 and 52.63 mg/g for LC-Ce and LC, respectively determined by the Langmuir model. Detailed XPS and FTIR analyses revealed the underlying mechanism of fluoride adsorption via ion-exchange, electrostatic interaction, H-bonding, and ion-pair formation. All the results indicate that LC-Ce could serve as a suitable adsorbent for efficient fluoride removal (80-85%).

Synthesis of (ZrO2-Al2O3)/GO nanocomposite by sonochemical method and the mechanism analysis of its high defluoridation

A nanocomposite of (ZrO₂-Al₂O₃)/GO was successfully synthesized by a simple sonochemical method in this study. A special 3D network was formed in (ZrO₂-Al₂O₃)/GO, which produced a large surface area and good distribution of metal oxide nanoparticles. The as-synthesized (ZrO₂-Al₂O₃)/GO exhibits a maximum fluoride adsorption capacity of 62.2 mg/g, and an adsorption ability of 13.80 mg/g when the F^- equilibrium concentration is 1 mg/L, both of which are higher than most previously reported defluoridation adsorbents, indicating that it is among the top adsorbents. Large amounts of drinking water contaminated by F^- can be treated by (ZrO₂-Al₂O₃)/GO to meet the WHO limit, indicating the high potential for practical application of the adsorbent. Based on the experimental analysis, the origin of the high defluoridation performance and the adsorption mechanism were discussed in detail. Due to the simple preparation, easy operation and high performance, the adsorbent and the related sonochemical method are considered to be significant for developing highly effective adsorbents.