Assessment of brominated flame retardants in a small mixed waste electronic and electrical equipment (WEEE) plastic recycling stream in the UK

Multi-sensor characterization for an improved identification of polymers in WEEE recycling

Polymers represent around 25% of total waste from electronic and electric equipment. Any successful recycling process must ensure that polymer-specific functionalities are preserved, to avoid downcycling. This requires a precise characterization of particle compounds moving at high speeds on conveyor belts in processing plants. We present an investigation using imaging and point measurement spectral sensors on 23 polymers including ABS, PS, PC, PE-types, PP, PVC, PET-types, PMMA, and PTFE to assess their potential to perform under the operational conditions found in recycling facilities. The techniques applied include hyperspectral imaging sensors (HSI) to map reflectance in the visible to near infrared (VNIR), short-wave (SWIR) and mid-wave infrared (MWIR) as well as point Raman, FTIR and spectroradiometer instruments. We show that none of the sensors alone can identify all the compounds while meeting the industry operational requirements. HSI sensors successfully acquired simultaneous spatial and spectral information for certain polymer types. HSI, particularly the range between (1600-1900) nm, is suitable for specific identification of transparent and light-coloured (non-black) PC, PE-types, PP, PVC and PET-types plastics; HSI in the MWIR is able to resolve specific spectral features for certain PE-types, including black HDPE, and light-coloured ABS. Fast-acquisition Raman spectroscopy (down to 500 ms) enabled the identification of all polymers regardless their composition and presence of black pigments, however, it exhibited limited capacities in mapping applications. We therefore suggest a combination of both imaging and point measurements in a sequential design for enhanced robustness on industrial polymer identification.

The Effects of Bromine Additives on the Recyclability of Injection Molded Electronic Waste Polymers

Excessive waste amounts, such as waste electrical and electronic equipment (WEEE) and plastic waste, have increased simultaneously with the development of society. Despite the increased material amounts, the recycling rates are too low and those have a great potential to contribute actions toward a circular economy. A certain restricted factor for recycling is the heterogenous nature of materials, such as WEEE-included additives. This study investigates the effects of a WEEE polymer including bromine on recycling ability, analyzing its physical and mechanical features. The study demonstrates that polymer sorting is profitable for WEEE polymers from the material qualitative perspective, because various processability and material features are achieved in the study between material categories, and especially unidentified polymers have the weakest features in the studied tests. The separation of bromine concentration is also recommended because bromine-free materials have more advanced features that can be confirmed by statistical analyses. The achieved results support the idea that novel circular economy actions have the potential for effective, efficient WEEE polymer recycling processes with technological innovations, especially when all variables (e.g., recycling cycles and process parameters) are observed and it enables an option to reduce the need for virgin plastic.

A large diversity of organohalogen contaminants reach the meso- and bathypelagic organisms in the Bay of Biscay (northeast Atlantic)

Deep-sea ecosystems play a key role in the cycling and vertical transfer of matter and energy in oceans. Although the contamination of deep-sea demersal and benthic organisms by persistent organic pollutants has been proven, deep pelagic species have been far less studied. To fill these gaps, we studied the occurrence of a large variety of hydrophobic organic contaminants including polychlorinated biphenyls (PCBs), organochlorine pesticides (OCPs), legacy and alternative brominated flame retardants (BFRs) and per- and polyfluoroalkyl substances (PFASs) in crustaceans and fish species collected in the Bay of Biscay, northeast Atlantic. The results highlighted the global predominance of PCBs in fish, followed by OCPs, PFASs and PBDEs, with highly variable concentrations among species. Most of the chlorinated or brominated contaminants showed increasing concentrations with increasing δ¹⁵N values, while most PFASs showed inverse trends. The contaminant profiles and diagnostic ratios revealed species-specific metabolic capacities and peculiar contribution of highly-brominated BFRs.

Decabromodiphenyl ethane induces locomotion neurotoxicity and potential Alzheimer's disease risks through intensifying amyloid-beta deposition by inhibiting transthyretin/transthyretin-like proteins

As a major alternative to traditional brominated flame retardants (BFRs), decabromodiphenyl ethane (DBDPE) is widely used and has been commonly detected in various environmental media and organisms. Few previous studies have focused on DBDPE-induced locomotion neurotoxicity, and the exact molecular mechanisms and related health risks remain unclear. In this study, we first analyzed the locomotion indicators of nematodes following DBDPE exposure, demonstrated that DBDPE caused locomotion neurotoxicity, and identified that a series of the transthyretin (TTR)-like genes participated in the regulation of nematode motility by transcriptomic analysis, gene transcription validation and TTR-like mutant verification. Subsequently, this study demonstrated that DBDPE exacerbated amyloid-beta (Aβ) deposition by repressing TTR/TTR-like gene transcription based on Alzheimer's disease (AD) model nematodes and human SH-SY5Y cells following DBDPE exposure and further revealed that DBDPE reduced the binding between TTR and Aβ by competing with the strand G region sites on the TTR/TTR-like protein, ultimately exacerbating Aβ deposition and the risk of AD. In short, our study demonstrated that DBDPE induced locomotion neurotoxicity and potential AD risks through intensifying Aβ deposition by inhibiting TTR/TTR-like proteins, providing reference support for risk management and policy formulation related to DBDPE and similarly structured novel BFRs.

Identification and occurrence of TBBPA and its debromination and O-methylation transformation products in sediment, fish and whelks from a typical e-waste dismantling site

Tetrabromobisphenol A (TBBPA) and its debromination (∑BBPA) and O-methylation (∑MeO-TBBPA) products were widely detected in matched sediments, fish, and whelks samples collected from a typical electronic waste (e-waste) dismantling site in Southern China, with concentrations ranging from 19.8 to 1.52 × 10⁴, 8.05 to 1.84 × 10³, and 0.08 to 11.9 ng/g dry weight in sediments, and 6.96 to 1.97 × 10⁵, 3.84 to 7.07 × 10³, and 3.42 to 472 ng/g lipid in biotas, for TBBPA, ∑BBPA, and ∑MeO-TBBPA, respectively. Significantly higher concentrations of these targets were found in samples collected close to the e-waste site, indicating their potential e-waste sources. Tri-BBPA was the most abundant debromination products in sediments, whereas diMeO-TBBPA was the dominant O-methylation product in biotas. Relatively higher levels of diMeO-TBBPA found in liver and kidneys, suggesting these chemicals might be mainly derived from the in vivo biotransformation. Furthermore, significantly higher biota-sediment accumulation factor values were found for diMeO-TBBPA than these of TBBPA, indicating that O-methylation would increases their accumulation in aquatic organisms. Our study provides insights into the accumulation and biotransformation of TBBPA in aquatic systems. Further studies should pay attention to the occurrence as well as potential health risks of these transformation products.

Recycling plastics containing decabromodiphenyl ether into new consumer products including children's toys purchased in Japan and seventeen other countries

Polybrominated diphenyl ethers (PBDEs) are flame retardants widely used to manufacture several commercial plastic products. The major homologue in commercial PBDE mixtures are listed in the Stockholm Convention on Persistent Organic Pollutants and are scheduled for global elimination. Hence, to understand more about unintentional contamination of plastic recycling stream by restricted PBDEs, we examined 540 small plastic consumer products (1139 components after dismantling), including children's toys, purchased in 18 countries (mainly Japan) between 2015 and 2019. Handheld X-ray fluorescence analysis revealed that 219 plastic components (19% of the total samples) contained bromine at a concentration of ≥30 mg kg^-1. Chemical analysis of these bromine-positive components revealed that 109 pieces (9.6% of the total), mainly those made of black-colored plastic, contained PBDEs at concentrations ranging between 35 and 10,000 mg kg^-1, with the maximum contribution from decabromodiphenyl ether (decaBDE). These PBDE concentrations were insufficient to impart flame retardancy, suggesting that the recycled plastic used to manufacture these consumer products probably originated from electronic waste, the manufacture of which was the primary use of commercial decaBDE mixtures. PBDEs were also found in secondary raw plastic materials and their final products obtained in India in 2019, demonstrating that plastics containing decaBDE end up in products where they serve no functional purpose. To contribute to the circular economy, the recycling of plastic waste in end-of-life products should be promoted. However, urgent action is needed to prevent plastic additives of concern, including PBDEs, from entering new products used in daily lives, particularly those used by children.

Recycling Plastics from WEEE: A Review of the Environmental and Human Health Challenges Associated with Brominated Flame Retardants

Waste electrical and electronic equipment (WEEE) presents the dual characteristic of containing both hazardous substances and valuable recoverable materials. Mainly found in WEEE plastics, brominated flame retardants (BFRs) are a component of particular interest. Several actions have been taken worldwide to regulate their use and disposal, however, in countries where no regulation is in place, the recovery of highly valuable materials has promoted the development of informal treatment facilities, with serious consequences for the environment and the health of the workers and communities involved. Hence, in this review we examine a wide spectrum of aspects related to WEEE plastic management. A search of legislation and the literature was made to determine the current legal framework by region/country. Additionally, we focused on identifying the most relevant methods of existing industrial processes for determining BFRs and their challenges. BFR occurrence and substitution by novel BFRs (NBFRs) was reviewed. An emphasis was given to review the health and environmental impacts associated with BFR/NBFR presence in waste, consumer products, and WEEE recycling facilities. Knowledge and research gaps of this topic were highlighted. Finally, the discussion on current trends and proposals to attend to this relevant issue were outlined.

Recycling Potential for Non-Valorized Plastic Fractions from Electrical and Electronic Waste

This paper describes a study for waste of electrical and electronic equipment (WEEE) to characterise the plastic composition of different mixed plastic fractions. Most of the samples studied are currently excluded from material recycling and arise as side streams in state-of-the-art plastics recycling plants. These samples contain brominated flame retardants (BFR) or other substances of concern listed as persistent organic pollutants or in the RoHS directive. Seventeen samples, including cathode ray tube (CRT) monitors, CRT televisions, flat screens such as liquid crystal displays, small domestic appliances, and information and communication technology, were investigated using density- and dissolution-based separation processes. The total bromine and chlorine contents of the samples were determined by X-ray fluorescence spectroscopy, indicating a substantial concentration of both elements in density fractions above 1.1 g/cm3, most significantly in specific solubility classes referring to ABS and PS. This was further supported by specific flame retardant analysis. It was shown that BFR levels of both polymers can be reduced to levels below 1000 ppm by dissolution and precipitation processes enabling material recycling in compliance with current legislation. As additional target polymers PC and PC-ABS were also recycled by dissolution but did not require an elimination of BFR. Finally, physicochemical investigations of recycled materials as gel permeation chromatography, melt flow rate, and differential scanning calorimetry suggest a high purity and indicate no degradation of the technical properties of the recycled polymers.