Uranium monitoring tool for rapid analysis of environmental samples based on automated liquid-liquid microextraction

A liquid micro-extraction based one-step method for the chemical fractionation of copper in seawater

In this work, the reagent Cyanex® 272 has been incorporated in a three-phase solvent bar micro-extraction system to selectively separate the inorganic and organic fractions of copper in seawater. Optimized conditions for micro-extraction of Cu fractions were 0.2 M Cyanex® 272 in the organic solution contained into the fiber pores, 0.5 M HCl as acceptor solution within the fiber, stirring rate of 500 rpm, and 60 min time of extraction, providing an enrichment factor of 51.6 ± 2.3. Experimental results for selective extraction of organic and inorganic Cu showed a good correlation with theoretical data for Cu speciation, and the relationship between enrichment factor and dissolved organic carbon (DOC) concentration in the samples was used to predict total Cu concentration. Instrumental determination of Cu presented a linear response within the range 0.1-20 µg L^-1, obtaining a limit of detection of 0.03 µg L^-1. Finally, the method was successfully applied to the study of Cu fractions in real seawater samples collected from the Bay of Cádiz (Spain).

In-syringe dispersive liquid-liquid microextraction

Dispersive liquid-liquid microextraction (DLLME) has recently been widely used in the separation and preconcentration of various chemical species. Among the various approaches using DLLME are systems that use a syringe as an extraction environment. In this review, details of some methods that use this approach are presented. The ways to promote dispersion, analytical characteristics, and the advantages and disadvantages of the methods, among other aspects, are discussed critically. Finally, some trends in the use of in-syringe microextraction systems are described.

Automatic multicommuted flow systems applied in sample treatment for radionuclide determination in biological and environmental analysis

The presence of artificial and natural radioactivity in the environment is currently a topic of great relevance and ecological interest, even in human health issue, due to the increase of different anthropogenic activities. The use of multicommuted flow analysis techniques (e.g. Multi-Syringe Flow Injection Analysis - MSFIA, Lab-On-Valve - LOV and Lab-In-Syringe - LIS) has allowed the automation of radiochemical procedures to separate and preconcentrate radionuclides in environmental and biological samples. In comparison with the manual approach commonly used in routine analysis for radioactivity monitoring, the automation has enabled the development of highly reproducible methodologies with a great analysis frequency. Moreover, during the analytical procedure, the intervention of the analyst is drastically reduced, minimizing the radiological risk. The automation also offers significant advantages such as minimum consumption of time and reagents, reducing the cost and the generation of waste, contributing to the green chemistry. In this review, several multicommuted flow analysis techniques (MSFIA, LOV and LIS) reported in the last decade applied for the development of automatic sample treatment methodologies, used to separate, preconcentrate and quantify ⁹⁰Sr, ⁹⁹Tc, natural U and ²²⁶Ra in biological and environmental samples are described and critically compared.

An automated system for preconcentration on imprinted polymer and laser diode spectrometric determination of uranium in mineral water samples

A study, where uranium was online enriched and laser diode spectrometry was determined, was performed with some bottled mineral water samples. A uranium-imprinted polymer (PMDU) was synthesized and characterized for preparation of a specific adsorbent of UO₂²⁺ cations. The homemade system preconcentrated uranium in PMDU resin and determined using an Arsenazo III complex at 650 nm in a combined laser diode spectrometer. All analytical parameters of the system were optimized at 5.5 of the retention pH, 6.0 N HClO₄ of eluent concentration, 0.05% of Arsenazo III complex, and a 40 mm coil length. The effect of interferent ions was also investigated and LOD and LOQ values were found to be 0.54 and 1.80 ng mL^-1 respectively. Sample throughput was 12 h^-1, the preconcentration factor was 50, and RSD% value was 1.1. Certified reference materials of TMDA 52.3 and TMDA 62.2 were quantitatively analyzed and the proposed method was successfully applied to the bottled mineral water samples.

Dynamic Flow Approaches for Automated Radiochemical Analysis in Environmental, Nuclear and Medical Applications

Automated sample processing techniques are desirable in radiochemical analysis for environmental radioactivity monitoring, nuclear emergency preparedness, nuclear waste characterization and management during operation and decommissioning of nuclear facilities, as well as medical isotope production, to achieve fast and cost-effective analysis. Dynamic flow based approaches including flow injection (FI), sequential injection (SI), multi-commuted flow injection (MCFI), multi-syringe flow injection (MSFI), multi-pumping flow system (MPFS), lab-on-valve (LOV) and lab-in-syringe (LIS) techniques have been developed and applied to meet the analytical criteria under different situations. Herein an overall review and discussion on these techniques and methodologies developed for radiochemical separation and measurement of various radionuclides is presented. Different designs of flow systems with combinations of radiochemical separation techniques, such as liquid-liquid extraction (LLE), liquid-liquid microextraction (LLME), solid phase extraction chromatography (SPEC), ion exchange chromatography (IEC), electrochemically modulated separations (EMS), capillary electrophoresis (CE), molecularly imprinted polymer (MIP) separation and online sensing and detection systems, are summarized and reviewed systematically.