Perchlorate adsorption onto epichlorohydrin crosslinked chitosan hydrogel beads

Acid-resistant chitosan/graphene oxide adsorbent for Cu2+ removal: The role of mixed cross-linking and amino-functionalized

Copper ions in wastewater pose a significant threat to human and ecological safety. Therefore, preparing macroscopic adsorbents with reusable and high adsorption performance is paramount. This paper used graphene oxide as the adsorbent and chitosan as the thickener. Additionally, a silane coupling agent was employed to enhance the acid resistance of chitosan, and amino-modification of graphene oxide was performed. Macroscopic adsorbents with high adsorption capacity were fabricated using 3D printing technology. The results show that all five proportions of inks exhibit good printability. Dissolution experiments revealed that all materials maintained structural integrity after 180 days across pH values. Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Photoelectron Spectroscopy (XPS) confirmed the successful preparation of the materials. Adsorption experiments showed that the best performing material ratio was 8 wt% graphene oxide and 7 wt% chitosan. Adsorption kinetics and isothermal adsorption experiments demonstrated that the adsorption process occurred via monolayer chemisorption. The adsorption process was attributed to strong electrostatic forces, van der Waals forces, and nitrogen/oxygen-containing functional group coordination. Cycling experiments showed that the material retained good adsorption performance after 6 cycles, suggesting its potential for practical heavy metal treatment applications.

Recent advances in chitosan-based nanocomposites for adsorption and removal of heavy metal ions

Due to the high concentration of various toxic and dangerous pollutants, industrial effluents have imposed increasing threats. Among the various processes for wastewater treatment, adsorption is widely used due to its simplicity, good treatment efficiency, availability of a wide range of adsorbents, and cost-effectiveness. Chitosan (CS) has received great attention as a pollutant adsorbent due to its low cost and many -OH and -NH2 functional groups that can bind heavy metal ions. However, weaknesses such as sensitivity to pH, low thermal stability and low mechanical strength, limit the application of CS in wastewater treatment. The modification of these functional groups can improve its performance via cross-linking and grafting agents. The porosity and specific surface area of CS in powder form are not ideal, so physical modification of CS via integration with other materials (e.g., metal oxide, zeolite, clay, etc.) leads to the creation of composite materials with improved absorption performance. This review provides reports on the application of CS and its nanocomposites (NCs) for the removal of various heavy metal ions. Synthesis strategy, adsorption mechanism and influencing factors on sorbents for heavy metals are discussed in detail.

Removal of low concentration of perchlorate from natural water by quaternized chitosan sphere (CGQS): Efficiency and mechanism research

In this study, an innovative approach utilizing betaine as a raw material was employed to effectively modify the surface of chitosan with quaternary ammonium groups. X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectrometer (FTIR) characterization showed that the quaternary ammonium groups on betaine were successfully loaded on the chitosan surface. The effects of dosage, pH, initial perchlorate concentration, temperature and co-existing anions on the removal efficiency of perchlorate were investigated. The saturated adsorption capacity of CGQS was 35.41 mg/g under natural condition. The impact of initial perchlorate concentrations and column flow rates on the column adsorption experiments were investigated, as well as natural water tests. Sterilizing performance experiments of CGQS were carried out innovatively. Under the condition of initial concentration of 0.5 mg/L, 9 BV/h (bed volume per hour), the effluent natural water was up to standard (≤0.07 mg/L) with a treatment capacity of 210 BV/g, and the sterilizing rate of CGQS was up to 97.02%. The proposed adsorption mechanisms involved surface pore adsorption, electrostatic adsorption of quaternary ammonium groups, and ion exchange between chloride and perchlorate ions. The CGQS prepared in this work had great potential for treating trace perchlorate contamination in natural water.

Chitosan-minerals-based composites for adsorption of caesium, cobalt and europium

Currently, there is a growing interest in the use of natural materials in various fields of science, technology and environmental protection due to their availability, low-cost, non-toxicity and biodegradability. Chitosan, natural clay of local origin, montmorillonite, zeolite, cross-linking agents (epichlorohydrin, sodium tripolyphosphate, glutaraldehyde) and plasticisers (glycerol) were used to synthesise composites. The composites were characterised by attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), X-ray diffraction analysis (XRD) and scanning electron microscope (SEM), tested for their antibacterial activity and used in batch experiments to study the adsorption of caesium, cobalt and europium ions. The maximum capacities for adsorption of caesium, cobalt and europium on the composites were 1400 mg/g, 900 mg/g and 18 mg/g, respectively. The experimental data fit better the Langmuir isotherm model and indicate favourable monolayer adsorption of Cs+, Co2+ and Eu3+ at homogeneous sites of the composites. The experimental data were in better agreement with the pseudo-second-order non-linear kinetic model for most elements and adsorbents. Adaptive neuro-fuzzy inference system proved to be a practical tool with good performance and generalisation capability for predicting the adsorption capacity of composites for caesium, cobalt, and europium ions. It was found that the predicted data were very close to the experimental data.

Cr(VI) and doxorubicin adsorptive capture by a novel bionanocomposite of Ti-MOF@TiO2 incorporated with watermelon biochar and chitosan hydrogel

Biodegradable polymers, biochars and metal organic frameworks (MOFs) have manifested as top prospects for elimination of harmful pollutants. In the current study, Ti-MOF was synthesized and decorated with TiO2 nanoparticles, then embedded into watermelon peel biochar and functionalized with chitosan hydrogel to produce Ti-MOF@TiO2@WMPB@CTH. Various instruments were employed to assure the effective production of the bionanocomposite. The HR-TEM and SEM studies referred to excellent surface porosity and homogeneity of Ti-MOF@TiO2@WMPB@CTH bionanocomposite, with 51.02-74.23 nm. Based on the BET analysis, the mesoporous structure has a significant surface area of 366.04 m2 g-1 and a considerable total pore volume of 11.38 × 10-2 cm3 g-1, with a mean pore size of 12.434 nm. Removal of doxorubicin (DOX) and hexavalent chromium (Cr(VI)) was examined under various experimentations. Pseudo-second order kinetic models in addition to Langmuir isotherm offered the best fitting. Thermodynamic experiments of the two contaminants demonstrated spontaneous and endothermic interactions. After five subsequent adsorption and desorption cycles, Ti-MOF@TiO2@WMPB@CTH bionanocomposite demonstrated an exceptional recyclability for the elimination of DOX and Cr(VI) ions, reaching 97.96 % and 95.28 %, respectively. Finally, the newly designed Ti-MOF@TiO2@WMPB@CTH bionanocomposite demonstrated a high removing efficiency of Cr(VI) ions and DOX from samples of real water.

Recent advances in removal of inorganic anions from water by chitosan-based composites: A comprehensive review

Chitosan is a modified natural carbohydrate polymer that has been found in the exoskeletons of crustaceans (e.g., lobsters, shrimps, krill, barnacles, crayfish, etc.), mollusks (octopus, oysters, squids, snails), algae (diatoms, brown algae, green algae), insects (silkworms, beetles, scorpions), and the cell walls of fungi (such as Ascomycetes, Basidiomycetes, and Phycomycetes; for example, Aspergillus niger and Penicillium notatum). However, it is mostly acquired from marine crustaceans such as shrimp shells. Chitosan-based composites often present superior chemical, physical, and mechanical properties compared to single chitosan by incorporating the benefits of both counterparts in the nanocomposites. The tunable surface chemistry, abundant surface-active sites, facilitation synthesize and functionalization, good recyclability, and economic viability make the chitosan-based materials potential adsorbents for effective and fast removal of a broad range of inorganic anions. This article reviews the different types of inorganic anions and their effects on the environment and human health. The development of the chitosan-based composites synthesis, the various parameters like initial concentration, pH, adsorbent dosage, temperature, the mechanism of adsorption, and regeneration of adsorbents are discussed in detail. Finally, the prospects and technical challenges are emphasized to improve the performance of chitosan-based composites in actual applications on a pilot or industrial scale.

Experimental and theoretical studies on nitrate removal using epichlorohydrin-modified cross-linked chitosan derived from shrimp waste

Nitrates level in water is a worldwide problem that represents a risk to the environment and people's health; efforts are currently devoted to the development and implementation of new biomaterials for their removal. In this study, chitosan (Ch) from shrimp waste and the related epichlorohydrin-modified crossover chitosan (Ch-EPI) were used to remove nitrates from aqueous solutions. The mechanism of selective nitrate removal was elucidated and validated by theoretical calculations. The physicochemical performance of Ch and Ch-EPI was investigated through the main parameters pH, adsorption capacity, contact time, initial nitrate concentration, coexisting anions, and temperature. The experimental data were fitted to widely used adsorption kinetic models and adsorption isotherms. The maximum percentage of nitrate adsorption was reached at an equilibrium pH of 4.0 at an adsorbent dose of 2.0 g/L after a contact time of 50 min. Competing anion experiments show that chloride and sulfate ions have minimal and maximal effects on nitrate adsorption by Ch-EPI. Experimental adsorption data are best fitted to pseudo-second-order kinetic and isothermal Langmuir models. The maximum adsorption capacities of Ch and Ch-EPI for nitrate removal were 12.0 mg/g and 38 mg/g, respectively.

Crosslinked modified chitosan biopolymer for enhanced removal of toxic Cr(VI) from aqueous solution

Two new crosslinked modified chitosan biopolymers, namely (CTS-VAN) and (Fe₃O₄@CTS-VAN) bioadsorbents were prepared starting from chitosan and 4-hydroxy-3-methoxybenzaldehyde (VAN) in presence of epichlorohydrin. The analytical techniques FT-IR, EDS, XRD, SEM and XPS besides BET surface analysis were utilized for full characterization of the bioadsorbents. Batch experiments were conducted to study the effect of various influencing parameters in Cr (VI) removal such as initial pH, contact time, adsorbent amount and initial Cr (VI) concentration. The adsorption of Cr (VI) was found out to be maximum at pH = 3 for both bioadsorbents. Langmuir isotherm fit well the adsorption process with a maximum adsorption capacity of 188.68 and 98.04 mg/g for CTS-VAN and Fe₃O₄@CTS-VAN, respectively. The adsorption process followed pseudo second-order kinetics with R² values of 1 and 0.9938 for CTS-VAN and Fe₃O₄@CTS-VAN, respectively. X-ray photoelectron spectroscopy (XPS) analysis showed that Cr(III) accounted for 83 % of the total Cr bound to bioadsorbents surface, which indicated reductive adsorption was responsible for Cr(VI) removal by the bioadsorbents. Cr(VI) was initially adsorbed on the positively charged surface of the bioadsorbents and reduced to Cr(III) by electrons provided by oxygen-comprising functional groups (e.g., CO), and consequently part of the converted Cr(III) stayed on the surface and the rest released into solution.

A comparative study on Fe(III)-chitosan and Fe(III)-chitosan-CTAB composites for As(V) removal from water: preparation, characterization and reaction mechanism

Fe(III)-chitosan and Fe(III)-chitosan-CTAB composites were prepared using an ionotropic gelation method. Various techniques were used to analyze the morphology, structure, and property of the adsorbents, including SEM, EDS, FT-IR, XPS, and zeta potential. Compared with Fe(III)-chitosan, Fe(III)-chitosan-CTAB was more effective for As(V) adsorption at a wide range of pH (3.0-8.0). The adsorption of As(V) onto Fe(III)-chitosan and Fe(III)-chitosan-CTAB could reach equilibrium in 20 min, and their maximum adsorption capacities were 33.85 and 31.69 mg g^‒1, respectively. The adsorption kinetics was best described by the pseudo-second-order model (R² = 0.998 and 0.992), whereas the adsorption isotherm was fitted well by the Freundlich model (R² = 0.963 and 0.987). The presence of H₂PO₄^- significantly inhibited the adsorption of As(V) onto Fe(III)-chitosan and Fe(III)-chitosan-CTAB, and humic acid also led to a slight decrease in As(V) adsorption by Fe(III)-chitosan-CTAB. Over 94% of As(V) at the initial concentration of no more than 5 mg L^-1 was removed from real water by the two adsorbents. 1% (w/v) NaOH solution was determined to be the most suitable desorption agent. Fe(III)-chitosan and Fe(III)-chitosan-CTAB still maintained their initial adsorption capacities after five adsorption-desorption cycles. Based on different characterization results, both electrostatic attraction and surface complexation mechanisms played important roles in As(V) adsorption on Fe(III)-chitosan and Fe(III)-chitosan-CTAB.

Calcium-modified granular attapulgite removed phosphorus from synthetic wastewater containing low-strength phosphorus

Traditional biological processes combined with chemical precipitation methods can effectively reduce phosphate concentration in wastewater. However, discharge standards required additional advanced treatment technologies, and the removal of low phosphorus concentration is complicated and expensive. This study proposes application of a simple and recyclable adsorbent to remove low-concentration phosphorus from water. The removal efficiency of phosphorus from low-strength synthetic wastewater was investigated and the adsorption mechanism was analyzed. When the initial phosphorus concentration was 2.0 mg/L, the phosphorus adsorption capacity of Ca-GAT increased to 0.891 mg/g from 0.074 mg/g for GAT at 298 K and pH of 7. Phosphorus adsorption on Ca-GAT performs well when the solution pH is in the range of 5-10, and it is not conducive to the adsorption reaction when the solution pH exceeds 11. The competing anions (such as NO₃^-, SO₄^2-, HCO₃^- and F^-) existed, Ca-GAT still performed better in removing phosphorus. Then, the saturated absorbents could be effectively regenerated with a 0.5 mos/L NaOH solution, while desorption efficiency was reduced from 97.11% to 33.06% after fifth regeneration cycle. Finally, Scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS) analysis demonstrated that the Ca²⁺ content on the Ca-GAT surface played an important role in capturing phosphate ions from wastewater. Phosphorus was mainly removed via the formation of Ca-phosphorus precipitation. To some extent, ligand exchanges of CO₃^2- and OH- with HPO₄^2- and H₂PO₄^- were also beneficial for phosphorus removal. The present work shows that attapulgite has sustainable and beneficial potential in the removal of low-strength phosphorous in wastewater, and the phosphorus loaded adsorbent can be used in the agriculture as slow-release fertilizer.

Study on a Hydrogel for Adsorption of Chloride Ions in Cementitious Materials

Chloride ions in the seaside environment can corrode the steel reinforcement in concrete, which greatly endangers the safety of seaside structures. As an excellent adsorption material, hydrogel is widely used in the field of water treatment but is rarely used in cementitious materials. In this study, a polyacrylamide–chitosan hydrogel (PAMC) was prepared with N,N-methylenebisacrylamide as the cross-linking agent and acrylamide as the monomer. The prepared PAMC gel could effectively adsorb chloride ions in simulated seawater and simulated sea sand environments, and the maximum adsorption capacity of chloride ions by PAMC-1 (prepared from 2.5 g acrylamide and 1% content of N,N-methylenebisacrylamide relative to acrylamide) gels in simulated seawater was 55.53 mg/g. The adsorption behavior of the PAMC gels in solution fit the Langmuir isotherm model. The composition and morphology of the PAMC gel were characterized, and the responsiveness of the PAMC gel to the environment was studied. The results showed that the PAMC gels adsorbed better in alkaline environments and thus could be used in alkaline cement-based environments. The mortar sample containing the PAMC-1 gel had higher resistance to chloride ion penetration, and the chloride ion content at 7.5–10mm from the surface of the sample cured for 28 days was reduced by 41.4% compared to the samples without the gel.

Modification of Superabsorbent Hydrogels for Industrial Wastewater Treatment

A breakthrough in superabsorbent hydrogel (SAH) preparation was studied in the current issue by blending potato starch and acrylic acid for wastewater treatment. Gamma irradiation source (60Co irradiation) was used to irradiate SAH from 1 to 10 kGy dose at room temperature (~27°C). The swelling ratio, water absorption, equilibrium water content, and gel fraction properties of the hydrogel were investigated. The as-prepared hydrogel treated with KOH (THG) showed excellent absorption capacity but less mechanical stability compared to untreated hydrogel (UHG). The gel fraction of treated SAH was slightly lower in methanol, but the utmost in water at 5 kGy infers the proper grafting of SAH at this point. The prepared SAH was characterized using scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) to investigate the surface morphology and molecular interaction, respectively. Moreover, this study’s focal point is to propose an alternative method to remove chromium and methylene blue by SAH from industrial wastewater. The Cr adsorption capacity of UHG was higher than that of THG because the proton’s replacement is easier than that of K by Cr. On the other hand, THG was found to be more efficient in removing methylene blue from industrial wastewater due to the presence of an easily ionized group (–COOK) in SAH. Therefore, the hydrogel can be proposed as a potential superabsorbent to remove heavy metals and organic dyes from industrial wastewater.

Fabrication of a CO2-responsive chitosan aerogel as an effective adsorbent for the adsorption and desorption of heavy metal ions

In the traditional desorption method, strong acid is commonly used as an eluent for the regeneration of adsorbents. It is of critical economic and environmental significance to develop a chemical-free desorption method. In this study, a new CO₂-responsive chitosan aerogel adsorbent was synthesized from CO₂-responsive poly(acrylic acid-2-(dimethylamino)ethyl methacrylate) and chitosan by physicochemical double crosslinking for the adsorption of Cu²⁺. Compared with the chitosan aerogel, the adsorption capacity of Cu²⁺ and mechanical properties of CO₂-responsive chitosan aerogel increased by 162% and 660%, respectively. Most importantly, after the adsorption of Cu²⁺ by CO₂-responsive chitosan aerogel, the Cu²⁺ could be desorbed by CO₂ bubbling, and the desorption rate of metal ions was more than 80%. The adsorption of Cu²⁺ by aerogel was attributed to chelation and complexation. The desorption of porous chitosan/P(AA-co-DMAEMA) aerogels (CPA) by CO₂ mainly occurred through charge repulsion of protonated ‒NH₂ and ‒N‒ groups. After 6 cycles, the adsorption capacity of CPA for metal ions still reached 70% of the initial adsorption capacity, and the desorption rate reached 75%. This novel CO₂-responsive chitosan aerogel is a highly efficient and environmentally friendly adsorbent for the adsorption and recovery of metal ions.

Advances in carbohydrate-based polymers for the design of suture materials: A review

Suture materials constitute one of the largest biomedical material groups with a huge global market of $ 1.3 billion annually and employment in over 12 million procedures per year. Suture materials have radically evolved over the years, from basic strips of linen to more advanced synthetic polymer sutures. Yet, the journey to the ideal suture material is far from over and we now stand on the brink of a new era of improved suture materials with greater safety and efficacy. This next step in the evolutionary timeline of suture materials, involves the use of natural, carbohydrate polymers that have, until recent years, never before been considered for suture material applications. This review exposes the latest and most important advancements in suture material development while digging deep into how natural, carbohydrate polymers can serve to advance this field.