Removal of AV 90 dye using ordered mesoporous carbon materials prepared via nanocasting of KIT-6: Adsorption isotherms, kinetics and thermodynamic analysis

Investigation of adsorption potential of acid violet 90 dye with chitosan/halloysite/boron nitride composite materials

In this study, composite adsorbents consisting of a mixture of chitosan (CTS), boron nitride (h-BN) and halloysite (HNT) were used for the adsorption of Acid Violet 90 (AV90) dye in a batch system. Adsorbents CTS, CTS/HNT, CTS/h-BN and CTS/h-BN/HNT beads were prepared by simple dropping method and dried in a freeze dryer. The beads were characterized by FT-IR, SEM and zeta potential analysis. The effects of pH (2-8) and dye concentration (50-250 mg/L) on AV90 adsorption properties of beads were investigated. In addition, Langmuir, Freunlich, Temkin and Henry adsorption isotherm models were used to examine the dye adsorption mechanism. It was observed that the Langmuir and Freundlich adsorption isotherm models were in good agreement with the experimental data. In the dye concentration range studied, the qm values of CTS, CTS/h-BN1, CTS/h-BN3, CTS/HNT/h-BN1, CTS/HNT/h-BN3, CTS/HNT obtained from the Langmuir isotherm model was 27.62, 17.80, 10.11, 8.71, 32.57, 19.96 mg/g, respectively. Pseudo-first order, pseudo-second order and intra-particle diffusion kinetic models were used to examine the adsorption kinetics of adsorbents. As a result, it is thought that the use of this study in the field of dye adsorption can be an innovative and important study.

Adsorptive removal of Safranine T dye from aqueous solutions using sodium alginate-Festuca arundinacea seeds bio-composite microbeads

In this study, composite microbeads were prepared using Festuca arundinacea seeds and sodium alginate biopolymer at different ratios and utilized as sorbents for the sorption of Safranine T from wastewater. The sorbents were characterized by FTIR, SEM, XRD, and BET analysis. According to BET analysis, the specific surface area of the adsorbents was calculated to be 10.99 m2/g and the surface was found to be mesoporous. The optimum conditions for adsorption studies including initial pH (2-12), concentration (10-50 mg/L), contact time (0-150 min), and adsorbent mass (0.05 g/50 mL-0.25 g/50 mL) were determined at 25 °C. The raw data obtained from sorption tests were applied to Freundlich, Langmuir-1, Langmuir-2, Langmuir-3, Langmuir-4, Temkin, Toth, and Koble-Corrigan isotherm models. The best results were obtained from the Langmuir-2 and accordingly the qm values were calculated as 454.54, 833.33, and 625.00 mg/g for FA, FA-SA-20, and FA-SA-30 at 25 °C, respectively. Adsorption kinetic data illustrated that the process followed the PSO model. Reusability and desorption studies were performed for composite microbeads. Additionally, the thermodynamic studies were performed at 25, 35 and 45 °C. Considering all these results, it was seen that the FA-SA-20 composite had the highest adsorption capacity and the best desorption efficiency.

Synthesis of Mesoporous Carbon Adsorbents Using Biowaste Crude Glycerol as a Carbon Source via a Hard Template Method for Efficient CO2 Capture

Biowaste utilization as a carbon source and its transformation into porous carbons have been of great interest to promote environmental remediation owing to biowaste's cost-effectiveness and useful physicochemical properties. In this work, crude glycerol (CG) residue from waste cooking oil transesterification was employed to fabricate mesoporous crude glycerol-based porous carbons (mCGPCs) using mesoporous silica (KIT-6) as a template. The obtained mCGPCs were characterized and compared to commercial activated carbon (AC) and CMK-8, a carbon material prepared using sucrose. The study aimed to evaluate the potential of mCGPC as a CO₂ adsorbent and demonstrated its superior adsorption capacity compared to AC and comparable to CMK-8. The X-ray diffraction (XRD) and Raman results clearly depicted the structure of carbon nature with (002) and (100) planes and defect (D) and graphitic (G) bands, respectively. The specific surface area, pore volume, and pore diameter values confirmed the mesoporosity of mCGPC materials. The transmission electron microscopy (TEM) images also clearly revealed the porous nature with the ordered mesopore structure. The mCGPCs, CMK-8, and AC materials were used as CO₂ adsorbents under optimized conditions. The mCGPC adsorption capacity (1.045 mmol/g) is superior to that of AC (0.689 mmol/g) and still comparable to that of CMK-8 (1.8 mmol/g). The thermodynamic analyses of the adsorption phenomena are also carried out. This work demonstrates the successful synthesis of a mesoporous carbon material using a biowaste (CG) and its application as a CO₂ adsorbent.

Research Progress on Porous Carbon-Based Non-Precious Metal Electrocatalysts

The development of efficient, stable, and economic electrocatalysts are key to the large-scale application of electrochemical energy conversion. Porous carbon-based non-precious metal electrocatalysts are considered to be the most promising materials to replace Pt-based catalysts, which are limited in large-scale applications due to high costs. Because of its high specific surface area and easily regulated structure, a porous carbon matrix is conducive to the dispersion of active sites and mass transfer, showing great potential in electrocatalysis. This review will focus on porous carbon-based non-precious metal electrocatalysts and summarize their new progress, focusing on the synthesis and design of porous carbon matrix, metal-free carbon-based catalysts, non-previous metal monatomic carbon-based catalyst, and non-precious metal nanoparticle carbon-based catalysts. In addition, current challenges and future trends will be discussed for better development of porous carbon-based non-precious metal electrocatalysts.

Regeneration of methylene blue-saturated biochar by synergistic effect of H2O2 desorption and peroxymonosulfate degradation

Biochar, as an adsorbent, is widely used for the removal of organic pollutants in water body. Hence, after saturated adsorption, regeneration treatment is required to recover the adsorption performance of biochar. In this study, a biochar (P-GBC) prepared by phosphoric acid activation showed high adsorption capacity for methylene blue (MB) with the maximum adsorption capacity (Q_m) of 599.66 mg/g. Then, regeneration treatments using 4 mM peroxymonosulfate (PMS), 0.2 M hydrogen peroxide (H₂O₂) and their mixture were used to regenerate MB-saturated biochar with regeneration efficiencies of 58.24%, 66.01% and 94.88%, respectively. Combining with degradation and quenching experiments, it is found that synergistic effect of H₂O₂ desorption and PMS degradation is responsible for the enhancement of regeneration efficiency of P-GBC in H₂O₂-PMS system and enables a high mineralization rate of 82.68% for the MB adsorbed on P-GBC. Furthermore, EPR tests indicate that singlet oxygen (¹O₂) is assigned as the primary activate species for the degradation of MB and XPS analyses confirm that graphite nitrogen and carbonyl on P-GBC are the main active sites for the activation of PMS. Compared with conventional regenerants, H₂O₂-PMS system has the advantages of low dosage, high mineralization efficiency, and easy accessibility, and is also effective, sustainable and environmentally friendly for the regeneration of organic pollutants-saturated biochar.

Magnetic Luffa-Leaf-Derived Hierarchical Porous Biochar for Efficient Removal of Rhodamine B and Tetracycline Hydrochloride

Luffa leaf (LL) is an agricultural waste produced by loofah. In this work, LL was used as biomass carbon source for biochars for the first time. After carbonization, activation, and chemical co-precipitation treatments, a magnetic lignocellulose-derived hierarchical porous biochar was obtained. The specific surface area and total pore volume were 2565.4 m²/g and 1.4643 cm³/g, and the surface was rich in carbon and oxygen functional groups. The synthetic dye rhodamine B (RhB) and the antibiotic tetracycline hydrochloride (TH) were selected as organic pollutant models to explore the ability to remove organic pollutants, and the results showed good adsorption performances. The maximum adsorption capacities were 1701.7 mg/g for RhB and 1755.9 mg/g for TH, which were higher than most carbon-based adsorbents. After 10 cycles of use, the removal efficiencies were still maintained at more than 70%, showing good stability. This work not only verified the feasibility of lignocellulose LL as a carbon source to prepare biochar but also prepared a magnetic hierarchical porous adsorbent with good performances that can better treat RhB and TH, which provided a new idea and direction for the efficient removal of organic pollutants in water.

Synthesis of mesoporous-structured MIL-68(Al)/MCM-41-NH2 for methyl orange adsorption: Optimization and Selectivity

Here, we report a novel amino-modified mesoporous-structured aluminum-based metal-organic framework adsorbent, MIL-68(Al)/MCM-41-NH₂, for dye sewage treatment. The introduction of molecular sieves overcomes the inherent defects of microporous MOFs in contaminant transfer and provides more active sites to enhance adsorption efficiency. Compared with using organic amino ligands directly, this strategy is ten times cheaper. The composite was well characterized and analyzed in terms of morphology, structure and chemical composition. Batch experiments were carried out to study the influences of essential factors on the process, such as pH and temperature. In addition, their interactions and the optimum conditions were examined using response surface methodology (RSM). The adsorption kinetics, isotherms and thermodynamics were systematically elucidated. In detail, the adsorption process conforms to pseudo-second-order kinetics and follows the Sips and Freundlich isothermal models. Moreover, the maximum adsorption capacity Q_s of methyl orange (MO) was 477 mg g^-1. It could be concluded that the process was spontaneous, exothermic, and entropy-reducing. Several binary dye systems have been designed for selective adsorption research. Our material has an affinity for anionic pigments. The adsorption mechanisms were discussed in depth. The electrostatic interaction might be the dominant effect. Meanwhile, hydrogen bonding, π-π stacking, and pore filling might be important driving forces. The excellent thermal stability and recyclability of the adsorbent are readily noticed. After five reuse cycles, the composite still possesses a removal efficiency of 90% for MO. Overall, the efficient and low-cost composite can be regarded as a promising adsorbent for the selective adsorption of anionic dyes from wastewater.

Olive mill wastewater from a liquid biological waste to a carbon/oxocalcium composite for selective and efficient removal of methylene blue and paracetamol from aqueous solution

In this study, a Carbon/Oxocalcium was prepared from olive mill wastewater and successfully applied to the removal of paracetamol and methylene blue (MB) from an aqueous medium. The optimized composite (0.3 % CaO) is rich in anionic sites, porous and has a specific surface area of about 1383 m².g^-1. Adsorption tests showed significant adsorption capacities up to 1141 mg.g^-1. The adsorption of MB and paracetamol is well described by the Redlich-Peterson and Dubinin-Radushkevich isotherm, respectively. Moreover, the adsorption kinetics fitted to pseudo-second order. The π -π interactions, hydrogen bonds and electrostatic interactions were responsible for the adsorption of paracetamol and MB substrates. This work develops by a single, easy and simple action a new effective and selective material for the removal of emerging pollutants, a new method for the development of more stable carbon composites and a cost-effective method for the valorization of olive mill wastewater.

Influence of Microbial Treatment on the Preparation of Porous Biochar with Stepped-Up Performance and Its Application in Organic Pollutants Control

In this study, Irisensata Thunb grass (ITG) was used as a biomass carbon resource to prepare biochars for the first time. After microbial treatment, the obtained microbial-treated ITG (MITG) was activated by using a mixed base as an activator for preparation of biochar (MITGB). The specific surface area and total pore volume of MITGB were 3036.4 m²/g and 1.5252 cm³/g, which were higher than those of biochar prepared without microbial treatment (ITGB, 2930.0 m²/g and 1.5062 cm³/g). Besides, the physicochemical properties of MITGB and ITGB were also quite different including micro morphology, surface chemistry, functional groups, etc. In the experiment of removing organic pollutants with synthetic dye RhB and antibiotic TH as the models, MITGB showed excellent treatment ability. The maximum adsorption capacities of MITGB for RhB and TH were 1354.2 and 1462.6 mg/g, which were higher than most of the biochars. In addition, after five cycles of recycling, the adsorption capacities of the organic pollutant models can still be maintained at more than 80%, which showed high stability. This work verified the feasibility of microbial treatment to further improve the performance of biochar and provided a new idea and direction for exploring other biochars.

Synthesis of novel epichlorohydrin cross-linked β-cyclodextrin functionalized with reduced graphene oxide composite adsorbent for treatment of phenolic wastewater

A novel composite consisting reduced graphene oxide-functionalized beta-cyclodextrin epichlorohydrin polymer (RGO-βCD-ECH) was synthesized for the treatment of phenolic wastewater. Batch study of phenolic pollutants (2,4-dichlorophenol, 2-chlorophenol, and phenol) was analyzed using the synthesized composite as an adsorbent from an aqueous solution. The optimized parameters were temperature 25 °C, adsorption time 60 min, solution pH 7, and dosage 0.25 g/L. The isotherm data were more suitably fitted by the Langmuir isotherm model. The maximum uptake for 2,4-dichlorophenol, phenol, and 2-chlorophenol was 702.853, 659.475, and 674.155 mg/g, respectively, at 25 ± 1 °C. The kinetic data for all the phenolic pollutants follow the pseudo-second-order model, and the rate was controlled by film diffusion. Thermodynamic data revealed that the process of removing phenolic pollutants is spontaneous and endothermic. The composite can be used up to five cycles with a small reduction in the removal. Adsorption performance of the synthesized composite for synthetic industrial effluents shows that up to 78% removal occurred in 60 min adsorption time. Based on the remarkably rapid adsorption and high adsorption capacity, the synthesized composite can be considered an efficient adsorbent for treating phenolic pollutants from wastewater.

Adsorption separation of guanosine 5'-Monophosphate and cytidine 5'-Monophosphate by mixed-mode Resin HD-1: Experimental study and mathematical modeling

The preparative separation of guanosine 5'-monophosphate (GMP) and cytidine 5'-monophosphate (CMP) on mixed-mode resin HD-1 was experimentally and theoretically investigated. The adsorption mechanisms of the two nucleotides were elucidated by analyzing adsorption equilibria and kinetics at different pH values. The adsorption dynamics of GMP and CMP in a fixed bed packed with resin HD-1 were studied. All nucleotide monovalent cations, zwitterions, and monovalent anions were adsorbed by the resin. Further, a general adsorption isotherm model was developed by considering the adsorption of different nucleotide species and the dissociation equilibrium behaviors of resin ligands. The model fit the adsorption isotherm data of GMP and CMP well. A modified liquid-film linear driving force model with the combined physical adsorption of nucleotides in different dissociation states and ion exchange of Na⁺ was established. The dissociation equilibria of resin ligands and nucleotides were considered. The model satisfactorily predicted the adsorption kinetic data at different pH values. The values of the efficient diffusion coefficients for GMP and CMP were not significantly influenced by the solution pH. A modified transport-diffusion model with pH gradient elution was proposed. The model accurately predicted the elution chromatographic peaks of GMP and CMP, as well as the pH at the outlet of the fixed bed packed with resin HD-1.

The Adsorptive Removal of Bengal Rose by Artichoke Leaves: Optimization by Full Factorials Design

Currently, the dye industry is increasing its production as a consequence of the growing need for their products in different manufacturing sectors, such as textiles, plastics, food, paper, etc... Thereafter, these industries generate very large volumes of effluents contaminated by these dyes, which require proper removal treatment before final discharge of the effluents into the environment. In this study, artichoke leaves were used as an economical and eco-friendly bio-adsorbent for Bengal Rose (BR) dye removal. Bio-adsorbent obtained from artichoke leaves was ground to powder size. The resulting powder was characterized by different methods, such as Brunauer-Emmett-Teller (BET) surface area analysis, scanning electron microscopy(SEM), X-ray Diffraction (XRD), Fourier transfer infrared (FTIR), pH at point of zero charge (pHpzc), equilibrium pH, iodine number, methylene blue number, phenol number, density, Energy dispersive X-ray spectroscopy (EDX) and Thermo-gravimetric analysis (TGA). Thereafter, the bio-adsorbent was used to study its capability for removing BR dye by testing contact time, initial concentration of dye and temperature. The results show that the saturation of bio-sorbent was reached after 40 min and the removal rate of BR dye by artichoke leaves powder (ALP) was 4.07 mg/g, which corresponds to a removal efficiency of 80.1%. A design of experiences (DOE) based on a two-level full factorial design (23) was used to study the effects of different parameters, such as pH, temperature and bio-adsorbent dosage on BR dye removal efficiency. The obtained results show that the highest removal efficiency was 86.5% for the optimized values of pH (4), temperature (80 °C) and bio-adsorbent dosage (8 g/L). Furthermore, a satisfying accordance between experimental and predicted data was observed. The kinetic and isotherm studies show that the pseudo-second order model simulated adequately the obtained data and it was found that Langmuir and Temkin isotherm models are liable and suitable for evaluating the adsorption process performance. Free energy change of adsorption (ΔG°), enthalpy change (ΔH°) and entropy change (ΔS°) were furthermore calculated to predict the nature of the adsorption process.

Recent Review of Titania-Clay-Based Composites Emerging as Advanced Adsorbents and Photocatalysts for Degradation of Dyes over the Last Decade

Textile industry being one of the most flourishing industries keeps growing and developing every year, and the consequences are not very pleasant. Even though its contribution towards economy of a country is indisputable, there are many pros and cons associated with it that should not be brushed aside, one of them being textile dye waste which is also growing at alarming rate. Many techniques have been designed to deal with this environmental crisis including adsorption and photodegradation of dye waste by various substances, both natural and synthetic. TiO2 and clay both have gained immense popularity in this area. Over the last decade, many successful attempts have been made to design TiO2-clay-based composites to combine and make the most of their individual capabilities to degrade textile dye waste. While clay is an effective adsorbent, inexpensive, innocuous, and a great ion exchanger, TiO2 provides supplementary active sites and free radicals and speeds up the degradation rate of dyes. This review summarizes various features of TiO2-clay-based composites including their surface characteristics, their role as dye adsorbents and photocatalysts, challenges in their implementation, and modifications to overcome these challenges made over the last decade.

Carboxylate-functionalized dragon fruit peel powder as an effective adsorbent for the removal of Rhodamine B (cationic dye) from aqueous solution: adsorption behavior and mechanism

In this study, we used a simple and low-toxicity chemical treatment to make a carboxylate-functionalized dragon fruit peel powder (CF-DFPP) from dragon fruit peel to improve its capacity for adsorbing Rhodamine B (RhB) from an aqueous medium. Field Emission-Scanning Electron Microscopy/Energy-Dispersive X-ray (FE-SEM/EDX), point of zero charges (pH_PZC), Brunauer-Emmett-Teller (BET), and Fourier Transform Infrared (FT-IR) analyses were performed to characterize the adsorbent materials. The adsorption performance and mechanism for the removal of RhB were examined. The kinetic, isotherm and thermodynamic parameters were employed to evaluate the adsorption mechanism. Compared to other models, the Langmuir isotherm and PSO kinetic models better defined the experimental data. CF-DFPP adsorbent exhibited a maximum adsorption efficiency of 228.7 mg/g at 298 K for RhB adsorption. Thermodynamic analysis revealed that the adsorption of RhB by CF-DFPP was spontaneous (ΔG^o < 0) and exothermic (ΔH^o < 0) nature of the process. Different eluting agents were used in desorption tests, and NaOH was revealed to have greater desorption efficiency (96.8%). Furthermore, regeneration examinations revealed that the biosorbent could effectively retain RhB, even after six adsorption/desorption cycles. These findings demonstrated that the CF-DFPP might be a novel material for removing RhB from an aqueous medium.

Preparation of Amino-Functionalized Mesoporous SBA-15 Nanoparticles and the Improved Adsorption of Tannic Acid in Wastewater

Ordered mesoporous Santa Barbara amorphous (SBA-15) materials have high surface areas and are widely used in adsorption, separation, filtration, and heterogeneous catalytic processes. However, SBA-15 surfaces contain hydroxyl groups that are unsuited to the adsorption of organic pollutants; thus, SBA-15 must be chemically modified to promote its adsorption activity. In this study, amino-functionalized nanoporous SBA-15 was fabricated by employing sodium silicate as a precursor. The structural characteristics of the prepared composites were examined using thermogravimetric analysis, X-ray diffraction, Fourier transform infrared spectrometry, field-emission scanning electron microscopy, transmission electron microscopy, and surface area analysis. The prepared SBA-15 had a large pore size (6.46–7.60 nm), large pore volume (1.037–1.105 cm³/g), and high surface area (546–766 m²/g). Functionalization caused a reduction in the SBA-15 pore volume and surface area, whereas amino groups that promoted an interaction between adsorbates and solids facilitated solute adsorption. The adsorption of tannic acid (TA) onto amino-modified silica composites (SBA-15 and 3-aminopropyltriethoxysilane (SBA-15/APTES) and SBA-15 and pentaethylenehexamine (SBA-15/PEHA)) was studied. Their adsorption capacities were affected by solution temperature, solution pH, agitation speed, adsorbent dosage, and initial TA concentration. The maximum adsorption capacities for SBA-15/APTES and SBA-15/PEHA were 485.18 and 413.33 mg/g, respectively, with SBA-15/APTES exhibiting ultrafast removal of TA (98.61% removal rate at 15 min). In addition, this study explored the thermodynamics, adsorption isotherms, and kinetics. A comparison of two types of amino-functionalized SBA-15 was used for the first time to adsorb TA, which providing valuable information on TA adsorption on high adsorption capacity materials in water media.

Immobilization of Trametes versicolor laccase on chitosan/halloysite as a biocatalyst in the Remazol Red RR dye

In this study, the laccase obtained from Trametes versicolor was immobilized onto the chitosan(CTS)/halloysite (HNT) beads. In the immobilization step, the effects of chitosan (1-3% w/v), halloysite (0-2% w/v), glutaraldehyde (0.5-1.5% v/v) and enzyme concentrations (1-3%) on loading and immobilization efficiency were investigated. SEM, FT-IR, XRD, TGA and XPS analyses were performed to examine the structure of beads. In addition, the effects of parameters such as pH (4-10), temperature (25-55 °C), storage life on the activity of free and immobilized laccase were also investigated. The activities of free and immobilized laccase preserved 23% and 56% of its initial activity at the end of 59 days of storage. The effects of mediators such as 2.2-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid (ABTS), 1-Hydroxybenzotriazole hydrate (HBT), 2,2,6,6-Tetramethyl-1-piperidinyloxy (TEMPO) and violuric acid (VLA) on the dye removal efficiency were investigated. Reusability of the CTS/HNT/Lac in the presence of HBT and VLA mediators, which enable the highest dye removal, was tested. After 15 cycles, 42% and 54% dye removal were achieved with the CTS/HNT/Lac in the medium containing HBT and VLA, and 42% and 49% of the activity is preserved, respectively. This study showed that CTS/HNT/Lac can be used repeatedly for Remazol Red RR dye removal.

The efficient removal of bisphenol A from aqueous solution using an assembled nanocomposite of zero-valent iron nanoparticles/graphene oxide/copper: Adsorption isotherms, kinetic, and thermodynamic studies

In this study, nanoparticles of zero-valent iron (nZVI) along with graphene oxide (GO) and copper (Cu) was synthesized to apply as a promising adsorbent for the rapid removal of bisphenol A (BPA) from aqueous solution. The characteristics of nZVI-GO-Cu were analyzed by field emission scanning electron microscope (FESEM), energy-dispersive X-ray spectroscopy (EDS), Fourier-transform infrared spectroscopy (FTIR), X-Ray Diffraction (XRD), and vibrating sample magnetometer (VSM). The average particle size of nZVI-GO-Cu was found to be 20.89 nm. The effective experimental variables such as pH, adsorbent dosage, contact time, initial BPA concentration, and temperature were surveyed to assess optimum conditions. Results revealed that the maximum removal percentage was obtained at pH of 7, adsorbent dosage of 0.2 g, contact time of 10 min, the BPA concentration of 10 mg/L, and a temperature of 35 °C as optimum conditions. Experimental data were fitted to the Langmuir and pseudo second-order models with a coefficient of determination (R²) equal to 1 and 0.995, respectively. The obtained maximum adsorption capacity (q_max) of the Langmuir isotherm was 21.59 mg g^-1. Thermodynamic parameters under the various temperatures confirmed that the adsorption process was endothermic (ΔH = 17,459.4 J/mol and ΔS = 61.23 J/mol/K) and spontaneous (ΔG < 0). As a conclusion, nZVI-GO-Cu can be selected as an efficient adsorbent for the treatment of aqueous media from BPA and the other pollutants, due to its low-cost, high removal efficiency (97%), and rapid adsorption with the minimum time of 10 min compared with the other adsorbents.

Preparation of clinoptilolite/starch/CoFe2O4 magnetic nanocomposite powder and its elimination properties for cationic dyes from water and wastewater

A new magnetic nanocomposite clinoptilolite (CLT)/Starch/CoFe₂O₄ was synthesized using co-precipitation method. The prepared magnetic composite powder was utilized for decontamination of methylene blue dye (MBD), methyl violet dye (MVD), and crystal violet dye (CVD) from water media. The BET analysis showed that CLT modification using starch and CoFe₂O₄ nanoparticles improved its specific surface and the amount of specific surface area for CLT, CoFe₂O_4, and CLT/Starch/CoFe₂O₄ powder was reported to be 18.82 m².g^-1, 151.4 m².g^-1, and 104.75 m².g^-1, respectively. Experimental results showed that pH 9 had a vital role in the adsorption process of all three types. Langmuir and Redlich-Petersen isotherm models were well fitted with experimental data. Also, the maximum adsorption capacity of CVD, MBD, and MVD to the desired composite was determined as 32.84 mg.g^-1, 31.81 mg.g^-1, and 31.15 mg.g^-1, respectively. In addition, the kinetic data of the removal process followed a pseudo-first order (PFO) kinetic model. Negative thermodynamic parameters were indicated that the process is spontaneous and exothermic. Finally, ad(de)sorption experiments' results showed that the synthesized nanocomposite adsorbent has an excellent ability to adsorb cationic dyes after several consecutive cycles.

Mesoporous Carbon: A Versatile Material for Scientific Applications

Mesoporous carbon is a promising material having multiple applications. It can act as a catalytic support and can be used in energy storage devices. Moreover, mesoporous carbon controls body’s oral drug delivery system and adsorb poisonous metal from water and various other molecules from an aqueous solution. The accuracy and improved activity of the carbon materials depend on some parameters. The recent breakthrough in the synthesis of mesoporous carbon, with high surface area, large pore-volume, and good thermostability, improves its activity manifold in performing functions. Considering the promising application of mesoporous carbon, it should be broadly illustrated in the literature. This review summarizes the potential application of mesoporous carbon in many scientific disciplines. Moreover, the outlook for further improvement of mesoporous carbon has been demonstrated in detail. Hopefully, it would act as a reference guidebook for researchers about the putative application of mesoporous carbon in multidimensional fields.

Mesoporous Carbons of Well-Organized Structure in the Removal of Dyes from Aqueous Solutions

Mesoporous carbons with differentiated properties were synthesized by using the method of impregnation of mesoporous well-organized silicas. The obtained carbonaceous materials and microporous activated carbon were investigated by applying different methods in order to determine their structural, surface and adsorption properties towards selected dyes from aqueous solutions. In order to verify applicability of adsorbents for removing dyes the equilibrium and kinetic experimental data were measured and analyzed by applying various equations and models. The structural and acid-base properties of the investigated carbons were evaluated by Small-Angle X-ray Scattering (SAXS) technique, adsorption/desorption of nitrogen, potentiometric titration, and Transmission Electron Microscopy (TEM). The results of these techniques are complementary, indicating the type of porosity and structural ordering, e.g., the pore sizes determined from the SAXS data are in good agreement with those obtained from nitrogen sorption data. The SAXS and TEM data confirm the regularity of mesoporous carbon structure. The adsorption experiment, especially kinetic measurements, reveals the utility of mesoporous carbons in dye removing, taking into account not only the adsorption uptake but also the adsorption rate.

Removal of anionic (Acid Yellow 17 and Amaranth) dyes using aminated avocado (Persea americana) seed powder: adsorption/desorption, kinetics, isotherms, thermodynamics, and recycling studies

Aminated avocado seed powder (AASP)-an eco-friendly novel adsorbent has been used for the removal of Acid Yellow 17 (AY 17) and Amaranth (AMR) from an aqueous phase. The AASP (before and after adsorption) was systematically characterized by different analytical techniques such as FT-IR, FESEM, EDX, and N₂ adsorption-desorption analysis. Non-linear form of various kinetic (PFO and PSO) and isotherm (Langmuir and Freundlich) models were used to examine the adsorption behavior of AY 17 and AMR onto AASP. The adsorption of AY 17 and AMR onto AASP was well illustrated by the PSO kinetic model and Langmuir isotherm models. At 303 K, the maximum adsorption capacities (obtained from the Langmuir) of the AASP for AY 17 and AMR was 42.7 and 89.2 mg/g, respectively. The AY 17 and AMR adsorption was strongly pH-dependent with an optimum pH value of 2.0. Activation energy was calculated as 12.3 and 16.3 kJ/mol for AY 17 and AMR respectively, suggesting physical adsorption. The positive values of ΔG^o and ΔH^o indicated that the adsorption process of AY 17 and AMR onto AASP was non-spontaneous and endothermic. The negligible loss of adsorption capacity and excellent regeneration of AASP were observed for the five cycles. Statement of novelty: The present research majorly focused on the synthesis of adsorbent from Avocado seed for the removal of Acid Yellow 17 and Amaranth anionic dyes from aqueous solution. Although the literature is available on direct seed powder as adsorbent, to the best of our knowledge, no chemical modified adsorbent synthesis was not available. Hence, to fill the gap in the literature, we chose the following study that significantly enhanced the adsorption efficiency of the selected anionic dyes.