Application of two anaerobic membrane bioreactors with different pore size membranes for municipal wastewater treatment

Propidium monoazide - polymerase chain reaction reveals viable microbial community shifts in anaerobic membrane bioreactors treating domestic sewage at low temperature

An anaerobic membrane bioreactor (AnMBR) treated domestic sewage at 15 °C under different hydraulic retention time (HRT) conditions (6, 12, 16, and 24 h). Propidium monoazide (PMA)-PCR excluded microorganisms without intact cell membranes, focusing on the viable microbial community in anaerobic digestion. The results showed that the 6-hour HRT had poor treatment performance: low chemical oxygen demand removal efficiency (below 80%) and high mean trans-membrane pressure and flux (15 kPa and 9.4 L/(m2 h)). Comparatively, PMA-PCR combined with next-generation sequencing improved the identification of microbial changes compared to conventional 16S rRNA gene sequencing. HRT influenced microorganisms in the hydrolysis and acid-production stages, including carbohydrate-degrading bacteria such as Bifidobacterium and Prevotella 1. Remarkably, a comparison with an AnMBR at 25 °C showed Proteobacteria to be the main cause of membrane fouling in the low-temperature AnMBR, with most operational taxonomic units negatively correlated with HRT and solids retention time.

A Review on Opportunities and Limitations of Membrane Bioreactor Configuration in Biofuel Production

Biofuels are a clean and renewable source of energy that has gained more attention in recent years; however, high energy input and processing cost during the production and recovery process restricted its progress. Membrane technology offers a range of energy-saving separation for product recovery and purification in biorefining along with biofuel production processes. Membrane separation techniques in combination with different biological processes increase cell concentration in the bioreactor, reduce product inhibition, decrease chemical consumption, reduce energy requirements, and further increase product concentration and productivity. Certain membrane bioreactors have evolved with the ability to deal with different biological production and separation processes to make them cost-effective, but there are certain limitations. The present review describes the advantages and limitations of membrane bioreactors to produce different biofuels with the ability to simplify upstream and downstream processes in terms of sustainability and economics.

Achieving tetracycline removal enhancement with granules in marine matrices: Performance, adaptation, and mechanism studies

Using the aerobic granular sludge (AGS) to improve tetracycline (TET) removal in the treatment of mariculture wastewater was investigated in the present study. The AGS rapidly adapted to and was sustained in seawater matrices with a robust granule strength (k = 0.0014) and a more stable sludge yield than the activated sludge (AS) (0.14 vs 0.11 g-VSS/g-COD_rem). The compact structure provided the AGS with an anoxic environment, which favored the growth of N (37.3 %) and P removal bacteria (30.4 %) and the expression of functional genes (nos, nor, and nar), resulting in more than 62 % TN and TP removals, respectively. Similar abundances of aromatic compound-degrading bacteria (∼34 %) in both reactors (AGS and AS) led to comparable TET biodegradation efficiencies (∼0.045 mg/g-VSS). The greater size and surface area of the AGS expanded the boundary layer diffusion region, leading to 16 % increases in the granule's TET adsorption capacity.

Performance evaluation and energy potential analysis of anaerobic membrane bioreactor (AnMBR) in the treatment of simulated milk wastewater

An anaerobic membrane bioreactor (AnMBR) was employed as primary treatment unit for anaerobic treatment of simulated wastewater to produce high effluent quality. A lab scale hollow fiber membrane was used to scrutinize the performance of AnMBR as a potential treatment system for simulated milk wastewater and analyze its energy recovery potential. The 15 L bioreactor was operated continuously at mesophilic conditions (35 °C) with a pH constant of 7.0. The membrane flux was in the range of 9.6-12.6 L/m². h. The different organic loading rates (OLRs) of 1.61, 3.28, 5.01, and 8.38 g-COD/L/d, of simulated milk wastewater, were fed to the reactor and the biogas production rate was analyzed, respectively. The results revealed that the COD removal efficiencies of 99.54 ± 0.001% were achieved at the OLR of 5.01 gCOD/L/d. The highest methane yield was found to be at OLR of 1.61 gCOD/L/d at HRT of 30 d with the value of 0.33 ± 0.01 L-CH₄/gCOD. Moreover, based on the analysis of energy balance in the AnMBR system, it was found that energy is positive at all the given HRTs. The net energy production (NEP) ranged from 2.594 to 3.268 kJ/gCOD, with a maximum NEP value of 3.268 kJ/gCOD at HRT 10 d HRT. Bioenergy recovery with the maximum energy ratio, of 4.237, was achieved with an HRT of 5 d. The study suggests a sizable energy saving with the anaerobic membrane process.

Performance of Anaerobic Membrane Bioreactor (AnMBR) with Sugarcane Bagasse Ash-based Ceramic Membrane treating Simulated Low-strength Municipal Wastewater: Effect of Operation Conditions

This study assesses the performance of waste sugarcane bagasse ash (SBA)-based ceramic membrane in anaerobic membrane bioreactor (AnMBR) treating low-strength wastewater. The AnMBR was operated in sequential batch reactor (SBR) mode at hydraulic retention time (HRT) of 24 h, 18 h, and 10 h to understand the effect on organics removal and membrane performance. Feast-famine conditions were also examined to evaluate system performance under variable influent loadings. An average removal of >90% chemical oxygen demand (COD) was obtained at each HRT and starvation periods up to 96 days did not significantly affect removal efficiency. However, feast-famine conditions affected extracellular polymeric substances (EPS) production and consequently the membrane fouling. EPS production was high (135 mg/g MLVSS) when the system was restarted at 18 h HRT after shutdown (96 days) with corresponding high transmembrane pressure (TMP) build-up; however, the EPS content stabilized at ~60-80 mg/g MLVSS after a week of operation. Similar phenomenon of high EPS and high TMP was experienced after other shutdowns (94 and 48 days) as well. Permeate flux was 8.8±0.3, 11.2±0.1 and 18.4±3.4 L/m² h at 24 h, 18 h and 10 h HRT, respectively. Filtration-relaxation (4 min - 1 min) and backflush (up to 4 times operating flux) helped control fouling rate. Surface deposits (that significantly attributed to fouling) could be effectively removed by physical cleaning, resulting in nearly complete flux recovery. Overall, SBR-AnMBR system equipped with waste-based ceramic membrane appears promising for treatment of low-strength wastewater with disruptions in feeding.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s11270-023-06173-3.

Material mass balance and elemental flow analysis in a submerged anaerobic membrane bioreactor for municipal wastewater treatment towards low-carbon operation and resource recovery

The anaerobic membrane bioreactor (AnMBR) has gained huge attention as a municipal wastewater (MWW) treatment process that combined high organics removal, a low sludge yield and bioenergy recovery. In this study, a 20 L AnMBR was set up and operated steadily for 70 days in temperate conditions with an HRT of 6 h and a flux of 12 LMH for the treatment of real MWW, focusing on the behavior of the major elements (C, N, P and S) from an elemental balance perspective. The results showed that the AnMBR achieved more than 85 % COD removal, a low sludge yield (0.081 gVSS/gCOD_removed) and high methane production (0.31 L-CH₄/gCOD_removed) close to the theoretical value. The elemental flow analysis revealed that the AnMBR converted 77 % of the influent COD to methane (57 % gaseous and 20 % dissolved) and 6 % of the COD for sludge production. In addition, the AnMBR converted 34 % of the total carbon to energy-generated carbon, and only 3 % was in the form of CO₂ in the biogas for further upgradation, which was in line with the concept of carbon neutrality. Since little nitrogen or phosphorus were removed, the permeate was nutrient-rich and further treatment to recover the nutrients would be required. This study illustrates the superior performance of the AnMBR for MWW treatment with a microscopic view of elemental behavior and provides a reference for implementing the mainstream AnMBR process in carbon-neutral wastewater treatment plants.

Process characteristics and energy self-sufficient operation of a low-fouling anaerobic dynamic membrane bioreactor for up-concentrated municipal wastewater treatment

Up-concentration of municipal wastewater using physico-chemical methods can effectively enrich organic matter, facilitating subsequent anaerobic digestion of up-concentrated wastewater for enhanced methanogenesis at reduced energy consumption. An anaerobic dynamic membrane bioreactor (AnDMBR) assisted with biogas-sparging was developed to treat up-concentrated municipal wastewater, focusing on the effects of operating temperature and hydraulic retention time (HRT) as well as COD mass balance and energy balance. The COD removal stabilized at about 98 % over the experimental period, while gaseous and dissolved methane contributed 43-49 % and 2-3 % to the influent COD reducing greenhouse gas emissions. The formed dynamic membrane exists mainly as a heterogeneous cake layer with a uneven distribution feature, ensuring the stable effluent quality. Without adopting any physico-chemical cleaning, the transmembrane pressure (TMP) maintained at a low range (2.7 to 14.67 kPa) with the average TMP increasing rate of 0.089 kPa/d showing a long-term low-fouling operation. Increasing the concentration ratio, the methane production rate decreased from 0.18 to 0.15 L CH₄/gCOD likely due to the accumulation of particulate organics. Microbial community analysis indicated the predominant methanogenic pathway shifted from hydrogenotrophic to acetoclastic methanogenesis in response to the temperature change. Net energy balance (0.003-0.600 kWh/m³) can be achieved only under room temperature (25 °C) rather than mesophilic conditions (36 °C).

Energy-Efficient AnMBRs Technology for Treatment of Wastewaters: A Review

In recent years, anaerobic membrane bioreactor (AnMBRs) technology, a combination of a biological reactor and a selective membrane process, has received increasing attention from both industrialists and researchers. Undoubtedly, this is due to the fact that AnMBRs demonstrate several unique advantages. Firstly, this paper addresses fundamentals of the AnMBRs technology and subsequently provides an overview of the current state-of-the art in the municipal and domestic wastewaters treatment by AnMBRs. Since the operating conditions play a key role in further AnMBRs development, the impact of temperature and hydraulic retention time (HRT) on the AnMBRs performance in terms of organic matters removal is presented in detail. Although membrane technologies for wastewaters treatment are known as costly in operation, it was clearly demonstrated that the energy demand of AnMBRs may be lower than that of typical wastewater treatment plants (WWTPs). Moreover, it was indicated that AnMBRs have the potential to be a net energy producer. Consequently, this work builds on a growing body of evidence linking wastewaters treatment with the energy-efficient AnMBRs technology. Finally, the challenges and perspectives related to the full-scale implementation of AnMBRs are highlighted.

Pilot plant demonstration of temperature impacts on the methanogenic performance and membrane fouling control of the anaerobic membrane bioreactor in treating real municipal wastewater

A 5,000-L anaerobic membrane bioreactor (AnMBR) fed with actual municipal wastewater was employed to study the impact of temperature drops on methanogenic performance and membrane fouling. With temperature dropped from 25 °C to 15 °C, the methane yield decreased from 0.244 to 0.205 NL-CH₄/g-COD_removal and the dissolved methane increased from 29% to 43%, resulted in the methanogenic performance reduced by 25%. The membrane rejection offset the deteriorated anaerobic digestion at low temperatures and ensured the stable COD removal efficiency of 84.5%-90.0%. The synergistic effects of the increased microbial products and viscosity and the residual inorganic foulants aggravated the membrane fouling at lower temperatures. As the organic fouling was easily removed by NaClO, the inorganics related to the elements of S, Ca and Fe were the stubborn membrane foulants and required the enhanced acid membrane cleaning. These findings obtained under the quasi-practical condition are expected to promote the practical applications of mainstream AnMBR.

Effects of pharmaceuticals compounds and calcium on granulation, microbiology, and performance of anaerobic granular sludge systems

Granular sludge is a promising biotechnology to treat sewage contaminated with pharmaceuticals due to its increased toxicity resistance. In this context, this study evaluated the potential of Ca²⁺ as a granulation precursor and how pharmaceutical compounds (loratadine, prednisone, fluconazole, fenofibrate, betamethasone, 17α-ethinyl estradiol, and ketoprofen) affect granulation. Continuous and intermittent dosages of Ca²⁺ in the presence and absence of pharmaceuticals were evaluated. The results showed that intermittent addition of Ca²⁺ reduces the time for anaerobic sludge granulation, and pharmaceuticals presence did not impair granulation. 10% of the granules presented mean diameters greater than 2.11 mm within 93 days with intermittent Ca²⁺ dosage in the pharmaceuticals' presence. In contrast, no granules higher than 2.0 mm were observed with no precursor addition. The pharmaceuticals' toxicity may have created a stress condition for the microbial community, contributing to more EPS production and a greater potential for granulation. It was also verified that pharmaceuticals' presence did not decrease organic matter, total alkalinity, and volatile fatty acids removals. The 16S rRNA gene analysis revealed taxa resistance to recalcitrant compounds when pharmaceuticals were added. Besides, the efficiency of a granular sludge bioreactor (EGSB) was evaluated for pharmaceuticals removal, and betamethasone, fenofibrate, and prednisone were effectively removed.

A semi-industrial scale AnMBR for municipal wastewater treatment at ambient temperature: performance of the biological process

A semi-industrial scale AnMBR plant was operated for more than 600 days to evaluate the long-term operation of this technology at ambient temperature (ranging from 10 to 27 ^○C), variable hydraulic retention times (HRT) (from 25 to 41 h) and influent loads (mostly between 15 and 45 kg COD·d^-1). The plant was fed with sulfate-rich high-loaded municipal wastewater from the pre-treatment of a full-scale WWTP. The results showed promising AnMBR performance as the core technology for wastewater treatment, obtaining an average 87.2 ± 6.1 % COD removal during long-term operation, with 40 % of the data over 90%. Five periods were considered to evaluate the effect of HRT, influent characteristics, COD/SO₄^2--S ratio and temperature on the biological process. In the selected periods, methane yields varied from 70.2±36.0 to 169.0±95.1 STP L CH₄·kg^-1 COD_inf, depending on the influent sulfate concentration, and wasting sludge production was reduced by between 8 % and 42 % compared to conventional activated sludge systems. The effluent exhibited a significant nutrient recovery potential. Temperature, HRT, SRT and influent COD/SO₄^2--S ratio were corroborated as crucial parameters to consider in maximizing AnMBR performance.

Sodium hypochlorite induced inhibition in anaerobic digestion and possible approach to maintain methane fermentation performance

Since sodium hypochlorite (NaClO), a commonly used chemical to deal with membrane fouling, is toxic to microorganisms, it is a major concern in the membrane cleaning process. In this study, the concentration-dependent effects of NaClO (0-9 g/L) on the biodegradation performance and microbial activity were investigated via batch experiments. The methane production (obtained approximately 140 mL) and microbial community revealed by principal coordinates analysis were almost unaffected when the NaClO concentration ranged between 0 and 3 g/L. A follow-up batch experiment was conducted and revealed that the microbial products could help protect or recover the activity of anaerobic microorganisms at a high NaClO concentration of 10 g/L. Additionally, correlation analysis was used to investigate the associations between the 15 major bacterial genera. Moreover, the microbial analysis results indicated that the top 10 operational taxonomic units most affected by NaClO were primarily coryneform and filamentous bacteria.

Application of deep learning for predicting the treatment performance of real municipal wastewater based on one-year operation of two anaerobic membrane bioreactors

In this study, data-driven deep learning methods were applied in order to model and predict the treatment of real municipal wastewater using anaerobic membrane bioreactors (AnMBRs). Based on the one-year operating data of two AnMBRs, six parameters related to the experimental conditions (temperature of reactor, temperature of environment, temperature of influent, influent pH, influent COD, and flux) and eight parameters for wastewater treatment evaluation (effluent pH, effluent COD, COD removal efficiency, biogas composition (CH₄, N₂, and CO₂), biogas production rate, and oxidation-reduction potential) were selected to establish the data sets. Three deep learning network structures were proposed to analyze and reproduce the relationship between the input parameters and output evaluation parameters. The statistical analysis showed that deep learning closely agrees with the AnMBR experimental results. The prediction accuracy rate of the proposed densely connected convolutional network (DenseNet) can reach up to 97.44%, and the single calculation time can be reduced to within 1 s, suggesting the high performance of AnMBR treatment prediction with deep learning methods.

Microbial characteristics in anaerobic membrane bioreactor treating domestic sewage: Effects of HRT and process performance

Two anaerobic membrane bioreactors (AnMBRs) equipped with different membrane pore size (0.4 or 0.05 µm) were operated at 25˚C and fed with domestic wastewater. The hydraulic retention time (HRT) of the reactors was shortened. The microbial communities of the two AnMBRs were investigated by 16S rRNA gene amplicon sequencing to see the effects of HRT. The predominant Archaea was an aceticlastic methanogen Methanosaeta. The composition of hydrogenotrophic methanogens changed with the HRTs: the population of Methanobacterium was higher for longer HRTs, whereas the population of unclassified Methanoregulaceae was higher for shorter HRTs. The Anaerolineae, Bacteroidia and Clostridia bacteria were dominant in both of the reactors, with a combined relative abundance of over 55%. The relative abundance of Anaerolineae was proportional to the biogas production performance. The change in the population of hydrogenotrophic methanogens or Anaerolineae can be used as an indicator for process monitoring. The sum of the relative abundance of Anaerolineae and Clostridia fluctuated slightly with changes in the HRT in both AnMBRs when the reactor was stably operated. The co-occurrence analysis revealed the relative abundance of the operational taxonomic units belonging to Anaerolineae and Clostridia was functionally equivalent during the treatment of real domestic sewage. A principal coordination analysis revealed that the changes in the microbial community in each reactor were consistent with the change of HRT. In addition, both the HRT and the stability of the process are important factors for maintaining microbial community structures.

Anaerobic Membrane Bioreactors for Municipal Wastewater Treatment: A Literature Review

Currently, there is growing scientific interest in the development of more economic, efficient and environmentally friendly municipal wastewater treatment technologies. Laboratory and pilot-scale surveys have revealed that the anaerobic membrane bioreactor (AnMBR) is a promising alternative for municipal wastewater treatment. Anaerobic membrane bioreactor technology combines the advantages of anaerobic processes and membrane technology. Membranes retain colloidal and suspended solids and provide complete solid–liquid separation. The slow-growing anaerobic microorganisms in the bioreactor degrade the soluble organic matter, producing biogas. The low amount of produced sludge and the production of biogas makes AnMBRs favorable over conventional biological treatment technologies. However, the AnMBR is not yet fully mature and challenging issues remain. This work focuses on fundamental aspects of AnMBRs in the treatment of municipal wastewater. The important parameters for AnMBR operation, such as pH, temperature, alkalinity, volatile fatty acids, organic loading rate, hydraulic retention time and solids retention time, are discussed. Moreover, through a comprehensive literature survey of recent applications from 2009 to 2021, the current state of AnMBR technology is assessed and its limitations are highlighted. Finally, the need for further laboratory, pilot- and full-scale research is addressed.

Chemical oxygen demand and nitrogen transformation in a large pilot-scale plant with a combined submerged anaerobic membrane bioreactor and one-stage partial nitritation-anammox for treating mainstream wastewater at 25 °C

A novel municipal wastewater treatment process towards energy neutrality and reduced carbon emissions was established by combining a submerged anaerobic membrane bioreactor (SAnMBR) with a one-stage partial nitritation-anammox (PN/A), and was demonstrated at pilot-scale at 25 °C. The overall COD and BOD₅ removal efficiencies were 95.1% and 96.4%, respectively, with 20.3 mg L^-1 COD and 5.2 mg L^-1 BOD₅ remaining in the final effluent. The total nitrogen (TN) removal efficiency was 81.7%, resulting 7.3 mg L^-1 TN was discharged from the system. The biogas yield was 0.222 NL g^-1 COD _removed with a methane content range of 78-81%. Approximately 90% of influent COD was removed in the SAnMBR, and 70% of influent nitrogen was removed in the PN/A. The denitrification which occurred in the PN/A enhanced overall COD and nitrogen removal. The successful operation of this pilot-scale plant indicates the SAnMBR-PN/A process is suitable for treating real municipal wastewater.

Important effects of temperature on treating real municipal wastewater by a submerged anaerobic membrane bioreactor: Removal efficiency, biogas, and microbial community

A submerged anaerobic membrane bioreactor (SAnMBR) was used in the treatment of real municipal wastewater at operation temperatures ranging from 15 °C to 25 °C and hydraulic retention time (HRT) of 6 h. The treatment process was evaluated in terms of organic removal efficiency, biogas production, sludge growth and membrane filtration. During long-term operation, the SAnMBR achieved chemical oxygen demand removal efficiencies of about 90% with a low sludge yield (0.12-0.19 g-VSS/g-COD_rem) at 20-25 °C. Approximately 1.82-2.27 kWh/d of electric energy was generated during the wastewater treatment process at 20-25 °C, 0.67 kWh/d was generated at 15 °C. The microbial community analysis results showed that microbial community was dominated by aceticlastic methanogens, coupled by hydrogenotrophic methanogens and a very small quantity of methylotrophic methanogens. It was also shown that the stabilization of the microbial community could be attributed to the carbohydrate-protein degrading bacteria and the carbohydrate degrading bacteria.

One-year operation of a 20-L submerged anaerobic membrane bioreactor for real domestic wastewater treatment at room temperature: Pursuing the optimal HRT and sustainable flux

A 20 L hollow-fiber submerged anaerobic membrane bioreactor (SAnMBR) was used to treat real domestic wastewater at 25 °C with hydraulic retention times (HRTs) ranging from 4 to 12 h. The process performance was evaluated by organic removal efficiency, biogas production, sludge yield, and filtration behaviors during one-year's operation. For HRTs ranging between 6 and 12 h, the AnMBR showed good organic removal efficiency with chemical oxygen demand (COD) and biochemical oxygen demand (BOD) removal efficiencies of about 89% and 93%, respectively. The biogas yield was 0.26 L-gas/g-COD_fed, with approximately 80% methane content, and the sludge yield was 0.07-0.11 g-VSS/g-COD_rem. While at an HRT of 4 h, with the higher wastewater treatment capacity and organic loading rate (OLR), the biogas production was lower (0.17 L-gas/g-COD_fed), and the sludge production was higher (0.22 g-VSS/g-COD_rem). The organic removal performance (COD 84% and BOD 89%) at HRT of 4 h was acceptable due to the effective separation effect of the membrane filtration process. According to COD balance analysis, the low biogas yield and high sludge yield at HRT of 4 h were due to insufficient biodegradation under an OLR of 2.05 g-COD/L-reactor/d. Theoretical calculations based on Henry's law indicate that the ideal methane content in the biogas should be 82-85% when the operational temperature was 25 °C. To achieve a high flux and sustainable AnMBR operation, the impact of mixed liquor suspended solid (MLSS) and gas sparging velocity (GSV) on the filtration performance was analyzed. The critical flux increased with increase in the GSV from 24.2 to 174.3 m/h, but decreased with increase in the MLSS concentration from 8.2 to 20.2 g/L. Therefore, decreasing fouling rate to 0.8-1.2 kPa/d by efficiently controlling GSV and MLSS, sustainable operation could be achieved at a flux of 0.34 m/d.