A biomass resource strategy for alginate-polyvinyl alcohol double network hydrogels and their adsorption to heavy metals

Analysis of unsaturated alginate oligosaccharides using high-performance anion exchange chromatography coupled with mass spectrometry

Alginate is a commercially important polysaccharide composed of mannuronic acid and its C5 differential isomer guluronic acid. Comprehensive research on alginate and alginate lyases requires efficient and precise analytical methods for alginate oligosaccharides. In this research, high-performance anion exchange chromatography (HPAEC) in parallel with pulsed amperometric detection (PAD) and mass spectrometry (MS) was applied to the analysis of oligosaccharides obtained by alginate lyase. By optimizing the chromatographic conditions including mobile phase concentration, flow rate, and elution gradient, the analysis of a single sample could be completed in 30 min. Seven unsaturated alginate oligosaccharides were separated and identified through their analysis time observed with PAD, including all structurally different unsaturated disaccharides and trisaccharides. The quantitative analysis of seven oligosaccharides was performed based on the quantitative capability of PAD. The method exhibited adequate linearity and precision parameters. All the calibration curves showed good linearity at least in the concentration range of 0.002 to 0.1 mg/mL. The HPAEC-PAD/MS method provides a general and efficient online method to analyze alginate oligosaccharides.

Performance evaluation of facile synthesized CA-PVA-GO composite for the mitigation of Cr(Ⅲ) and C.I. acid violet 54 dye from tannery wastewater

Untreated tannery wastewater contains a large amount of toxic metals, dyes, and other pollutants, which pose adverse effects on the ecosystem and public health. In this work, a calcium alginate-poly vinyl alcohol-graphene oxide (CA-PVA-GO) composite was prepared to remove metals and dyes, particularly Cr(Ⅲ) and CI acid violet 54 (AV54) dye, from tannery wastewater. FESEM, FTIR, and XRD analyses were applied to characterize the GO and CA-PVA-GO. Different operational variables, viz. pH (3.0-5.5 for Cr(III) and 2-7 for dye), dosage (0.164-2.46 g/L), contact time (10-60 min), initial concentration (39, 65, 98, and 201 ppm for Cr(III) and 21.5, 38.5, 54.5, and 61.75 ppm for dye), and temperature (298, 308, 318, and 328 K) were studied to evaluate the efficiency of the CA-PVA-GO composite. The optimum conditions for Cr(Ⅲ) and AV54 dye adsorption were found to be pH (5.0 and 3.0), dosage (0.82 g/L for both), and time (45 and 60 min), respectively, with 35.35 ± 1.43% and 84.63 ± 2.54% removal efficiency. The experimental data was analyzed through the Langmuir and Freundlich isotherms. The maximum adsorption capacity (qm) was observed at 173.01 and 74.68 mg/g for Cr(Ⅲ) and AV54 dye, respectively. The pseudo-second-order kinetic model was fitted better (R2 = 0.981, 0.995, 0.92, and 0.995) than first-order for AV54 dye adsorption. Thermodynamic analyses revealed that the Cr(Ⅲ) and AV54 dye adsorption processes were spontaneous and exothermic. The value of Gibbs free energy (ΔG) for Cr(III) adsorption was obtained at -7.433, -4.508, -2.626, and -1.311 kJ/mol, whereas it was -5.178, -4.867, -4.628, and -4.555 kJ/mol for dye. The values of ΔH and ΔS were -67.257 and -0.198 kJ/mol for Cr(III) and -10.852 and -0.019 kJ/mol for the dye removal. The regenerated CA-PVA-GO composite was reused successfully. Different physicochemical parameters, viz., concentration, pH, TDS, EC, BOD5, and COD of chrome tanning and dyeing effluents, were analyzed before and after the adsorption. The results of chromium and dye removal from tannery wastewater were 53.18% and 93.91%, revealing that the developed eco-friendly CA-PVA-GO composite could be an operative adsorbent for tannery wastewater treatment and possibly scaled up to an industrial level.

Environmental applications of lignin-based hydrogels for Cu remediation in water and soil: adsorption mechanisms and passivation effects

Heavy metal pollution, particularly the excessive release of copper (Cu), is an urgent environmental concern. In this study, sodium lignosulfonate/carboxymethyl sa-son seed gum (SL-Cg-g-PAA) designed for remediation of Cu-contaminated water and soil was successfully synthesized through a free radical polymerization method using lignin as a raw material. This hydrogel exhibits remarkable Cu adsorption capability when applied to water, with a maximum adsorption capacity reaching 172.41 mg/g. Important adsorption mechanisms include surface complexation and electrostatic attraction between Cu(Ⅱ) and oxygen-containing functional groups (-OH, -COOH), as well as cation exchange involving -COONa and -SO3Na. Furthermore, SL/Cg-g-PAA effectively mitigated the bioavailability of heavy metals within soil matrices, as evidenced by a notable 14.1% reduction in DTPA extracted state Cu (DTPA-Cu) content in the S4 treatment (0.7% SL/Cg-g-PAA) compared to the control group. Concurrently, the Cu content in both the leaves and roots of pakchoi exhibited substantial decreases of 55.19% and 36.49%, respectively. These effects can be attributed to the precipitation and complexation reactions facilitated by the hydrogel. In summary, this composite hydrogel is highly promising for effective remediation of heavy metal pollution in water and soil, with a particular capability for the immobilization of Cu(Ⅱ) and reduction of its adverse effects on ecosystems.

Green preparation of magnetic ferroferric oxide-polyvinyl alcohol-alginate coated UiO-67 nanospheres: Characterization, adsorption properties and adsorption mechanism of methylene blue

In this paper, a kind of magnetic ferric oxide/polyvinyl alcohol/calcium alginate/UiO-67 (Fe3O4/PVA/CA/UiO-67) nanospheres with homogeneous surface interconnecting structures was prepared by using macromolecular polymer polyvinyl alcohol and sodium alginate as carriers and zirconium organic skeleton as nanocrystals. The properties of magnetic nanospheres were studied by SEM, FT-IR, TGA, XRD, BET, VSM and Zeta potential. The impression of diverse temperatures, MB concentrations, interaction time, pH, and magnetic aerogel sphere dose on MB removal was studied. The optimum adsorption temperature and pH of magnetic nanospheres for MB were 298 K, and 10, respectively. Langmuir simulated that the maximum removal of MB by magnetic nanospheres at room temperature (298 K) was 1371.8 mg/g. The removal of MB by magnetic nanospheres complied with the pseudo-first-order kinetic model. The isotherm simulation can infer that the Langmuir model was more comply with MB adsorption on magnetic aerogel spheres. Thermodynamic studies have confirmed that the removal of MB by magnetic nanospheres was exothermic and spontaneous. The interaction mechanism of MB on magnetic nanospheres can be deduced by FT-IR and BET, including hydrogen bond, π-π bond, electrostatic interaction, and mesoporous pore flow. The removal rate of nanospheres for MB still reached 70.06 % after six cycles.

Effect of the magnetic core in alginate/gum composite on adsorption of divalent copper, cadmium, and lead ions in the aqueous system

The change of composition of an adsorbent material has been widely used as a method to increase its adsorption capacity, particularly concerning adsorbents made of polysaccharides. Introducing magnetic adsorbents into contaminated water treatment systems is a highly promising strategy, as it promotes the metal ions removal from water. Considering this, gum Arabic (GA) was associated with alginate (Alg), when magnetite nanoparticles were present or absent, to produce beads that were utilised to take up Cu(II), Cd(II), and Pb(II) from aqueous solution. After a complete characterisation (for which Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, and swelling were used), the adsorption properties were established using batch and column tests. The magnetic beads (MAlg/GA) demonstrated improved adsorption in comparison with the beads made without magnetite (Alg/GA) under the same conditions. In normal adsorption conditions (pH 6.0, 25 °C, 2.5 g L-1 of adsorbent dosage), the highest uptake capacities recorded for the MAlg/GA beads were: for Cu(II), 1.33 mmol g-1; Cd(II), 1.59 mmol g-1; and for Pb(II), 1.43 mmol g-1. The pseudo-second-order kinetics and Langmuir isotherm models provided good fits for the adsorption of these metals. Overall, ion exchange and physical forces led to the uptake of these metals by both Alg/GA and MAlg/GA; moreover, the functional groups on the beads played crucial roles as binding sites. Additionally, it was observed that flow rates of >2 mL min-1 did not produce noticeable changes in uptake levels over the same flow period. It was found that the efficient eluting agent was HNO3 (0.2 M). In some cases, the metals were not removed fully from the used beads during the first five cycles of regeneration and reuse. The results of this investigation show that these beads are efficient adsorbents for the removal of metal ions from spiked well water samples.

Dual Benefits of Hydrogel Remediation of Cadmium-Contaminated Water or Soil and Promotion of Vegetable Growth under Cadmium Stress

This study aims to solve the problem of cadmium heavy metal ion pollution caused by the abuse of chemical fertilizers and activities such as mining, which pose a serious threat to the plant growth environment. We successfully synthesized DMAPAA (N-(3-(Dimethyl amino) propyl) acrylamide)/DMAPAAQ (N, N-Dimethyl amino propyl acrylamide, methyl chloride quaternary) hydrogels via free radical polymerization. Subsequently, we conducted experiments on this hydrogel for growing vegetables under cadmium stress conditions in aqueous solutions and soil. The cadmium capture capacity of DMAPAA/DMAPAAQ hydrogels under different cadmium ion concentrations and pH values was evaluated by using inductively coupled plasma optical emission spectrometry (ICP). The research results show that under the condition of pH = 7.3, the cadmium capture capacity of DMAPAA/DMAPAAQ hydrogels is the greatest. We used the Langmuir model to fit the adsorption data, and the correlation coefficient was as high as 0.96, indicating that the model fits well. The application of the hydrogels promoted the growth of vegetables in soil under cadmium stress conditions. The results showed that when the added amount of hydrogel was 4%, the dry weight of the vegetables was the largest. In addition, when the added amount of cadmium was 500 mg/kg and the added amount of hydrogel was 4%, the absorption of cadmium by the vegetables decreased to an undetectable level. In summary, the hydrogel successfully synthesized in this study can be effectively used to immobilize cadmium ions in soil while positively promoting the growth and yield of vegetables. This achievement has practical significance for solving the problem of heavy metal ion pollution.

Triple Cross-linked Dynamic Responsive Hydrogel Loaded with Selenium Nanoparticles for Modulating the Inflammatory Microenvironment via PI3K/Akt/NF-κB and MAPK Signaling Pathways

Modulating the inflammatory microenvironment can inhibit the process of inflammatory diseases (IDs). A tri-cross-linked inflammatory microenvironment-responsive hydrogel with ideal mechanical properties achieves triggerable and sustained drug delivery and regulates the inflammatory microenvironment. Here, this study develops an inflammatory microenvironment-responsive hydrogel (OD-PP@SeNPs) composed of phenylboronic acid grafted polylysine (PP), oxidized dextran (OD), and selenium nanoparticles (SeNPs). The introduction of SeNPs as initiators and nano-fillers into the hydrogel results in extra cross-linking of the polymer network through hydrogen bonding. Based on Schiff base bonds, Phenylboronate ester bonds, and hydrogen bonds, a reactive oxygen species (ROS)/pH dual responsive hydrogel with a triple-network is achieved. The hydrogel has injectable, self-healing, adhesion, outstanding flexibility, suitable swelling capacity, optimal biodegradability, excellent stimuli-responsive active substance release performance, and prominent biocompatibility. Most importantly, the hydrogel with ROS scavenging and pH-regulating ability protects cells from oxidative stress and induces macrophages into M2 polarization to reduce inflammatory cytokines through PI3K/AKT/NF-κB and MAPK pathways, exerting anti-inflammatory effects and reshaping the inflammatory microenvironment, thereby effectively treating typical IDs, including S. aureus infected wound and rheumatoid arthritis in rats. In conclusion, this dynamically responsive injectable hydrogel with a triple-network structure provides an effective strategy to treat IDs, holding great promise in clinical application.

Amoxicillin degradation and high-value extracellular polymer recovery by algal-bacterial symbiosis systems

Algal-bacterial symbiosis systems have emerged as sustainable methods for the treatment of new pollutants and the recovery of resources. However, the bio-refinery of biomass derived from microalgae is inefficient and expensive. In order to simultaneously degrade antibiotic and recover resources efficiently, two algal-bacterial symbiosis systems were constructed using Pseudomonas aeruginosa (alginate overproduction) and Bacillus subtilis (poly-γ-glutamic acid overproduction) with amoxicillin-degrading-microalga Prototheca zopfii W1. The optimal conditions for W1 to degrade amoxicillin are 35 °C, pH 7, and 180 rpm. In the presence of 5-50 mg/L of amoxicillin, W1-P. aeruginosa and W1-B. subtilis exhibit higher amoxicillin degradation and produce more extracellular polymers than W1 or bacteria alone. The metabolomic analysis demonstrates that the algal-bacterial symbiosis enhances the tolerance of W1 to amoxicillin by altering carbohydrate metabolism and promotes the production of biopolymers by upregulating the precursors synthesis. Moreover, the removal of amoxicillin (10 mg/L) from livestock effluent by W1-P. aeruginosa and W1-B. subtilis is greater than 90 % in 3 days, and the maximum yields of alginate and poly-γ-glutamate are 446.1 and 254.3 mg/g dry cell weight, respectively. These outcomes provide theoretical support for the application of algal-bacterial symbiosis systems to treatment of amoxicillin wastewater and efficient production of biopolymers.

In-situ conversion of geopolymer into novel floral magnetic sodalite microspheres for efficient removal of Cd(II) from water

In the present work, a novel, floral-like, magnetic sodalite microsphere (SODM) was synthesized in situ by using fly ash (FA) and metakaolin (MK) as raw materials and was used to remove Cd(II) from water. Its magnetism can solve the problems of adsorbent recovery and possible secondary pollution. During the static adsorption, SODM shows a maximum adsorption capacity of 245.17 mg/g. The adsorption of Cd(II) on the SODM surface is spontaneous, exothermic, and physicochemical adsorption, which was evaluated by thermodynamics, kinetics, and isotherm studies. During dynamic adsorption, SODM shows a maximum adsorption capacity of 342.74 mg/g in the simulated solution prepared by the deionized water, compared to 215.88 mg/g in the simulated solution prepared using Xiangsi Lake water from Guangxi Minzu University. At 0.5 g SODM dosage in the dynamic adsorption, the adsorption capacity could rise to 632.81 mg/g. These results demonstrated the excellent Cd (II) adsorption performance of the SODM. The adsorption of cadmium on the SODM surface includes the synergistic effects of electrostatic attraction, ion exchange, and surface coordination reaction. Besides, the SODM shows good regeneration performance in both the deionized water and Xiangsi Lake water. The present study explores SODM as an adsorbent for the Cd (II) removal from wastewater and unbolts the industrial applicability of the SODM in the field of wastewater purification.

Comparative study for removal of cationic and anionic dyes using alginate-based hydrogels filled with citric acid-sawdust/UiO-66-NH2 hybrid

Nowadays, a big challenge is developing a sustainable and effective method for removing contaminants like dyes from aqueous solutions. In this regard, Zr-based metal-organic framework (UiO-66-NH₂) and sawdust as the ideal adsorbents were used. Due to their low separation in adsorption processes, embedding into alginate and obtaining composite beads are suggested as a suitable strategy. The achieved Ca-alginate/citric acid (CA)-sawdust/UiO-66-NH₂ hydrogel beads were used to compare cationic and anionic dyes removal. This sorbent indicated an excellent selectivity for removing methylene blue versus methyl orange in a binary system. pH = 6, adsorbent amount = 80 mg, methylene blue concentration = 10 mg/L, and contact time = 420 min were achieved as optimal parameters on methylene blue adsorption with an adsorption capacity of about 26 mg/g. The removal process of methylene blue followed linear Freundlich isotherm and nonlinear pseudo-2nd-order kinetic models. The regeneration test demonstrated methylene blue removal efficiency higher than about 89 % after 9 cycles. According to the outcomes, methylene blue could be attached to the adsorbent surface through the electrostatic, hydrogen bonding, and π-π interactions of the aromatic rings. These results confirm the potential of Ca-alginate/CA-sawdust/UiO-66-NH₂ hydrogel beads as a selective bio-sorbent for cationic dye removal.

Green and Superior Adsorbents Derived from Natural Plant Gums for Removal of Contaminants: A Review

The ubiquitous presence of contaminants in water poses a major threat to the safety of ecosystems and human health, and so more materials or technologies are urgently needed to eliminate pollutants. Polymer materials have shown significant advantages over most other adsorption materials in the decontamination of wastewater by virtue of their relatively high adsorption capacity and fast adsorption rate. In recent years, "green development" has become the focus of global attention, and the environmental friendliness of materials themselves has been concerned. Therefore, natural polymers-derived materials are favored in the purification of wastewater due to their unique advantages of being renewable, low cost and environmentally friendly. Among them, natural plant gums show great potential in the synthesis of environmentally friendly polymer adsorption materials due to their rich sources, diverse structures and properties, as well as their renewable, non-toxic and biocompatible advantages. Natural plant gums can be easily modified by facile derivatization or a graft polymerization reaction to enhance the inherent properties or introduce new functions, thus obtaining new adsorption materials for the efficient purification of wastewater. This paper summarized the research progress on the fabrication of various gums-based adsorbents and their application in the decontamination of different types of pollutants. The general synthesis mechanism of gums-based adsorbents, and the adsorption mechanism of the adsorbent for different types of pollutants were also discussed. This paper was aimed at providing a reference for the design and development of more cost-effective and environmentally friendly water purification materials.

Polysaccharide-Based Composite Hydrogels as Sustainable Materials for Removal of Pollutants from Wastewater

Nowadays, pollution has become the main bottleneck towards sustainable technological development due to its detrimental implications in human and ecosystem health. Removal of pollutants from the surrounding environment is a hot research area worldwide; diverse technologies and materials are being continuously developed. To this end, bio-based composite hydrogels as sorbents have received extensive attention in recent years because of advantages such as high adsorptive capacity, controllable mechanical properties, cost effectiveness, and potential for upscaling in continuous flow installations. In this review, we aim to provide an up-to-date analysis of the literature on recent accomplishments in the design of polysaccharide-based composite hydrogels for removal of heavy metal ions, dyes, and oxyanions from wastewater. The correlation between the constituent polysaccharides (chitosan, cellulose, alginate, starch, pectin, pullulan, xanthan, salecan, etc.), engineered composition (presence of other organic and/or inorganic components), and sorption conditions on the removal performance of addressed pollutants will be carefully scrutinized. Particular attention will be paid to the sustainability aspects in the selected studies, particularly to composite selectivity and reusability, as well as to their use in fixed-bed columns and real wastewater applications.