Discrimination and quantification of two isomeric antineoplastic drugs by rapid and non-invasive analytical control using a handheld Raman spectrometer

Fully Integrated Ultrathin Solid Immersion Grating Microspectrometer for Handheld Visible and Near-Infrared Spectroscopic Applications

Despite advances in microfabrication, compact spectrometers still face challenges in shrinking their size without sacrificing optical performance. Here,  the solid immersion grating microspectrometer (SIG-µSPEC) for high spectral resolution in a broad operational wavelength range is reported. The spectroscopic module incorporates a silicon microslit, index-matched lens, plane mirrors, solid immersion grating (SIG), and a CMOS line sensor within a small form factor. The SIG facilitates high angular dispersion of light on a planar focal plane, resulting in an average spectral resolution of 5.8 nm, with over 76% maximum sensitivity from 400 to 800 nm. SIG-µSPEC measures the spectral reflectance of fruits at different ripening stages, clearly revealing changes in the chlorophyll absorption band. The measured spectrum is further utilized for the precise prediction of the soluble solid content (SSC) levels, achieving a high correlation (R2 = 0.91) and a ratio of prediction-to-deviation of 2.36. This compact microspectrometer holds the potential for precise and non-invasive spectral analysis across point-of-care fields.

Quantification of clinical mAb solutions using Raman spectroscopy: Macroscopic vs microscopic analysis

Raman Spectroscopy is well emerged in the field of Analytical Quality Control (AQC) as a rapid and cost-effective technique useful in many applications. The advantage of Raman spectroscopy is the non-invasiveness of measurements that enablesto analyse samples directly in its container. In this study, the potential of Raman spectroscopy was investigated for analysis of clinical preparations of mAbs. Three commercial formulations of monoclonal antibodies (mAbs) Avastin®, Ontruzant® and Tecentriq® corresponding to Bevacizumab (BVC), Trastuzumab (TRS) and Atezolizumab (ATZ) respectively, were analysed in quartz cuvette in macroscopic analysis and through the wall of perfusion bags in microscopic analysis. The spectra have been compared to those of excipients (trehalose and sucrose) and of γ-Globulin, in order to investigate the origin of Raman bands. As expected, Raman spectra were a combination of bands from monoclonal antibodies and correspoding excipients found in formulas. For quantitative analysis of the solutions, models have been constructed using Partial Least Square Regression (PLSR) with Leave K-Out Cross Validation (LKOCV). The quantification performance was comparable for both macroscopic and microscopic analysis, in terms of error and linearity. The results are thus promising for future AQC in situ, in perfusion bags.

Epirubicin: Biological Properties, Analytical Methods, and Drug Delivery Nanosystems

Epirubicin (EPI) is a chemotherapeutic agent belonging to the anthracycline drug class indicated for treating several tumors. It acts by suppressing the DNA and RNA synthesis by intercalating between their base pair. However, several side effects are associated with this therapy, including cardiotoxicity and myelosuppression. Therefore, EPI delivery in nanosystems has been an interesting strategy to overcome these limitations and improve the safety and efficacy of EPI. Thus, analytical methods have been used to understand and characterize these nanosystems, including spectrophotometric, spectrofluorimetric, and chromatography. Spectrophotometric and spectrofluorimetric methods have been used to quantify EPI in less complex matrices due to their efficiency, low cost, and green chemistry character. By contrast, high-performance liquid chromatography is a suitable method for detecting EPI in more complex matrices (e.g., plasm and urine) owing to its high sensitivity. This review summarizes physicochemical and pharmacokinetic properties of EPI, its application in drug delivery nanosystems, and the analytical methods employed in its quantification in different matrices, including blood, plasm, urine, and drug delivery nanosystems.

Analysis of IV Drugs in the Hospital Workflow by Raman Spectroscopy: The Case of Piperacillin and Tazobactam

Medical errors associated with IV preparation and administration procedures in a hospital workflow can even cost human lives due to the direct effect they have on patients. A large number of such incidents, which have been reported in bibliography up to date, indicate the urgent need for their prevention. This study aims at proposing an analytical methodology for identifying and quantifying IV drugs before their administration, which has the potential to be fully harmonized with clinical practices. More specifically, it reports on the analysis of a piperacillin (PIP) and tazobactam (TAZ) IV formulation, using Raman spectroscopy. The simultaneous analysis of the two APIs in the same formulation was performed in three stages: before reconstitution in the form of powder without removing the substance out of the commercial glass bottle (non-invasively), directly after reconstitution in the same way, and just before administration, either the liquid drug is placed in the infusion set (on-line analysis) or a minimal amount of it is transferred from the IV bag to a Raman optic cell (at-line analysis). Except for the successful identification of the APIs in all cases, their quantification was also achieved through calibration curves with correlation coefficients ranging from 0.953 to 0.999 for PIP and from 0.965 to 0.997 for TAZ. In any case, the whole procedure does not need more than 10 min to be completed. The current methodology, based on Raman spectroscopy, outweighs other spectroscopic (UV/Vis, FT-IR/ATR) or chromatographic (HPLC, UHPLC) protocols, already applied, which are invasive, costly, time-consuming, not environmentally friendly, and require specialized staff and more complex sample preparation procedures, thus exposing the staff to hazardous materials, especially in cases of cytotoxic drugs. Such an approach has the potential to bridge the gap between experimental setup and clinical implementation through exploitation of already developed handheld devices, along with the presence of digital spectral libraries.

Axially slanted laser illumination scheme for direct and accurate Raman spectroscopic determination of gemcitabine concentration in freeze-dried gemcitabine injection powder housed in a glass container

When Raman spectroscopy is employed for a direct in situ determination of ingredient concentration for a product stored in a glass container, minimization of the interfering glass background in the collected spectrum is demanding to secure a more accurate analysis. To meet this request, an axially slanted illumination (ASI) scheme slantingly irradiating laser on the headspace side of a glass container and positioning a detector beneath the container was demonstrated in this study. This ASI scheme was basically designed to increase the distance between the laser illumination spot and detector location to minimize the number of glass photons reaching the detector. The analytical utility of the scheme was evaluated for the determination of gemcitabine concentration (42.9-58.2 wt%) in the gemcitabine injection powder housed in a glass container. Using the ASI scheme, the spectral features of the gemcitabine powder became distinct with only a weak underlying glass background signal. For comparative purpose, when an axially perpendicular offset (APO) scheme perpendicularly irradiating laser on the side wall where the sample was filled was used, the magnitude of glass background was higher, and the most intense gemcitabine peak was largely buried in the glass peak. The accuracy for determination of gemcitabine concentration using the ASI scheme was superior with an error of 0.20 wt%, while 0.33 wt% with employing the APO scheme. Overall, this study demonstrates that the ASI scheme is a potentially versatile Raman spectroscopic tool for fast non-sampling analysis of other products stored in a glass container.

In situ Analytical Quality Control of chemotherapeutic solutions in infusion bags by Raman spectroscopy

Analytical Quality Control (AQC) in centralised preparation units of oncology centers is a common procedure relying on the identification and quantification of the prepared chemotherapeutic solutions for safe intravenous administration to patients. Although the use of Raman spectroscopy for AQC has gained much interest, in most applications it remains coupled to a flow injection analyser (FIA) requiring withdrawal of the solution for analysis. In addition to current needs for more rapid and cost-effective analysis, the risk of exposure of clinical staff to the toxic molecules during daily handling is a serious concern to address. Raman spectroscopic analysis, for instance by Confocal Raman Microscopy (CRM), could enable direct analysis (non-invasive) for AQC directly in infusion bags. In this study, 3 anticancer drugs, methotrexate (MTX), 5-fluorouracil (5-FU) and gemcitabine (GEM) have been selected to highlight the potential of CRM for withdrawal free analysis. Solutions corresponding to the clinical range of each drug were prepared in 5% glucose and data was collected from infusion bags placed under the Raman microscope. Firstly, 100% discrimination has been obtained by Partial Least Squares Discriminant Analysis (PLS-DA) confirming that the identification of drugs can be performed. Secondly, using Partial Least Squares Regression (PLSR), quantitative analysis was performed with mean % error of predicted concentrations of respectively 3.31%, 5.54% and 8.60% for MTX, 5-FU and GEM. These results are in accordance with the 15% acceptance criteria used for the current clinical standard technique, FIA, and the Limits of Detection for all drugs were determined to be substantially lower than the administered range, thus highlighting the potential of confocal Raman spectroscopy for direct analysis of chemotherapeutic solutions.

Chemometric Analysis of UV-Visible Spectral Fingerprints for the Discrimination and Quantification of Clinical Anthracycline Drug Preparation Used in Oncology

In clinical treatment, the analytical quality assessment of the delivery of chemotherapeutic preparations is required to guarantee the patient's safety regarding the dose and most importantly the appropriate anticancer drug. On its own, the development of rapid analytical methods allowing both qualitative and quantitative control of the formulation of prepared solutions could significantly enhance the hospital's workflow, reducing costs, and potentially providing optimal patient care. UV-visible spectroscopy is a nondestructive, fast, and economical technique for molecular characterization of samples. A discrimination and quantification study of three chemotherapeutic drugs doxorubicin, daunorubicin, and epirubicin was conducted, using clinically relevant concentration ranges prepared in 0.9% NaCl solutions. The application of the partial least square discriminant analysis PLS-DA method on the UV-visible spectral data shows a perfect discrimination of the three drugs with a sensitivity and specificity of 100%. The use of partial least square regression PLS shows high quantification performance of these molecules in solution represented by the low value of root mean square error of calibration (RMSEC) and root mean square error of cross validation (RMSCECV) on the one hand and the high value of R-square on the other hand. This study demonstrated the viability of UV-visible fingerprinting (routine approach) coupled with chemometric tools for the classification and quantification of chemotherapeutic drugs during clinical preparation.

A mathematical approach to deal with nanoparticle polydispersity in surface enhanced Raman spectroscopy to quantify antineoplastic agents

Antineoplastic agents are, for most of them, highly toxic drugs prepared at hospital following individualized prescription. To protect patients and healthcare workers, it is important to develop analytical tools able to identify and quantify such drugs on a wide concentration range. In this context, surface enhanced Raman spectroscopy (SERS) has been tested as a specific and sensitive technique. Despite the standardization of the nanoparticle synthesis, a polydispersity of nanoparticles in the suspension and a lack of reproducibility persist. This study focuses on the development of a new mathematical approach to deal with this nanoparticle polydispersity and its consequences on SERS signal variability through the feasibility of 5-fluorouracil (5FU) quantification using silver nanoparticles (AgNPs) and a handled Raman spectrophotometer. Variability has been maximized by synthetizing six different batches of AgNPs for an average size of 24.9 nm determined by transmission electron microscopy, with residual standard deviation of 17.0%. Regarding low performances of the standard multivariate data processing, an alternative approach based on the nearest neighbors were developed to quantify 5FU. By this approach, the predictive performance of the 5FU concentration was significantly improved. The mean absolute relative error (MARE) decreased from 16.8% with the traditional approach based on PLS regression to 6.30% with the nearest neighbors approach (p-value < 0.001). This study highlights the importance of developing mathematics adapted to SERS analysis which could be a step to overcome the spectral variability in SERS and thus participate in the development of this technique as an analytical tool in quality control to quantify molecules with good performances, particularly in the pharmaceutical field.

Identification and Confirmation of Fentanyls on Paper using Portable Surface Enhanced Raman Spectroscopy and Paper Spray Ionization Mass Spectrometry

Fentanyl and its analogues play a major role in the current opioid epidemic. In particular, these highly potent opioids have become a health hazard due to their use as additives in street drugs. Consequently, rapid on-site procedures for the analysis of this class of seized drugs are needed, especially considering the reported backlog of drug samples, which must undergo identification and confirmation tests to validate the presence of an illicit substance. Paper based devices are cheap sampling and analysis vehicles that have been shown capable of allowing rapid identification and confirmation of drugs of abuse. Modifying paper substrates by imprinting nanoparticles enables surface enhanced Raman spectroscopy (SERS) as well as a second analysis from the same substrate, namely paper spray ionization mass spectrometry. While such a procedure has been described for laboratory use, these illicit drug samples are typically collected in the field and this is where testing should be done. We combine paper SERS and paper spray MS on field-portable and commercial off-the-shelf (COTS) devices for the rapid and low-cost identification and confirmation of fentanyl and its analogues, enabling in situ analysis at the point of seizure of suspect samples. The commercial nature of both instruments moves this technology from the academic realm to a setting where the criminal justice system can realistically utilize it. The capabilities of this single-substrate dual-analyzer technique are further examined by sampling a variety of surfaces of forensic interest.

Qualitative and quantitative analysis of therapeutic solutions using Raman and infrared spectroscopy

Anticancer drugs are prescribed and administrated to an increasing number of patients on a daily basis. As a consequence, a number of concerns have been raised about the patient health and safety in the case that the drugs administered are not at the required concentration or even worse not the correct ones. Quality control of therapeutic solutions has therefore been extensively implemented in hospital environments, in order to avoid any failure in the intense workflow faced by administering pharmacists. In the present study, infrared (IR) and Raman spectroscopy have been employed for the analysis of 3 commercially available therapeutic solutions TEVA®, MYLAN®, CERUBIDINE®, respectively containing doxorubicin, epirubicin and daunorubicin. They perfectly illustrate the analytical difficulties encountered, as these 3 chemotherapeutic drugs are isomers, hardly distinguishable with conventional approaches such as UV/VIS spectrometry. Any analytical failure to identify these molecules can lead to delays in patient treatment. While Partial Least Squares Regression analysis demonstrates that both Raman and IR can deliver satisfactory quantitative analysis in the clinical range, with respective Root Mean Square Error of Cross Validation (RMSECV) between 0.0127 - 0.0220 g·L^-1 and 0.0573 - 0.0759 g·L^-1, the identification rate between the 2 techniques differs substantially. Indeed, Principal Component Analysis - Factorial Discriminant Analysis (PCA-FDA) highlights that, depending on the data preprocessing applied to Raman spectra, the discrimination between the 3 drugs is decreased, with in some cases specificity and sensitivity below 50%. However, IR analysis displays encouraging results with an overall specificity and sensitivity between 99 and 100%, suggesting that reliable validation of the therapeutic solution for administration to patients can be achieved. IR and Raman spectroscopy could assist and support quality control of chemotherapeutic solutions prepared in personalised concentrations for each patient. The effective and reliable characterisation of therapeutic solutions could have a lot to offer to improve current practices in a near future.

Process analytical technologies and injectable drug products: Is there a future?

Parametric release was the first subset of real time release testing (RTRT), applied to terminally sterilised injectable drug products. The objective was to offer the industry an alternative to the time and money consuming sterility testing, without compromising the sterility of the products. The rationale was that quality cannot be tested into products, instead it must be planned (the principle of quality by design, QbD). This can be implemented by setting appropriate in-process controls supported on process analytical technologies (PAT). Two of the most versatile and promising PAT tools are the near infrared spectroscopy (NIRS) and the Raman spectroscopy. However, their application to injectable drug product development and manufacturing has been scarce. This review has the objective to provide a framework for the practical implementation of the QbD approach to injectable formulations, including application of diverse risk assessment and factorial design tools. Finally, the actual application of PAT, namely NIRS and Raman spectroscopy, to injectable drug product analysis is addressed.

Field detection devices for screening the quality of medicines: a systematic review

BACKGROUND

Poor quality medicines have devastating consequences. A plethora of innovative portable devices to screen for poor quality medicines has become available, leading to hope that they could empower medicine inspectors and enhance surveillance. However, information comparing these new technologies is woefully scarce.

METHODS

We undertook a systematic review of Embase, PubMed, Web of Science and SciFinder databases up to 30 April 2018. Scientific studies evaluating the performances/abilities of portable devices to assess any aspect of the quality of pharmaceutical products were included.

RESULTS

Forty-one devices, from small benchtop spectrometers to 'lab-on-a-chip' single-use devices, with prices ranging from US$20 000, were included. Only six devices had been field-tested (GPHF-Minilab, CD3/CD3+, TruScan RM, lateral flow dipstick immunoassay, CBEx and Speedy Breedy). The median (range) number of active pharmaceutical ingredients (APIs) assessed per device was only 2 (1-20). The majority of devices showed promise to distinguish genuine from falsified medicines. Devices with the potential to assay API (semi)-quantitatively required consumables and were destructive (GPHF-Minilab, PharmaChk, aPADs, lateral flow immunoassay dipsticks, paper-based microfluidic strip and capillary electrophoresis), except for spectroscopic devices. However, the 10 spectroscopic devices tested for their abilities to quantitate APIs required processing complex API-specific calibration models. Scientific evidence of the ability of the devices to accurately test liquid, capsule or topical formulations, or to distinguish between chiral molecules, was limited. There was no comment on cost-effectiveness and little information on where in the pharmaceutical supply chain these devices could be best deployed.

CONCLUSION

Although a diverse range of portable field detection devices for medicines quality screening is available, there is a vitally important lack of independent evaluation of the majority of devices, particularly in field settings. Intensive research is needed in order to inform national medicines regulatory authorities of the optimal choice of device(s) to combat poor quality medicines.

Discriminative and Quantitative Analysis of Antineoplastic Taxane Drugs Using a Handheld Raman Spectrometer

This study was conducted to evaluate the ability of Raman spectroscopy (RS) to control antineoplastic preparations used for chemotherapy in order to ensure its physical and chemical qualities. Three taxane drugs: cabazitaxel (CBX), docetaxel (DCX) and paclitaxel (PCX) at therapeutic concentration ranges were analyzed using a handheld spectrometer at 785 nm. Qualitative and quantitative models were developed and optimized using a calibration set (n=75 per drug) by partial least square discriminant analysis and regression and validated using a test set (n=27 per drug). All samples were correctly assigned with an accuracy of 100%. Despite optimization, quantitative analysis showed limited performances at the lowest concentrations. The root mean square error of predictions ranged from 0.012 mg/mL for CBX to 0.048 mg/mL for DCX with a minimal coefficient of determination of 0.9598. The linearity range was validated from 0.175 to 0.30 mg/mL for CBX, from 0.40 to 1.00 mg/mL for DCX and from 0.57 to 1.20 mg/mL for PCX. Despite some limitations, this study confirms the potential of RS to control these drugs and also provides substantial advantages to secure the activity for healthcare workers. As a result of its rapidity and the uncomplicated use of a handheld instrument, RS appears to be a promising method to augment security of the medication preparation process in hospitals.

Rapid discrimination and quantification analysis of five antineoplastic drugs in aqueous solutions using Raman spectroscopy

The aim of this study was to assess the ability of Raman spectroscopy to discriminate and quantify five antineoplastic drugs in an aqueous matrix at low concentrations before patient administration. Five antineoplastic drugs were studied at therapeutic concentrations in aqueous 0.9% sodium chloride: 5-fluorouracil (5FU), gemcitabine (GEM), cyclophophamide (CYCLO), ifosfamide (IFOS) and doxorubicin (DOXO). All samples were packaged in glass vials and analyzed using Raman spectrometry from 400 to 4000cm^-1. Discriminant analyses were performed using Partial Least Squares Discriminant Analysis (PLS-DA) and quantitative analyses using PLS regression. The best discrimination model was obtained using hierarchical PLS-DA models including three successive models for concentrations higher than the lower limit of quantification (0% of fitting and cross-validation error rate with an excellent accuracy of 100%). According to these hierarchical discriminative models, 90.8% (n=433) of external validation samples were correctly predicted, 2.5% (n=12) were misclassified and 6.7% (n=32) of the external validation set were not assigned. The quantitative analysis was characterized by the RMSEP that ranged from 0.23mg/mL for DOXO to 3.05mg/mL for 5FU. The determination coefficient (R²) was higher than 0.9994 for all drugs evaluated except for 5FU (R²=0.9986). This study provides additional information about the potential value of Raman spectroscopy for real-time quality control of cytotoxic drugs in hospitals. In some situations, this technique therefore constitutes a powerful alternative to usual methods with ultraviolet (UV) detection to ensure the correct drug and the correct dose in solutions before administration to patients and to limit exposure of healthcare workers during the analytical control process.

Quantitative analysis of curcumin-loaded alginate nanocarriers in hydrogels using Raman and attenuated total reflection infrared spectroscopy

Core-shell nanocarriers are increasingly being adapted in cosmetic and dermatological fields, aiming to provide an increased penetration of the active pharmaceutical or cosmetic ingredients (API and ACI) through the skin. In the final form, the nanocarriers (NC) are usually prepared in hydrogels, conferring desired viscous properties for topical application. Combined with the high chemical complexity of the encapsulating system itself, involving numerous ingredients to form a stable core and quantifying the NC and/or the encapsulated active without labor-intensive and destructive methods remains challenging. In this respect, the specific molecular fingerprint obtained from vibrational spectroscopy analysis could unambiguously overcome current obstacles in the development of fast and cost-effective quality control tools for NC-based products. The present study demonstrates the feasibility to deliver accurate quantification of the concentrations of curcumin (ACI)-loaded alginate nanocarriers in hydrogel matrices, coupling partial least square regression (PLSR) to infrared (IR) absorption and Raman spectroscopic analyses. With respective root mean square errors of 0.1469 ± 0.0175% w/w and 0.4462 ± 0.0631% w/w, both approaches offer acceptable precision. Further investigation of the PLSR results allowed to highlight the different selectivity of each approach, indicating only IR analysis delivers direct monitoring of the NC through the quantification of the Labrafac®, the main NC ingredient. Raman analyses are rather dominated by the contribution of the ACI which opens numerous perspectives to quantify the active molecules without interferences from the complex core-shell encapsulating systems thus positioning the technique as a powerful analytical tool for industrial screening of cosmetic and pharmaceutical products. Graphical abstract Quantitative analysis of encapuslated active molecules in hydrogel-based samples by means of infrared and Raman spectroscopy.