Calcium alginate and barium alginate hydrogel filtration membrane coated on fibers for molecule/ion separation

Carrageenan/calcium alginate composite hydrogel filtration membranes for efficient cationic dye separation

The development of biopolymer-based filtration systems for water remediation applications is an extremely fascinating area of research. In this paper, we developed a biopolymer-based filtration system using sodium alginate (NaAlg) and carrageenan (Car) for the removal of the toxic cationic dye, methylene blue (MB). The membrane's properties were assessed using FTIR, TGA, UTM, FESEM, EDS, XRD, and water uptake, revealing commendable thermomechanical stability (5.79 MPa), good hydrophilicity, and compatibility. The experimental results further revealed that lambda Car/calcium alginate (λ-Car/CaAlg) exhibited superior dye rejection (100%) and flux (11.67 L m-2 h-1) compared to kappa Car/CaAlg (κ-Car/CaAlg) (99.22% and 11.19 L m-2 h-1) and plain alginate (CaAlg) (99.63% and 9.79 L m-2 h-1). The high MB rejection rate was attributed to the sieving mechanism and electrostatic interaction. A rejection rate of 100% was achieved at an initial MB concentration of 10 mg/L, pressure of 0.1 MPa, pH of 7, and temperature of 25°C. Furthermore, the hydrogel membranes demonstrated excellent recyclability over nine cycles, indicating their potential for water treatment applications.

An eco-friendly hydroentangled cotton non-woven membrane with alginate hydrogel for water filtration

Alginate hydrogel is highly efficient for water filtration due to its anti-fouling nature and formation of strong hydration membranes. However, poor mechanical properties of alginate hydrogel membrane limit its installation in water treatment. There is a need to enhance mechanical properties of alginate hydrogel membranes using eco-friendly, cost-effective materials and technologies. In this work, hydroentangled non-woven from cotton waste (comber noil) fibers was prepared. This non-woven was immersed in solution of sodium alginate (0.5 %, 1 %, 1.5 %) followed by dipping in calcium chloride solution which resulted in gel formation on and into cotton fibers. The successful formation of gel on non-woven fabric was confirmed through FTIR (Fourier transform infrared spectroscopy) and properties of this composite membrane were analyzed by SEM (Scanning electron microscopy), XRD (X-ray diffraction), DSC (Differential scanning calorimeter), water contact, water flux, oil-water filtration, air permeability, tensile strength, and porosity tests. The results showed that porosity of prepared hydrogel membranes decreased with increasing alginate concentration from 0.5 % to 1.5 % which resulted in decreased water permeation flux from 2655 h-1/m2 to 475 h-1/m2. The prepared membrane has separation efficiencies for the oil-water mixture in the range of 97.5 % to 99.5 %. Moreover, the developed samples also showed significant antibacterial activity as well as improved mechanical properties. The strength of the prepared membrane is in the range of 40 N to 80 N. The developed sodium alginate hydrogel-based non-woven membrane could have potential applications for commercial water filtration systems.

Recent advances in cellulose- and alginate-based hydrogels for water and wastewater treatment: A review

From the environmental perspective, it is essential to develop cheap, eco-friendly, and highly efficient materials for water and wastewater treatment. In this regard, hydrogels and hydrogel-based composites have been widely employed to mitigate global water pollution as this methodology is simple and free from harmful by-products. Notably, alginate and cellulose, which are natural carbohydrate polymers, have gained great attention for their availability, price competitiveness, excellent biodegradability, biocompatibility, hydrophilicity, and superior physicochemical performance in water treatment. This review outlined the recent progress in developing and applying alginate- and cellulose-based hydrogels to remove various pollutants such as dyes, heavy metals, oils, pharmaceutical contaminants, and pesticides from wastewater streams. This review also highlighted the effects of various physical or chemical methods, such as crosslinking, grafting, the addition of fillers, nanoparticle incorporation, and polymer blending, on the physiochemical and adsorption properties of hydrogels. In addition, this review covered the alginate- and cellulose-based hydrogels' current limitations such as low mechanical performance and poor stability, while presenting strategies to improve the drawbacks of the hydrogels. Lastly, we discussed the prospects and future directions of alginate- and cellulose-based hydrogels. We hope this review provides valuable insights into the efficient preparations and applications of hydrogels.

Characterization of a chlorine resistant and hydrophilic TiO2/calcium alginate hydrogel filtration membrane used for protein purification maintaining protein structure

The development of membranes for protein purification has stringent requirement of disinfection resistance, low protein adsorption and anti-fouling, without changing protein structure. In this study, hydrophilic titanium dioxide (TiO2)/calcium alginate (TiO2/CaAlg) hydrogel membranes were prepared by a simple ionic cross-linking method. The effects of the porogenic agent polyethylene glycol (PEG) concentration, the molecular weight of PEG, and the concentration of TiO2 on the filtration properties were systematically investigated. The TiO2/CaAlg membrane exhibited excellent bovine serum albumin (BSA) rejection and anti-fouling properties. The mechanical properties and surface energy of the TiO2/CaAlg membrane were significantly improved. The chemical bonding mechanism of TiO2 and NaAlg was investigated by molecular dynamic simulation. The TiO2/CaAlg membrane had good chlorine resistance and could be disinfected or cleaned with sodium hypochlorite. The TiO2/CaAlg hydrogel membrane loaded with polyhydroxybutyrate (PHB) nanofibers maintained high flux (136.7 L/m2h) and high BSA rejection (98.0 %) at 0.1 MPa. The results of circular dichroism and synchronous fluorescence indicated that the secondary structure of BSA was maintained after membrane separation. This study provides one method for the preparation of green and environmentally friendly membrane for protein purification.

Stretchable and transparent alginate ionic gel film for multifunctional sensors and devices

Flexible and stretchable substrates based on pure natural polymers have attracted widespread attention for next-generation "green" electronics. However, fabrication of stretchable and "green" electronic sensors with integrated high stretchability, optical transmittance and good conductivity still remains tremendous challenges. Herein, alginate ionic gel films (AIGFs) with integrated high stretchability (tensile strength of 4.13 MPa and 191.1 % fracture strain) and excellent transparent properties (transparency of ∼92 %) are achieved by the glycerol inducing physical crosslinking and CaCl2 initiating ionic crosslinking, a simple soaking and drying strategy. The obtained gel films not only exhibit good ionic conductivity, but also high reliability, wide-range sensing, and multiple sensitivity to external stimulus. More importantly, these ionic conductive gel films as green substrates are successfully utilized for construction of flexible and patterned optoelectronic devices. This promising strategy will open up new powerful routes to construct highly stretchable, transparent, and ionic conductive substrates for multifunctional sensors and devices.

Triclocarban-contaminated wastewater treatment by innovative hybrid moving entrapped bead activated sludge reactor (HyMER): Continuous performance and computational dynamic simulation analysis

Triclocarban (TCC) has been used in consumer products and is a widespread contaminant in municipal wastewater treatment systems that ultimately accumulates in natural receiving water and soil. This work aims to apply an innovative hybrid moving entrapped bead activated sludge reactor (named "HyMER") that integrates entrapped TCC-degrading microbes and freely suspended activated sludge to treat TCC-contaminated wastewater. A previously isolated TCC-degrading bacterium (Pseudomonas fluorescens strain MC46, called MC46) and barium alginate entrapment were applied. The synthetic TCC-contaminated wastewater treatment (with TCC concentration of 10 mg/L) was performed using 20-cycle fed-batch reactor operation with feeding times of 12 and 24 h and cycle times of 13 and 25 h. The results indicated that the HyMER effectively reduced chemical oxygen demand by up to 80 and 95 % and TCC by up to 53 and 83 %, respectively, with feeding times of 12 and 24 h. Three TCC degradation intermediate products were found-3,4-dichloroaniline, 4-chloroaniline, and aniline. Scanning electron microscopic analysis revealed shorter cells and bacterial appendage development as cell adaptations against TCC and its intermediates. The live/dead assay indicated high survival of entrapped MC46 in toxic conditions, with up to 84 % viable cells. Based on computational fluid dynamic analysis, no entrapped cell agglomeration showed in the reactor, indicating the potential application of HyMER for real wastewater treatment. These results exhibit the feasibility of HyMER and its applicability for future toxic wastewater treatment.

A Pitaya-Inspired Modular Cylindrical MOF-Based Capsule Design for Pesticide Signal Probes

Excessive use of pesticides has brought about serious environmental risks worldwide that pose significant harm for human health. Herein, a series of metal-organic framework (MOF)-based gel capsules with a pitaya-like core-shell structure are constructed through a green polymerization strategy for pesticide detection and removal, namely ZIF-8/M-dbia/SA (M = Zn, Cd). Significantly, the ZIF-8/Zn-dbia/SA capsule exhibits sensitive detection of alachlor, a representative pre-emergence acetanilide pesticide, with a satisfactory detection limit of 0.23 μM. In addition, the MOF-based gel capsules can be extended to a universal visual platform for the noninvasive detection of pesticide residues with various MOFs, such as Eu-MOF, Tb-MOF, and Cu-MOF, and participating dye. Similar to pitaya, the ordered porous structure of MOF in ZIF-8/Zn-dbia/SA capsules offers cavity and open sites for removing pesticide from water with the maximum adsorption amount q_max of 61.1 mg·g^-1 toward alachlor in a Langmuir model. Thereby, this work presents the universality of gel capsule self-assembly technologies, including the well-preserved visible fluorescence area and porosity of the different structurally diverse MOFs, offering an ideal strategy for water decontamination and food safety control fields.

Surfactant-Free Emulsion of Epoxy Resin/Sodium Alginate for Achieving Robust Underwater Superoleophobic Coating via a Combination of Phase Separation and Biomineralization

Underwater superoleophobic coatings exhibit promising prospects in the field of oil contamination resistance. However, their poor durability, stemming from the fragile structures and unstable hydrophilicity, greatly restricted their development. In this report, we proposed a novel strategy of combination water-induced phase separation and biomineralization to prepare the robust underwater superoleophobic epoxy resin-calcium alginate (EP-CA) coating by utilizing a surfactant-free emulsion of epoxy resin/sodium alginate (EP/SA). The EP-CA coating not only exhibited excellent adhesion to various substrates, but also had remarkable resistance to the physical/chemical attacks such as abrasion, acid, alkali and salt. It could also protect the substrate (e.g., PET substrate) from the damage of organic solution and the fouling of crude oil. This report provides a new perspective to fabricate robust superhydrophilic coating with a facile way.

Calcium Alginate Production through Forward Osmosis with Reverse Solute Diffusion and Mechanism Analysis

Calcium alginate (Ca-Alg) is a novel target product for recovering alginate from aerobic granular sludge. A novel Ca-Alg production method was proposed herein where Ca-Alg was formed in a sodium alginate (SA) feed solution (FS) and concentrated via forward osmosis (FO) with Ca²⁺ reverse osmosis using a draw solution of CaCl₂. An abnormal reverse solute diffusion was observed, with the average reverse solute flux (RSF) decreasing with increasing CaCl₂ concentrations, while the average RSF increased with increasing alginate concentrations. The RSF of Ca²⁺ in FS decreased continuously as the FO progressed, using 1.0 g/L SA as the FS, while it increased initially and later decreased using 2.0 and 3.0 g/L SA as the FS. These results were attributed to the Ca-Alg recovery production (CARP) formed on the FO membrane surface on the feed side, and the percentage of Ca²⁺ in CARP to total Ca²⁺ reverse osmosis reached 36.28%. Scanning electron microscopy and energy dispersive spectroscopy also verified CARP existence and its Ca²⁺ content. The thin film composite FO membrane with a supporting polysulfone electrospinning nanofiber membrane layer showed high water flux and RSF of Ca²⁺, which was proposed as a novel FO membrane for Ca-Alg production via the FO process with Ca²⁺ reverse diffusion. Four mechanisms including molecular sieve role, electrification of colloids, osmotic pressure of ions in CARP, and FO membrane structure were proposed to control the Ca-Alg production. Thus, the results provide further insights into Ca-Alg production via FO along with Ca²⁺ reverse osmosis.

Peptide hydrogel based sponge patch for wound infection treatment

Dressing with the function of anti-wound infection and promoting skin repair plays an important role in medicine, beauty industry, etc. In terms of anti-wound infection, traditional dressings, such as gauze, have problems such as excessive bleeding in the process of contact or removal, and slow wound healing due to poor biological compatibility. The development of new functional and biocompatible dressings has essential application value in biomedical fields. In this study, a new type of dressing based on polypeptide functional sponge patch was constructed. The porous sponge patch is made of antimicrobial peptide and medical agarose through gel and freeze-drying technology. In vitro antibacterial experiments and small animal skin wound infection model experiments show that the porous sponge has excellent antibacterial and anti-skin infection activities, as well as the function of promoting wound healing.

High-strength and anti-bacterial BSA/carboxymethyl chitosan/silver nanoparticles/calcium alginate composite hydrogel membrane for efficient dye/salt separation

In order to solve the problems of poor mechanical property, non-antibacterial and low flux of calcium alginate (CaAlg) membrane, silver nanoparticles (AgNPs) were synthesized with bovine serum albumin (BSA) and carboxymethyl chitosan (CMCS) for improving CaAlg membrane in this paper. Meanwhile, the dispersion property of silver nanoparticles and the mechanical property, thermal stability, antibacterial property and filtration efficiency of the composite membrane were explored. The results illustrated CMCS observably strengthened the mechanical property and thermal stability of the composite membrane, and AgNPs endowed the composite membrane with excellent antibacterial property. The flux of the BSA/CMCS/AgNPs/CaAlg composite membrane was raised compared to CaAlg membrane. Finally, the viscose fiber/polyethylene terephthalate fiber (VF-PET) nonwoven fabric was introduced as the support layer to further improve the filtration flux and mechanical property of the composite membrane. VF-PET/BSA/CMCS/AgNPs/CaAlg membrane had a rejection rate of over 99.0 % for dye molecules and <9.0 % for salt ions, while the flux maintained 38.5 L·m^-2·h^-1. Furthermore, VF-PET/BSA/CMCS/AgNPs/CaAlg membrane also had excellent separation effect on actual dye wastewater. The separation of dye and salt by the membrane mainly depended on the screening mechanism of membrane pore size, rather than adsorption. The composite membrane had an outstanding performance on the separation of dye molecules and inorganic salt ions.

Application of polysaccharide-based metal organic framework membranes in separation science

Polysaccharide/MOF composite membranes have captured the interests of many researchers during decontamination of polluted environments. Their popularity can be attributed to the relatively high chemical and thermal stabilities of these composite membranes. Chitosan is among the polysaccharides extensively used during the synthesis of hybrid membranes with MOFs. The applications of chitosan/MOF composite membranes in separation science are explored in detail in this paper. Researchers have also synthesised mixed matrix membranes of MOFs with cellulose and cyclodextrin that have proved to be effective during separation of a variety of materials. The uses of cellulose/MOF and cyclodextrin/MOF membranes for the removal of environmental pollutants are discussed in this review. In addition, the challenges associated with the use of these mixed matrix membranes are explored in this current paper.