Development of fouling-resistant polyethersulfone ultrafiltration membranes via surface UV photografting with polyethylene glycol/aluminum oxide nanoparticles

Nanodiamond embedded polyaniline/polyvinylidene fluoride nanocomposites as microfiltration membranes for removal of industrial pollution

Membrane fouling remains a challenge to the membrane technology. Herein, we report the fabrication of composite membranes of polyaniline/polyvinylidene fluoride (PANI/PVDF) blended with nanodiamond (ND) with improved antifouling properties. The designed membranes were characterized by XRD, FTIR and SEM techniques. Characterization analysis revealed that addition of ND has maintained the structural integrity and porosity of composite membranes. The membrane permeation and antifouling performances were tested for hydrophilicity, porosity, pure water flux, shrinkage ratio, salt rejection of zinc acetate and copper acetate, and their fouling recovery ratio (FRR) measurements. A high solvent content ratio of 0.55 and a low shrinkage ratio of <12% due to enhanced hydrophilicity and porosity of the composite membrane with fouling-recovery of membranes to 88% were achieved. Separation of copper and zinc ions from aqueous solution was achieved. These findings imply that ND-based PANI/PVDF composite membranes can effectively serve as microfiltration membranes in industrial and municipal wastewater treatment.

Surface Treatment by Physical Irradiation for Antifouling, Chlorine-Resistant RO Membranes

Reverse osmosis (RO) membranes represent a strategic tool for the development of desalination and water treatment processes. Today's global needs for clean water supplies show stressing circumstances to secure this supply, relying upon desalination and wastewater treatment and reuse, especially in Egypt and the Middle East. However, chlorine attack and fouling of polyamide layers, the active (selective) layers of RO membranes, are representing a great obstacle to seriously spreading the use of this technology. One promising way of fouling control and chlorine resistance is surface modification using grafting by plasma or vacuum ultraviolet (VUV) irradiation as a layer-by-layer assembly on polyamide membranes. Several studies have shown the effect of grafting by plasma using methacrylic acid (atmospheric pressure plasma) and showed that grafted coatings can improve PA membranes toward permeation compared with commercial ones with fouling behavior but not chlorine resistance. In this work, the techniques of layer-by-layer (LBL) assembly for previously prepared PA RO membranes (3T) using a mixed-base polymer of polysulfone and polyacrylonitrile in the presence of nanographene oxide (GO) without chemical grafting and with chemically grafted poly-methacrylic acid (3TG) were used. Membranes 3T, 3TG, a blank one (a base polymer membrane only was surface modified using VUV activation (AKT), and one with a grafted layer with polyethylene glycol (VUV-PEG) were prepared. These were then compared with polydimethylsiloxane (VUV-PDMS) and another surface modification with low-pressure plasma using acrylic acid (acryl) and hexadimethyl siloxane (GrowPLAS). The tested membranes were evaluated by short-term permeation and salt rejection experiments together with fouling behavior and chlorine resistance. A clear improvement of chlorine resistance and antifouling was observed for 3T membranes under plasma treatment, especially with the grafting with polyacrylic acid. Better antifouling and antichlorine behaviors were achieved with the vacuum UV treatment.

Ultrafiltration Membranes Functionalized with Copper Oxide and Zwitterions for Fouling Resistance

Polymeric membrane fouling is a long-standing challenge for water filtration. Metal/metal oxide nanoparticle functionalization of the membrane surface can impart anti-fouling properties through the reactivity of the metal species and the generation of radical species. Copper oxide nanoparticles (CuO NPs) are effective at reducing organic fouling when used in conjunction with hydrogen peroxide, but leaching of copper ions from the membrane has been observed, which can hinder the longevity of the CuO NP activity at the membrane surface. Zwitterions can reduce organic fouling and stabilize NP attachment, suggesting a potential opportunity to combine the two functionalizations. Here, we coated polyethersulfone (PES) ultrafiltration membranes with polydopamine (PDA) and attached the zwitterionic compound, thiolated 2-methacryloyloxyethyl phosphorylcholine (MPC-SH), and CuO NPs. Functionalized membranes resulted in a higher flux recovery ratio (0.694) than the unfunctionalized PES control (0.599). Copper retention was high (>96%) for functionalized membranes. The results indicate that CuO NPs and MPC-SH can reduce organic fouling with only limited copper leaching.

Hydrophilized Ultrafiltration Membranes Synthesized from Acrylic Acid Grafted Polyethersulfone for Downstream Processing of Therapeutic Insulin and Cobalamin

The present study focuses on synthesis of novel high-performance acrylic acid (AA) grafted polyethersulfone (PES) ultrafiltration (UF) membranes for purification of small therapeutic biomolecules such as urea, insulin, and cobalamin. The membranes were indigenously synthesized by adding polyethylene glycol (PEG) of 6 kDa M.Wt. as a pore former and subsequent grafting of AA using 2 to 6 wt.% concentrations under UV-induced photo grafting. Scanning electron microscopy reveals that the PEG additive profoundly influences the pore density on the membrane surface. FTIR spectra confirm the graft polymerization of AA with the PES substrate. Separation performance of the grafted membranes was evaluated to establish the trade-off between the degree of grafting and MWCO. From the experimental results, the pure water flux (PWF) of 6% grafted PES membrane was enhanced from 8.5 (PES [0] [6]) to 18.20 l m^-2 h^-1 (PES [6 +] [6]) in the presence of PEG pore former, respectively. The grafting concentration window of 2-6% resulted in selective membranes to altogether remove uremic toxins into the permeate with retention of high molecular size proteins. Hence, 5 and 6 wt.% AA grafted membranes exhibited > 90% rejection for insulin and cobalamin biomolecules along with 24.5 and 23.8 l m^-2 h^-1 bar^-1 permeability towards urea, respectively. The process results correlate well with the MWCO values of membranes ranging from 1 to 10 kDa. This work provides the efficacy of these grafted membranes for potential application in the downstream processing of therapeutic biomolecules such as insulin and cobalamin.

Polymeric membranes for biomedical applications

The rapid development of nanotechnology paved the way for further expansion of polymer chemistry and the fabrication of advanced polymeric membranes. Such modifications allowed enhancing or adding some unique properties, including mechanical strength, excellent biocompatibility, easily controlled degradability, and biological activity. This chapter discusses various applications of polymeric membranes in three significant areas of biomedicine, including tissue engineering, drug delivery systems, and diagnostics. It is intended to highlight here possible ways of improvement the properties of polymeric membranes, by modifying with other polymers, functional groups, compounds, drugs, bioactive components, and nanomaterials.

Removal of bovine serum albumin from wastewater using fouling resistant ultrafiltration membranes based on the blends of cellulose acetate, and PVP-TiO2 nanoparticles

Fouling resistant ultrafiltration membranes based on the blends of polyvinylpyrrolidone (PVP), TiO₂ nanoparticles and cellulose acetate, CA-PVP-TiO₂ (CATP), for removal of bovine serum albumin (BSA) were prepared by using phase inversion process. The influences of PVP and TiO₂ on the preparation of phase inverted cellulose acetate (CA) ultrafiltration membrane were explored in terms of morphology study, equilibrium water content (EWC), hydraulic resistance, permeability performance, hydrophilicity, and thermal stability. After the introduction of PVP and TiO₂ to the ternary (polymer-solvent-non-solvent) system, the formations of finger-like structures and macro-voids were reduced significantly. An improvement in porosity, average pore size, and hydrophilic nature of the CA membranes were detected after the introduction of PVP and TiO₂ into the polymer matrix. The interaction between TiO₂ and CA was confirmed and the degradation temperature of the CA membrane was significantly improved. BSA protein removal efficiency, anti-fouling performance, and recycling potential of the UF membranes were investigated. The CATP membrane (10.5 wt % CA: 4 wt % PVP: 2 wt % TiO₂) has displayed high BSA removal efficiency and flux recovery ratios (NFR) with enhanced anti-fouling performances for the three fouling/rinsing cycles.

Development of a nanocomposite ultrafiltration membrane based on polyphenylsulfone blended with graphene oxide

In the present study, graphene oxide (GO) was incorporated as a nanoadditive into a polyphenylsulfone (PPSU) to develop a PPSU/GO nanocomposite membrane with enhanced antifouling properties. A series of membranes containing different concentrations (0.2, 0.5 and 1.0 wt.%) of GO were fabricated via the phase inversion method, using N-methyl pyrrolidone (NMP) as the solvent, deionized water as the non-solvent, and polyvinylpyrrolidone (PVP) as a pore forming agent. The prepared nanocomposite membranes were characterized using scanning electron microscopy (SEM) and atomic force microscopy (AFM), and were also characterized with respect to contact angle, zeta potential and porosity, mean pore radius, tortuosity and molecular weight cut-off (MWCO). Thermogravimetric analysis (TGA) and tensile testing were used to measure thermal and mechanical properties. The membrane performance was evaluated by volumetric flux and rejection of proteins, and antifouling properties. According to the results, the optimum addition of 0.5 wt% GO resulted in a membrane with an increased flux of 171 ± 3 Lm⁻²h⁻¹ with a MWCO of ~40 kDa. In addition, the GO incorporation efficiently inhibited the interaction between proteins and the membrane surface, thereby improving the fouling resistance ability by approximately 58 ± 3%. Also, the resulting membranes showed a significant improvement in mechanical and thermal properties.

Preparation and characterization of latex films photo-immobilized with IFN-α

We developed a biomaterial by photo-immobilizing interferon-α (IFN-α) on the surface of latex condom films for the prevention and treatment of cervicitis, cervical cancers and diseases caused by cervical virus. The IFN-α modification by photoactive N-(4-azidobenzoyloxy) succinimide was characterized on a nano-scale by spectroscopy analysis and micro morphology. The anti-bacterial, anti-cancer, and anti-viral effects of the modified bioactive latex films were evaluated by antibacterial susceptibility testing, Gram staining, flow cytometry, immunofluorescence, and Western blotting. Our results showed that the photo-immobilized IFN-α latex films effectively inhibited the growth of both Neisseria gonorrhoeae and human cervical cancer HeLa cells. Moreover, the expression of anti-viral proteins, including P56, MxA, and 2', 5'-OAS, in the human cervical epithelial cell line NC104 was significantly increased by photo-immobilized IFN-α latex films. Taken together, these results suggest that photo-immobilized IFN-α latex films may have therapeutic effects against cervicitis, cervical cancers, and cervical virus.

Treatment of table olive processing wastewaters using novel photomodified ultrafiltration membranes as first step for recovering phenolic compounds

Table olive processing wastewaters (TOPW) have high salt concentration and total phenolic content (TPC) causing many environmental problems. To reduce them, ultrafiltration (UF) was applied for treating TOPW. However, NaCl, which is the main responsible of salinity in TOPW, and phenols are small molecules that cannot be separated by conventional UF membranes. They have serious problems caused by fouling, which can be overcome using membrane modification techniques. For these reasons, photomodification may be an effective technique to obtain a stream rich in TPC due to the changes in membrane surface properties. UV-modification in the presence of two hydrophilic compounds (polyethylene glycol and aluminium oxide) was performed to achieve membranes with high reductions of organic matter and to keep the TPC as high as possible. Commercial polyethersulfone (PES) membranes of 30 kDa were used. Surface modification was evaluated using FTIR-ATR spectroscopy and membrane performance was studied by calculating the rejection ratios of colour, chemical oxygen demand (COD) and TPC. Results demonstrated that UF is a useful pre-treatment to reduce organic matter from TOPW, obtaining a permeate rich in TPC. PES/Al2O3 membranes displayed superior antifouling properties and rejection values, keeping high the TPC (>95%). Therefore, UF using modified membranes is an appropriate and sustainable technique for treating TOPW.