Fabrication and characterization of novel PES/Fe–Mn binary oxide UF mixed matrix membrane for adsorptive removal of As(III) from contaminated water solution

Application of manganese oxide-based materials for arsenic removal: A review

In the context of growing arsenic (As) contamination in the world, there is an urgent need for an effective treatment approach to remove As from the environment. Industrial wastewater is one of the primary sources of As contamination, which poses significant risks to both microorganisms and human health, as the presence of As can disrupt the vital processes and synthesis of crucial macromolecules in living organisms. The global apprehension regarding As presence in aquatic environments persists as a key environmental issue. This review summarizes the recent advances and progress in the design, strategy, and synthesis method of various manganese-based adsorbent materials for As removal. Occurrence, removal, oxidation mechanism of As(III), As adsorption on manganese oxide (MnOx)-based materials, and influence of co-existing solutes are also discussed. Furthermore, the existing knowledge gaps of MnOx-based adsorbent materials and future research directions are proposed. This review provides a reference for the application of MnOx-based adsorbent materials to As removal.

Recent advances in application of iron-manganese oxide nanomaterials for removal of heavy metals in the aquatic environment

Heavy metal pollution has a serious negative impact on the ecological environment and human health due to its toxicity, persistence, and non-biodegradable properties. Among the technologies applied in heavy metals removal, adsorption has been widely used as the most promising method because of its simple operation, high removal efficiency, strong applicability, and low cost. Iron-manganese oxide nanomaterials, as an effective absorbent, have attracted wide attention due to their simple preparation, wide material sources, and lower ecological impact. So far, no quantitative investigation has been conducted on the preparation and application of iron-manganese oxide nanomaterials in heavy metals removal. This review discussed the preparation methods and characteristics of iron‑manganese oxide nanomaterials over the past decade and provided some basic information for the improvement of preparation methods. The physicochemical properties of iron‑manganese oxide nanomaterials and environmental conditions are regarded as important factors that affect the removal efficiency of heavy metals. In addition, the removal mechanisms of heavy metals in aqueous solution with iron‑manganese oxide nanomaterials were mainly included redox, complex precipitation, electrostatic attraction, and ion exchange. The reusability and practicability in actual wastewater treatment of 3nganese oxide nanomaterials were further discussed. Several key problems still need to be solved in the existing progress, such as improving the ability and stability of the iron‑manganese oxide nanomaterials to remove heavy metals from actual wastewater. In conclusion, this review provides a future direction for the application of iron‑manganese oxide nanomaterials for heavy metals removal and even in the large-scale treatment of actual wastewater.

Review of Thin Film Nanocomposite Membranes and Their Applications in Desalination

All over the world, almost one billion people live in regions where water is scarce. It is also estimated that by 2035, almost 3.5 billion people will be experiencing water scarcity. Hence, there is a need for water based technologies. In separation processes, membrane based technologies have been a popular choice due to its advantages over other techniques. In recent decades, sustained research in the field of membrane technology has seen a remarkable surge in the development of membrane technology, particularly because of reduction of energy footprints and cost. One such development is the inclusion of nanoparticles in thin film composite membranes, commonly referred to as Thin Film Nanocomposite Membranes (TFN). This review covers the development, characteristics, advantages, and applications of TFN technology since its introduction in 2007 by Hoek. After a brief overview on the existing membrane technology, this review discusses TFN membranes. This discussion includes TFN membrane synthesis, characterization, and enhanced properties due to the incorporation of nanoparticles. An attempt is made to summarize the various nanoparticles used for preparing TFNs and the effects they have on membrane performance towards desalination. The improvement in membrane performance is generally observed in properties such as permeability, selectivity, chlorine stability, and antifouling. Subsequently, the application of TFNs in Reverse Osmosis (RO) alongside other desalination alternatives like Multiple Effect Flash evaporator and Multi-Stage Flash distillation is covered.

Mixed-Matrix Membrane Fabrication for Water Treatment

In recent years, technology for the fabrication of mixed-matrix membranes has received significant research interest due to the widespread use of mixed-matrix membranes (MMMs) for various separation processes, as well as biomedical applications. MMMs possess a wide range of properties, including selectivity, good permeability of desired liquid or gas, antifouling behavior, and desired mechanical strength, which makes them preferable for research nowadays. However, these properties of MMMs are due to their tailored and designed structure, which is possible due to a fabrication process with controlled fabrication parameters and a choice of appropriate materials, such as a polymer matrix with dispersed nanoparticulates based on a typical application. Therefore, several conventional fabrication methods such as a phase-inversion process, interfacial polymerization, co-casting, coating, electrospinning, etc., have been implemented for MMM preparation, and there is a drive for continuous modification of advanced, easy, and economic MMM fabrication technology for industrial-, small-, and bulk-scale production. This review focuses on different MMM fabrication processes and the importance of various parameter controls and membrane efficiency, as well as tackling membrane fouling with the use of nanomaterials in MMMs. Finally, future challenges and outlooks are highlighted.

A review on surface modification methods of poly(arylsulfone) membranes for biomedical applications

Considerable methods have so far been used for the surface modification of biomedical membranes. Several reviews and articles have been published on the improvements achieved in the field of poly(arylsulfone) membranes subjected to various surface modification methods and used in biomedical applications. This review concentrates on the surface modification, biological applications and future perspective of the poly(arylsulfone) biomedical membranes. Different surface modification procedures employed for the poly(arylsulfone) membranes have been classified, studied and compared. Diverse surface modification techniques include surface coating, chemical modification and immobilization/cross-linking, grafting, surface zwitterionicalization, mussel-inspired coating and layer-by-layer assembly. Furthermore, we review the recent research studies performed on the surface modification of the poly(arylsulfone) biomedical membranes. Meanwhile, the properties of biomedical membranes are also discussed in each section. At last, the future perspective and challenges of the strategies utilized for the surface modification of poly(arylsulfone) biomedical membranes are presented.

Preparation of PVDF/FMBO composite electrospun nanofiber for effective arsenate removal from water

In this study, novel electrospun nanofibers (NFs) composed of organic polyvinylidine fluoride (PVDF) and inorganic Fe-Mn binary oxide (FMBO) nanoparticles were fabricated using an electrospinning technique for adsorptive decontamination of As(v) from polluted water. The NFs were prepared with doped solutions consisting of different weight ratios of PVDF/FMBO, in a NF matrix, ranging from 0 to 0.5. SEM, XRD, FTIR and TEM then characterized the NFs and FMBO particles. The XRD analysis indicated successful impregnation of FMBO nanoparticles in the NF matrix of the NFs investigated. An As(v) adsorption capacity as high as around 21.32 mg g-1 was obtained using the NF containing the highest amount of FMBO nanoparticles (designated as PVDF/FMBO 0.5). Furthermore, the adsorptive performance of the PVDF/FMBO 0.5 nanofiber could be easily regenerated using diluted alkaline solution (NaOH and NaOCl).

Gene expression programming for process parameter optimization during ultrafiltration of surfactant wastewater using hydrophilic polyethersulfone membrane

Surfactants are the emerging contaminant and cause a detrimental effect on the ecosystem. In this study, an attempt is made to removal anionic surfactant Sodium dodecyl sulfate (SDS) containing wastewater using hydrophilic polyvinylpyrollidone (PVP) (5-15 wt%) modified polyethersulfone (PES) ultrafiltration membrane. The influence of operating variables on membrane performance was also sequentially analyzed using tests and three numerical modeling methods such as multiple linear regression (MLR), multiple Ln-equation regression (MLnER), and gene expression programming (GEP). Contact angle value of 10 wt% PVP modified PES membrane decreased up to 23.8°, whereas the neat PES membrane is 70.7°. This study indicates that the required hydrophilic property was improved in the modified membrane. The water flux and porosity also enhanced in PVP modified PES membranes. In performance evaluation, the optimum operating variable condition of transmembrane pressure (TMP), feed concentration, and the temperature is found to be 3 bar, 100 ppm, and 25 °C, respectively. Among the models, GEP has a good correlation with experimental anionic surfactant SDS filtration data. GEP performs better than other model with respect to statistical parameter and error terms. This study provides an insight into an adaptation of novel numerical modeling methods for the prediction of membrane performance to the treatment of surfactant wastewater.

Enhanced As(Ш) removal from aqueous solutions by recyclable Cu@MNM composite membranes via synergistic oxidation and absorption

Arsenic contamination threatens the safety of drinking water in many parts of the world, especially As (Ш), which is more toxic and more difficult to remove than As (Ⅴ). Hence, in terms of environmental protection and sustainable development, it is very important to remove As (Ш) from the environment to reduce the damage to ecosystems and human health. Since there is no effective method for removing As (Ш), it is essential to oxidize As (Ш) into easily removable As (Ⅴ) to achieve effective separation. Herein, a novel copper-coated MnO₂ nanowires membrane (Cu@MNM) which combines the oxidation properties of MnO₂ and the catalytic and absorption properties of nanoscale Cu (NSCu), was developed based on in situ chemical deposition NSCu on the surface of ultralong MnO₂ nanowires. The as-prepared Cu@MNM shows excellent arsenic separation properties with the maximum rejection rate of 96%. The results of pH studies indicate that acidic conditions promote the separation of As (Ш) by Cu@MNM, while alkaline conditions are inhibitory due to deprotonation of Cu@MNM surface enhances electrostatic repulsion. The results of the interfering ions show that the phosphate ions have a strong inhibitory effect on arsenic separation. In addition, Cu@MNM has been shown to be remarkably recyclable and can still achieve a separation efficiency of 60% after five cycles. Therefore, the prepared Cu@MNM with the high arsenic retention efficiency and excellent recycling capabilities has the potential to become an excellent candidate for practical application in arsenic separation.

Adsorptive nanocomposite membranes for heavy metal remediation: Recent progresses and challenges

Heavy metal contamination in aqueous system has attracted global attention due to the toxicity and carcinogenicity effects towards living bodies. Among available removal techniques, adsorptive removal by nanosized materials such as metal oxide, metal organic frameworks, zeolite and carbon-based materials has attracted much attention due to the large active surface area, large number of functional groups, high chemical and thermal stability which led to outstanding adsorption performance. However, the usage of nanosized materials is restricted by the difficulty in separating the spent adsorbent from aqueous solution. The shift towards the use of adsorptive composite membrane for heavy metal ions removal has attracted much attention due to the synergistic properties of adsorption and filtration approaches in a same chamber. Thus, this review critically discusses the development of nanoadsorbents and adsorptive nanocomposite membranes for heavy metal removal over the last decade. The adsorption mechanism of heavy metal ions by the advanced nanoadsorbents is also discussed using kinetic and isotherm models. The challenges and future prospect of adsorptive membrane technology for heavy metal removal is presented at the end of this review.

Application of modified electrospun nanofiber membranes with α-Fe2O3 nanoparticles in arsenate removal from aqueous media

In the present study, electrospun nanofiber membranes (ENMs) of polyacrylonitrile (PAN) were modified by dispersing α-Fe₂O₃ nanoparticles, synthesized using a thermal solvent process, in a PAN solution. The morphology and physiochemical properties of the prepared ENMs and the α-Fe₂O₃ were characterized using FESEM, EDX, BET, XRD, FTIR, porosity, and contact angle measurement. XPS was used to investigate the interaction of ENM with arsenate (As(V)) during the adsorption. Moreover, the effect of pH, the equilibrium isotherm, and the kinetics were investigated in batch experiments. The Langmuir isotherm best correlated the experimental results, indicating monolayer adsorption on ENMs, and the kinetics was best fitted, R² > 0.99, by the pseudo-second-order model. In addition, the effects of certain conditions on the filtration performance were examined, such as feed concentration and transmembrane pressure (TMP). By passing sodium hydroxide (0.1 M) for 20 min, the membrane was regenerated. The increase in TMP, along with the presence of co-ions including chloride, nitrate, and sulfate, had negative impacts on the removal of As(V). The results show that the modified ENMs with α-Fe₂O₃ nanoparticles are applicable for As(V) ion removal and possibly for eliminating other heavy metals from aqueous media.

Hydrous ferric oxide nanoparticles hosted porous polyethersulfone adsorptive membrane: chromium (VI) adsorptive studies and its applicability for water/wastewater treatment

In this present study, adsorptive membranes for Cr(VI) ion removal were prepared by blending polyethersulfone (PES) with hydrous ferric oxide (HFO) nanoparticles (NPs). The effects of HFO NPs to PES weight ratio (0-1.5) on the physicochemical properties of the resultant HFO/PES adsorptive membranes were investigated with respect to the surface chemistry and roughness as well as structural morphologies using different analytical instruments. The adsorptive performance of the HFO NPs/PES membranes was studied via batch adsorption experiments under various conditions by varying solution pH, initial concentration of Cr(VI), and contact time. The results showed that the membrane made of HFO/PES at a weight ratio of 1.0 exhibited the highest adsorption capacity which is 13.5 mg/g. Isotherm and kinetic studies revealed that the mechanism is best fitted to the Langmuir model and pseudo-second-order model. For filtration of Cr(VI), the best promising membranes showed improved water flux (629.3 L/m² h) with Cr(VI) ion removal of 75%. More importantly, the newly developed membrane maintained the Cr(VI) concentration below the maximum contamination level (MCL) for up to 9 h.

Equilibrium, kinetic and thermodynamic study of pesticides removal from water using novel glucamine-calix[4]arene functionalized magnetic graphene oxide

A novel nanocomposite of MGO-NGC, composed of magnetic Fe3O4 nanoparticles (M), graphene oxide (GO), and N-methyl-d-glucamine functionalized calix[4]arene (NGC), was synthesized and applied as an effective adsorbent for the removal of two selected pesticides, namely hexaconazole and chlorpyrifos from water samples. The adsorbent was characterized by FTIR, SEM, EDX, TEM, and XRD. The main parameters affecting the adsorption process such as adsorbent dosage, pH of sample solution, salt effect, pesticide concentration, and adsorption time were investigated. The data from kinetic studies fitted well to the pseudo-second order kinetic model with R2 > 0.99. Among the isotherm models of Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich, the Langmuir isotherm fitted well to the adsorption process and demonstrated the monolayer adsorption pattern of the pesticides. Moreover, high adsorption capacities of 78.74 and 93.46 mg g-1 were obtained for chlorpyrifos and hexaconazole, respectively. Thermodynamic and free energy data indicated the physisorption mechanism for the adsorption process. The new adsorbent can be employed as an efficient, environment friendly, and highly reusable alternative for the removal of chlorinated pesticides from aqueous media.

In situ-generated yttrium-based nanoparticle/polyethersulfone composite adsorptive membranes: Development, characterization, and membrane formation mechanism

In this study, a series of in situ-generated yttrium-based nanoparticle (NP)/polyethersulfone (PES) composite adsorptive membranes were prepared by the phase inversion method for the first time. The Y(NO₃)₃·6H₂O as precursor, uniformly dispersed at the molecular level in casting solution, reacted with OH^- in a coagulation bath and ambient CO₂ during the phase inversion process. The Y(CO₃)_0.5(OH)₂ NPs were formed in situ and distributed homogeneously in a PES matrix, which was confirmed by X-ray photoelectron spectroscopy (XPS) and Energy Dispersive X-Ray Spectroscopy (EDS) results. The compatibility of the nanocomposite membranes was improved by an in situ preparation method. With the increase in content of Y-based NPs in composite membranes, the surface hydrophilicity and water permeability first increased from M1 to M2, and then slightly decreased from M3 to M5, which was mainly related to membrane structure. From M1 to M5, the demixing way changed from instantaneous demixing to delayed demixing process as a result of thermodynamic enhancement and viscosity hindrance in the phase inversion process. A higher demixing rate led to a structure with large finger-like macro-voids, i.e., M1, whereas a lower demixing rate caused the suppression of finger-like macro-voids, i.e., M5. More importantly, the adsorption study indicated that the nanocomposite adsorptive membranes were stable in the treatment of fluoride-containing water, with no leakage of Y-based NPs from membrane matrix to solution. It is expected that the in situ preparation technique could be used to produce next-generation nanocomposite adsorptive membranes with improved comprehensive properties for application in water treatment.

Polyethersulfone Membranes Prepared with 3-Aminopropyltriethoxysilane Modified Alumina Nanoparticles for Cu(II) Removal from Water

In this study, 3-aminopropyltriethoxysilane (APTES) modified γ-alumina nanoparticles were utilized to improve the copper removal efficiency of polyethersulfone (PES) membranes. Alumina nanoparticles were first modified by APTES silane coupling agent before impregnating into PES composite membranes. The PES membranes were fabricated by incorporating three different amounts of modified nanoparticles by a phase inversion process. The prepared membranes were characterized using field emission scanning electron microscopy, Fourier transform infrared, X-ray diffraction, thermogravimetric analysis (TGA), dynamic mechanical analysis, water contact angle, water flux, and porosity measurements. The Cu(II) removal and adsorption capacity of the membranes were also analyzed. The addition of nanoparticles increased the thermal stability, hydrophilicity, total porosity, Brunauer-Emmett-Teller surface area, and glass transition temperature of the membranes. TGA confirmed a suitable uptake of the nanoparticles during the membrane fabrication process. The water permeation of the membranes also increased significantly. Membranes synthesized with 4 wt % nanoparticles showed the highest rejection for copper ions of 87%. Adsorption isotherms were tested using Langmuir and Freundlich models, where the Freundlich isotherm model resulted in the best fitting.

Efficient removal of arsenic(III) from aqueous media using magnetic polyaniline-doped strontium-titanium nanocomposite

In this study, a novel nanocomposite adsorbent based on magnetic polyaniline and strontium-titanium (MP-SrTiO₃) nanoparticles was synthesized via a simple and low-cost polymerization method for efficiently removing of arsenic(III) ions from aqueous samples. The chemical structure, surface properties, and morphology of the prepared adsorbent were studied using Fourier transform infrared spectroscopy (FTIR), energy-dispersive X-ray spectroscopy (EDX), and scanning electron microscopy (SEM). The main effective parameters on the removal efficiency, such as pH, adsorbent dosage, salt, and contact time, were studied and optimized. The validity of the proposed method was checked by adsorption isotherm and kinetics models. Consequently, the adsorption kinetics corresponded to the first order (R² > 0.99), and the experimental equilibrium fitted the Langmuir model with a maximum monolayer adsorption capacity of 67.11 mg/g (R² > 0.99) for arsenic(III) ions. Corresponding to thermodynamic Vant's Hof model (ΔG° (kJ/mol), ΔH° (kJ/mol), and ΔS° (kJ/mol K) - 8.19, - 60.61, and - 0.17, respectively), the mechanism and adsorption nature were investigated with that suggested exothermic and physisorption mechanism.

PES-Kaolin Mixed Matrix Membranes for Arsenic Removal from Water

The aim of this work was the fabrication and the characterization of mixed matrix membranes (MMMs) for arsenic (As) removal from water. Membrane separation was combined with an adsorption process by incorporating the kaolin (KT2) Algerian natural clay in polymeric membranes. The effects of casting solution composition was explored using different amounts of polyethersufone (PES) as a polymer, polyvinyl-pyrrolidone (PVP K17) and polyethylene glycol (PEG 200) as pore former agents, N-methyl pyrrolidone (NMP) as a solvent, and kaolin. Membranes were prepared by coupling Non-solvent Induced Phase Separation and Vapour Induced Phase Separation (NIPS and VIPS, respectively). The influence of the exposure time to controlled humid air and temperature was also investigated. The MMMs obtained were characterized in terms of morphology, pore size, porosity, thickness, contact angle and pure water permeability. Adsorption membrane-based tests were carried out in order to assess the applicability of the membranes produced for As removal from contaminated water. Among the investigated kaolin concentrations (ranging from 0 wt % to 5 wt %), a content of 1.25 wt % led to the MMM with the most promising performance.

Synthesis of piperazine functionalized magnetic sporopollenin: a new organic-inorganic hybrid material for the removal of lead(II) and arsenic(III) from aqueous solution

The present work describes the successful functionalization/magnetization of bio-polymeric spores of Lycopodium clavatum (sporopollenin) with 1-(2-hydroxyethyl) piperazine. Analytical techniques, i.e., Fourier transform infrared (FT-IR), field emission scanning electron microscope (FESEM), energy-dispersive X-ray spectroscopy (EDS), and vibrating sample magnetometer (VSM), were used to confirm the formation of 1-(2-hydroxyethyl) piperazine-functionalized magnetic sporopollenin (MNPs-Sp-HEP). The proposed adsorbent (MNPs-Sp-HEP) was used for the removal of noxious Pb(II) and As(III) metal ions from aqueous media through a batch-wise method. Different experimental parameters were optimized for the effective removal of selected noxious metal ions. Maximum adsorption capacity (q _m ) 13.36 and 69.85 mg g^-1 for Pb(II) and As(III), respectively, were obtained. Thermodynamic parameters such as free energy (ΔG°), entropy (ΔS°), and enthalpy (ΔH°) were also studied from the adsorption results and were used to elaborate the mechanism of their confiscation. The obtained results indicated that newly adsorbent can be successfully applied for the decontamination of noxious Pb(II) and As(III) from the aqueous environment.

Bio-adsorbent derived from papaya peel waste and magnetic nanoparticles fabricated for lead determination

Determination of toxic lead ions at trace level using solid-based adsorbents has become of interest in recent years. In this work, a novel bio-adsorbent originating from papaya peel waste (PPw) and magnetic nanoparticles (Fe3O4) was developed (Fe3O4/PPw). The new adsorbent was prepared using a one-pot green method and characterized by Fourier transform infrared, X-ray diffractometer, energy-dispersive X-ray spectroscopy and field emission scanning electron microscopy. The synthesized Fe3O4/PPw was used as a magnetic solid-phase extraction (MSPE) sorbent for extraction of lead ions from waste water prior to assessing by flame atomic absorption spectroscopy. The parameters influencing extraction recovery, including desorption solvent, solvent volume, sample volume, extraction time, desorption time, adsorbent dosage, salt effect and pH were optimized. A linear response for the MSPE method was achieved at concentrations from 10 to 100 ng mL−1 with a good coefficient of determination (R 2=0.9987). Detection limits and quantitation limit of the MSPE method were observed around 2 ng mL−1 and 6.6 ng mL−1, respectively. The intraday and interday precision (%RSD) was in the range 1.6%–4.5% and 2.3%–7.4%, respectively. The recovery amounts obtained were 91% for tap water, 85.9% for river water and 86% for waste water. The synthesized adsorbent showed a minimum reusability of eight cycles without significant change in the lead determination. The results proved that the new bio-adsorbent (Fe3O4/PPw) is potentially capable to extract the Pb(II) from aqueous media under optimum conditions with a high extraction efficiency.

Nano-structured magneto-responsive membranes from block copolymers and iron oxide nanoparticles

Preparation of porous membranes from PMAA-b-PMMA copolymers and magnetic iron oxide nanoparticles and their performance under magnetic fields.

Treatment of laundry wastewater using polyethersulfone/polyvinylpyrollidone ultrafiltration membranes

In this study, laundry wastewater filtration was studied using hydrophilic polyvinylpyrollidone (PVP) modified polyethersulfone (PES) ultrafiltration membranes. The performances of PES/PVP membranes were assessed using commercial PES membrane with 10kDa in ultrafiltration. Operating parameters The influence of transmembrane pressure (TMP) and stirring speed on laundry wastewater flux was investigated. A higher permeate flux of 55.2L/m(2)h was obtained for modified PES membrane with high concentration of PVP at TMP of 500kPa and 750rpm of stirring speed. The separation efficiencies of membranes were also studied with respect to chemical oxygen demand (COD), total dissolved solids (TDS), turbidity and conductivity. Results showed that PES membrane with 10% of PVP had higher permeate flux, flux recovery and less fouling when compared with other membranes. Higher COD and TDS rejection of 88% and 82% were also observed for modified membranes due to the improved surface property of membranes. This indicated that modified PES membranes are suitable for the treatment of surfactant, detergent and oil from laundry wastewater.