The viscoelastic behavior of the precursor hydrogels can modify aerogel properties

Sustainable aerogels based on biobased poly (itaconic acid) for adsorption of cationic dyes

This work reports the synthesis of poly (itaconic acid) by thermal polymerization mediated by 2,2'-Azobis(2-methylpropionamidine) dihydrochloride. Furthermore, physical hydrogels were prepared by using high molecular weight poly (itaconic acid) characterized by low dispersity and laponite RD. The hydrogels presented porous 3D network structures, with a high-water penetration of almost 2000 g/g of swelling ratio, which can allow the adsorption sites of both poly (itaconic acid) and laponite RD to be easily exposed and facilitate the adsorption of dyes. The water adsorption followed Schott's pseudo-second-order model. The mechanism of the adsorption process was investigated using 1H and 31P NMR. The hydrogel is able to fast adsorb by a combination of electrostatic interactions and hydrogen bonding by the synergic effect of the clay and poly (itaconic acid). Moreover, the prepared aerogels exhibited a fast removal of Basic Fuchsin, with an adsorption capacity of 67.56 mg/g and a high removal efficiency (~99 %). The adsorption followed the pseudo-second-order kinetic model and Langmuir isotherm model. Furthermore, the thermodynamic parameters showed that the BF process of adsorption was spontaneous and feasible, endothermic, and followed physisorption. These results indicated that the PIA/laponite-based aerogel can be considered a promising adsorbent material in textile wastewater treatment.

Supercritical impregnation of starch aerogels with quercetin: Fungistatic effect and release modelling with a compartmental model

This work proposes the use of supercritical CO2 to impregnate starch (potato and corn) aerogels with quercetin for a potential fungistatic application. Starch aerogels were successfully produced with supercritical drying, but different results were found depending on the amylose/amylopectin ratio. A higher amount of amylose increases aerogels' specific surface area (with a structure with nanofibrils and nodes) due to the linear and amorphous character of this polymer, whereas a higher amount of amylopectin decreases this property until values of only 25 m2·g-1, obtaining an aerogel with a rough surface. These results were explained with XRD, thermogravimetric, and rheological results (triple step with two temperature sweeps and a time sweep and steady state analysis) concerning hydrogel formation. In fact, retrogradation step plays a more important role in hydrogel formation for a starch source with a higher amount of amylopectin due to an increase in the different polymers' interactions. Supercritical impregnation of quercetin on the aerogels was successfully performed (a loading around 0.30 % with respect to the amount of polymer), and in vitro results indicated that the aerogels produced a fungistatic effect on different types of fungi, but only in the first 12 h because the microorganisms adapted to the surrounding environment. Finally, a compartmental model was used to fit the drug release, which is controlled by quercetin aqueous solubility, indicating the main mass transfer resistances (mass transfer through aerogels was always around 500 min-1 and dissolution process mass transfer from 5·10-3 to 1.65·10-3 s-1) and how an increase in the specific surface area of the aerogels (in the case of corn aerogel) provided a stronger initial burst (70-80 % in 20 min). In fact, this initial burst release was mathematically related to a parameter, that varies from 0.178 to 0.036 depending on the aerogel composition. This study shows that starch aerogels can be impregnated with a hydrophobic compound with fungistatic effect by using supercritical CO2, modifying in addition the drug release by changing the native starch.

Validation of a compartmental model to predict drug release from porous structures produced by ScCO2 techniques

A global release model is proposed to study the drug release from porous materials for pharmaceutical applications. This model is defined by implementing a compartmental model where the release profile could be explained as the combination of mass transfer phenomena through three compartments as well as a desorption process or dissolution process from the support. This model was validated with five different systems produced with supercritical CO₂ (aerogels, membranes, and fibers), showing different release processes. Numerical results indicate that this compartmental approach can be useful to determine adsorption and desorption constants as well as mass transfer resistances within the material. Likewise, this model can predict lag phases and imbibition phenomena. Therefore, the development of compartmental models can be an alternative to traditional models to successfully predict the drug profile of porous materials, achieving a complete understanding of the involved phenomena regardless of the material characteristics.