A review on polyester and polyester-amide thin film composite nanofiltration membranes: Synthesis, characteristics and applications

Fabrication of hollow fiber composite membranes via opposite transmission reaction method for dye/salt separation

The separation layer prepared by the conventional coating-crosslinking method is typically thick and prone to forming defective macropores, significantly affecting the water permeability and dye/salt separation performance of membranes. This work presented a novel method to prepare hollow fiber composite membranes for dye/salt separation based on the opposite transmission reaction of crosslinker. In this method, the macromolecule in situ reacted with a small-molecule crosslinker at the openings of membrane pore channels, forming a separation layer with discontinuous sheet-like and granular structure. Compared to the conventional forward coating-crosslinking method, the separation layer prepared by the opposite transmission reaction method exhibited an ultra-thin thickness of 29.1 nm. Consequently, the composite membrane exhibited a high water permeability of 72.7 L·m-2·h-1·bar-1, which was 2.3 times higher than that of conventional methods. Moreover, the prepared composite membrane presented a more uniformed pore structure, completely retaining the VBB (100%) with a low Na2SO4 rejection of 4.3%, demonstrating excellent dye/salt separation performance. Additionally, the prepared composite membrane exhibited superior anti-fouling properties compared to that prepared by the conventional method. Therefore, the opposite transmission reaction method proposed in this study held promising applications in the preparation of hollow fiber composite membranes for efficient dye/salt separation.

Recent Advances in the Titanium-Based Catalysts for Ring-Opening Polymerization

At present, economic development and daily life cannot be separated from organic synthetic polymers. However, a large number of nondegradable polymers have caused serious pollution to the environment. It is necessary for sustainable development to use biodegradable materials instead of traditional polymers, but it is not yet comparable in performance and cost to the competitor it will replace. Therefore, there is a long way to go to develop effective synthesis methods. Through ring-opening polymerization, some cyclic monomers, such as ε-caprolactone or lactide, can be synthesized into biodegradable polymers, which can not only replace traditional synthetic polymers in some fields but also have applications in drug delivery, surgical consumables, human implant materials, bone materials, etc. Ring-opening polymerization is a potential candidate for solving environmental pollution. For ring-opening polymerization, catalysts are very important, among which titanium catalysts have attracted much attention because of their high efficiency, economy, and nontoxicity. In this paper, the development status of organotitanium compounds as ring-opening polymerization catalysts is reviewed, including the effects of different ligand structures on polymerization behavior and polymer structure, and its development trend is prospected. We hope that this review will be helpful for developing efficient ring-opening polymerization catalysts.

Energy-efficient trehalose-based polyester nanofiltration membranes for zero-discharge textile wastewater treatment

Recovery of water, salts, and hazardous dye from complex saline textile wastewater faces obstacles in separating dissolved ionic substances and recovering organic components during desalination. This study realized the simultaneous fractionation, desalination, and dye removal/recovery treatment of textile wastewater by using trehalose (Tre) as an aqueous monomer to prepare polyester loose nanofiltration (LNF) membrane with fine control microstructure via interfacial polymerization. Outperforming the NF270 commercial membrane, the Tre-1.05/TMC optimized membrane achieves zero-discharge textile wastewater treatment, cutting energy consumption by 295% and reducing water consumption by 42.8%. This efficiency surge results from remarkable water permeability (130.83 L m-2 h-1 bar-1) and impressive dye desalination (NaCl/ Direct Red 23 separation factor of 275) of the Tre-1.05/TMC membrane. For a deeper comprehension of filtration performance, the sieving mechanism of polyester LNF membranes was systematically elucidated. This strategic approach offers significant prospects for energy conservation, carbon emission mitigation, and enhanced feasibility of membrane-based wastewater treatment systems.

Polyester Nanofiltration Membranes for Efficient Cations Separation

Polyester nanofiltration membranes highlight beneficial chlorine resistance, but their loose structures and negative charge result in poor cations retention precluding advanced use in cations separation. This work designs a new monomer (TET) containing "hydroxyl-ammonium" entities that confer dense structures and positive charge to polyester nanofiltration membranes. The TET monomer undergoes efficient interfacial polymerization with the trimesoyl chloride (TMC) monomer, and the resultant TET-TMC membranes feature one of the lowest molecular weight cut-offs (389 Da) and the highest zeta potential (4 mv, pH: 7) among all polyester nanofiltration membranes. The MgCl2 rejection of the TET-TMC membrane is 95.5%, significantly higher than state-of-the-art polyester nanofiltration membranes (<50%). The Li+ /Mg2+ separation performance of TET-TMC membrane is on par with cutting-edge polyamide membranes, while additionally, the membrane is stable against NaClO though polyamide membranes readily degrade. Thus the TET-TMC is the first polyester nanofiltration membrane for efficient cations separation.

Recent advances in cellulose- and alginate-based hydrogels for water and wastewater treatment: A review

From the environmental perspective, it is essential to develop cheap, eco-friendly, and highly efficient materials for water and wastewater treatment. In this regard, hydrogels and hydrogel-based composites have been widely employed to mitigate global water pollution as this methodology is simple and free from harmful by-products. Notably, alginate and cellulose, which are natural carbohydrate polymers, have gained great attention for their availability, price competitiveness, excellent biodegradability, biocompatibility, hydrophilicity, and superior physicochemical performance in water treatment. This review outlined the recent progress in developing and applying alginate- and cellulose-based hydrogels to remove various pollutants such as dyes, heavy metals, oils, pharmaceutical contaminants, and pesticides from wastewater streams. This review also highlighted the effects of various physical or chemical methods, such as crosslinking, grafting, the addition of fillers, nanoparticle incorporation, and polymer blending, on the physiochemical and adsorption properties of hydrogels. In addition, this review covered the alginate- and cellulose-based hydrogels' current limitations such as low mechanical performance and poor stability, while presenting strategies to improve the drawbacks of the hydrogels. Lastly, we discussed the prospects and future directions of alginate- and cellulose-based hydrogels. We hope this review provides valuable insights into the efficient preparations and applications of hydrogels.

Pressure-driven membrane filtration technology for terminal control of organic DBPs: A review

Disinfection by-products (DBPs), a series of undesired secondary contaminants formed during the disinfection processes, deteriorate water quality, threaten human health and endanger ecological safety. Membrane-filtration technologies are commonly used in the advanced water treatment and have shown a promising performance for removing trace contaminants. In order to gain a clearer understanding of the behavior of DBPs in membrane-filtration processes, this work dedicated to: (1) comprehensively reviewed the retention efficiency of microfiltration (MF), ultrafiltration (UF), nanofiltration (NF) and reverse osmosis (RO) for DBPs. (2) summarized the mechanisms involved size exclusion, electrostatic repulsion and adsorption in the membrane retention of DBPs. (3) In conjunction with principal component analysis, discussed the influence of various factors (such as the characteristics of membrane and DBPs, feed solution composition and operating conditions) on the removal efficiency. In general, the characteristics of the membranes (salt rejection, molecular weight cut-off, zeta potential, etc.) and DBPs (molecular size, electrical property, hydrophobicity, polarity, etc.) fundamentally determine the membrane-filtration performance on retaining DBPs, and the actual operating environmental factors (such as solute concentration, coexisting ions/NOMs, pH and transmembrane pressure) exert a positive/negative impact on performance to some extent. Current researches indicate that NF and RO can be effective in removing DBPs, and looking forward, we recommend that multiple factors should be taken into account that optimize the existed membrane-filtration technologies, rationalize the selection of membrane products, and develop novel membrane materials targeting the removal of DBPs.

Interfacial polymerization at unconventional interfaces: an emerging strategy to tailor thin-film composite membranes

Interfacial polymerization is a well-known process to synthesize separation layers for thin film composite membranes at an immiscible organic liquid-aqueous liquid interface. The organic-aqueous interface determines the diffusion dynamics of monomers and the chemical environment for polymerization, exerting a critical influence on the formation of polymer thin films. This review summarizes recent advances in tailoring interfacial polymerization using interfaces beyond the conventional alkane-water interface to achieve high-performance separation films with designed structures. Diverse liquid-liquid interfaces are introduced for synthesizing separation films by adding co-solvents into the organic phase and/or the aqueous phase, respectively, or by replacing one of the liquid phases with other solvents. Innovative liquid-gel and liquid-gas interfaces are then summarized for the synthesis of polymer thin films for separation. Novel strategies to form reaction interfaces, such as spray-coating, are also presented and discussed. In addition, we discuss the details of how a physically or chemically patterned substrate affects interfacial polymerization. Finally, the potential of unconventional interfaces in interfacial polymerization is forecast with both challenges and opportunities.

Preparation of a Solvent-Resistant Nanofiltration Membrane of Liquefied Walnut Shell Modified by Ethylenediamine

N,N-dimethylformamide (DMF) has excellent chemical stability and is widely used as an aprotic polar solvent. In order to reduce production costs and reduce pollution to the surrounding environment, it is necessary to recycle and reuse DMF. Previous research has found that the thin film composite nanofiltration membrane prepared from liquefied walnut shells exhibited a high rejection rate in DMF, but relatively low permeance and mechanical strength. In order to increase permeance without compromising the separation performance, ethylenediamine (EDA) is used as a modifier to graft onto the structure of liquefied walnut shell through the Mannich reaction. Then, modified liquefied walnut shell as an aqueous monomer reacts with trimesoyl chloride (TMC) via the interfacial polymerization method on the EDA-crosslinked polyetherimide (PEI) membrane. The results show that the permeance of the prepared membrane is significantly improved by an order of magnitude, demonstrating a rejection rate of 98% for crystal violet (CV), and a permeance of 3.53 L m-2 h-1 bar-1 in DMF. In conclusion, this study reveals the potential of utilizing liquefied walnut shells as raw materials for preparing high-performance separation membranes and demonstrates that surface modification is a feasible approach to enhance permeance of membranes without sacrificing the rejection rate.

Membrane processes for environmental remediation of nanomaterials: Potentials and challenges

Nanomaterials have gained huge attention with their wide range of applications. This is mainly driven by their unique properties. Nanomaterials include nanoparticles, nanotubes, nanofibers, and many other nanoscale structures have been widely assessed for improving the performance in different applications. However, with the wide implementation and utilization of nanomaterials, another challenge is being present when these materials end up in the environment, i.e. air, water, and soil. Environmental remediation of nanomaterials has recently gained attention and is concerned with removing nanomaterials from the environment. Membrane filtration processes have been widely considered a very efficient tool for the environmental remediation of different pollutants. Membranes with their different operating principles from size exclusions as in microfiltration, to ionic exclusion as in reverse osmosis, provide an effective tool for the removal of different types of nanomaterials. This work comprehends, summarizes, and critically discusses the different approaches for the environmental remediation of engineered nanomaterials using membrane filtration processes. Microfiltration (MF), ultrafiltration (UF), and nanofiltration (NF) have been shown to effectively remove nanomaterials from the air and aqueous environments. In MF, the adsorption of nanomaterials to membrane material was found to be the main removal mechanism. While in UF and NF, the main mechanism was size exclusion. Membrane fouling, hence requiring proper cleaning or replacement was found to be the major challenge for UF and NF processes. While limited adsorption capacity of nanomaterial along with desorption was found to be the main challenges for MF.

Strong, flexible and UV-shielding composite polyvinyl alcohol films with wood cellulose skeleton and lignin nanoparticles

The development of high-performance composite films using biomass materials have become a sought-after direction. Herein, a green method to fabricate strong, flexible and UV-shielding biological composite film from wood cellulose skeleton (WCS), lignin nanoparticles (LNPs) and polyvinyl alcohol (PVA) was described. In the work, WCS and LNPs were prepared by chemical treatment of wood veneer and Enzymatic lignin, respectively. Then, WCS was infiltrated with the LNPs/PVA mixtures and dried to obtain composite films. WCS enhanced the mechanical properties of the composite films, the tensile stress reached to 85.8 MPa and the tensile strain reached to 6.39 %. The composite films with LNPs blocked over 98 % of UV-light, the water absorption decreased by 30 %, and the thermal stabilities were also improved. These findings would provide some references for exploring high quality biological composite films.

Recent Advanced Development of Acid-Resistant Thin-Film Composite Nanofiltration Membrane Preparation and Separation Performance in Acidic Environments

Membrane filtration technology has attracted extensive attention in academia and industry due to its advantages of eco-friendliness related to environmental protection and high efficiency. Polyamide thin-film composite nanofiltration (PA TFC NF) membranes have been widely used due to their high separation performance. Non-acid-resistant PA TFC NF membranes face tremendous challenges in an acidic environment. Novel and relatively acid-resistant polysulfonamide-based and triazine-based TFC NF membranes have been developed, but these have a serious trade-off in terms of permeability and selectivity. Hence, how to improve acid resistance of TFC NF membranes and their separation performance in acidic environments is a pivotal issue for the design and preparation of these membranes. This review first highlights current strategies for improving the acid resistance of PA TFC NF membranes by regulating the composition and structure of the separation layer of the membrane performed by manipulating and optimizing the construction method and then summarizes the separation performances of these acid-resistant TFC NF membranes in acidic environments, as studied in recent years.