A bio-based 3D evaporator nanocomposite for highly efficient solar desalination

Enhancing Solar Steam Generation of Hydrogels via Silver Nanoparticle-Doped Cellulose Nanofibers

Solar steam generation (SSG) is regarded as an efficient approach for harnessing solar energy to purify polluted or saline water. Herein, we demonstrate a hydrogel composed of cellulose nanofibers (CNFs), polyethylenimine (PEI), and reduced graphene oxide (rGO) that functions as an independent solar steam generator, which shows enhanced solar water evaporation efficiency by incorporating silver nanoparticles (AgNPs). It presented that the presence of AgNPs increases the photothermal conversion efficiency and thermal conductivity of the evaporator and reduces the enthalpy of evaporation. As a result, an outstanding water evaporation rate of 3.62 kg m-2 h-1 and a photothermal conversion efficiency of 96.25% are successfully obtained under one sun illumination. Also, the resulting hydrogel exhibits exceptional mechanical properties, as well as outstanding desalination and salt-resistant abilities during prolonged seawater desalination. In oil/water mixtures, the evaporation of the hydrogel decreases to 2.94 kg m-2 h-1, owing to the oil layer barrier. This work paves a reference approach to produce easily addressed cellulose nanofiber (CNF)-based hydrogel evaporators with significantly enhanced evaporation rates.

Hanging Photothermal Fabric Based on Polyaniline/Carbon Nanotubes for Efficient Solar Water Evaporation

Solar-driven water evaporation is essential to provide sustainable and ecofriendly sources of fresh water. However, there are still great challenges in preparing materials with broadband light absorption for high photothermal efficiency as well as in designing devices with large evaporation areas and small heat dissipation areas to boost the water evaporation rate. We designed a hanging-mode solar evaporator based on the polyaniline/carbon nanotube (PANI/CNT) fabric, in which the photothermal fabric acts as the solar evaporator and the micropores on the cotton fabric act as the water transfer channels. The hanging mode provides efficient evaporation at both interfaces by greatly reducing the heat dissipation area. The hanging mode PANI/CNT fabric solar evaporator can achieve an evaporation rate of 2.81 kg·m-2·h-1 and a photothermal efficiency of 91.74% under a solar illumination of 1 kW·m-2. This high-performance evaporator is designed by regulating the photothermal material and evaporation device, which provides a novel strategy for sustainable desalination.

Scalable, Green, and Cost-Effective Carbonized Sand for Efficient Solar Desalination

Nowadays, sweet and drinkable water shortage is a global issue which has attracted widespread attention. Desalination of seawater as the greatest source of water on our planet using solar energy as the most abundant and green energy source for producing fresh water can help us address this issue. Interfacial solar desalination is a state-of-the-art, sustainable, green, and energy-efficient method that has been studied lately. One of the key parameters for researching this method with reasonable efficiency is a photothermal material. Herein, carbon-coated sand was synthesized using abundant, green, and low-cost materials (sand and sugar), and its performance as a photothermal material is investigated and reported. In this work, a three-dimensional (3D) system is introduced to develop the performance and efficiency of the system under real sun irradiation and natural circumstances. The salt rejection ability of the system is another important thing we should notice due to the high salinity of seawater that we want to desalinate. The superhydrophilic carbonized sand demonstrated a good evaporation rate of 1.53 kg/m²h and 82% efficiency under 1 sun irradiation and upright salt rejection ability, which exhibited its capability to be used in green solar-driven water vaporization technology for sweet water production. The effects of important parameters, including light intensity, wind speed, and environment temperature, on the evaporation rate using carbonized sand as a solar collector in a solar desalination system were studied in both laboratory and real systems.

Chitosan-supported metal nanocatalysts for the reduction of nitroaromatics

The second most abundant natural polymer in the earth's crust is chitosan (CS). The unique physical, chemical, structural, and mechanical features of this natural polymer have led to its increased application in a variety of fields such as medicine, catalysis, removal of pollutants, etc. To eliminate various pollutants, it is preferable to employ natural compounds as their use aids the removal of contaminants from the environment. Consequently, employing CS to eliminate contaminants is a viable choice. For this aim, CS can be applied as a template and support for metal nanoparticles (MNPs) and prevent the accumulation of MNPs as well as a reducing and stabilizing agent for the fabrication of MNPs. Among the pollutants present in nature, nitro compounds are an important and wide category of biological pollutants. 4-Nitrophenol (4-NP) is one of the nitro pollutants. There are different ways for the removal of 4-NP, but the best and most effective method for this purpose is the application of a metallic catalyst and a reducing agent. In this review, we report the recent developments regarding CS-supported metallic (nano)catalysts for the reduction of nitroaromatics such as nitrophenols, nitroaniline compounds, nitrobenzene, etc. in the presence of reducing agents. The metals investigated in this study include Ag, Au, Ni, Cu, Ru, Pt, Pd, etc.

Rapid Fabrication of Porous Photothermal Hydrogel Coating for Efficient Solar-Driven Water Purification

Cost management and scalable fabrication without sacrificing the purification performance are two critical issues that should be addressed before the practical commercial application of solar-driven evaporators. To address this challenge, we report a porous photothermal hydrogel coating prepared by mixing the raw materials of sawdust (SD), carbon nanotubes (CNTs), and poly(vinyl alcohol) (PVA), which was applied to undergo a blading-drying-rehydration process to prepare the evaporator. In the coating, the crystallized PVA gives the coating a solid skeleton and the sawdust endows the coating with a loose structure to sufficiently enhance the water transportation capacity. As a result, the evaporator coated with the hydrogel coating displays a high water transport rate and efficient evaporation performance along with excellent mechanical properties and stability. Water migrates vertically upward 5 cm within 4 minutes. The compressive stress of the rehydrated hydrogel coating reaches as high as 14.28 MPa under 80% strain. The water evaporation rate of the hydrogel coating-based evaporator reaches 1.833 kg m^-2 h^-1 corresponding to an energy efficiency of 83.29% under 1 sun irradiation. What is more, the hydrogel coating retains its excellent evaporation performance and stability after immersion in acid or alkali solution, ultrasound treatment, and long-time immersion in water. Under outdoor conditions, the water evaporation rate of the hydrogel coating-based evaporator is about 5.69 times higher than that of pure water. This study proposes a rapid, cost-effective, and scalable strategy for preparing a high-performance photothermal hydrogel coating that will find sustainable and practical application in solar-driven water purification.

Lignosulfonate valorization into a Cu-containing magnetically recyclable photocatalyst for treating wastewater pollutants in aqueous media

This study presents an eco-friendly and economical process for preparing a magnetic copper complex conjugated to modified calcium lignosulfonate (LS) through a diamine (Fe₃O₄@LS@naphthalene-1,5-diamine@copper complex; FLN-Cu) as a green and novel catalyst. The prepared catalyst was characterized by Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), vibrating sample magnetometer (VSM), Brunauer-Emmett-Teller (BET), energy-dispersive X-ray spectroscopy (EDS), elemental mapping, inductively coupled plasma-optical emission spectrometry (ICP-OES) and field emission scanning electron microscopy (FESEM) techniques. The photocatalytic performance of the synthesized FLN-Cu catalyst was investigated by the degradation of aqueous solutions of dyes such as Rhodamine B (RhB), methylene blue (MB), and Congo red (CR) under UV irradiation. The dye degradation was followed by UV-Vis (ultraviolet-visible) spectrophotometry by measuring the changes in absorbance. The effects of different factors such as pH, contact time, photocatalyst dosage, and initial concentration of dye on the adsorption percentage were also investigated. Moreover, the catalyst showed high stability and could be readily separated from the reaction media using a magnet and reused five times without a remarkable loss of catalytic ability.

Modified chitosan-zeolite supported Pd nanoparticles: A reusable catalyst for the synthesis of 5-substituted-1H-tetrazoles from aryl halides

A novel heterogeneous catalyst has been developed using chitosan-zeolite supported Pd nanoparticles (PdNPs@CS-Zeo) and used in an efficient synthesis of 5-substituted-1H-tetrazoles from aryl halides with high yields for relatively short reaction times with an easy work-up procedure. In this method, highly effective and reusable PdNPs@CS-Zeo catalyst was used in the reaction of various aryl iodides/bromides with K₄[Fe(CN)₆] as a non-toxic cyanide source to catalyze the [2 + 3] cycloaddition of the corresponding aryl nitriles with NaN₃ in the sequential one-pot preparation of 5-substituted-1H-tetrazoles. The synthesized PdNPs@CS-Zeo nanocatalyst was characterized using XRD, FTIR, TEM, HRTEM, XPS, Raman, TG-DTG, ICP-OES, BET, and EDS mapping. Additionally, the nanocatalyst could be effectively separated by filtration and reused for multiple times without significant decrease of catalytic activity.